Calling RF calibrations when interface up, connection, switching bands and
going to scan.
For 8922AE, RF calibrations are moved to firmware, so use H2C commands to
trigger RF calibrations and wait for a C2H event to indicate completion.
Then, do next RF calibration.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://msgid.link/20240202030642.108385-10-pkshih@realtek.com
TSSI is short for transmitter signal strength indication, which is a
close-loop hardware circuit to feedback actual transmitting power as a
reference to adjust power for next transmission.
When connecting and switching bands or channels, do TSSI calibration and
reset hardware status to output expected power.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://msgid.link/20240202030642.108385-9-pkshih@realtek.com
IQ signal calibration is a basic and important calibration to yield good RF
performance. Do this calibration on AP channel if we are going to connect.
During scanning phase, it transmits with low data rate, so without IQK
RF performance is still acceptable.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://msgid.link/20240202030642.108385-4-pkshih@realtek.com
The RF calibrations should be executed one by one, so add a completion
to ensure one is finish before next. The report from C2H event contains
state and optional version, and we only check the state for now. We also
care about the time a RF calibration takes, so record start time before
asking firmware to do calibration and get the delta time when receiving
report.
Consider SER recovery, we can't receive C2H event, use half of argument
'ms' as fixed delay that is 2 times of measured maximum time of
calibrations.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://msgid.link/20240202030642.108385-2-pkshih@realtek.com
The CW1200 uses two GPIOs to control the powerup and reset
pins, get these from GPIO descriptors instead of being passed
as platform data from boardfiles.
The RESET line will need to be marked as active low as we will
let gpiolib handle the polarity inversion.
The SDIO case is a bit special since the "card" need to be
powered up before it gets detected on the SDIO bus and
properly probed. Fix this by using board-specific GPIOs
assigned to device "NULL".
There are currently no in-tree users.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://msgid.link/20240131-descriptors-wireless-v1-6-e1c7c5d68746@linaro.org
Sparse warns:
drivers/net/wireless/st/cw1200/cw1200_spi.c:83:17: got restricted __le16 [usertype]
drivers/net/wireless/st/cw1200/cw1200_spi.c:148:17: warning: incorrect type in assignment (different base types)
drivers/net/wireless/st/cw1200/cw1200_spi.c:148:17: expected unsigned short [addressable] [assigned] [usertype] regaddr
drivers/net/wireless/st/cw1200/cw1200_spi.c:148:17: got restricted __le16 [usertype]
These cpu_to_le16() calls are not really making any sense to me. On a big
endian system we first convert regaddr from big to little using cpu_to_le16()
but immediately after we convert them back to big endian? So just remove them.
Compile tested only.
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://msgid.link/20240130151556.2315951-4-kvalo@kernel.org
drivers/net/wireless/rsi/rsi_91x_usb.c:235:27: warning: restricted __le32 degrades to integer
drivers/net/wireless/rsi/rsi_91x_usb.c:236:27: warning: restricted __le32 degrades to integer
drivers/net/wireless/rsi/rsi_91x_usb.c:237:27: warning: restricted __le32 degrades to integer
drivers/net/wireless/rsi/rsi_91x_usb.c:238:27: warning: restricted __le32 degrades to integer
drivers/net/wireless/rsi/rsi_91x_usb.c:244:36: warning: restricted __le32 degrades to integer
drivers/net/wireless/rsi/rsi_91x_usb.c:245:35: warning: restricted __le32 degrades to integer
These cpu_to_le32() are not making sense. With usb_reg_buf we handle the values
byte at a time to make sure usb_reg_buf is in little endian so no need to
convert anything. And usb_control_msg() expects to have the values in native
endian anyway. So just remove these so they are not spamming our logs.
Compile tested only.
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://msgid.link/20240130151556.2315951-3-kvalo@kernel.org
Sparse warns:
drivers/net/wireless/zydas/zd1211rw/zd_usb.c:383:24: warning: implicit cast from nocast type
drivers/net/wireless/zydas/zd1211rw/zd_usb.c:419:24: warning: implicit cast from nocast type
This is an ancient driver which has not have any meaningfuli changes for a long
time and hopefully removed soon. So just remove the __nocast to get rid of the
sparse warnings.
Compile tested only.
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://msgid.link/20240130151556.2315951-2-kvalo@kernel.org
In the for statement of lbs_allocate_cmd_buffer(), if the allocation of
cmdarray[i].cmdbuf fails, both cmdarray and cmdarray[i].cmdbuf needs to
be freed. Otherwise, there will be memleaks in lbs_allocate_cmd_buffer().
Fixes: 876c9d3aeb ("[PATCH] Marvell Libertas 8388 802.11b/g USB driver")
Signed-off-by: Zhipeng Lu <alexious@zju.edu.cn>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://msgid.link/20240126075336.2825608-1-alexious@zju.edu.cn
dmi_get_system_info() will statically return NULL when the
kernel is compiled without CONFIG_DMI, leading to compiler
warnings. Fix that by printing "<unknown>" in that case.
Fixes: c3f40c3e02 ("iwlwifi: mvm: add US/CA to TAS block list if OEM isn't allowed")
Fixes: 9457077df4 ("wifi: iwlwifi: mvm: Add debugfs to get TAS status")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When the system is compiled without CONFIG_DMI, the function
here statically returns NULL, leading to a compiler warning.
Catch that and print "<unknown>" in that case.
While at it, fix some indentation in the function.
Reported-by: kernel test robot <lkp@intel.com>
Closes: https://lore.kernel.org/oe-kbuild-all/202402030641.zUTuACYV-lkp@intel.com/
Fixes: 09059c6764 ("wifi: iwlwifi: prepare for reading PPAG table from UEFI")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
As DSMs are going to be read from UEFI too, we need a unified API
to get DSMs for both ACPI and UEFI.
The difference in getting DSM in each one of these methods (ACPI, UEFI)
is in the GUID, revision (0 for ACPI, 4 for UEFI), and size of the DSM
values (8 or 32 for ACPI, 32 for UEFI).
Therefore, change the iwl_acpi_get_dsm_x() to iwl_acpi_get_dsm() which
determines the GUID, revision (these two are the same for all WiFi DSMs),
and size (based on a func-to-size mapping) internally.
While at it, fix DSM_FUNC_RFI_CONFIG to expect a 32-bit value
(as defined in Intel BIOS spec) and not a 8-bit one.
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Reviewed-by: Gregory Greenman <gregory.greenman@intel.com>
Link: https://msgid.link/20240201155157.1bcd7072a7a5.I344ee0a11abbc27da0c693187d1b8bee653aaeef@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
