Daniel Machon says:
====================
net: microchip: add FDMA library and use it for Sparx5
This patch series is the first of a 2-part series, that adds a new
common FDMA library for Microchip switch chips Sparx5 and lan966x. These
chips share the same FDMA engine, and as such will benefit from a
common library with a common implementation. This also has the benefit
of removing a lot open-coded bookkeeping and duplicate code for the two
drivers.
Additionally, upstreaming efforts for a third chip, lan969x, will begin
in the near future. This chip will use the new library too.
In this first series, the FDMA library is introduced and used by the
Sparx5 switch driver.
###################
# Example of use: #
###################
- Initialize the rx and tx fdma structs with values for: number of
DCB's, number of DB's, channel ID, DB size (data buffer size), and
total size of the requested memory. Also provide two callbacks:
nextptr_cb() and dataptr_cb() for getting the nextptr and dataptr.
- Allocate memory using fdma_alloc_phys() or fdma_alloc_coherent().
- Initialize the DCB's with fdma_dcb_init().
- Add new DCB's with fdma_dcb_add().
- Free memory with fdma_free_phys() or fdma_free_coherent().
#####################
# Patch breakdown: #
#####################
Patch #1: introduces library and selects it for Sparx5.
Patch #2: includes the fdma_api.h header and removes old symbols.
Patch #3: replaces old rx and tx variables with equivalent ones from the
fdma struct. Only the variables that can be changed without
breaking traffic is changed in this patch.
Patch #4: uses the library for allocation of rx buffers. This requires
quite a bit of refactoring in this single patch.
Patch #5: uses the library for adding DCB's in the rx path.
Patch #6: uses the library for freeing rx buffers.
Patch #7: uses the library helpers in the rx path.
Patch #8: uses the library for allocation of tx buffers. This requires
quite a bit of refactoring in this single patch.
Patch #9: uses the library for adding DCB's in the tx path.
Patch #10: uses the library helpers in the tx path.
Patch #11: ditches the existing linked list for storing buffer addresses,
and instead uses offsets into contiguous memory.
Patch #12: modifies existing rx and tx functions to be direction
independent.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, the driver uses a linked list for storing the tx buffer
addresses. This requires a good amount of extra bookkeeping code. Ditch
the linked list in favor of tx buffers being in the same contiguous
memory space as the DCB's and the DB's. The FDMA library has a helper
for this - so use that.
The tx buffer addresses are now retrieved as an offset into the FDMA
memory space.
Signed-off-by: Daniel Machon <daniel.machon@microchip.com>
Reviewed-by: Steen Hegelund <Steen.Hegelund@microchip.com>
Reviewed-by: Jens Emil Schulz Østergaard <jensemil.schulzostergaard@microchip.com>
Reviewed-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the fdma_dcb_add() function to add DCB's in the tx path. This gets
rid of the open-coding of nextptr and dataptr handling and leaves it to
the library.
Also, make sure the fdma indexes are advanced using: fdma_dcb_advance(),
so that the correct nextptr and dataptr offsets are retrieved.
Signed-off-by: Daniel Machon <daniel.machon@microchip.com>
Reviewed-by: Steen Hegelund <Steen.Hegelund@microchip.com>
Reviewed-by: Jens Emil Schulz Østergaard <jensemil.schulzostergaard@microchip.com>
Reviewed-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the two functions: fdma_alloc_phys() and fdma_dcb_init() for tx
buffer allocation and use the new buffers throughout.
In order to replace the old buffers with the new ones, we have to do the
following refactoring:
- use fdma_alloc_phys() and fdma_dcb_init()
- replace the variables: tx->dma, tx->first_entry and tx->curr_entry
with the equivalents from the FDMA struct.
- replace uses of sparx5_db_hw and sparx5_tx_dcb_hw with fdma_db and
fdma_dcb.
- add sparx5_fdma_tx_dataptr_cb callback for obtaining the dataptr.
- Initialize FDMA struct values.
Signed-off-by: Daniel Machon <daniel.machon@microchip.com>
Reviewed-by: Steen Hegelund <Steen.Hegelund@microchip.com>
Reviewed-by: Jens Emil Schulz Østergaard <jensemil.schulzostergaard@microchip.com>
Reviewed-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the two functions: fdma_alloc_phys() and fdma_dcb_init() for rx
buffer allocation and use the new buffers throughout.
In order to replace the old buffers with the new ones, we have to do the
following refactoring:
- use fdma_alloc_phys() and fdma_dcb_init()
- replace the variables: rx->dma, rx->dcb_entries and rx->last_entry
with the equivalents from the FDMA struct.
- replace uses of sparx5_db_hw and sparx5_rx_dcb_hw with fdma_db and
fdma_dcb.
- add sparx5_fdma_rx_dataptr_cb callback for obtaining the dataptr.
- Initialize FDMA struct values.
Signed-off-by: Daniel Machon <daniel.machon@microchip.com>
Reviewed-by: Steen Hegelund <Steen.Hegelund@microchip.com>
Reviewed-by: Jens Emil Schulz Østergaard <jensemil.schulzostergaard@microchip.com>
Reviewed-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Replace the old rx and tx variables: channel_id, FDMA_DCB_MAX,
FDMA_RX_DCB_MAX_DBS, FDMA_TX_DCB_MAX_DBS, dcb_index and db_index with
the equivalents from the FDMA rx and tx structs. These variables are not
entangled in any buffer allocation and can therefore be replaced in
advance.
Signed-off-by: Daniel Machon <daniel.machon@microchip.com>
Reviewed-by: Steen Hegelund <Steen.Hegelund@microchip.com>
Reviewed-by: Jens Emil Schulz Østergaard <jensemil.schulzostergaard@microchip.com>
Reviewed-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This reverts commit bf4d87f884 because it
introduced dev_err_probe() in non-probe path, which is not desired.
In general, calling dev_err_probe() after successful probe in case of
handling -EPROBE_DEFER error, will set deferred status on the device
already probed. This is however not a problem here now, because
dev_err_probe() in affected places is used for handling errors from
request_firmware(), which does not return -EPROBE_DEFER. Still usage of
dev_err_probe() in such case is not correct, because request_firmware()
could once return -EPROBE_DEFER.
Fixes: bf4d87f884 ("net: alacritech: Switch to use dev_err_probe()")
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/20240902163610.17028-1-krzysztof.kozlowski@linaro.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
This update allows listing default firewalld ruleset on Fedora 40 via
tools/net/ynl/cli.py --spec \
Documentation/netlink/specs/nftables.yaml --dump getrule
Default ruleset uses fib, reject and objref expressions which were
missing.
Other missing expressions can be added later.
Improve decoding while at it:
- add bitwise, ct and lookup attributes
- wire up the quota expression
- translate raw verdict codes to a human reable name, e.g.
'code': 4294967293 becomes 'code': 'jump'.
v2: forgot fib addrtype in enum list (Donald Hunter)
Reviewed-by: Donald Hunter <donald.hunter@gmail.com>
Signed-off-by: Florian Westphal <fw@strlen.de>
Link: https://patch.msgid.link/20240902214112.2549-1-fw@strlen.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Matthieu Baerts says:
====================
mptcp: MIB counters for MPJ TX + misc improvements
Recently, a few issues have been discovered around the creation of
additional subflows. Without these counters, it was difficult to point
out the reason why some subflows were not created as expected.
In patch 3, all error paths from __mptcp_subflow_connect() are covered,
except the one related to the 'fully established mode', because it can
only happen with the userspace PM, which will propagate the error to the
userspace in this case (ENOTCONN).
These new counters are also verified in the MPTCP Join selftest in patch
6.
While at it, a few other patches are improving the MPTCP path-manager
code ...
- Patch 1: 'flush' related helpers are renamed to avoid confusions
- Patch 2: directly pass known ID and flags to create a new subflow,
i/o getting them later by iterating over all endpoints again
... and the MPJoin selftests:
- Patch 4: reduce the number of positional parameters
- Patch 5: only one line for the 'join' checks, instead of 3
- Patch 7: more explicit check names, instead of sometimes too cryptic
ones: rtx, ptx, ftx, ctx, fclzrx, sum
- Patch 8: specify client/server instead of 'invert' for some checks
not suggesting one specific direction
- Patch 9: mute errors of mptcp_connect when ran in the background
- Patch 10: simplify checksum_tests by using a for-loop
- Patch 11: remove 'define' re-definitions
====================
Link: https://patch.msgid.link/20240902-net-next-mptcp-mib-mpjtx-misc-v1-0-d3e0f3773b90@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Instead of displaying 'invert' when looking at some events like MP_FAIL,
MP_FASTCLOSE, MP_RESET, RM_ADDR, which is a bit vague because they are
not traditionnaly sent from one side, the host being checked is now
printed.
For the ADD_ADDR, only display the host when it is the client sending
it, which is more unusual.
Also before, the 'invert' message was printed after a few checks, but it
was not clear which ones exactly.
Reviewed-by: Geliang Tang <geliang@kernel.org>
Signed-off-by: Matthieu Baerts (NGI0) <matttbe@kernel.org>
Link: https://patch.msgid.link/20240902-net-next-mptcp-mib-mpjtx-misc-v1-8-d3e0f3773b90@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
A few new MPJoinSynTx MIB counters have been added in a previous commit.
They are being validated here in mptcp_join.sh selftest, each time the
number of received MPJ are checked.
Most of the time, the number of sent SYN+MPJ is the same as the received
ones. But sometimes, there are more, because there are dropped, or there
are errors.
While at it, the "no MPC reuse with single endpoint" subtest has been
modified to force a bind() error.
Reviewed-by: Geliang Tang <geliang@kernel.org>
Signed-off-by: Matthieu Baerts (NGI0) <matttbe@kernel.org>
Link: https://patch.msgid.link/20240902-net-next-mptcp-mib-mpjtx-misc-v1-6-d3e0f3773b90@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
chk_join_nr() currently takes 9 positional parameters, 6 of them are
optional. It makes it hard to read:
chk_join_nr 1 1 1 1 0 1 1 0 4
Naming these vars helps to make it easier to read:
join_csum_ns1=1 join_csum_ns2=0 \
join_fail_nr=1 join_rst_nr=1 join_infi_nr=0 \
join_corrupted_pkts=4 \
chk_join_nr 1 1 1
It will then be easier to add new optional parameters.
Reviewed-by: Geliang Tang <geliang@kernel.org>
Signed-off-by: Matthieu Baerts (NGI0) <matttbe@kernel.org>
Link: https://patch.msgid.link/20240902-net-next-mptcp-mib-mpjtx-misc-v1-4-d3e0f3773b90@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
__mptcp_subflow_connect() is currently called from the path-managers,
which have all the required information to create subflows. No need to
call the PM again to re-iterate over the list of entries with RCU lock
to get more info.
Instead, it is possible to pass a mptcp_pm_addr_entry structure, instead
of a mptcp_addr_info one. The former contains the ifindex and the flags
that are required when creating the new subflow.
This is a partial revert of commit ee285257a9 ("mptcp: drop flags and
ifindex arguments").
While at it, the local ID can also be set if it is known and 0, to avoid
having to set it in the 'rebuild_header' hook, which will cause a new
iteration of the endpoint entries.
Reviewed-by: Mat Martineau <martineau@kernel.org>
Signed-off-by: Matthieu Baerts (NGI0) <matttbe@kernel.org>
Link: https://patch.msgid.link/20240902-net-next-mptcp-mib-mpjtx-misc-v1-2-d3e0f3773b90@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Tony Nguyen says:
====================
Intel Wired LAN Driver Updates 2024-08-30 (igc, e1000e, i40e)
This series contains updates to igc, e1000e, and i40 drivers.
Kurt Kanzenbach adds support for MQPRIO offloads and stops unintended,
excess interrupts on igc.
Sasha adds reporting of EEE (Energy Efficient Ethernet) ability and
moves a register define to a better suited file for igc.
Vitaly stops reporting errors on shutdown and suspend as they are not
fatal for e1000e.
Alex adds reporting of EEE to i40e.
* '1GbE' of git://git.kernel.org/pub/scm/linux/kernel/git/tnguy/next-queue:
i40e: Add Energy Efficient Ethernet ability for X710 Base-T/KR/KX cards
e1000e: avoid failing the system during pm_suspend
igc: Move the MULTI GBT AN Control Register to _regs file
igc: Add Energy Efficient Ethernet ability
igc: Get rid of spurious interrupts
igc: Add MQPRIO offload support
====================
Link: https://patch.msgid.link/20240830210451.2375215-1-anthony.l.nguyen@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Stefan Schmidt says:
====================
pull-request: ieee802154 for net 2024-09-01
Simon Horman catched two typos in our headers. No functional change.
* tag 'ieee802154-for-net-2024-09-01' of git://git.kernel.org/pub/scm/linux/kernel/git/wpan/wpan:
ieee802154: Correct spelling in nl802154.h
mac802154: Correct spelling in mac802154.h
====================
Link: https://patch.msgid.link/20240901184213.2303047-1-stefan@datenfreihafen.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
This patch improves two checks on user data.
The first one prevents bit 23 from being set, as specified by RFC 9197
(Sec 4.4.1):
Bit 23 Reserved; MUST be set to zero upon transmission and be
ignored upon receipt. This bit is reserved to allow for
future extensions of the IOAM Trace-Type bit field.
The second one checks that the tunnel destination address !=
IPV6_ADDR_ANY, just like we already do for the tunnel source address.
Signed-off-by: Justin Iurman <justin.iurman@uliege.be>
Link: https://patch.msgid.link/20240830191919.51439-1-justin.iurman@uliege.be
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
These functions were never implenmented since introduction in
commit 8199d3a79c ("[PATCH] A new 10GB Ethernet Driver by Chelsio
Communications")
Signed-off-by: Yue Haibing <yuehaibing@huawei.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
