Since commit 63b0cd30b7 ("media: ov2680: Add bus-cfg / endpoint
property verification") the ov2680 no longer probes on a imx7s-warp7:
ov2680 1-0036: error -EINVAL: supported link freq 330000000 not found
ov2680 1-0036: probe with driver ov2680 failed with error -22
As the 'link-frequencies' property is not mandatory, allow the probe
to succeed by skipping the link-frequency verification when the
property is absent.
Cc: stable@vger.kernel.org
Fixes: 63b0cd30b7 ("media: ov2680: Add bus-cfg / endpoint property verification")
Signed-off-by: Fabio Estevam <festevam@denx.de>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Since commit 63b0cd30b7 ("media: ov2680: Add bus-cfg / endpoint
property verification") even when the correct 'link-frequencies'
property is passed in the devicetree, the driver fails to probe:
ov2680 1-0036: probe with driver ov2680 failed with error -22
The reason is that the variable 'ret' may contain the -EINVAL value
from a previous assignment:
ret = fwnode_property_read_u32(dev_fwnode(dev), "clock-frequency",
&rate);
Fix the problem by clearing 'ret' on the successful path.
Tested on imx7s-warp board with the following devicetree:
port {
ov2680_to_mipi: endpoint {
remote-endpoint = <&mipi_from_sensor>;
clock-lanes = <0>;
data-lanes = <1>;
link-frequencies = /bits/ 64 <330000000>;
};
};
Cc: stable@vger.kernel.org
Fixes: 63b0cd30b7 ("media: ov2680: Add bus-cfg / endpoint property verification")
Suggested-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Fabio Estevam <festevam@denx.de>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
The driver dug the supported link frequency up from the V4L2 fwnode
endpoint and used it internally, but failed to report this in the
LINK_FREQ and PIXEL_RATE controls. Fix this.
Fixes: 0677a2d9b7 ("media: ov2740: Add support for 180 MHz link frequency")
Cc: stable@vger.kernel.org # for v6.8 and later
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Bingbu Cao <bingbu.cao@intel.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
The notifier_entry of a notifier is not re-initialised after unregistering
the notifier. This leads to dangling pointers being left there so use
list_del_init() to return the notifier_entry an empty list.
Fixes: b8ec754ae4 ("media: v4l: async: Set v4l2_device and subdev in async notifier init")
Cc: <stable@vger.kernel.org> # for 6.6 and later
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
The V4L2 device used to be set when the notifier was registered but this
has been moved to the notifier initialisation. Don't touch the V4L2 device
if registration fails.
Fixes: b8ec754ae4 ("media: v4l: async: Set v4l2_device and subdev in async notifier init")
Cc: <stable@vger.kernel.org> # for 6.6 and later
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
struct v4l2_async_notifier has several list_head members, but only
waiting_list and done_list are initialized. notifier_entry was kept
'zeroed' leading to an uninitialized list_head.
This results in a NULL-pointer dereference if csi2_async_register() fails,
e.g. node for remote endpoint is disabled, and returns -ENOTCONN.
The following calls to v4l2_async_nf_unregister() results in a NULL
pointer dereference.
Add the missing list head initializer.
Fixes: b8ec754ae4 ("media: v4l: async: Set v4l2_device and subdev in async notifier init")
Cc: <stable@vger.kernel.org> # for 6.6 and later
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
To support compilation with Media controller disabled, drivers were
required to conditionally call media_device_init and media_device_cleanup.
Add nop implementations of both so drivers don't need to care (or at least
care less).
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Acked-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Call devm_request_irq() before registering the async notifier, as otherwise
it would be possible to use the device before the interrupts could be
delivered to the driver.
Fixes: c2a6a07afe ("media: intel-ipu3: cio2: add new MIPI-CSI2 driver")
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
After the conversion of dv timing calls to use a pad argument is done,
remove the old callbacks. Update the subdev ioctl handlers to use the
new callbacks.
Signed-off-by: Paweł Anikiel <panikiel@google.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Use the pad variant for all (s|g|query)_dv_timings subdev calls, which
includes a pad argument.
Signed-off-by: Paweł Anikiel <panikiel@google.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Use the pad variant for all (s|g|query)_dv_timings subdev calls, which
includes a pad argument.
Signed-off-by: Paweł Anikiel <panikiel@google.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Use the pad variant for all (s|g|query)_dv_timings subdev calls, which
includes a pad argument.
Signed-off-by: Paweł Anikiel <panikiel@google.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Use the pad variant for all (s|g|query)_dv_timings subdev calls, which
includes a pad argument.
Signed-off-by: Paweł Anikiel <panikiel@google.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Change all (s|g|query)_dv_timings subdev callbacks to include
a pad argument.
Signed-off-by: Paweł Anikiel <panikiel@google.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
[hverkuil: align to open parenthesis]
Change all (s|g|query)_dv_timings subdev callbacks to include
a pad argument.
Signed-off-by: Paweł Anikiel <panikiel@google.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
[hverkuil: align to open parenthesis]
Change all (s|g|query)_dv_timings subdev callbacks to include
a pad argument.
Signed-off-by: Paweł Anikiel <panikiel@google.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Change all (s|g|query)_dv_timings subdev callbacks to include
a pad argument.
Signed-off-by: Paweł Anikiel <panikiel@google.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
[hverkuil: align to open parenthesis]
Change all (s|g|query)_dv_timings subdev callbacks to include
a pad argument.
Signed-off-by: Paweł Anikiel <panikiel@google.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
[hverkuil: align to open parenthesis]
Change all (s|g|query)_dv_timings subdev callbacks to include
a pad argument.
Signed-off-by: Paweł Anikiel <panikiel@google.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
[hverkuil: align to open parenthesis]
Change all (s|g|query)_dv_timings subdev callbacks to include
a pad argument.
Signed-off-by: Paweł Anikiel <panikiel@google.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Change all (s|g|query)_dv_timings subdev callbacks to include
a pad argument.
Signed-off-by: Paweł Anikiel <panikiel@google.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
[hverkuil: align to open parenthesis]
Change all (s|g|query)_dv_timings subdev callbacks to include
a pad argument.
Signed-off-by: Paweł Anikiel <panikiel@google.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
[hverkuil: align to open parenthesis]
Currently, subdev dv timing calls (i.e. g/s/query_dv_timings) are video
ops without a pad argument. This is a problem if the subdevice can have
different dv timings for each pad (e.g. a DisplayPort receiver with
multiple virtual channels).
To solve this, change these calls to include a pad argument, and put
them into pad ops. Keep the old ones temporarily to make the switch
easier.
Signed-off-by: Paweł Anikiel <panikiel@google.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
vfe-170 and vfe-175 can be supported in the same file with some minimal
indirection to differentiate between the silicon versions.
sdm845 uses vfe-170, sc8280xp uses vfe-175-200. Lets rename the file to
capture its wider scope than vfe-170 only.
Acked-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
This commit describes the hardware layout for the sc8280xp for the
following hardware blocks:
- 4 x VFE, 4 RDI per VFE
- 4 x VFE Lite, 4 RDI per VFE
- 4 x CSID
- 4 x CSID Lite
- 4 x CSI PHY
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Acked-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Add a PHY configuration sequence for the sc8280xp which uses a Qualcomm
Gen 2 version 1.1 CSI-2 PHY.
The PHY can be configured as two phase or three phase in C-PHY or D-PHY
mode. This configuration supports two-phase D-PHY mode.
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
This driver's initialization functions do not perform any custom code,
except printing messages. Printing messages on modules
loading/unloading is discouraged because it pollutes the dmesg
regardless whether user actually has this device. Core kernel code
already gives tools to investigate whether module was loaded or not.
Drop the printing messages which allows to replace open-coded
module_sdio_driver().
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Because the size passed to copy_from_user() cannot be known beforehand,
it needs to be checked during runtime with check_object_size. That makes
gcc believe that the content of sbuf can be used before init.
Fix:
./include/linux/thread_info.h:215:17: warning: ‘sbuf’ may be used uninitialized [-Wmaybe-uninitialized]
Signed-off-by: Ricardo Ribalda <ribalda@chromium.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Increase the size of led_names so it can fit any valid v4l2 device name.
Fixes:
drivers/media/radio/radio-shark2.c:197:17: warning: ‘%s’ directive output may be truncated writing up to 35 bytes into a region of size 32 [-Wformat-truncation=]
Signed-off-by: Ricardo Ribalda <ribalda@chromium.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Make sure that tegra20_vi_get_input_formats always assign a value for
yuv_input_format.
Fix:
drivers/staging/media/tegra-video/tegra20.c:624:72: warning: ‘yuv_input_format’ may be used uninitialized [-Wmaybe-uninitialized]
Signed-off-by: Ricardo Ribalda <ribalda@chromium.org>
Reviewed-by: Luca Ceresoli <luca.ceresoli@bootlin.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
clang-19 warns about mixing two enum types here:
drivers/media/platform/renesas/rcar-vin/rcar-vin.h:296:12: error: conditional expression between different enumeration types ('enum rvin_csi_id' and 'enum rvin_isp_id') [-Werror,-Wenum-compare-conditional]
drivers/media/platform/renesas/rcar-vin/rcar-core.c:216:18: error: conditional expression between different enumeration types ('enum rvin_csi_id' and 'enum rvin_isp_id') [-Werror,-Wenum-compare-conditional]
drivers/media/platform/renesas/rcar-vin/rcar-vin.h:296:12: error: conditional expression between different enumeration types ('enum rvin_csi_id' and 'enum rvin_isp_id') [-Werror,-Wenum-compare-conditional]
drivers/media/platform/renesas/rcar-vin/rcar-vin.h:296:12: error: conditional expression between different enumeration types ('enum rvin_csi_id' and 'enum rvin_isp_id') [-Werror,-Wenum-compare-conditional]
This one is intentional, and there is already a cast to work around another
warning, so address this by adding another cast.
Fixes: 406bb586de ("media: rcar-vin: Add r8a779a0 support")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Fix the mgb4 driver documentation structure that breaks the
"Video4Linux (V4L) driver-specific documentation" outline.
Signed-off-by: Martin Tůma <martin.tuma@digiteqautomotive.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
The v4l2_buffer type has an "offset" field, but the corresponding field
in the v4l2_plane type is called "mem_offset". Use the correct name in
this example.
Signed-off-by: Matthijs Kooijman <matthijs@stdin.nl>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
According to the formats description in videodev2.h Y210, Y212 and Y216
are YCbCr packed formats. For each Y2xx format, xx bits of valid data
occupy the MSBs of the 16 bit components, and 16-xx bits of zero padding
occupy the LSBs.
The Y210 and Y216 formats are missing an entry in the v4l2_format_info[]
table. Add it.
Signed-off-by: Jacopo Mondi <jacopo.mondi@ideasonboard.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Add terminating new line to the Kconfig file.
Signed-off-by: Prasad Pandit <pjp@fedoraproject.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
[hverkuil: dropped 'Fixes' tag, not relevant for this]
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is ignored (apart
from emitting a warning) and this typically results in resource leaks.
To improve here there is a quest to make the remove callback return
void. In the first step of this quest all drivers are converted to
.remove_new(), which already returns void. Eventually after all drivers
are converted, .remove_new() will be renamed to .remove().
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Changhuang Liang <changhuang.liang@starfivetech.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
A 'case V4L2_CTRL_TYPE_AREA' was missing in v4l2_ctrl_type_op_log,
which led to an 'unknown type' message in the kernel log.
Add support for controls of this type.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
The return value of dvb_ca_en50221_init() is not checked here that may
cause undefined behavior in case of nonzero value return.
Found by Linux Verification Center (linuxtesting.org) with SVACE.
Fixes: 25aee3debe ("[media] Rename media/dvb as media/pci")
Signed-off-by: Aleksandr Burakov <a.burakov@rosalinux.ru>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
anysee_master_xfer currently accepts read messages of length 2 only.
However, several frontends, e.g. tda10023 send buffers of length 1,
containing an 8-bit register number (see tda10023_readreg).
These buffers are rejected currently, making many Anysee variants
to not work. In these cases the "Unsupported Anysee version"
message is logged.
This patch alters the function to accept buffers of a length of 1 too.
Signed-off-by: István Váradi <ivaradi@varadiistvan.hu>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
[hverkuil: add spaces around '<', fix typo in 'sevaral']
Linux 6.9-rc2
This is needed to pull in commit 11763a8598 ("fs/9p: fix uaf in
in v9fs_stat2inode_dotl"), which fixes the broken virtme. With this
fix the media regression tests can be run again without crashing.
Pull Kbuild fixes from Masahiro Yamada:
- Deduplicate Kconfig entries for CONFIG_CXL_PMU
- Fix unselectable choice entry in MIPS Kconfig, and forbid this
structure
- Remove unused include/asm-generic/export.h
- Fix a NULL pointer dereference bug in modpost
- Enable -Woverride-init warning consistently with W=1
- Drop KCSAN flags from *.mod.c files
* tag 'kbuild-fixes-v6.9' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild:
kconfig: Fix typo HEIGTH to HEIGHT
Documentation/llvm: Note s390 LLVM=1 support with LLVM 18.1.0 and newer
kbuild: Disable KCSAN for autogenerated *.mod.c intermediaries
kbuild: make -Woverride-init warnings more consistent
modpost: do not make find_tosym() return NULL
export.h: remove include/asm-generic/export.h
kconfig: do not reparent the menu inside a choice block
MIPS: move unselectable FIT_IMAGE_FDT_EPM5 out of the "System type" choice
cxl: remove CONFIG_CXL_PMU entry in drivers/cxl/Kconfig
