Enable USB0 on the EA4357 devkit and setup the required USB0
control pins.
Signed-off-by: Joachim Eastwood <manabian@gmail.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
All devices in the LPC18xx/43xx familiy contain a ARM PL172
MultiPort Memory Controller (MPMC).
Signed-off-by: Joachim Eastwood <manabian@gmail.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
NXP LPC185x and LPC435x/70 devices contain a ARM PL111 lcd controller.
Signed-off-by: Joachim Eastwood <joachim.eastwood@gmail.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
Add the USB OTG phy under the CREG syscon node and attach it to
the USB0 EHCI controller.
Signed-off-by: Joachim Eastwood <manabian@gmail.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
Qualcomm ARM Based Device Tree Updates for v4.3
* Switch to use pinctrl compatible for GPIOs
* Add RPM regulators for MSM8960
* Add SPI Ethernet support on MSM8960 CDP
* Add SMEM support along with dependencies
* Add PM8921 support for GPIO and MPP
* Fix GSBI cell index
* Switch to use real regulators on APQ8064 w/ SDCC
* tag 'qcom-dt-for-4.3' of git://codeaurora.org/quic/kernel/agross-msm:
ARM: dts: qs600: Add real regulators to sdcc
ARM: dts: ifc6410: add real regulators for sdcc nodes.
ARM: dts: apq8064: remove temporary fixed regulator for mmc
ARM: dts: apq8064: fix missing gsbi cell-index
ARM: dts: apq8064: Add DT support for GSBI6 and for UART pin mux
ARM: dts: apq8064: add pm8921 mpp support
ARM: dts: apq8064: Add pm8921 mfd and its gpio node
ARM: dts: msm8974: Add smem reservation and node
ARM: dts: msm8974: Add tcsr mutex node
ARM: dts: qcom: Add ks8851 node for wired ethernet
ARM: dts: qcom: Add MSM8960 CDP RPM regulators
ARM: dts: qcom: Add MSM8960 RPM and RPM regulator nodes
ARM: dts: qcom: Replace gpio node with pinctrl node
ARM: dts: qcom: Replace gpio node with pinctrl node
Signed-off-by: Olof Johansson <olof@lixom.net>
Adds the two MIO connected pushbuttons on the zc702 board to the devicetree as a
single multi-key device for us with the gpio-keys driver.
Signed-off-by: Ezra Savard <ezra.savard@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Add OCM node for all zynq boards. OCM location
can changed but for all current boards this
is the location where OCM is.`
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Add minimal support for the new sama5d2 Xplained board. Only USB,
spi/i2c, ethernet and uart/usart peripherals added.
With this DTS file you can boot the board and begin to play with it.
Rootfs on NFS and sd card have successfully been tested.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Only the basic support for this new Atmel Cortex-A5 SoC. A subset of the
peripherals is setup to allow booting.
IRQ, clocks, USB, crypto, timers, rtc, ethernet, spi/i2c and
uart/usart peripheral nodes are added.
Signed-off-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Acked-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
They'll use "atmel,sama5d3-rstc" for reset function.
Signed-off-by: Josh Wu <josh.wu@atmel.com>
Acked-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
[nicolas.ferre@atmel.com: add the old compatible string as a fallback]
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
First we group the isi data pins, and for now we only use 0~7 data pins
with HSYNC and VSYNC.
Also add the link for atmel-isi and ov2640 sensor node.
Signed-off-by: Josh Wu <josh.wu@atmel.com>
[nicolas.ferre@atmel.com: move the pinctrl properties in board .dts file]
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
This patch removes temporary fixed regluator use for mmc.
Board files should use the regulators which are wiredup appropriately.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Andy Gross <agross@codeaurora.org>
SoCFPGA DTS updates for v4.3
- Update clocking for DTS nodes
- Add DTS board file for Terasic DE0 Atlas board
- Use stdout-patch for chosen node
- Enable prefetch-data and prefetch-instr
* tag 'socfpga_dts_for_v4.3' of git://git.kernel.org/pub/scm/linux/kernel/git/dinguyen/linux:
ARM: socfpga: dts: add osc1 as a possible parent for dbg_base_clk
ARM: socfpga: dts: add missing clock gates to socfpga.dtsi
ARM: socfpga: dts: Fix gpio dts entry for the correct clock
ARM: socfpga: dts: Correct the parent clock for l3_sp_clk and dbg_clk
ARM: dts: socfpga: Add support of Terasic DE0 Atlas board
ARM: dts: socfpga: use stdout-path for chosen node
ARM: dts: socfpga: enable the data and instruction prefetch for the l2 cache
Signed-off-by: Olof Johansson <olof@lixom.net>
Without this i2c instance for missing cell-index nodes would fail, fix
it by adding correct cell-index.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Andy Gross <agross@codeaurora.org>
This change adds DT support for GSBI6 and muxes the gpio pins
as UART lines. Also defines a alias for serial port on these lines.
Signed-off-by: Pramod Gurav <pramod.gurav@smartplayin.com>
[Srinivas Kandagatla]: fix pinctrl location and rename alias correctly
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Andy Gross <agross@codeaurora.org>
This patch adds pmic gpio node to the device tree, this node is
necessary for devices like wlan to control reset gpio.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Andy Gross <agross@codeaurora.org>
The DT nodes in uniphier-pinctrl.dtsi provide the default pinctrl
settings that would be suitable for most boards. You can still
override them in your board DTS file if necessary.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
Add the pinctrol device nodes for UniPhier PH1-LD4, PH1-Pro4,
and PH1-sLD8.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
omap dts changes for minimal dm814x support for v4.3 merge window.
These changes make dm814x boot and adds minimal board support for
dm814x-evm and hp t410.
Note that to boot these depend on omap-for-v4.3/soc-signed branch,
but as dm814x support is currently broken, these can be merged
separately with the other dts changes.
* tag 'omap-for-v4.3/dt-dm814x' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: OMAP2+: Add custom abort handler for t410
ARM: dts: Add minimal support for HP T410
ARM: dts: Add minimal dts support for dm8148-evm
ARM: dts: Add minimal clocks for dm814x
ARM: dts: Add minimal dm814x support
Signed-off-by: Olof Johansson <olof@lixom.net>
Second Round of Renesas ARM Based SoC DT Updates for v4.3
* Add Audio MIX and CTU support to r8a779[01] SoCs
* Correct IRQ sense for adv7511 on lager board
* Add sound label to koelsch and lager boards
* Add IIC support to emev2 SoC
* tag 'renesas-dt2-for-v4.3' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas:
ARM: shmobile: r8a7791: Add Audio MIX support on DTSI
ARM: shmobile: r8a7791: Add Audio CTU support on DTSI
ARM: shmobile: r8a7790: Add Audio MIX support on DTSI
ARM: shmobile: r8a7790: Add Audio CTU support on DTSI
ARM: shmobile: lager: Fix adv7511 IRQ sensing
ARM: shmobile: koelsch: add sound label on DTS
ARM: shmobile: lager: add sound label on DTS
ARM: shmobile: emev2: kzm9d: enable IIC busses
ARM: shmobile: emev2: add IIC cores to dtsi
Signed-off-by: Olof Johansson <olof@lixom.net>
STM32 DT updates for v4.3, round 1.
Highlights:
-----------
- Add RCC clocks support to STM32F429
- Add STM32429i-EVAL board support
- Use stdout-path instead of linux,stdout-path in Disco board
* tag 'stm32-dt-for-v4.3-1b' of https://git.kernel.org/pub/scm/linux/kernel/git/mcoquelin/stm32:
ARM: dts: Use stdout-path in STM32F429 Discovery board
ARM: dts: Add STM32429i-EVAL board support
ARM: dts: stm32f429: Adopt STM32F4 clock driver
Signed-off-by: Olof Johansson <olof@lixom.net>
Similar to commit fdf4850cb5 ("ARM: BCM5301X: workaround suppress fault"),
let's add custom handling for the aborts on t410 that prevent booting:
Unhandled fault: imprecise external abort (0xc06) at 0xee091fb0
pgd = ee4bc000
[ee091fb0] *pgd=ae00041e(bad)
Kernel panic - not syncing: Attempted to kill init! exitcode=0x00000007
Cc: Matthijs van Duin <matthijsvanduin@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Use fixed clocks until we have a clock driver for the PLL.
The mux and divider composite clocks work the same way
as on dm816x and am335x.
Cc: Matthijs van Duin <matthijsvanduin@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The micrel ks8851 device is present on MSM8960 CDP boards. It is
connected to two regulators, one controlled via a gpio and
another controlled via the RPM. Add the gsbi, spi, gpio
regulator, and micrel ks8851 nodes so that ethernet works
properly.
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Andy Gross <agross@codeaurora.org>
Add RPM regulators and configure their constraints on the MSM8960
CDP so that we can control these supplies.
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Andy Gross <agross@codeaurora.org>
Add the basic RPM and RPM regulator nodes that boards can fill in
with their board specific details.
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Andy Gross <agross@codeaurora.org>
Now that we have a proper pinctrl driver for the gpio block we
can change the compatible field here and configure the pinmux on
msm8960 devices.
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Andy Gross <agross@codeaurora.org>
This patch replaces use of linux,stdout-path by stdout-path as per
"chosen" DT bindings documentation.
Doing that, the "console" argument is no more needed in kernel command
line.
Reported-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Maxime Coquelin <mcoquelin.stm32@gmail.com>
Merge "omap dts changes for v4.3, part2" from Tony Lindgren:
More omap dts changes for v4.3 merge window:
- Add missing devices for pandora. Note that we're adding wl1251
WLAN and LCD backlight support for now using legacy pdata as that
allows us to drop the legacy board file for pandora in another
series of patches
- Enable power button support for omap5-uevm
- Add aliases for am437x UARTs
- Add support for phyCORE phyBOARD-WEGA-AM335x rdk and
phyCORE-AM335x SoM
- Use u16 values for tsc2046 on omap3-lilly
* tag 'omap-for-v4.3/dt-pt2' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: OMAP2+: omap3-pandora: add wifi support
ARM: OMAP2+: omap3-pandora: add backlight support
ARM: dts: omap3-pandora: add support for usb host and 32k buffer
ARM: dts: omap3-pandora: miscellaneous corrections
ARM: dts: omap5-uevm: Add Palmas power button support
ARM: dts: am437x: add aliases for all UART instances
ARM: dts: Add phyBOARD-WEGA-AM335x rdk
ARM: dts: Add support for phyCORE-AM335x SoM
ARM: dts: omap3: correct the format of u16 values for tsc2046 node
Signed-off-by: Olof Johansson <olof@lixom.net>
