In atmel_conf_pin_config_dbg_show(), checking atmel_pioctrl->pins[pin_id]
against being NULL doesn't make any sense as it gets derefenced first and
the driver's probe() method immediately returns -ENOMEM when devm_kzalloc()
returns NULL for any atmel_pioctrl->pins[] element anyway, thus failing to
register the device...
Found by Linux Verification Center (linuxtesting.org) with the Svace static
analysis tool.
Signed-off-by: Sergey Shtylyov <s.shtylyov@omp.ru>
Link: https://lore.kernel.org/r/4ab2f59f-45c1-76a2-94da-3331e8ec4e35@omp.ru
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Update binding for yaml and remove the old related txt bindings. Note that
we are also adding the undocumented pinctrl-single,slew-rate property. And
we only use the first example from the old binding.
As we are mostly using a generic compatible across various SoCs, let's not
start adding matches for random pin group node naming. Let's standardize on
pin group node name ending in -pins with an optional instance number
suffix.
As a pin group may have additional pins added to it later on, let's always
use -pins rather than -pin for the gropu name.
Most of the dts files have been updated already for the pin group node
names with a few changes still pending.
Cc: Nishanth Menon <nm@ti.com>
Cc: Vignesh Raghavendra <vigneshr@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20230721082654.27036-1-tony@atomide.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Add support to handle 'output-enable' and 'bias-high-impedance'
configurations.
Using these pinctrl properties observed hang issues with older PMUFW(Xilinx
ZynqMP Platform Management Firmware), hence reverted the patch.
Commit 9989bc33c4 ("Revert "pinctrl: pinctrl-zynqmp: Add support
for output-enable and bias-high-impedance"").
Support for configuring these properties added in PMUFW Configuration Set
version 2.0. When there is a request for these configurations from pinctrl
driver for ZynqMP platform, xilinx firmware driver checks for this version
before configuring these properties to avoid the hang issue and proceeds
further only when firmware version is >=2 otherwise it returns error.
Signed-off-by: Sai Krishna Potthuri <sai.krishna.potthuri@amd.com>
Reviewed-by: Michal Simek <michal.simek@amd.com>
Link: https://lore.kernel.org/r/20230731095026.3766675-5-sai.krishna.potthuri@amd.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Add 'output-enable' configuration parameter to the properties list.
Using these pinctrl properties observed hang issues with older Xilinx
ZynqMP Platform Management Firmware, hence reverted the patch previously.
Commit ff8356060e ("Revert "dt-bindings: pinctrl-zynqmp: Add
output-enable configuration"").
Support for configuring these properties added in Xilinx ZynqMP Platform
Management firmware(PMUFW) Configuration Set version 2.0. Linux firmware
driver checks if the configuration is supported by the PMUFW when it gets
request for TRISTATE configuration from pinctrl driver. If it supports,
then calls will be made otherwise it returns error.
Signed-off-by: Sai Krishna Potthuri <sai.krishna.potthuri@amd.com>
Acked-by: Conor Dooley <conor.dooley@microchip.com>
Link: https://lore.kernel.org/r/20230731095026.3766675-4-sai.krishna.potthuri@amd.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
pinctrl_generic_add_function() doesn't check result of radix_tree_insert()
despite they both may return a negative error code. Linus Walleij said he
has copied the radix tree code from kernel/irq/ where the functions calling
radix_tree_insert() are *void* themselves; I think it makes more sense to
propagate the errors from radix_tree_insert() upstream if we can do that...
Found by Linux Verification Center (linuxtesting.org) with the Svace static
analysis tool.
Signed-off-by: Sergey Shtylyov <s.shtylyov@omp.ru>
Link: https://lore.kernel.org/r/20230719202253.13469-4-s.shtylyov@omp.ru
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
pinctrl_register_one_pin() doesn't check the result of radix_tree_insert()
despite they both may return a negative error code. Linus Walleij said he
has copied the radix tree code from kernel/irq/ where the functions calling
radix_tree_insert() are *void* themselves; I think it makes more sense to
propagate the errors from radix_tree_insert() upstream if we can do that...
Found by Linux Verification Center (linuxtesting.org) with the Svace static
analysis tool.
Signed-off-by: Sergey Shtylyov <s.shtylyov@omp.ru>
Link: https://lore.kernel.org/r/20230719202253.13469-3-s.shtylyov@omp.ru
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
pinctrl_generic_add_group() doesn't check the result of radix_tree_insert()
despite they both may return a negative error code. Linus Walleij said he
has copied the radix tree code from kernel/irq/ where the functions calling
radix_tree_insert() are *void* themselves; I think it makes more sense to
propagate the errors from radix_tree_insert() upstream if we can do that...
Found by Linux Verification Center (linuxtesting.org) with the Svace static
analysis tool.
Signed-off-by: Sergey Shtylyov <s.shtylyov@omp.ru>
Link: https://lore.kernel.org/r/20230719202253.13469-2-s.shtylyov@omp.ru
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The DT of_device.h and of_platform.h date back to the separate
of_platform_bus_type before it as merged into the regular platform bus.
As part of that merge prepping Arm DT support 13 years ago, they
"temporarily" include each other. They also include platform_device.h
and of.h. As a result, there's a pretty much random mix of those include
files used throughout the tree. In order to detangle these headers and
replace the implicit includes with struct declarations, users need to
explicitly include the correct includes.
Signed-off-by: Rob Herring <robh@kernel.org>
Reviewed-by: Damien Le Moal <dlemoal@kernel.org>
Acked-by: Emil Renner Berthing <emil.renner.berthing@canonical.com>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20230714174901.4062397-1-robh@kernel.org
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The sunxi pinctrl has a fixed size array it uses to store regulators used
in the driver. There is currently nothing that ensures that the number of
elements in the array is large enough to map the regulators defined by the
individual SoCs. While this is currently the case having an explicit check
in there will make life easier for anyone debugging memory issues that
manifest in the driver so let's add one.
Signed-off-by: Mark Brown <broonie@kernel.org>
Reviewed-by: Chen-Yu Tsai <wens@csie.org>
Reviewed-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Link: https://lore.kernel.org/r/20230712-pinctrl-sunxi-boudns-v1-1-85f37de79b9f@kernel.org
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This patch adds support for an optional "reset" GPIO pin in the cy8c95x0
pinctrl driver. On probe, the reset pin is pulled low to bring chip out
of reset. The reset pin has an internal pull-down and can be left
floating if not required.
The datasheet doesn't mention any timing related to the reset pin.
Based on empirical tests, it was found that the chip requires a
delay of 250 milliseconds before accepting I2C transfers after driving
the reset pin low. Therefore, a delay of 250ms is added before
proceeding with I2C transfers.
Signed-off-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Signed-off-by: Naresh Solanki <Naresh.Solanki@9elements.com>
Link: https://lore.kernel.org/r/20230714081902.2621771-2-Naresh.Solanki@9elements.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Currently, sd1 and sd0 have unique subnode names 'sd1_mux' and 'sd0_mux'.
If we change these to non-unique subnode names such as 'mux' this can
lead to the below conflict as the RZ/G2L pin control driver considers
only the names of the subnodes.
pinctrl-rzg2l 11030000.pinctrl: pin P47_0 already requested by 11c00000.mmc; cannot claim for 11c10000.mmc
pinctrl-rzg2l 11030000.pinctrl: pin-376 (11c10000.mmc) status -22
pinctrl-rzg2l 11030000.pinctrl: could not request pin 376 (P47_0) from group mux on device pinctrl-rzg2l
renesas_sdhi_internal_dmac 11c10000.mmc: Error applying setting, reverse things back
Fix this by constructing unique names from the node names of both the
pin control configuration node and its child node, where appropriate.
Based on the work done by Geert for the RZ/V2M pinctrl driver.
Fixes: c4c4637eb5 ("pinctrl: renesas: Add RZ/G2L pin and gpio controller driver")
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20230704111858.215278-1-biju.das.jz@bp.renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
The eMMC and SDHI pin control configuration nodes in DT have subnodes
with the same names ("data" and "ctrl"). As the RZ/V2M pin control
driver considers only the names of the subnodes, this leads to
conflicts:
pinctrl-rzv2m b6250000.pinctrl: pin P8_2 already requested by 85000000.mmc; cannot claim for 85020000.mmc
pinctrl-rzv2m b6250000.pinctrl: pin-130 (85020000.mmc) status -22
renesas_sdhi_internal_dmac 85020000.mmc: Error applying setting, reverse things back
Fix this by constructing unique names from the node names of both the
pin control configuration node and its child node, where appropriate.
Reported by: Fabrizio Castro <fabrizio.castro.jz@renesas.com>
Fixes: 92a9b82525 ("pinctrl: renesas: Add RZ/V2M pin and gpio controller driver")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Tested-by: Fabrizio Castro <fabrizio.castro.jz@renesas.com>
Link: https://lore.kernel.org/r/607bd6ab4905b0b1b119a06ef953fa1184505777.1688396717.git.geert+renesas@glider.be
We just sorted the entries and fields last release, so just out of a
perverse sense of curiosity, I decided to see if we can keep things
ordered for even just one release.
The answer is "No. No we cannot".
I suggest that all kernel developers will need weekly training sessions,
involving a lot of Big Bird and Sesame Street. And at the yearly
maintainer summit, we will all sing the alphabet song together.
I doubt I will keep doing this. At some point "perverse sense of
curiosity" turns into just a cold dark place filled with sadness and
despair.
Repeats: 80e62bc848 ("MAINTAINERS: re-sort all entries and fields")
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Pull dma-mapping fixes from Christoph Hellwig:
- swiotlb area sizing fixes (Petr Tesarik)
* tag 'dma-mapping-6.5-2023-07-09' of git://git.infradead.org/users/hch/dma-mapping:
swiotlb: reduce the number of areas to match actual memory pool size
swiotlb: always set the number of areas before allocating the pool
Pull irq update from Borislav Petkov:
- Optimize IRQ domain's name assignment
* tag 'irq_urgent_for_v6.5_rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
irqdomain: Use return value of strreplace()
Pull x86 fpu fix from Borislav Petkov:
- Do FPU AP initialization on Xen PV too which got missed by the recent
boot reordering work
* tag 'x86_urgent_for_v6.5_rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/xen: Fix secondary processors' FPU initialization
Pull x86 fix from Thomas Gleixner:
"A single fix for the mechanism to park CPUs with an INIT IPI.
On shutdown or kexec, the kernel tries to park the non-boot CPUs with
an INIT IPI. But the same code path is also used by the crash utility.
If the CPU which panics is not the boot CPU then it sends an INIT IPI
to the boot CPU which resets the machine.
Prevent this by validating that the CPU which runs the stop mechanism
is the boot CPU. If not, leave the other CPUs in HLT"
* tag 'x86-core-2023-07-09' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/smp: Don't send INIT to boot CPU
Pull MIPS fixes from Thomas Bogendoerfer:
- fixes for KVM
- fix for loongson build and cpu probing
- DT fixes
* tag 'mips_6.5_1' of git://git.kernel.org/pub/scm/linux/kernel/git/mips/linux:
MIPS: kvm: Fix build error with KVM_MIPS_DEBUG_COP0_COUNTERS enabled
MIPS: dts: add missing space before {
MIPS: Loongson: Fix build error when make modules_install
MIPS: KVM: Fix NULL pointer dereference
MIPS: Loongson: Fix cpu_probe_loongson() again
