To keep high sensitivity reaction, Bluetooth gaming controller will send
packet very frequently, it will make WLAN performance very poor. To solve
this situation, MIMO PS mechanism makes WLAN/BT own an antenna itself, WLAN
quits 2SS performance but it can get a stable 1SS performance and Bluetooth
gaming controller can keep sensitivity reaction at the same time.
Signed-off-by: Ching-Te Ku <ku920601@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220215004855.4098-5-pkshih@realtek.com
Split 6G band into 8 sub-bands where indexes are from 0 to 7,
i.e. RTW89_CH_6G_BAND_IDX[0-7]. Then, decide subband by both
band and channel instead of just channel because conflicts
between 5G channels and 6G channels.
Moreover, add default case to the existing use of switch (subband).
Signed-off-by: Zong-Zhe Yang <kevin_yang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220211075953.40421-4-pkshih@realtek.com
wireless-next patches for v5.18
First set of patches for v5.18, with both wireless and stack patches.
rtw89 now has AP mode support and wcn36xx has survey support. But
otherwise pretty normal.
Major changes:
ath11k
* add LDPC FEC type in 802.11 radiotap header
* enable RX PPDU stats in monitor co-exist mode
wcn36xx
* implement survey reporting
brcmfmac
* add CYW43570 PCIE device
rtw88
* rtw8821c: enable RFE 6 devices
rtw89
* AP mode support
mt76
* mt7916 support
* background radar detection support
Eric Dumazet says:
====================
ipv6: remove addrconf reliance on loopback
Second patch in this series removes IPv6 requirement about the netns
loopback device being the last device being dismantled.
This was needed because rt6_uncached_list_flush_dev()
and ip6_dst_ifdown() had to switch dst dev to a known
device (loopback).
Instead of loopback, we can use the (hidden) blackhole_netdev
which is also always there.
This will allow future simplfications of netdev_run_to()
and other parts of the stack like default_device_exit_batch().
Last two patches are optimizations for both IP families.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
This is an optimization to keep the per-cpu lists as short as possible:
Whenever rt_flush_dev() changes one rtable dst.dev
matching the disappearing device, it can can transfer the object
to a quarantine list, waiting for a final rt_del_uncached_list().
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is an optimization to keep the per-cpu lists as short as possible:
Whenever rt6_uncached_list_flush_dev() changes one rt6_info
matching the disappearing device, it can can transfer the object
to a quarantine list, waiting for a final rt6_uncached_list_del().
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
IPv6 addrconf notifiers wants the loopback device to
be the last device being dismantled at netns deletion.
This caused many limitations and work arounds.
Back in linux-5.3, Mahesh added a per host blackhole_netdev
that can be used whenever we need to make sure objects no longer
refer to a disappearing device.
If we attach to blackhole_netdev an ip6_ptr (allocate an idev),
then we can use this special device (which is never freed)
in place of the loopback_dev (which can be freed).
This will permit improvements in netdev_run_todo() and other parts
of the stack where had steps to make sure loopback_dev was
the last device to disappear.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Mahesh Bandewar <maheshb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This counter has never been visible, there is little point
trying to maintain it.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The mv88e6352, mv88e6240 and mv88e6176 have a serdes interface. This patch
allows to configure the output swing to a desired value in the
phy-handle of the port. The value which is peak to peak has to be
specified in microvolts. As the chips only supports eight dedicated
values we return EINVAL if the value in the DTS does not match one of
these values.
Signed-off-by: Holger Brunck <holger.brunck@hitachienergy.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Marek Behún <kabel@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Common PHYs and network PCSes often have the possibility to specify
peak-to-peak voltage on the differential pair - the default voltage
sometimes needs to be changed for a particular board.
Add properties `tx-p2p-microvolt` and `tx-p2p-microvolt-names` for this
purpose. The second property is needed to specify the mode for the
corresponding voltage in the `tx-p2p-microvolt` property, if the voltage
is to be used only for speficic mode. More voltage-mode pairs can be
specified.
Example usage with only one voltage (it will be used for all supported
PHY modes, the `tx-p2p-microvolt-names` property is not needed in this
case):
tx-p2p-microvolt = <915000>;
Example usage with voltages for multiple modes:
tx-p2p-microvolt = <915000>, <1100000>, <1200000>;
tx-p2p-microvolt-names = "2500base-x", "usb", "pcie";
Add these properties into a separate file phy/transmit-amplitude.yaml,
which should be referenced by any binding that uses it.
Signed-off-by: Marek Behún <kabel@kernel.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ->rtm_tos option is normally used to route packets based on both
the destination address and the DS field. However it's ignored for
IPv6 routes. Setting ->rtm_tos for IPv6 is thus invalid as the route
is going to work only on the destination address anyway, so it won't
behave as specified.
Suggested-by: Toke Høiland-Jørgensen <toke@redhat.com>
Signed-off-by: Guillaume Nault <gnault@redhat.com>
Reviewed-by: David Ahern <dsahern@kernel.org>
Reviewed-by: Shuah Khan <skhan@linuxfoundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Vladimir Oltean says:
====================
More aggressive DSA cleanup
This series deletes some code which is apparently not needed.
I've had these patches in my tree for a while, and testing on my boards
didn't reveal any issues.
Compared to the RFC v1 series, the only change is the addition of patch 3.
https://patchwork.kernel.org/project/netdevbpf/cover/20220107184842.550334-1-vladimir.oltean@nxp.com/
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Since commit 2f1e8ea726 ("net: dsa: link interfaces with the DSA
master to get rid of lockdep warnings"), suggested by Cong Wang, the
DSA interfaces and their master have different dev->nested_level, which
makes netif_addr_lock() stop complaining about potentially recursive
locking on the same lock class.
So we no longer need DSA slave interfaces to have their own lockdep
class.
Cc: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since commit 2f1e8ea726 ("net: dsa: link interfaces with the DSA
master to get rid of lockdep warnings"), suggested by Cong Wang, the
DSA interfaces and their master have different dev->nested_level, which
makes netif_addr_lock() stop complaining about potentially recursive
locking on the same lock class.
So we no longer need DSA masters to have their own lockdep class.
Cc: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are no legacy ports, DSA registers a devlink instance with ports
unconditionally for all switch drivers. Therefore, delete the old-style
ndo operations used for determining bridge forwarding domains.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Tested-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Ido Schimmel <idosch@nvidia.com>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
