Most AXPxxx-based reference designs place a 10k NTC thermistor on a
TS pin. When appropriately configured, AXP PMICs will inject fixed
current (80uA by default) into TS pin and measure the voltage across a
thermistor. The PMIC itself will by default compare this voltage with
predefined thresholds and disable battery charging whenever
the battery is too hot or too cold.
Alternatively, the TS pin can be configured as general-purpose
ADC input. This mode is not supported by the driver.
This patch allows reading the voltage on the TS pin. It can be then
either processed by userspace or used by kernel consumer like hwmon
ntc thermistor driver.
Signed-off-by: Evgeny Boger <boger@wirenboard.com>
Acked-by: Maxime Ripard <maxime@cerno.tech>
Reviewed-by: Quentin Schulz <foss+kernel@0leil.net>
Link: https://lore.kernel.org/r/20211118141233.247907-2-boger@wirenboard.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Introduce the capability to disable sensorhub through a device-tree
property since there are some configurations where users want to
explicitly disable sensor-hub auto-probing at bootstrap.
A typical configuration is when the sensorhub clock/data lines are connected
to a pull-up resistor since no slave sensors are connected to the i2c master.
If SDO/SA0 line is connected to the same pull-up resistor, when the driver
tries to probe slave devices connected on sensor-hub, it will force SDO/SA0
line to low, modifying the device i2c address.
Tested-by: Mario Tesi <mario.tesi@st.com>
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Link: https://lore.kernel.org/r/ad7894e7b1c6fb3427fab3f623bb942860ad45cf.1636816719.git.lorenzo@kernel.org
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The shared parameter should be configurable based on its usage, and not
constrained to IIO_SHARED_BY_TYPE.
This patch aims to improve the flexibility in using the
IIO_ENUM_AVAILABLE define and avoid redefining custom iio enums that
expose the shared parameter.
An example is the ad5766.c driver where IIO_ENUM_AVAILABLE_SHARED was
defined in order to achieve `shared` parameter customization.
The current state of the IIO_ENUM_AVAILABLE implementation will imply
similar redefinitions each time a driver will require access to the
`shared` parameter. An example would be admv1013 driver which will
require custom device attribute for the frequency translation modes:
Quadrature I/Q mode and Intermediate Frequency mode.
Signed-off-by: Antoniu Miclaus <antoniu.miclaus@analog.com>
Reviewed-by: Alexandru Ardelean <ardeleanalex@gmail.com>
Link: https://lore.kernel.org/r/20211119085627.6348-1-antoniu.miclaus@analog.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Using `dev_get_drvdata()` in IIO sysfs callbacks to get a pointer to the
IIO device is a relic from the very early days of IIO. The IIO core as well
as most other drivers have switched over to using `dev_to_iio_dev()`
instead.
This driver is one of the last few drivers remaining that uses the outdated
idiom, update it. This will allow to eventually update the IIO core to no
longer set the drvdata for the IIO device and free it up for driver usage.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Link: https://lore.kernel.org/r/20211019082929.30503-2-lars@metafoo.de
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The at91-sama5d2 driver calls `to_platform_device()` on a struct device
that is part of a IIO device. This is incorrect since
`to_platform_device()` must only be called on a struct device that is part
of a platform device.
The code still works by accident because non of the struct platform_device
specific fields are accessed.
Refactor the code a bit so that it behaves identically, but does not use
the incorrect cast. This avoids accidentally adding undefined behavior in
the future by assuming the `struct platform_device` is actually valid.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Tested-by: Eugen Hristev <eugen.hristev@microchip.com>
Link: https://lore.kernel.org/r/20211019082929.30503-1-lars@metafoo.de
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The IIO core handles a trigger ops with all NULL callbacks the
same as if the trigger ops itself was NULL.
Remove the empty trigger ops from the interrupt trigger driver to slightly
reduce the boilerplate code. Object size of the driver module is also
slightly reduced.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Link: https://lore.kernel.org/r/20211031142130.20791-9-lars@metafoo.de
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The IIO core handles a trigger ops with all NULL callbacks the
same as if the trigger ops itself was NULL.
Remove the empty trigger ops from the interrupt trigger driver to slightly
reduce the boilerplate code. Object size of the driver module is also
slightly reduced.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Link: https://lore.kernel.org/r/20211031142130.20791-8-lars@metafoo.de
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The IIO core handles a trigger ops with all NULL callbacks the same as if
the trigger ops itself was NULL.
Remove the empty trigger ops from the interrupt trigger driver to slightly
reduce the boilerplate code. Object size of the driver module is also
slightly reduced.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Link: https://lore.kernel.org/r/20211031142130.20791-7-lars@metafoo.de
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The IIO core handles a trigger ops with all NULL callbacks the
same as if the trigger ops itself was NULL.
Remove the empty trigger ops from the interrupt trigger driver to slightly
reduce the boilerplate code. Object size of the driver module is also
slightly reduced.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Link: https://lore.kernel.org/r/20211031142130.20791-6-lars@metafoo.de
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The IIO core handles a trigger ops with all NULL callbacks the
same as if the trigger ops itself was NULL.
Remove the empty trigger ops from the interrupt trigger driver to slightly
reduce the boilerplate code. Object size of the driver module is also
slightly reduced.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Link: https://lore.kernel.org/r/20211031142130.20791-5-lars@metafoo.de
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The IIO core handles a trigger ops with all NULL callbacks the
same as if the trigger ops itself was NULL.
Remove the empty trigger ops from the interrupt trigger driver to slightly
reduce the boilerplate code. Object size of the driver module is also
slightly reduced.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Link: https://lore.kernel.org/r/20211031142130.20791-4-lars@metafoo.de
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The IIO core handles a trigger ops with all NULL callbacks the
same as if the trigger ops itself was NULL.
Remove the empty trigger ops from the interrupt trigger driver to slightly
reduce the boilerplate code. Object size of the driver module is also
slightly reduced.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Link: https://lore.kernel.org/r/20211031142130.20791-3-lars@metafoo.de
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The IIO core handles a trigger ops with all NULL callbacks the
same as if the trigger ops itself was NULL.
Remove the empty trigger ops from the interrupt trigger driver to slightly
reduce the boilerplate code. Object size of the driver module is also
slightly reduced.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Link: https://lore.kernel.org/r/20211031142130.20791-2-lars@metafoo.de
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The IIO core handles a trigger ops with all NULL callbacks the
same as if the trigger ops itself was NULL.
Remove the empty trigger ops from the interrupt trigger driver to slightly
reduce the boilerplate code. Object size of the driver module is also
slightly reduced.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Link: https://lore.kernel.org/r/20211031142130.20791-1-lars@metafoo.de
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The ms5611 passes &indio_dev->dev as a parameter to all its IO callbacks
only to directly cast the struct device back to struct iio_dev. And the
struct iio_dev is then only used to get the drivers state struct.
Simplify this a bit by passing the state struct directly. This makes it a
bit easier to follow what the code is doing.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Link: https://lore.kernel.org/r/20211020142110.7060-1-lars@metafoo.de
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The `imx7d_adc_enable()` and `imx7d_adc_disable()` functions are used as
the suspend and resume callbacks for the device. When called as
suspend/resume functions they are called with the platform_device's device
as their parameter.
In addition the functions are called on device probe and remove. In this
case they are passed the struct device of the IIO device that the driver
registers.
This works because in the `imx7d_adc_{enable,disable}()` functions the
passed struct device is only ever used as a parameter to `dev_get_drvdata()`
and `dev_get_drvdata()` returns the same value for the platform device and
the IIO device.
But for consistency we should pass the same struct device to the
`imx7d_adc_{enable,disable}()` in all cases. This will avoid accidental
breakage if the device is ever used for something more than
`dev_get_drvdata()`.
Another motivation is that `dev_get_drvdata()` on the IIO device relies on
the IIO core calling `dev_set_drvdata()`. Something we want to remove.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Link: https://lore.kernel.org/r/20211020085754.16654-1-lars@metafoo.de
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Using `dev_get_drvdata()` in IIO sysfs callbacks to get a pointer to the
IIO device is a relic from the very early days of IIO. The IIO core as well
as most other drivers have switched over to using `dev_to_iio_dev()`
instead.
This driver is one of the last few drivers remaining that uses the outdated
idiom, update it. This will allow to eventually update the IIO core to no
longer set the drvdata for the IIO device and free it up for driver usage.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Link: https://lore.kernel.org/r/20211020085349.16178-1-lars@metafoo.de
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
In some setups the IRQ signal of the XADC might not be wired to the host
system. The driver currently requires that an interrupt is specified. Make
the interrupt optional so the driver can be used in such setups where the
interrupt is not connected.
Since both the internal triggers as well as events depend on the interrupt
being connected both are not available when the interrupt is not connected.
Buffered access is still supported even without an interrupt since an
external trigger can be used.
The IRQ is only optional when using the AXI interface, since the PCAP
interface needs the IRQ for reading and writing registers.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Link: https://lore.kernel.org/r/20211021125950.28707-1-lars@metafoo.de
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
clk_get_rate() is not guaranteed to work if called before
clk_prepare_enable().
Reorder clk_get_rate(), so it's called after clk_prepare_enable() and
after devm_add_action_or_reset() of lpc18xx_clk_disable().
Not that this is not a problem on this particular device, but it is
good to remove a case that might get copied elsewhere.
Suggested-by: Jonathan Cameron <jic23@kernel.org>
Acked-by: Vladimir Zapolskiy <vz@mleia.com>
Signed-off-by: André Gustavo Nakagomi Lopez <andregnl@usp.br>
Link: https://lore.kernel.org/r/YXag5l4xBkGQH3tq@Andryuu.br
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
