Host needs to pass at least on bssid with all 0xff to firmware in
WMI_START_SCAN_CMDID, otherwise the bssid and receiver address
in probe requeste are all ZEROs.
This also fixed some hidden AP connection issue because some AP
doesn't respond to probe request which receiver address are all
ZEROs.
Tested-on: QCA6390 hw2.0 PCI WLAN.HST.1.0.1-01740-QCAHSTSWPLZ_V2_TO_X86-1
Signed-off-by: Carl Huang <cjhuang@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20201012101733.24137-1-cjhuang@codeaurora.org
The firmware parameter LINK_FAIL_TX_CNT maps to the prima configuration
file parameter gLinkFailTxCnt and is described as:
quote: " If within gLinkFailTimeout period(values is mentioned in msec) if
FW doesn't receive acks for gLinkFailTxCnt number of packets, then
link will be disconnected."
The downstream description sets a minimum value of 1000 a maximum value of
60000 and a default value of 6000, however it appears that unless we
actually set this value deliberately firmware defaults it to 0.
Setting this value to non-zero results in the firmware doing link
monitoring. The working example from downstream paradoxically sets the
value to 200, here we opt to set the value to the minimum stipulated in the
configuration file 1000.
In conjunction with ieee80211_hw_set(wcn->hw, CONNECTION_MONITOR); this
change effects offload of link monitoring to the firmware.
Tested with:
'CNSS-PR-2-0-1-2-c1-74-130449-3' wcn3620
'CNSS-PR-2-0-1-2-c1-00083' wcn3680
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20201103121735.291324-2-bryan.odonoghue@linaro.org
gcc -Wextra points out a type mismatch
drivers/net/wireless/ath/ath6kl/wmi.c: In function 'ath6kl_wmi_cmd_send':
drivers/net/wireless/ath/ath6kl/wmi.c:1825:19: warning: implicit conversion from 'enum <anonymous>' to 'enum wmi_data_hdr_data_type' [-Wenum-conversion]
1825 | false, false, 0, NULL, if_idx);
| ^~~~~
As far as I can tell, the numeric value is current here,
so just use the correct enum literal instead of 'false'.
Fixes: bdcd817079 ("Add ath6kl cleaned up driver")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20201026213040.3889546-9-arnd@kernel.org
Fixes the following W=1 kernel build warning(s):
drivers/net/wireless/ath/ath9k/ar5008_phy.c:119: warning: Function parameter or member 'rfBuf' not described in 'ar5008_hw_phy_modify_rx_buffer'
drivers/net/wireless/ath/ath9k/ar5008_phy.c:119: warning: Function parameter or member 'reg32' not described in 'ar5008_hw_phy_modify_rx_buffer'
drivers/net/wireless/ath/ath9k/ar5008_phy.c:119: warning: Function parameter or member 'numBits' not described in 'ar5008_hw_phy_modify_rx_buffer'
drivers/net/wireless/ath/ath9k/ar5008_phy.c:119: warning: Function parameter or member 'firstBit' not described in 'ar5008_hw_phy_modify_rx_buffer'
Cc: QCA ath9k Development <ath9k-devel@qca.qualcomm.com>
Cc: Kalle Valo <kvalo@codeaurora.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: linux-wireless@vger.kernel.org
Cc: netdev@vger.kernel.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20201102112410.1049272-21-lee.jones@linaro.org
There are only a couple of these and none of them are conformant.
Fixes the following W=1 kernel build warning(s):
drivers/net/wireless/ath/dfs_pri_detector.c:39: warning: Function parameter or member 'head' not described in 'pulse_elem'
drivers/net/wireless/ath/dfs_pri_detector.c:46: warning: Function parameter or member 'val' not described in 'pde_get_multiple'
drivers/net/wireless/ath/dfs_pri_detector.c:46: warning: Function parameter or member 'fraction' not described in 'pde_get_multiple'
drivers/net/wireless/ath/dfs_pri_detector.c:46: warning: Function parameter or member 'tolerance' not described in 'pde_get_multiple'
Cc: Kalle Valo <kvalo@codeaurora.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: linux-wireless@vger.kernel.org
Cc: netdev@vger.kernel.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20201102112410.1049272-23-lee.jones@linaro.org
Fixes the following W=1 kernel build warning(s):
drivers/net/wireless/ath/dfs_pattern_detector.c:34: warning: Function parameter or member 'region' not described in 'radar_types'
drivers/net/wireless/ath/dfs_pattern_detector.c:141: warning: Function parameter or member 'region' not described in 'get_dfs_domain_radar_types'
drivers/net/wireless/ath/dfs_pattern_detector.c:239: warning: Function parameter or member 'dpd' not described in 'channel_detector_get'
drivers/net/wireless/ath/dfs_pattern_detector.c:239: warning: Function parameter or member 'freq' not described in 'channel_detector_get'
Cc: Kalle Valo <kvalo@codeaurora.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: linux-wireless@vger.kernel.org
Cc: netdev@vger.kernel.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20201102112410.1049272-22-lee.jones@linaro.org
Assign the correct hw_op ath11k_init_wmi_config_ipq8074 to
the hw IPQ8074. Also update the correct TWT radio count.
Incorrect TWT radio count cause TWT feature fails on radio2
because physical device count is hardcoded to 2. so set
the value dynamically.
Found this during code review.
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.1.0.1-01238-QCAHKSWPL_SILICONZ-2
Fixes: 2d4bcbed5b ("ath11k: initialize wmi config based on hw_params")
Signed-off-by: Karthikeyan Periyasamy <periyasa@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1604512020-25197-1-git-send-email-periyasa@codeaurora.org
Below listed hal descriptor mask are incorrect, so modify it to correct one
- CE destination status description meta info mask is increased from
8 bits to 16 bits from the 0th bit position
- Rx Reo queue duplicate count mask is decreased from 22 bits to 16 bits
- Reo threshold status counter sum mask is increased from 24 bits to 26 bits
No functionality impact, these descriptors are currently not used in any
supported platform. But in future if someone referred these descriptor then
ended with wrong values.
Found this during code review.
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.1.0.1-01238-QCAHKSWPL_SILICONZ-2
Signed-off-by: Karthikeyan Periyasamy <periyasa@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1604511921-24840-1-git-send-email-periyasa@codeaurora.org
driver not able to bootup in the single radio configured board.
single phy hw mode is converted to invalid hw mode and sent to FW
through wmi init cmd. In that case driver is not receiving wmi
ready event which leads to driver bootup fail. single phy hw mode
is a valid for single radio configured board. so removed the
conversion logic.
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.1.0.1-01238-QCAHKSWPL_SILICONZ-2
Signed-off-by: Karthikeyan Periyasamy <periyasa@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1604511331-22477-1-git-send-email-periyasa@codeaurora.org
The ath11k code will try to insert wheather rader related limits when the
DFS region is set to ETSI. For this reason, it will add two more entries in
the array of reg_rules. But the 2.4.0.1 firmware is prefiltering the list
of reg rules it returns for 2.4GHz PHYs. They will then not contain the
list of 5GHz rules and thus no wheather radar band rules were inserted by
this code.
But the code didn't fix the n_reg_rules for this regulatory domain and PHY
when this happened. This resulted in a rejection by is_valid_rd because it
found rules which start and end at 0khz. This resulted in a splat like:
Invalid regulatory domain detected
------------[ cut here ]------------
WARNING: at backports-20200628-4.4.60-9a94b73e75/net/wireless/reg.c:3721
[...]
ath11k c000000.wifi1: failed to perform regd update : -22
The number of rules must therefore be saved after they were converted from
the ath11k format to the ieee80211_regdomain format and not before.
Tested with IPQ8074 WLAN.HK.2.4.0.1.r1-00019-QCAHKSWPL_SILICONZ-1
Fixes: d5c65159f2 ("ath11k: driver for Qualcomm IEEE 802.11ax devices")
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20201030101940.2387952-1-sven@narfation.org
The function ath11k_wmi_send_init_country_cmd is taking 3 byte from alpha2
of the structure wmi_init_country_params. But the function
ath11k_reg_notifier is only initializing 2 bytes. The third byte is
therefore always an uninitialized value.
The command can happen to look like
0c 00 87 02 01 00 00 00 00 00 00 00 43 41 f8 00
instead of
0c 00 87 02 01 00 00 00 00 00 00 00 43 41 00 00
Tested-on: IPQ8074 hw2.0 WLAN.HK.2.1.0.1-01161-QCAHKSWPL_SILICONZ-1
Tested-on: IPQ8074 hw2.0 WLAN.HK.2.1.0.1-01228-QCAHKSWPL_SILICONZ-1
Tested-on: IPQ8074 hw2.0 WLAN.HK.2.1.0.1-01238-QCAHKSWPL_SILICONZ-2
Tested-on: IPQ8074 hw2.0 WLAN.HK.2.4.0.1.r1-00019-QCAHKSWPL_SILICONZ-1
Tested-on: IPQ8074 hw2.0 WLAN.HK.2.4.0.1.r1-00026-QCAHKSWPL_SILICONZ-2
Fixes: d5c65159f2 ("ath11k: driver for Qualcomm IEEE 802.11ax devices")
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20201021140555.4114715-1-sven@narfation.org
cold boot calibration is the process to calibrate all the channels
during the boot-up to avoid the calibration delay during the
channel change.
During the boot-up, firmware started in cold boot calibration mode
Firmware calibrate all channels and generate CalDb(DDR).
Subsequent wifi bringup will reuse the same CalDb.
Firmware is restarted in normal mode to continue the normal operation.
caldb memory address send to firmware through the QMI message.Firmware
use this address to store the caldb data and use it until next reboot.
This will give the improvement during the channel change. But it is
increasing the boot-up time(up to 15sec depend on number of radios).
So if the user want to reduce the boot-up time and accepting for channel
change delay, user can disable this feature using the module param
cold_boot_cal=0.
Tested-on: IPQ8074 WLAN.HK.2.4.0.1-01162-QCAHKSWPL_SILICONZ-1
Signed-off-by: Govindaraj Saminathan <gsamin@codeaurora.org>
Co-developed-by: Sowmiya Sree Elavalagan <ssreeela@codeaurora.org>
Signed-off-by: Sowmiya Sree Elavalagan <ssreeela@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1602862111-14063-1-git-send-email-ssreeela@codeaurora.org
Board Data File (BDF) is loaded upon driver boot-up procedure. The right
board data file is identified on IPQ6018 using bus, qmi-chip-id and
qmi-board-id.
The problem, however, can occur when the (default) board data file cannot
fulfill with the vendor requirements and it is necessary to use a different
board data file.
This problem was already solved on ath10k by adding a ",variant=.*" at the
end of the board name. The same functionality must also be provided for
ath11k.
The device tree requires an additional string to define the variant name
wifi@c000000 {
status = "okay";
qcom,ath11k-calibration-variant = "Cigtech-WF-188";
};
This would create the boarddata identifier for the board-2.bin search
* bus=ahb,qmi-chip-id=0,qmi-board-id=18,variant=Cigtech-WF-188
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20201015131501.1939685-2-sven@narfation.org
The bus + qmi-chip-id + qmi-board-id is not enough to identify the correct
board data file on IPQ6018 based devices. Multiple different boards share
the same values. Only the original reference designs can currently be
identified and loaded from the board-2.bin. But these will not result in
the correct calibration data when combined with the pre-calibration data
from the device.
An additional "variant" information has to be provided to select the
correct board data for a design which was modified by an ODM. This follows
the same approach as ath10k.
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20201015131501.1939685-1-sven@narfation.org
The rx worker of SDIO should be cancelled after disable interrupt, and
release rx sk_buff in queue, otherwise the rx worker maybe still run
after hif_stop. And it should be cancelled before napi_synchronize in
hif_stop, because the rx worker of SDIO will call napi_schedule, it
should have no napi_schedule before napi_synchronize, otherwise it
lead napi_synchronize wait untill napi_complete.
Tested-on: QCA6174 hw3.2 SDIO WLAN.RMH.4.4.1-00049
Signed-off-by: Wen Gong <wgong@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1604558036-4056-1-git-send-email-wgong@codeaurora.org
This patch adds driver support for FILS discovery and unsolicited
broadcast probe response transmission features which are used for
in-band discovery in 6GHz band.
Currently this support is enabled only in 6GHz by setting hardware flags.
Changes include WMI commands to enable transmission, set packet
interval, set template, and handle events.
Signed-off-by: Aloka Dixit <alokad@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20201007204036.19780-1-alokad@codeaurora.org
The for loop checks whether cur_section is NULL on every iteration, but
we know it can never be NULL as there is another check towards the
bottom of the loop body. Refactor to avoid this unnecessary check.
Also, increment the variable i inline for clarity
Addresses-Coverity: 1496984 ("Null pointer dereferences)
Suggested-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: Alex Dewar <alex.dewar90@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200916165748.20927-1-alex.dewar90@gmail.com
tid_addr is not a "pointer to (pointer to int in userspace)"; it is in
fact a "pointer to (pointer to int in userspace) in userspace". So
sparse rightfully complains about passing a kernel pointer to
put_user().
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Commit 453431a549 ("mm, treewide: rename kzfree() to
kfree_sensitive()") renamed kzfree() to kfree_sensitive(),
but it left a compatibility definition of kzfree() to avoid
being too disruptive.
Since then a few more instances of kzfree() have slipped in.
Just get rid of them and remove the compatibility definition
once and for all.
Signed-off-by: Eric Biggers <ebiggers@google.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Pull timer fixes from Thomas Gleixner:
"A time namespace fix and a matching selftest. The futex absolute
timeouts which are based on CLOCK_MONOTONIC require time namespace
corrected. This was missed in the original time namesapce support"
* tag 'timers-urgent-2020-10-25' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
selftests/timens: Add a test for futex()
futex: Adjust absolute futex timeouts with per time namespace offset
Pull scheduler fixes from Thomas Gleixner:
"Two scheduler fixes:
- A trivial build fix for sched_feat() to compile correctly with
CONFIG_JUMP_LABEL=n
- Replace a zero lenght array with a flexible array"
* tag 'sched-urgent-2020-10-25' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
sched/features: Fix !CONFIG_JUMP_LABEL case
sched: Replace zero-length array with flexible-array
Pull perf fix from Thomas Gleixner:
"A single fix to compute the field offset of the SNOOPX bit in the data
source bitmask of perf events correctly"
* tag 'perf-urgent-2020-10-25' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
perf: correct SNOOPX field offset
Pull locking fix from Thomas Gleixner:
"Just a trivial fix for kernel-doc warnings"
* tag 'locking-urgent-2020-10-25' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
locking/seqlocks: Fix kernel-doc warnings
Pull NTB fixes from Jon Mason.
* tag 'ntb-5.10' of git://github.com/jonmason/ntb:
NTB: Use struct_size() helper in devm_kzalloc()
ntb: intel: Fix memleak in intel_ntb_pci_probe
NTB: hw: amd: fix an issue about leak system resources
Pull i2c fix from Wolfram Sang:
"Regression fix for rc1 and stable kernels as well"
* 'i2c/for-5.10' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux:
i2c: core: Restore acpi_walk_dep_device_list() getting called after registering the ACPI i2c devs
Pull more cifs updates from Steve French:
"Add support for stat of various special file types (WSL reparse points
for char, block, fifo)"
* tag '5.10-rc-smb3-fixes-part2' of git://git.samba.org/sfrench/cifs-2.6:
cifs: update internal module version number
smb3: add some missing definitions from MS-FSCC
smb3: remove two unused variables
smb3: add support for stat of WSL reparse points for special file types
Pull more parisc updates from Helge Deller:
- During this merge window O_NONBLOCK was changed to become 000200000,
but we missed that the syscalls timerfd_create(), signalfd4(),
eventfd2(), pipe2(), inotify_init1() and userfaultfd() do a strict
bit-wise check of the flags parameter.
To provide backward compatibility with existing userspace we
introduce parisc specific wrappers for those syscalls which filter
out the old O_NONBLOCK value and replaces it with the new one.
- Prevent HIL bus driver to get stuck when keyboard or mouse isn't
attached
- Improve error return codes when setting rtc time
- Minor documentation fix in pata_ns87415.c
* 'parisc-5.10-2' of git://git.kernel.org/pub/scm/linux/kernel/git/deller/parisc-linux:
ata: pata_ns87415.c: Document support on parisc with superio chip
parisc: Add wrapper syscalls to fix O_NONBLOCK flag usage
hil/parisc: Disable HIL driver when it gets stuck
parisc: Improve error return codes when setting rtc time
Pull more xen updates from Juergen Gross:
- a series for the Xen pv block drivers adding module parameters for
better control of resource usge
- a cleanup series for the Xen event driver
* tag 'for-linus-5.10b-rc1c-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip:
Documentation: add xen.fifo_events kernel parameter description
xen/events: unmask a fifo event channel only if it was masked
xen/events: only register debug interrupt for 2-level events
xen/events: make struct irq_info private to events_base.c
xen: remove no longer used functions
xen-blkfront: Apply changed parameter name to the document
xen-blkfront: add a parameter for disabling of persistent grants
xen-blkback: add a parameter for disabling of persistent grants
Pull SafeSetID updates from Micah Morton:
"The changes are mostly contained to within the SafeSetID LSM, with the
exception of a few 1-line changes to change some ns_capable() calls to
ns_capable_setid() -- causing a flag (CAP_OPT_INSETID) to be set that
is examined by SafeSetID code and nothing else in the kernel.
The changes to SafeSetID internally allow for setting up GID
transition security policies, as already existed for UIDs"
* tag 'safesetid-5.10' of git://github.com/micah-morton/linux:
LSM: SafeSetID: Fix warnings reported by test bot
LSM: SafeSetID: Add GID security policy handling
LSM: Signal to SafeSetID when setting group IDs
