While adding SiI9022A support to the iwg23s board, it came
up that when the HDMI transmitter is in pass through mode the
device is not compliant with the I2C specification anymore,
as it requires a far bigger tbuf, due to a delay the HDMI
transmitter is adding when relaying the STOP condition on the
monitor i2c side of things.
When not providing an appropriate delay after the STOP condition
the i2c bus would get stuck. Also, any other traffic on the bus
while talking to the monitor may cause the transaction to fail
or even cause issues with the i2c bus as well.
I2c-gates seemed to reach consent as a possible way to address
these issues, and as such this patch is implementing a solution
based on that. Since others are clearly relying on the current
implementation of the driver, this patch won't require any DT
changes.
Since we don't want any interference during the DDC Bus
Request/Grant procedure and while talking to the monitor, we
have to use the adapter locking primitives rather than the
i2c-mux locking primitives.
Signed-off-by: Fabrizio Castro <fabrizio.castro@bp.renesas.com>
Reviewed-by: Peter Rosin <peda@axentia.se>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Tested-by: Yannick Fertré <yannick.fertre@st.com>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Link: https://patchwork.freedesktop.org/patch/msgid/1541505156-8097-1-git-send-email-fabrizio.castro@bp.renesas.com
The TPO TPG110 bindings were using the DPI bindings (popular
in the fbdev subsystem) but this misses the finer points
learned in the DRM subsystem.
We need to augment the bindings for proper DRM integration:
the timings are expressed by the hardware, not put into the
device tree. I.e. this hardware is self-describing and can
report the resolutions and timings needed. It should not
be described in the device tree.
Further the device was incorrectly modeled with GPIO lines
instead of an SPI child, even though the device was using
SPI.
No known deployments of the device using device tree
exist, so it should be fine to augment the bindings.
Cc: devicetree@vger.kernel.org
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20181101213256.12097-1-linus.walleij@linaro.org
Fixes gcc '-Wunused-but-set-variable' warning:
drivers/gpu/drm/qxl/qxl_release.c: In function 'qxl_release_fence_buffer_objects':
drivers/gpu/drm/qxl/qxl_release.c:431:17: warning:
variable 'qbo' set but not used [-Wunused-but-set-variable]
drivers/gpu/drm/qxl/qxl_release.c:430:24: warning:
variable 'driver' set but not used [-Wunused-but-set-variable]
'qbo' not used since commit f2c24b83ae ("drm/ttm: flip the switch, and convert
to dma_fence")
And 'driver' never used since introduction in
8002db6336 ("qxl: convert qxl driver to proper use for reservations")
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1542029556-88107-1-git-send-email-yuehaibing@huawei.com
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Add a new field called fence_fd that will be used by userspace to send
in-fences to the kernel and receive out-fences created by the kernel.
This uapi enables virtio to take advantage of explicit synchronization of
dma-bufs.
There are two new flags:
* VIRTGPU_EXECBUF_FENCE_FD_IN to be used when passing an in-fence fd.
* VIRTGPU_EXECBUF_FENCE_FD_OUT to be used when requesting an out-fence fd
The execbuffer IOCTL is now read-write to allow the userspace to read the
out-fence.
On error -1 should be returned in the fence_fd field.
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.com>
Signed-off-by: Robert Foss <robert.foss@collabora.com>
Reviewed-by: Emil Velikov <emil.velikov@collabora.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20181112165157.32765-3-robert.foss@collabora.com
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
This patch adds support for the Primary Plane scaling.
On the Amlogic GX SoCs, the primary plane is used as On-Screen-Display
layer on top of video, and it's needed to keep the OSD layer to a lower
size as the physical display size to :
- lower the memory bandwidth
- lower the OSD rendering
- lower the memory usage
This use-case is used when setting the display mode to 3840x2160 and the
OSD layer is rendered using the GPU. In this case, the GXBB & GXL cannot
work on more than 2000x2000 buffer, thus needing the OSD layer to be kept
at 1920x1080 and upscaled to 3840x2160 in hardware.
The primary plane atomic check still allow 1:1 scaling, allowing native
3840x2160 if needed by user-space applications.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch>
[narmstrong: fixed apply from malformed patch]
Link: https://patchwork.freedesktop.org/patch/msgid/1541497202-20570-4-git-send-email-narmstrong@baylibre.com
The Amlogic Meson GX SoCs support an Overlay plane behind the primary
plane for video rendering.
This Overlay plane support various YUV layouts :
- YUYV
- NV12 / NV21
- YUV444 / 422 / 420 / 411 / 410
The scaler supports a wide range of scaling ratios, but for simplicity,
plane atomic check limits the scaling from x5 to /5 in vertical and
horizontal scaling.
The z-order is fixed and always behind the primary plane and cannot be changed.
The scaling parameter algorithm was taken from the Amlogic vendor kernel
code and rewritten to match the atomic universal plane requirements.
The video rendering using this overlay plane support has been tested using
the new Kodi DRM-KMS Prime rendering path along the in-review V4L2 Mem2Mem
Hardware Video Decoder up to 3840x2160 NV12 frames on various display modes.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Tested-by: Maxime Jourdan <mjourdan@baylibre.com>
Link: https://patchwork.freedesktop.org/patch/msgid/1541497202-20570-2-git-send-email-narmstrong@baylibre.com
drm-next is forwarded to v4.20-rc1, and we need this to make
a patch series apply.
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
For the YUV conversion to work properly, ->x_scaling[1] should never
be set to VC4_SCALING_NONE, but vc4_get_scaling_mode() might return
VC4_SCALING_NONE if the horizontal scaling ratio exactly matches the
horizontal subsampling factor. Add a test to turn VC4_SCALING_NONE
into VC4_SCALING_PPF when that happens.
The old ->x_scaling[0] adjustment is dropped as I couldn't find any
mention to this constraint in the spec and it's proven to be
unnecessary (I tested various multi-planar YUV formats with scaling
disabled, and all of them worked fine without this adjustment).
Fixes: fc04023faf ("drm/vc4: Add support for YUV planes.")
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Reviewed-by: Eric Anholt <eric@anholt.net>
Link: https://patchwork.freedesktop.org/patch/msgid/20181109102633.32603-1-boris.brezillon@bootlin.com
Features such as dithering and pixel data edge configuration currently
rely on the panel registered with the TCON driver. However, bridges are
also supported in addition to panels for RGB setup.
Instead of retrieving the connector from the panel, get it from the
encoder with the dedicated helper.
Even in the case of bridges, the connector is registered with the
encoder from our driver and is accessible when iterating connectors.
Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181107181843.27628-3-contact@paulk.fr
Add a function to check whether there is at least one plane that
supports a specific format and modifier combination. Drivers can
use this to reject unsupported formats/modifiers in .fb_create().
v2: Accept anyformat if the driver doesn't do planes (Eric)
s/planes_have_format/any_plane_has_format/ (Eric)
Check the modifier as well since we already have a function
that does both
v3: Don't do the check in the core since we may not know the
modifier yet, instead export the function and let drivers
call it themselves
Cc: Eric Anholt <eric@anholt.net>
Cc: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181029183453.28541-1-ville.syrjala@linux.intel.com
It's lockless, and userspace might chance it underneath us. That's not
really a problem, all userspace gets is a slightly dysfunctional
lease with the current code. But this might change, and gcc might
decide to reload a few too many times, and then boom. So better safe
than sorry.
v2: Remove the now unused lessor_priv argument from validate_lease()
(Keith).
v3: Actually add everything ... silly me.
Cc: Keith Packard <keithp@keithp.com>
Cc: Dave Airlie <airlied@gmail.com>
Acked-by: Keith Packard <keithp@keithp.com>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181105101211.22737-1-daniel.vetter@ffwll.ch
H6 has Synopsys DWC HDMI 2.0 TX PHY.
There is no freely available documentation for it, only code found in
BSP kernel. However, judging by the code, PHY is very similar to older
Synopsys HDMI PHY described in i.MX6 documentation. Most registers seem
to be the same.
According to i.MX6 documentation, mpll settings are based on pixel clock
and are not specific to each SoC. Because of that, mpll table in this
commit is based on that documentation and not on BSP code. Other PHY
settings were derived from BSP PHY driver code.
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181104182705.18047-23-jernej.skrabec@siol.net
Currently sun8i-hdmi-phy driver supports only custom PHYs connected to
DW HDMI controller. Since newest Allwinner SoCs have unmodified Synopsys
PHY, driver has to be reorganized to support them.
Variant structure is expanded to allow differentiation between custom
and Sysnopsys PHYs and to hold Synopsys PHY settings.
Since DW HDMI bridge platform data has different fields for custom and
Sysnopsys PHY, function sun8i_hdmi_phy_get_ops() is replaced with
sun8i_hdmi_phy_set_ops().
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181104182705.18047-22-jernej.skrabec@siol.net
