Pull SoC devicetree updates from Arnd Bergmann:
"There are 11 newly supported SoCs, but these are all either new
variants of existing designs, or straight reuses of the existing chip
in a new package:
- RK3562 is a new chip based on the old Cortex-A53 core, apparently a
low-cost version of the Cortex-A55 based RK3568/RK3566.
- NXP i.MX94 is a minor variation of i.MX93/i.MX95 with a different
set of on-chip peripherals.
- Renesas RZ/V2N (R9A09G056) is a new member of the larger RZ/V2
family
- Amlogic S6/S7/S7D
- Samsung Exynos7870 is an older chip similar to Exynos7885
- WonderMedia wm8950 is a minor variation on the wm8850 chip
- Amlogic s805y is almost idential to s805x
- Allwinner A523 is similar to A527 and T527
- Qualcomm MSM8926 is a variant of MSM8226
- Qualcomm Snapdragon X1P42100 is related to R1E80100
There are also 65 boards, including reference designs for the chips
above, this includes
- 12 new boards based on TI K3 series chips, most of them from
Toradex
- 10 devices using Rockchips RK35xx and PX30 chips
- 2 phones and 2 laptops based on Qualcomm Snapdragon designs
- 10 NXP i.MX8/i.MX9 boards, mostly for embedded/industrial uses
- 3 Samsung Galaxy phones based on Exynos7870
- 5 Allwinner based boards using a variety of ARMv8 chips
- 9 32-bit machines, each based on a different SoC family
Aside from the new hardware, there is the usual set of cleanups and
newly added hardware support on existing machines, for a total of 965
devicetree changesets"
* tag 'soc-dt-6.16' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (956 commits)
MAINTAINERS, mailmap: update Sven Peter's email address
arm64: dts: renesas: rzg3e-smarc-som: Reduce I2C2 clock frequency
arm64: dts: nuvoton: Add pinctrl
ARM: dts: samsung: sp5v210-aries: Align wifi node name with bindings
arm64: dts: blaize-blzp1600: Enable GPIO support
dt-bindings: clock: socfpga: convert to yaml
arm64: dts: rockchip: move rk3562 pinctrl node outside the soc node
arm64: dts: rockchip: fix rk3562 pcie unit addresses
arm64: dts: rockchip: move rk3528 pinctrl node outside the soc node
arm64: dts: rockchip: remove a double-empty line from rk3576 core dtsi
arm64: dts: rockchip: move rk3576 pinctrl node outside the soc node
arm64: dts: rockchip: fix rk3576 pcie unit addresses
arm64: dts: rockchip: Drop assigned-clock* from cpu nodes on rk3588
arm64: dts: rockchip: Add missing SFC power-domains to rk3576
Revert "arm64: dts: mediatek: mt8390-genio-common: Add firmware-name for scp0"
arm64: dts: mediatek: mt8188: Address binding warnings for MDP3 nodes
arm64: dts: mt6359: Rename RTC node to match binding expectations
arm64: dts: mt8365-evk: Add goodix touchscreen support
arm64: dts: mediatek: mt8188: Add missing #reset-cells property
arm64: dts: airoha: en7581: Add PCIe nodes to EN7581 SoC evaluation board
...
Pull ARM SoC updates from Arnd Bergmann:
"The main update in size is the removal of the TI DaVinci DA830 SoC
support. DA830 is similar to DA850, which remain supported, but only
the reference board was ever supported, and we removed that one 3
years ago as it had never been converted to devicetree.
There are some other cleanups for OMAP4 and a few boards using old
GPIO interfaces"
* tag 'soc-arm-6.16' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc:
ARM: s3c: stop including gpio.h
ARM: dts: davinci: da850-evm: Increase fifo threshold
ARM: OMAP2+: Fix l4ls clk domain handling in STANDBY
ARM: broadcom: MAINTAINERS: Cover bcm2712 files
bus: ti-sysc: PRUSS OCP configuration
ARM: davinci: remove support for da830
ARM: omap: pmic-cpcap: do not mess around without CPCAP or OMAP4
ARM: omap2plus_defconfig: enable I2C devices of GTA04
ARM: s3c/gpio: use new line value setter callbacks
ARM: scoop/gpio: use new line value setter callbacks
ARM: sa1100/gpio: use new line value setter callbacks
ARM: orion/gpio: use new line value setter callbacks
Pull EFI updates from Ard Biesheuvel:
"Not a lot going on in the EFI tree this cycle. The only thing that
stands out is the new support for SBAT metadata, which was a bit
contentious when it was first proposed, because in the initial
incarnation, it would have required us to maintain a revocation index,
and bump it each time a vulnerability affecting UEFI secure boot got
fixed. This was shot down for obvious reasons.
This time, only the changes needed to emit the SBAT section into the
PE/COFF image are being carried upstream, and it is up to the distros
to decide what to put in there when creating and signing the build.
This only has the EFI zboot bits (which the distros will be using for
arm64); the x86 bzImage changes should be arriving next cycle,
presumably via the -tip tree.
Summary:
- Add support for emitting a .sbat section into the EFI zboot image,
so that downstreams can easily include revocation metadata in the
signed EFI images
- Align PE symbolic constant names with other projects
- Bug fix for the efi_test module
- Log the physical address and size of the EFI memory map when
failing to map it
- A kerneldoc fix for the EFI stub code"
* tag 'efi-next-for-v6.16' of git://git.kernel.org/pub/scm/linux/kernel/git/efi/efi:
include: pe.h: Fix PE definitions
efi/efi_test: Fix missing pending status update in getwakeuptime
efi: zboot specific mechanism for embedding SBAT section
efi/libstub: Describe missing 'out' parameter in efi_load_initrd
efi: Improve logging around memmap init
Pull hardening updates from Kees Cook:
- Update overflow helpers to ease refactoring of on-stack flex array
instances (Gustavo A. R. Silva, Kees Cook)
- lkdtm: Use SLAB_NO_MERGE instead of constructors (Harry Yoo)
- Simplify CONFIG_CC_HAS_COUNTED_BY (Jan Hendrik Farr)
- Disable u64 usercopy KUnit test on 32-bit SPARC (Thomas Weißschuh)
- Add missed designated initializers now exposed by fixed randstruct
(Nathan Chancellor, Kees Cook)
- Document compilers versions for __builtin_dynamic_object_size
- Remove ARM_SSP_PER_TASK GCC plugin
- Fix GCC plugin randstruct, add selftests, and restore COMPILE_TEST
builds
- Kbuild: induce full rebuilds when dependencies change with GCC
plugins, the Clang sanitizer .scl file, or the randstruct seed.
- Kbuild: Switch from -Wvla to -Wvla-larger-than=1
- Correct several __nonstring uses for -Wunterminated-string-initialization
* tag 'hardening-v6.16-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/kees/linux: (23 commits)
Revert "hardening: Disable GCC randstruct for COMPILE_TEST"
lib/tests: randstruct: Add deep function pointer layout test
lib/tests: Add randstruct KUnit test
randstruct: gcc-plugin: Remove bogus void member
net: qede: Initialize qede_ll_ops with designated initializer
scsi: qedf: Use designated initializer for struct qed_fcoe_cb_ops
md/bcache: Mark __nonstring look-up table
integer-wrap: Force full rebuild when .scl file changes
randstruct: Force full rebuild when seed changes
gcc-plugins: Force full rebuild when plugins change
kbuild: Switch from -Wvla to -Wvla-larger-than=1
hardening: simplify CONFIG_CC_HAS_COUNTED_BY
overflow: Fix direct struct member initialization in _DEFINE_FLEX()
kunit/overflow: Add tests for STACK_FLEX_ARRAY_SIZE() helper
overflow: Add STACK_FLEX_ARRAY_SIZE() helper
input/joystick: magellan: Mark __nonstring look-up table const
watchdog: exar: Shorten identity name to fit correctly
mod_devicetable: Enlarge the maximum platform_device_id name length
overflow: Clarify expectations for getting DEFINE_FLEX variable sizes
compiler_types: Identify compiler versions for __builtin_dynamic_object_size
...
More Arm32 DeviceTree updates for v6.16
This adds missing LVDS clocks to APQ8064 display controller. The unused HDMI HPD
gpio on ifc6410 is dropped (chip uses pinmuxed hpd function).
Missing timer clocks are added to MSM8960 to address bindings warning.
* tag 'qcom-arm32-for-6.16-2' of https://git.kernel.org/pub/scm/linux/kernel/git/qcom/linux:
ARM: dts: qcom: apq8064-ifc6410: drop HDMI HPD GPIO
ARM: dts: qcom: apq8064: link LVDS clocks
ARM: dts: qcom-msm8960: add missing clocks to the timer node
Link: https://lore.kernel.org/r/20250520024716.39418-1-andersson@kernel.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Allwinner device tree changes for 6.16
Introduce Allwinner A523 / A527 / T527 SoC family w/ three new devices:
- Radxa Cubie A5E
- X96Q-Pro+
- Avaota-A1
Also enable EMAC0 ethernet MAC on A523 family for Cubie A5E & Avaota-A1.
Note: the SoC has two different ethernet controllers.
Changes to existing SoCs:
- Enable GPU on H616 with all boards enabled
- Set maximum MMC frequency for the A100
Changes to existing boards:
- Add WiFi/BT header on PINE64 A64 boards
- Add hp-det-gpios for Anbernic RG35XX
- Add support for PHY LEDs on Bananapi (the original one)
Add new devices for existing SoCs:
- YuzukiHD Chameleon based on H6
- Liontron H-A133L based on A133 (compatible with A100)
Tree wide cleanups:
- Use preferred node names for cooling maps
- Align wifi node name with bindings
- Drop spurious 'clock-latency-ns' properties for H5 & H6
* tag 'sunxi-dt-for-6.16' of https://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux: (27 commits)
arm64: dts: allwinner: a100: add Liontron H-A133L board support
dt-bindings: arm: sunxi: Add Liontron H-A133L board name
dt-bindings: vendor-prefixes: Add Liontron name
ARM: dts: bananapi: add support for PHY LEDs
arm64: dts: allwinner: a100: set maximum MMC frequency
arm64: dts: allwinner: t527: add EMAC0 to Avaota-A1 board
arm64: dts: allwinner: a527: add EMAC0 to Radxa A5E board
arm64: dts: allwinner: a523: Add EMAC0 ethernet MAC
dt-bindings: sram: sunxi-sram: Add A523 compatible
arm64: dts: allwinner: a64: Add WiFi/BT header on SOPINE Baseboard
arm64: dts: allwinner: a64: Add WiFi/BT header on PINE A64
arm64: dts: allwinner: correct the model name for Radxa Cubie A5E
ARM: dts: allwinner: Align wifi node name with bindings
arm64: dts: allwinner: Align wifi node name with bindings
arm64: dts: allwinner: h616: enable Mali GPU for all boards
arm64: dts: allwinner: h616: Add Mali GPU node
arm64: dts: allwinner: h700: Add hp-det-gpios for Anbernic RG35XX
arm64: dts: allwinner: h5/h6: Drop spurious 'clock-latency-ns' properties
arm/arm64: dts: allwinner: Use preferred node names for cooling maps
arm64: dts: allwinner: h616: add YuzukiHD Chameleon support
...
Link: https://lore.kernel.org/r/aCaeZJ2t4S_xhgjp@wens.tw
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
STM32 DT for v6.16, round 1
Highlights:
----------
- MCU:
- Add low power timer on STM32F746
- Add STM32H747 High end MCU support. It embeds:
- dual-core (Cortex-M7 + Cortex-M4)
- up to 2 Mbytes flash
- 1 Mbyte of internal RAM
- Add STM32H747i-disco board support. Detailed information can be
found at:
https://www.st.com/en/evaluation-tools/stm32h747i-disco.html
- MPU:
- STM32MP13:
- Add VREFINT calibration support based on ADC.
- STMP32MP15:
- Add new Ultratronik Fly board support:
- based on STM32MP157C SoC
- 1GB of DDR3
- Several connections are available on this boards:
2*USB2.0, 1*USB2.0 MiniUSB, Debug UART, 1*UART, 1*USART,
SDcard, RJ45, ...
- STM32MP25:
- Add OCTOSPI support on STM32MP25 SoCs
- Add SPI NOR flash support on STM32MP257F-EV1 connected to OSPI1
- Add Low power timer TIMER (LPTIM) on STM32MP25 SoCs and use
LPTIM3 as low power broadcast timer on STM32MP257F-EV1.
* tag 'stm32-dt-for-v6.16-1' of https://git.kernel.org/pub/scm/linux/kernel/git/atorgue/stm32: (22 commits)
ARM: dts: stm32: add initial support for stm32mp157-ultra-fly-sbc board
MAINTAINERS: Add entry for ULTRATRONIK BOARD SUPPORT
dt-bindings: arm: stm32: Document Ultratronik's Fly board DT binding
dt-bindings: vendor-prefixes: Add Ultratronik
arm64: dts: st: use lptimer3 as tick broadcast source on stm32mp257f-ev1
arm64: dts: st: add low-power timer nodes on stm32mp251
arm64: defconfig: enable STM32 LP timer clockevent driver
arm64: dts: st: Add SPI NOR flash support on stm32mp257f-ev1 board
arm64: dts: st: Add ospi port1 pinctrl entries in stm32mp25-pinctrl.dtsi
arm64: dts: st: Add OMM node on stm32mp251
ARM: dts: stm32: support STM32h747i-disco board
ARM: dts: stm32: add an extra pin map for USART1 on stm32h743
ARM: dts: stm32: add pin map for UART8 controller on stm32h743
ARM: dts: stm32: add uart8 node for stm32h743 MCU
dt-bindings: clock: stm32h7: rename USART{7,8}_CK to UART{7,8}_CK
ARM: stm32: add a new SoC - STM32H747
dt-bindings: arm: stm32: add compatible for stm32h747i-disco board
ARM: dts: stm32h7-pinctrl: add _a suffix to u[s]art_pins phandles
ARM: dts: st: stm32: Align wifi node name with bindings
ARM: dts: stm32: add low power timer on STM32F746
...
Link: https://lore.kernel.org/r/2f101efb-6d58-48d8-983a-57e30a34827c@foss.st.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Qualcomm Arm32 DeviceTree updates for v6.16
Introduce support for the AP8064-based LG Nexus 4. MSM8226 is extended
with modem-related features, the LTE-capable variant MSM8926 is
introduced, and modem support is enabled on Samsung Galaxy Tab 4.
Display-related clocks and power-domains are defined for the simple
framebuffer of Motorola Moto G, to allow booting without
clk_ignore_unused and pd_ignore_unused.
On MSM8960 SDCC BAM and thermal sensor (tsens) is introduced.
* tag 'qcom-arm32-for-6.16' of https://git.kernel.org/pub/scm/linux/kernel/git/qcom/linux:
ARM: dts: qcom: apq8064: move replicator out of soc node
ARM: dts: qcom: apq8064: use new compatible for SPS SIC device
ARM: dts: qcom: apq8064: use new compatible for SFPB device
ARM: dts: qcom: apq8064 merge hw splinlock into corresponding syscon device
ARM: dts: qcom: apq8064: add missing clocks to the timer node
ARM: dts: qcom: apq8064-lg-nexus4-mako: Enable WiFi
ARM: dts: qcom: msm8226-motorola-falcon: specify vddio_disp output voltage
ARM: dts: qcom: msm8226-motorola-falcon: limit TPS65132 to 5.4V
ARM: dts: qcom: msm8226-motorola-falcon: add I2C clock frequencies
ARM: dts: qcom: msm8226-motorola-falcon: add clocks, power-domain to simpleFB
ARM: dts: qcom: ipq4019: Drop redundant CPU "clock-latency"
ARM: dts: qcom: sdx55/sdx65: Fix CPU power-domain-names
ARM: dts: qcom: msm8974: Use the header with DSI phy clock IDs
ARM: dts: qcom: msm8226: Use the header with DSI phy clock IDs
Link: https://lore.kernel.org/r/20250513214111.43401-1-andersson@kernel.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Qualcomm Arm64 DeviceTree updates for v6.16
The Snapdragon X Plus platform and related reference device is
introduced. Devicetree for the Xiaomi Redmi Note 8 is added.
Tsens and thermal zones are added for IPQ5332 and IPQ5424. IPQ6018 gains
1.2GHz and 1.5GHz CPU frequencies. The IPQ5424 gains MMC, LEDs and
buttons, while the IPQ9574 gains NSS clock controller and SPI NAND
support.
IPQ6018 SMEM is transitioned to be described directly in the
reserved-memory node.
Display and GPU are enabled in the QCM6490-based Fairphone FP5. On
QCS6490 Rb3Gen2 ADC channels for thermal profiling are added and
Bluetooth is enabled. The USB Type-C orientation GPIO is added on the
QCS6490 Rb3Gen2 and the vision mezzanine is described.
The Fairphone FP5 gains touchscreen and USB Type-C display support, and
the QCM6490 IDP board gains a required listed of protected clocks.
The camera subsystem in SC7280 is described and UFS is transitioned to
use operating points.
On MSM8916, MSM8919 and MSM8939, and devices on these platforms, the
UART pinctrl state is cleaned up.
The MSM8953 platform gains another UART and interconnects.
On SA8775P CTCU and ETR nodes are added, and the CPUfreq throttling
interrupts are added.
Samsung Galaxy S9 SM-G9600 gains a description of the MAX77705 used for
charging, fuel gauge, haptic, and LED, as well as the PMIC used for
display and touchscreen, which then is used to enable the touchscreen.
The LPG/PWM node is added to PM8937 and Xiaomi Redmi 5A gains display
backlight control.
Display and GPU are enabled for the Nothing Phone (1).
QCS615 platform gains command DB definition.
The QCS8300 platform gains description of more QUP instances, CPUfreq,
PCIe SMMU and the SPMI controller.
On SAR2130P PCIe EP device nodes are added.
On SDM630 missing resets are added for SDCC. Then on Fairphone FP3 modem
is enabled, and firmware-path are defined on ADSP and WCNSS.
The SDM845 RB3/DragonBoard845c and the QRB5165 RB5 has the sensors DSP
enabled, and the vision mezzanine on both gets their CMA configuration
cleaned up. Xiaomi Pocophone F1 gains touchscreen support.
On the SM7325 Nothing Phone (1), display, GPU, and camera EEPROMs are
described.
On SM8450 the PCIe endpoint controller is described.
For SM8550 OPP tables are described for PCIe and QUP. SM8750 gains RPMh
sleep stats.
SM8650 gians OSM L3 scaling and variety of OPP tables and missing
interconnect definitions. The thermal trip points for CPU cores and GPU
are raised in reliance on hardware throttling.
SM8650 is also transitioned to per-CPU interrupt partitions, in order to
properly describe the PMU interrupts. Missing Coresight ETE instances
are added.
On SM8750 the cluster idle states are corrected, then audio and compute
DSPs are introduced, together with the crypto and rng blocks. Modem
support is added and enabled on MTP and QRD devices.
On SC8280XP overlays are introduced for those running Linux at EL2 on
these devices. A few more temp-alarm instances are added for the PMICs.
On the X Elite platform GPU cooling and watchdog is introduced, together
with a number of smaller fixes. Dell XPS13 gains support for USB Type-C
display, the QCP gains WiFi/BT power sequence, and a few devices learns
about HBR3. The RTC support is enabled and regulators that are feeding
resources that should be always on is marked as such on a variety of
boards.
The Lenovo Thinkpad T14s DeviceTree is split in two, in order to
describe the LCD and OLED variants.
Missing properties for the crypto BAM is introduced on a variety of
platforms, taking care of a long standing error message in the kernel
log during boot.
DSI phy clock ids are transitioned to use identifiers from the PHY
header file and VBIF region size is corrected, across a large number of
platforms.
A couple of DWC3 quirks are added across a lot of platforms.
The arm32-for-6.15 pull request was accidentally merged into the
arm64-for-6.16 branch and this wasn't discovered until a significant
number of commits would have to be rebased. As such this is kept here as
well.
* tag 'qcom-arm64-for-6.16' of https://git.kernel.org/pub/scm/linux/kernel/git/qcom/linux: (308 commits)
arm64: dts: qcom: sdm845-xiaomi-beryllium-ebbg: introduce touchscreen support
arm64: dts: qcom: sdm845-xiaomi-beryllium-tianma: introduce touchscreen support
arm64: dts: qcom: sdm845-xiaomi-beryllium-common: add touchscreen related nodes
arm64: dts: qcom: qcs8300: add the pcie smmu node
arm64: dts: qcom: x1e80100-*: Drop useless DP3 compatible override
arm64: dts: qcom: msm8953: Add interconnects
arm64: dts: qcom: msm8953: Add uart_5
arm64: dts: qcom: sm8350: Use q6asm defines for reg
arm64: dts: qcom: sm7325-nothing-spacewar: Use q6asm defines for reg
arm64: dts: qcom: sdm850*: Use q6asm defines for reg
arm64: dts: qcom: sdm845*: Use q6asm defines for reg
arm64: dts: qcom: sc7280: Use q6asm defines for reg
arm64: dts: qcom: sc7180-acer-aspire1: Use q6asm defines for reg
arm64: dts: qcom: qrb5165-rb5: Use q6asm defines for reg
arm64: dts: qcom: msm8996*: Use q6asm defines for reg
arm64: dts: qcom: msm8953: Use q6asm defines for reg
arm64: dts: qcom: msm8916-modem-qdsp6: Use q6asm defines for reg
arm64: dts: qcom: apq8096-db820c: Use q6asm defines for reg
arm64: dts: qcom: qcm6490-fairphone-fp5: Hook up DisplayPort over USB-C
arm64: dts: qcom: qcm6490-fairphone-fp5: Add OCP96011 audio switch
...
Link: https://lore.kernel.org/r/20250511235241.15192-1-andersson@kernel.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
The rk3036 does contain a usb2phy, just until now it was just used
implicitly without additional configuration. As we now have the bits
in place for it getting actually controlled, add the necessary phy-node
to the GRF simple-mfd.
Enable the phy-ports in the same patch to not create bisectability
issues, as hooking up the phys to the usb controllers would create
probe deferrals until a board enables them. Doing everything in one
patch, solves that issue.
Only rk3036-kylin actually enabled the usb controllers, so is the only
board affected.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Link: https://lore.kernel.org/r/20250503201512.991277-4-heiko@sntech.de
Add support for Ultratronik's stm32mp157c fly board. This board embeds
a STM32MP157c SOC and 1GB of DDR3. Several connections are available on
this boards: 2*USB2.0, 1*USB2.0 MiniUSB, Debug UART, 1*UART, 1*USART,
SDcard, RJ45, ...
This patch enables basic support for a kernel boot - SD-card or eMMC.
Signed-off-by: Goran Rađenović <goran.radni@gmail.com>
Link: https://lore.kernel.org/r/20250508143818.2574558-5-goran.radni@gmail.com
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
