Verdin SPI_1 interface has a dedicated hardware controlled chip select
that is currently configured in the same pinctrl group as MISO/MOSI/CLK,
however it is possible that it can be used only as a standard GPIO be it
a chip select or not.
To maximize flexibility and avoid duplication in the carrier board dts
files move the SPI_1 CS in a dedicated pinctrl and also adds an
additional pinctrl to simplify using SPI_1 CS as a GPIO.
Signed-off-by: Joao Paulo Goncalves <joao.goncalves@toradex.com>
Signed-off-by: Francesco Dolcini <francesco.dolcini@toradex.com>
Link: https://lore.kernel.org/r/20231205184605.35225-2-francesco@dolcini.it
Signed-off-by: Nishanth Menon <nm@ti.com>
The DSS outputs DPI signals via its second video port (VP2). The DPI
output from DSS is 24 bits (RGB888) and is forwarded to an HDMI
transmitter (SIL9022) on the board.
Add pinmux for DSS DPI output and HDMI Interrupt.
Add DT nodes for SIL9022 HDMI transmitter (TX), and the HDMI connector
on the phyBOARD-Lyra.
Additionally, connect the output of DSS (VP2) with input of the HDMI TX,
and the output of HDMI TX to the input of the HDMI connector.
Signed-off-by: Garrett Giordano <ggiordano@phytec.com>
Reviewed-by: Wadim Egorov <w.egorov@phytec.de>
Link: https://lore.kernel.org/r/20231204222811.2344460-2-ggiordano@phytec.com
Signed-off-by: Nishanth Menon <nm@ti.com>
Communication between the R5F subsystem and Linux takes place using DMA
memory regions and mailboxes. Here we add DT nodes for the memory
regions and mailboxes to facilitate communication between the R5
clusters and Linux as remoteproc will fail to start if no memory
regions or mailboxes are provided.
Fixes: c48ac0efe6 ("arm64: dts: ti: Add support for phyBOARD-Electra-AM642")
Signed-off-by: Garrett Giordano <ggiordano@phytec.com>
Reviewed-by: Wadim Egorov <w.egorov@phytec.de>
Link: https://lore.kernel.org/r/20231204212304.1736306-1-ggiordano@phytec.com
Signed-off-by: Nishanth Menon <nm@ti.com>
Combined dtb builds are only useful for making sure that the overlay
applies cleanly on the base dtb.
So we move all such combined blobs under a `dtb- +=` section that is
only built when CONFIG_OF_ALL_DTBS is enabled.
Signed-off-by: Jai Luthra <j-luthra@ti.com>
Link: https://lore.kernel.org/r/20231201-csi_dts-v3-9-9f06f31080fe@ti.com
Signed-off-by: Nishanth Menon <nm@ti.com>
RPi v2 Camera (IMX219) is an 8MP camera that can be used with SK-AM62A
through the 22-pin CSI-RX connector.
Same overlay can be used across SK-AM62* boards that have a 15/22-pin
FFC connector, so we name it with the k3-am62x- prefix.
Signed-off-by: Jai Luthra <j-luthra@ti.com>
Link: https://lore.kernel.org/r/20231201-csi_dts-v3-8-9f06f31080fe@ti.com
Signed-off-by: Nishanth Menon <nm@ti.com>
Three different OV5640 modules are supported using the 15-pin FFC
connector on SK-AM62:
- Digilent PCam 5C
- ALINX AN5641
- TEVI-OV5640-*-RPI
The Digilent and ALINX modules supply a 12Mhz XCLK to the sensor, while
the TEVI module supplies a 24Mhz XCLK, thus requiring a separate
overlay.
These overlays can be used on other boards of the SK-AM62* family that
have a 15/22-pin FFC connector, so we name the overlays with the prefix
k3-am62x-.
Tested-by: Martyn Welch <martyn.welch@collabora.com>
Signed-off-by: Jai Luthra <j-luthra@ti.com>
Link: https://lore.kernel.org/r/20231201-csi_dts-v3-6-9f06f31080fe@ti.com
Signed-off-by: Nishanth Menon <nm@ti.com>
Three different OV5640 modules are supported using the FFC connector on
BeaglePlay:
- Digilent PCam 5C
- ALINX AN5641
- TEVI-OV5640-*-RPI
The Digilent and ALINX modules supply a 12Mhz XCLK to the sensor, while
the TEVI module supplies a 24Mhz XCLK, thus requiring a separate
overlay.
Reviewed-by: Andrew Davis <afd@ti.com>
Signed-off-by: Jai Luthra <j-luthra@ti.com>
Link: https://lore.kernel.org/r/20231201-csi_dts-v3-4-9f06f31080fe@ti.com
Signed-off-by: Nishanth Menon <nm@ti.com>
The AM652 is basically a AM654 but with 2 cores instead of 4. Add a
DTSI file for AM652 matching AM654 except this core difference.
This removes the need to remove the extra cores from AM654 manually
in DT files for boards that use the AM652 variant. Do that for the
IOT2050 boards here.
Signed-off-by: Andrew Davis <afd@ti.com>
Reviewed-by: Bryan Brattlof <bb@ti.com>
Link: https://lore.kernel.org/r/20231205162358.23904-1-afd@ti.com
Signed-off-by: Nishanth Menon <nm@ti.com>
The main_uart0 may not always be the console, but it will always be
the UART0 in MAIN domain. Name the pinmux node to match. This makes
it consistent with all other TI SoC based boards.
Signed-off-by: Andrew Davis <afd@ti.com>
Link: https://lore.kernel.org/r/20231127193602.151499-1-afd@ti.com
Signed-off-by: Nishanth Menon <nm@ti.com>
The Hot Plug Detect (HPD) signal for the HDMI display travels from the
on-board HDMI connector, through the IO Expander 1, and finally to the
main_gpio1 GPIO 23, of the SoC.
Add interrupt information for the IO Expander 1 (exp1) along with the
relevant pinmux.
Signed-off-by: Aradhya Bhatia <a-bhatia1@ti.com>
Reviewed-by: Jai Luthra <j-luthra@ti.com>
Link: https://lore.kernel.org/r/20231108191652.1118155-1-a-bhatia1@ti.com
Signed-off-by: Nishanth Menon <nm@ti.com>
On the AM62 platform we have no single 1:1 relation regarding index of
gpio and pin controller. Actually there are some linear ranges with
small holes inbetween. These ranges can be represented with the
gpio-ranges device tree property. They have been extracted manually
from the AM62x datasheet (Table 6-1. Pin Attributes).
Signed-off-by: Ronald Wahl <ronald.wahl@raritan.com>
Link: https://lore.kernel.org/r/20231127112657.2692103-1-rwahl@gmx.de
Signed-off-by: Nishanth Menon <nm@ti.com>
SDHCI nodes defined in the top-level AM64 SoC dtsi files are incomplete
and will not be functional unless they are extended.
As the attached SD/eMMC is only known about at the board integration level,
these nodes should only be enabled when provided with this information.
Disable the SDHCI nodes in the dtsi files and only enable the ones that
are actually pinned out on a given board.
Signed-off-by: Andrew Davis <afd@ti.com>
Link: https://lore.kernel.org/r/20231117163339.89952-2-afd@ti.com
Signed-off-by: Nishanth Menon <nm@ti.com>
SDHCI nodes defined in the top-level AM65 SoC dtsi files are incomplete
and will not be functional unless they are extended.
As the attached SD/eMMC is only known about at the board integration level,
these nodes should only be enabled when provided with this information.
Disable the SDHCI nodes in the dtsi files and only enable the ones that
are actually pinned out on a given board.
Signed-off-by: Andrew Davis <afd@ti.com>
Link: https://lore.kernel.org/r/20231117163339.89952-1-afd@ti.com
Signed-off-by: Nishanth Menon <nm@ti.com>
Like in other K3 SoCs the chipid register is inside the wakeup
configuration space. Move the chipid node under a new bus to
better represent this topology and match other similar SoCs.
Signed-off-by: Andrew Davis <afd@ti.com>
Link: https://lore.kernel.org/r/20231117140910.8747-2-afd@ti.com
Signed-off-by: Nishanth Menon <nm@ti.com>
Like in other K3 SoCs the chipid register is inside the wakeup
configuration space. Move the chipid node under a new bus to
better represent this topology and match other similar SoCs.
Signed-off-by: Andrew Davis <afd@ti.com>
Link: https://lore.kernel.org/r/20231117140910.8747-3-afd@ti.com
Signed-off-by: Nishanth Menon <nm@ti.com>
Like in other K3 SoCs the chipid register is inside the wakeup
configuration space. Move the chipid node under a new bus to
better represent this topology and match other similar SoCs.
Signed-off-by: Andrew Davis <afd@ti.com>
Link: https://lore.kernel.org/r/20231117140910.8747-5-afd@ti.com
Signed-off-by: Nishanth Menon <nm@ti.com>
Like in other K3 SoCs the chipid register is inside the wakeup
configuration space. Move the chipid node under a new bus to
better represent this topology and match other similar SoCs.
Signed-off-by: Andrew Davis <afd@ti.com>
Link: https://lore.kernel.org/r/20231117140910.8747-1-afd@ti.com
Signed-off-by: Nishanth Menon <nm@ti.com>
Like in other K3 SoCs the chipid register is inside the wakeup
configuration space. Move the chipid node under a new bus to
better represent this topology and match other similar SoCs.
Signed-off-by: Andrew Davis <afd@ti.com>
Link: https://lore.kernel.org/r/20231117140910.8747-4-afd@ti.com
Signed-off-by: Nishanth Menon <nm@ti.com>
Add multiple device tree nodes in order to support
runtime pinmuxing via debugfs.
All nodes are added to the pinctrl device node,
since they are now belonging to multiple interfaces now.
Note: Pinconf is also handled by debugfs-pinmux. This is possible since
pinconf and pinmux accessing the same 32-Bit register and setting the
function mask to 32-Bit allows writes to the whole register.
Signed-off-by: Benedikt Niedermayr <benedikt.niedermayr@siemens.com>
[Jan: fix node name style]
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Link: https://lore.kernel.org/r/3f90f3e521758622aa9b10f030cf0de1e68e77a4.1699087938.git.jan.kiszka@siemens.com
Signed-off-by: Nishanth Menon <nm@ti.com>
DSS irq trigger type is set to IRQ_TYPE_EDGE_RISING in the DT file, but
the TRM says it is level triggered.
For some reason triggering on rising edge results in double the amount
of expected interrupts, e.g. for normal page flipping test the number of
interrupts per second is 2 * fps. It is as if the IRQ triggers on both
edges. There are no other side effects to this issue than slightly
increased CPU & power consumption due to the extra interrupt.
Switching to IRQ_TYPE_LEVEL_HIGH is correct and fixes the issue, so
let's do that.
Fixes: fc539b90ed ("arm64: dts: ti: am654: Add DSS node")
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
Reviewed-by: Aradhya Bhatia <a-bhatia1@ti.com>
Link: https://lore.kernel.org/r/20231106-am65-dss-clk-edge-v1-1-4a959fec0e1e@ideasonboard.com
Signed-off-by: Nishanth Menon <nm@ti.com>
Pull probes fixes from Masami Hiramatsu:
- Documentation update: Add a note about argument and return value
fetching is the best effort because it depends on the type.
- objpool: Fix to make internal global variables static in
test_objpool.c.
- kprobes: Unify kprobes_exceptions_nofify() prototypes. There are the
same prototypes in asm/kprobes.h for some architectures, but some of
them are missing the prototype and it causes a warning. So move the
prototype into linux/kprobes.h.
- tracing: Fix to check the tracepoint event and return event at
parsing stage. The tracepoint event doesn't support %return but if
$retval exists, it will be converted to %return silently. This finds
that case and rejects it.
- tracing: Fix the order of the descriptions about the parameters of
__kprobe_event_gen_cmd_start() to be consistent with the argument
list of the function.
* tag 'probes-fixes-v6.7-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/trace/linux-trace:
tracing/kprobes: Fix the order of argument descriptions
tracing: fprobe-event: Fix to check tracepoint event and return
kprobes: unify kprobes_exceptions_nofify() prototypes
lib: test_objpool: make global variables static
Documentation: tracing: Add a note about argument and retval access
Pull arm64 fixes from Catalin Marinas:
"Mostly PMU fixes and a reworking of the pseudo-NMI disabling on broken
MediaTek firmware:
- Move the MediaTek GIC quirk handling from irqchip to core. Before
the merging window commit 44bd78dd2b ("irqchip/gic-v3: Disable
pseudo NMIs on MediaTek devices w/ firmware issues") temporarily
addressed this issue. Fixed now at a deeper level in the arch code
- Reject events meant for other PMUs in the CoreSight PMU driver,
otherwise some of the core PMU events would disappear
- Fix the Armv8 PMUv3 driver driver to not truncate 64-bit registers,
causing some events to be invisible
- Remove duplicate declaration of __arm64_sys##name following the
patch to avoid prototype warning for syscalls
- Typos in the elf_hwcap documentation"
* tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux:
arm64/syscall: Remove duplicate declaration
Revert "arm64: smp: avoid NMI IPIs with broken MediaTek FW"
arm64: Move MediaTek GIC quirk handling from irqchip to core
arm64/arm: arm_pmuv3: perf: Don't truncate 64-bit registers
perf: arm_cspmu: Reject events meant for other PMUs
Documentation/arm64: Fix typos in elf_hwcaps
Most architectures that support kprobes declare this function in their
own asm/kprobes.h header and provide an override, but some are missing
the prototype, which causes a warning for the __weak stub implementation:
kernel/kprobes.c:1865:12: error: no previous prototype for 'kprobe_exceptions_notify' [-Werror=missing-prototypes]
1865 | int __weak kprobe_exceptions_notify(struct notifier_block *self,
Move the prototype into linux/kprobes.h so it is visible to all
the definitions.
Link: https://lore.kernel.org/all/20231108125843.3806765-4-arnd@kernel.org/
Acked-by: Masami Hiramatsu (Google) <mhiramat@kernel.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Masami Hiramatsu (Google) <mhiramat@kernel.org>
Commit 6ac19f9651 ("arm64: avoid prototype warnings for syscalls")
added missing declarations to various syscall wrapper macros. It
however proved a little too zealous in __SYSCALL_DEFINEx(), as a
declaration for __arm64_sys##name was already present. A declaration
is required before the call to ALLOW_ERROR_INJECTION(), so keep
the original one and remove the new one.
Fixes: 6ac19f9651 ("arm64: avoid prototype warnings for syscalls")
Signed-off-by: Kevin Brodsky <kevin.brodsky@arm.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Link: https://lore.kernel.org/r/20231109141153.250046-1-kevin.brodsky@arm.com
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
In commit 44bd78dd2b ("irqchip/gic-v3: Disable pseudo NMIs on
MediaTek devices w/ firmware issues") we added a method for detecting
MediaTek devices with broken firmware and disabled pseudo-NMI. While
that worked, it didn't address the problem at a deep enough level.
The fundamental issue with this broken firmware is that it's not
saving and restoring several important GICR registers. The current
list is believed to be:
* GICR_NUM_IPRIORITYR
* GICR_CTLR
* GICR_ISPENDR0
* GICR_ISACTIVER0
* GICR_NSACR
Pseudo-NMI didn't work because it was the only thing (currently) in
the kernel that relied on the broken registers, so forcing pseudo-NMI
off was an effective fix. However, it could be observed that calling
system_uses_irq_prio_masking() on these systems still returned
"true". That caused confusion and led to the need for
commit a07a594152 ("arm64: smp: avoid NMI IPIs with broken MediaTek
FW"). It's worried that the incorrect value returned by
system_uses_irq_prio_masking() on these systems will continue to
confuse future developers.
Let's fix the issue a little more completely by disabling IRQ
priorities at a deeper level in the kernel. Once we do this we can
revert some of the other bits of code dealing with this quirk.
This includes a partial revert of commit 44bd78dd2b
("irqchip/gic-v3: Disable pseudo NMIs on MediaTek devices w/ firmware
issues"). This isn't a full revert because it leaves some of the
changes to the "quirks" structure around in case future code needs it.
Suggested-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Tested-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Acked-by: Mark Rutland <mark.rutland@arm.com>
Acked-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20231107072651.v2.1.Ide945748593cffd8ff0feb9ae22b795935b944d6@changeid
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Pull remoteproc updates from Bjorn Andersson:
"Support for controlling the second core in Mediatek's SCP dual-core
setup is introduced.
Support for audio, compute and modem DSPs on Qualcomm SM6375, and the
audio DSP in SC7180 are introduced. The peripheral NoC clock is
dropped from MSM8996 modem DSP, as this is handled through the
interconnect provider.
In the zynqmp driver the setup for TCM memory, and device address
translation thereof, when operating in lockstep mode is corrected.
A few bug fixes and cleanups are introduces across the ST and STM32
remoteproc drivers"
* tag 'rproc-v6.7' of git://git.kernel.org/pub/scm/linux/kernel/git/remoteproc/linux: (28 commits)
remoteproc: st: Fix sometimes uninitialized ret in st_rproc_probe()
remoteproc: st: Use device_get_match_data()
remoteproc: zynqmp: Change tcm address translation method
remoteproc: mediatek: Refactor single core check and fix retrocompatibility
remoteproc: qcom: q6v5-mss: Remove PNoC clock from 8996 MSS
dt-bindings: remoteproc: qcom,msm8996-mss-pil: Remove PNoC clock
dt-bindings: remoteproc: qcom,adsp: Remove AGGRE2 clock
remoteproc: qcom: pas: Add SM6375 MPSS
remoteproc: qcom: pas: Add SM6375 ADSP & CDSP
dt-bindings: remoteproc: qcom,sm6375-pas: Document remoteprocs
dt-bindings: remoteproc: pru: Add Interrupt property
remoteproc: qcom: pas: Add sc7180 adsp
dt-bindings: remoteproc: qcom: sc7180-pas: Add ADSP compatible
arm64: dts: mediatek: Update the node name of SCP rpmsg subnode
remoteproc: zynqmp: fix TCM carveouts in lockstep mode
remoteproc: mediatek: Refine ipi handler error message
remoteproc: mediatek: Report watchdog crash to all cores
remoteproc: mediatek: Handle MT8195 SCP core 1 watchdog timeout
remoteproc: mediatek: Setup MT8195 SCP core 1 SRAM offset
remoteproc: mediatek: Remove dependency of MT8195 SCP L2TCM power control on dual-core SCP
...
The driver used to truncate several 64-bit registers such as PMCEID[n]
registers used to describe whether architectural and microarchitectural
events in range 0x4000-0x401f exist. Due to discarding the bits, the
driver made the events invisible, even if they existed.
Moreover, PMCCFILTR and PMCR registers have additional bits in the upper
32 bits. This patch makes them available although they aren't currently
used. Finally, functions handling PMXEVCNTR and PMXEVTYPER registers are
removed as they not being used at all.
Fixes: df29ddf4f0 ("arm64: perf: Abstract system register accesses away")
Reported-by: Carl Worth <carl@os.amperecomputing.com>
Signed-off-by: Ilkka Koskinen <ilkka@os.amperecomputing.com>
Acked-by: Will Deacon <will@kernel.org>
Closes: https://lore.kernel.org/..
Reviewed-by: Anshuman Khandual <anshuman.khandual@arm.com>
Link: https://lore.kernel.org/r/20231102183012.1251410-1-ilkka@os.amperecomputing.com
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Pull Kbuild updates from Masahiro Yamada:
- Implement the binary search in modpost for faster symbol lookup
- Respect HOSTCC when linking host programs written in Rust
- Change the binrpm-pkg target to generate kernel-devel RPM package
- Fix endianness issues for tee and ishtp MODULE_DEVICE_TABLE
- Unify vdso_install rules
- Remove unused __memexit* annotations
- Eliminate stale whitelisting for __devinit/__devexit from modpost
- Enable dummy-tools to handle the -fpatchable-function-entry flag
- Add 'userldlibs' syntax
* tag 'kbuild-v6.7' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild: (30 commits)
kbuild: support 'userldlibs' syntax
kbuild: dummy-tools: pretend we understand -fpatchable-function-entry
kbuild: Correct missing architecture-specific hyphens
modpost: squash ALL_{INIT,EXIT}_TEXT_SECTIONS to ALL_TEXT_SECTIONS
modpost: merge sectioncheck table entries regarding init/exit sections
modpost: use ALL_INIT_SECTIONS for the section check from DATA_SECTIONS
modpost: disallow the combination of EXPORT_SYMBOL and __meminit*
modpost: remove EXIT_SECTIONS macro
modpost: remove MEM_INIT_SECTIONS macro
modpost: remove more symbol patterns from the section check whitelist
modpost: disallow *driver to reference .meminit* sections
linux/init: remove __memexit* annotations
modpost: remove ALL_EXIT_DATA_SECTIONS macro
kbuild: simplify cmd_ld_multi_m
kbuild: avoid too many execution of scripts/pahole-flags.sh
kbuild: remove ARCH_POSTLINK from module builds
kbuild: unify no-compiler-targets and no-sync-config-targets
kbuild: unify vdso_install rules
docs: kbuild: add INSTALL_DTBS_PATH
UML: remove unused cmd_vdso_install
...
Pull USB/Thunderbolt updates from Greg KH:
"Here is the "big" set of USB and Thunderbolt changes for 6.7-rc1.
Nothing really major in here, just lots of constant development for
new hardware. Included in here are:
- Thunderbolt (i.e. USB4) fixes for reported issues and support for
new hardware types and devices
- USB typec additions of new drivers and cleanups for some existing
ones
- xhci cleanups and expanded tracing support and some platform
specific updates
- USB "La Jolla Cove Adapter (LJCA)" support added, and the gpio,
spi, and i2c drivers for that type of device (all acked by the
respective subsystem maintainers.)
- lots of USB gadget driver updates and cleanups
- new USB dwc3 platforms supported, as well as other dwc3 fixes and
cleanups
- USB chipidea driver updates
- other smaller driver cleanups and additions, full details in the
shortlog
All of these have been in the linux-next tree for a while with no
reported problems"
* tag 'usb-6.7-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (167 commits)
usb: gadget: uvc: Add missing initialization of ssp config descriptor
usb: storage: set 1.50 as the lower bcdDevice for older "Super Top" compatibility
usb: raw-gadget: report suspend, resume, reset, and disconnect events
usb: raw-gadget: don't disable device if usb_ep_queue fails
usb: raw-gadget: properly handle interrupted requests
usb:cdnsp: remove TRB_FLUSH_ENDPOINT command
usb: gadget: aspeed_udc: Convert to platform remove callback returning void
dt-bindings: usb: fsa4480: Add compatible for OCP96011
usb: typec: fsa4480: Add support to swap SBU orientation
dt-bindings: usb: fsa4480: Add data-lanes property to endpoint
usb: typec: tcpm: Fix NULL pointer dereference in tcpm_pd_svdm()
Revert "dt-bindings: usb: Add bindings for multiport properties on DWC3 controller"
Revert "dt-bindings: usb: qcom,dwc3: Add bindings for SC8280 Multiport"
thunderbolt: Fix one kernel-doc comment
usb: gadget: f_ncm: Always set current gadget in ncm_bind()
usb: core: Remove duplicated check in usb_hub_create_port_device
usb: typec: tcpm: Add additional checks for contaminant
arm64: dts: rockchip: rk3588s: Add USB3 host controller
usb: dwc3: add optional PHY interface clocks
dt-bindings: usb: add rk3588 compatible to rockchip,dwc3
...
Pull tty and serial updates from Greg KH:
"Here is the big set of tty/serial driver changes for 6.7-rc1. Included
in here are:
- console/vgacon cleanups and removals from Arnd
- tty core and n_tty cleanups from Jiri
- lots of 8250 driver updates and cleanups
- sc16is7xx serial driver updates
- dt binding updates
- first set of port lock wrapers from Thomas for the printk fixes
coming in future releases
- other small serial and tty core cleanups and updates
All of these have been in linux-next for a while with no reported
issues"
* tag 'tty-6.7-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty: (193 commits)
serdev: Replace custom code with device_match_acpi_handle()
serdev: Simplify devm_serdev_device_open() function
serdev: Make use of device_set_node()
tty: n_gsm: add copyright Siemens Mobility GmbH
tty: n_gsm: fix race condition in status line change on dead connections
serial: core: Fix runtime PM handling for pending tx
vgacon: fix mips/sibyte build regression
dt-bindings: serial: drop unsupported samsung bindings
tty: serial: samsung: drop earlycon support for unsupported platforms
tty: 8250: Add note for PX-835
tty: 8250: Fix IS-200 PCI ID comment
tty: 8250: Add Brainboxes Oxford Semiconductor-based quirks
tty: 8250: Add support for Intashield IX cards
tty: 8250: Add support for additional Brainboxes PX cards
tty: 8250: Fix up PX-803/PX-857
tty: 8250: Fix port count of PX-257
tty: 8250: Add support for Intashield IS-100
tty: 8250: Add support for Brainboxes UP cards
tty: 8250: Add support for additional Brainboxes UC cards
tty: 8250: Remove UC-257 and UC-431
...
