Verdin SPI_1 interface has a dedicated hardware controlled chip select
that is currently configured in the same pinctrl group as MISO/MOSI/CLK,
however it is possible that it can be used only as a standard GPIO be it
a chip select or not.
To maximize flexibility and avoid duplication in the carrier board dts
files move the SPI_1 CS in a dedicated pinctrl and also adds an
additional pinctrl to simplify using SPI_1 CS as a GPIO.
Signed-off-by: Joao Paulo Goncalves <joao.goncalves@toradex.com>
Signed-off-by: Francesco Dolcini <francesco.dolcini@toradex.com>
Link: https://lore.kernel.org/r/20231205184605.35225-2-francesco@dolcini.it
Signed-off-by: Nishanth Menon <nm@ti.com>
The DSS outputs DPI signals via its second video port (VP2). The DPI
output from DSS is 24 bits (RGB888) and is forwarded to an HDMI
transmitter (SIL9022) on the board.
Add pinmux for DSS DPI output and HDMI Interrupt.
Add DT nodes for SIL9022 HDMI transmitter (TX), and the HDMI connector
on the phyBOARD-Lyra.
Additionally, connect the output of DSS (VP2) with input of the HDMI TX,
and the output of HDMI TX to the input of the HDMI connector.
Signed-off-by: Garrett Giordano <ggiordano@phytec.com>
Reviewed-by: Wadim Egorov <w.egorov@phytec.de>
Link: https://lore.kernel.org/r/20231204222811.2344460-2-ggiordano@phytec.com
Signed-off-by: Nishanth Menon <nm@ti.com>
Communication between the R5F subsystem and Linux takes place using DMA
memory regions and mailboxes. Here we add DT nodes for the memory
regions and mailboxes to facilitate communication between the R5
clusters and Linux as remoteproc will fail to start if no memory
regions or mailboxes are provided.
Fixes: c48ac0efe6 ("arm64: dts: ti: Add support for phyBOARD-Electra-AM642")
Signed-off-by: Garrett Giordano <ggiordano@phytec.com>
Reviewed-by: Wadim Egorov <w.egorov@phytec.de>
Link: https://lore.kernel.org/r/20231204212304.1736306-1-ggiordano@phytec.com
Signed-off-by: Nishanth Menon <nm@ti.com>
Combined dtb builds are only useful for making sure that the overlay
applies cleanly on the base dtb.
So we move all such combined blobs under a `dtb- +=` section that is
only built when CONFIG_OF_ALL_DTBS is enabled.
Signed-off-by: Jai Luthra <j-luthra@ti.com>
Link: https://lore.kernel.org/r/20231201-csi_dts-v3-9-9f06f31080fe@ti.com
Signed-off-by: Nishanth Menon <nm@ti.com>
RPi v2 Camera (IMX219) is an 8MP camera that can be used with SK-AM62A
through the 22-pin CSI-RX connector.
Same overlay can be used across SK-AM62* boards that have a 15/22-pin
FFC connector, so we name it with the k3-am62x- prefix.
Signed-off-by: Jai Luthra <j-luthra@ti.com>
Link: https://lore.kernel.org/r/20231201-csi_dts-v3-8-9f06f31080fe@ti.com
Signed-off-by: Nishanth Menon <nm@ti.com>
Three different OV5640 modules are supported using the 15-pin FFC
connector on SK-AM62:
- Digilent PCam 5C
- ALINX AN5641
- TEVI-OV5640-*-RPI
The Digilent and ALINX modules supply a 12Mhz XCLK to the sensor, while
the TEVI module supplies a 24Mhz XCLK, thus requiring a separate
overlay.
These overlays can be used on other boards of the SK-AM62* family that
have a 15/22-pin FFC connector, so we name the overlays with the prefix
k3-am62x-.
Tested-by: Martyn Welch <martyn.welch@collabora.com>
Signed-off-by: Jai Luthra <j-luthra@ti.com>
Link: https://lore.kernel.org/r/20231201-csi_dts-v3-6-9f06f31080fe@ti.com
Signed-off-by: Nishanth Menon <nm@ti.com>
Three different OV5640 modules are supported using the FFC connector on
BeaglePlay:
- Digilent PCam 5C
- ALINX AN5641
- TEVI-OV5640-*-RPI
The Digilent and ALINX modules supply a 12Mhz XCLK to the sensor, while
the TEVI module supplies a 24Mhz XCLK, thus requiring a separate
overlay.
Reviewed-by: Andrew Davis <afd@ti.com>
Signed-off-by: Jai Luthra <j-luthra@ti.com>
Link: https://lore.kernel.org/r/20231201-csi_dts-v3-4-9f06f31080fe@ti.com
Signed-off-by: Nishanth Menon <nm@ti.com>
The AM652 is basically a AM654 but with 2 cores instead of 4. Add a
DTSI file for AM652 matching AM654 except this core difference.
This removes the need to remove the extra cores from AM654 manually
in DT files for boards that use the AM652 variant. Do that for the
IOT2050 boards here.
Signed-off-by: Andrew Davis <afd@ti.com>
Reviewed-by: Bryan Brattlof <bb@ti.com>
Link: https://lore.kernel.org/r/20231205162358.23904-1-afd@ti.com
Signed-off-by: Nishanth Menon <nm@ti.com>
The main_uart0 may not always be the console, but it will always be
the UART0 in MAIN domain. Name the pinmux node to match. This makes
it consistent with all other TI SoC based boards.
Signed-off-by: Andrew Davis <afd@ti.com>
Link: https://lore.kernel.org/r/20231127193602.151499-1-afd@ti.com
Signed-off-by: Nishanth Menon <nm@ti.com>
The Hot Plug Detect (HPD) signal for the HDMI display travels from the
on-board HDMI connector, through the IO Expander 1, and finally to the
main_gpio1 GPIO 23, of the SoC.
Add interrupt information for the IO Expander 1 (exp1) along with the
relevant pinmux.
Signed-off-by: Aradhya Bhatia <a-bhatia1@ti.com>
Reviewed-by: Jai Luthra <j-luthra@ti.com>
Link: https://lore.kernel.org/r/20231108191652.1118155-1-a-bhatia1@ti.com
Signed-off-by: Nishanth Menon <nm@ti.com>
On the AM62 platform we have no single 1:1 relation regarding index of
gpio and pin controller. Actually there are some linear ranges with
small holes inbetween. These ranges can be represented with the
gpio-ranges device tree property. They have been extracted manually
from the AM62x datasheet (Table 6-1. Pin Attributes).
Signed-off-by: Ronald Wahl <ronald.wahl@raritan.com>
Link: https://lore.kernel.org/r/20231127112657.2692103-1-rwahl@gmx.de
Signed-off-by: Nishanth Menon <nm@ti.com>
SDHCI nodes defined in the top-level AM64 SoC dtsi files are incomplete
and will not be functional unless they are extended.
As the attached SD/eMMC is only known about at the board integration level,
these nodes should only be enabled when provided with this information.
Disable the SDHCI nodes in the dtsi files and only enable the ones that
are actually pinned out on a given board.
Signed-off-by: Andrew Davis <afd@ti.com>
Link: https://lore.kernel.org/r/20231117163339.89952-2-afd@ti.com
Signed-off-by: Nishanth Menon <nm@ti.com>
SDHCI nodes defined in the top-level AM65 SoC dtsi files are incomplete
and will not be functional unless they are extended.
As the attached SD/eMMC is only known about at the board integration level,
these nodes should only be enabled when provided with this information.
Disable the SDHCI nodes in the dtsi files and only enable the ones that
are actually pinned out on a given board.
Signed-off-by: Andrew Davis <afd@ti.com>
Link: https://lore.kernel.org/r/20231117163339.89952-1-afd@ti.com
Signed-off-by: Nishanth Menon <nm@ti.com>
Like in other K3 SoCs the chipid register is inside the wakeup
configuration space. Move the chipid node under a new bus to
better represent this topology and match other similar SoCs.
Signed-off-by: Andrew Davis <afd@ti.com>
Link: https://lore.kernel.org/r/20231117140910.8747-2-afd@ti.com
Signed-off-by: Nishanth Menon <nm@ti.com>
Like in other K3 SoCs the chipid register is inside the wakeup
configuration space. Move the chipid node under a new bus to
better represent this topology and match other similar SoCs.
Signed-off-by: Andrew Davis <afd@ti.com>
Link: https://lore.kernel.org/r/20231117140910.8747-3-afd@ti.com
Signed-off-by: Nishanth Menon <nm@ti.com>
Like in other K3 SoCs the chipid register is inside the wakeup
configuration space. Move the chipid node under a new bus to
better represent this topology and match other similar SoCs.
Signed-off-by: Andrew Davis <afd@ti.com>
Link: https://lore.kernel.org/r/20231117140910.8747-5-afd@ti.com
Signed-off-by: Nishanth Menon <nm@ti.com>
Like in other K3 SoCs the chipid register is inside the wakeup
configuration space. Move the chipid node under a new bus to
better represent this topology and match other similar SoCs.
Signed-off-by: Andrew Davis <afd@ti.com>
Link: https://lore.kernel.org/r/20231117140910.8747-1-afd@ti.com
Signed-off-by: Nishanth Menon <nm@ti.com>
Like in other K3 SoCs the chipid register is inside the wakeup
configuration space. Move the chipid node under a new bus to
better represent this topology and match other similar SoCs.
Signed-off-by: Andrew Davis <afd@ti.com>
Link: https://lore.kernel.org/r/20231117140910.8747-4-afd@ti.com
Signed-off-by: Nishanth Menon <nm@ti.com>
Add multiple device tree nodes in order to support
runtime pinmuxing via debugfs.
All nodes are added to the pinctrl device node,
since they are now belonging to multiple interfaces now.
Note: Pinconf is also handled by debugfs-pinmux. This is possible since
pinconf and pinmux accessing the same 32-Bit register and setting the
function mask to 32-Bit allows writes to the whole register.
Signed-off-by: Benedikt Niedermayr <benedikt.niedermayr@siemens.com>
[Jan: fix node name style]
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Link: https://lore.kernel.org/r/3f90f3e521758622aa9b10f030cf0de1e68e77a4.1699087938.git.jan.kiszka@siemens.com
Signed-off-by: Nishanth Menon <nm@ti.com>
DSS irq trigger type is set to IRQ_TYPE_EDGE_RISING in the DT file, but
the TRM says it is level triggered.
For some reason triggering on rising edge results in double the amount
of expected interrupts, e.g. for normal page flipping test the number of
interrupts per second is 2 * fps. It is as if the IRQ triggers on both
edges. There are no other side effects to this issue than slightly
increased CPU & power consumption due to the extra interrupt.
Switching to IRQ_TYPE_LEVEL_HIGH is correct and fixes the issue, so
let's do that.
Fixes: fc539b90ed ("arm64: dts: ti: am654: Add DSS node")
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
Reviewed-by: Aradhya Bhatia <a-bhatia1@ti.com>
Link: https://lore.kernel.org/r/20231106-am65-dss-clk-edge-v1-1-4a959fec0e1e@ideasonboard.com
Signed-off-by: Nishanth Menon <nm@ti.com>
Pull parisc architecture fixes from Helge Deller:
- Include the upper 5 address bits when inserting TLB entries on a
64-bit kernel.
On physical machines those are ignored, but in qemu it's nice to have
them included and to be correct.
- Stop the 64-bit kernel and show a warning if someone tries to boot on
a machine with a 32-bit CPU
- Fix a "no previous prototype" warning in parport-gsc
* tag 'parisc-for-6.7-rc1-2' of git://git.kernel.org/pub/scm/linux/kernel/git/deller/parisc-linux:
parisc: Prevent booting 64-bit kernels on PA1.x machines
parport: gsc: mark init function static
parisc/pgtable: Do not drop upper 5 address bits of physical address
Pull LoongArch updates from Huacai Chen:
- support PREEMPT_DYNAMIC with static keys
- relax memory ordering for atomic operations
- support BPF CPU v4 instructions for LoongArch
- some build and runtime warning fixes
* tag 'loongarch-6.7' of git://git.kernel.org/pub/scm/linux/kernel/git/chenhuacai/linux-loongson:
selftests/bpf: Enable cpu v4 tests for LoongArch
LoongArch: BPF: Support signed mod instructions
LoongArch: BPF: Support signed div instructions
LoongArch: BPF: Support 32-bit offset jmp instructions
LoongArch: BPF: Support unconditional bswap instructions
LoongArch: BPF: Support sign-extension mov instructions
LoongArch: BPF: Support sign-extension load instructions
LoongArch: Add more instruction opcodes and emit_* helpers
LoongArch/smp: Call rcutree_report_cpu_starting() earlier
LoongArch: Relax memory ordering for atomic operations
LoongArch: Mark __percpu functions as always inline
LoongArch: Disable module from accessing external data directly
LoongArch: Support PREEMPT_DYNAMIC with static keys
Pull powerpc fixes from Michael Ellerman:
- Finish a refactor of pgprot_framebuffer() which dependend
on some changes that were merged via the drm tree
- Fix some kernel-doc warnings to quieten the bots
Thanks to Nathan Lynch and Thomas Zimmermann.
* tag 'powerpc-6.7-2' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux:
powerpc/rtas: Fix ppc_rtas_rmo_buf_show() kernel-doc
powerpc/pseries/rtas-work-area: Fix rtas_work_area_reserve_arena() kernel-doc
powerpc/fb: Call internal __phys_mem_access_prot() in fbdev code
powerpc: Remove file parameter from phys_mem_access_prot()
powerpc/machdep: Remove trailing whitespaces
Pull smb client fixes from Steve French:
- ctime caching fix (for setxattr)
- encryption fix
- DNS resolver mount fix
- debugging improvements
- multichannel fixes including cases where server stops or starts
supporting multichannel after mount
- reconnect fix
- minor cleanups
* tag '6.7-rc-smb3-client-fixes-part2' of git://git.samba.org/sfrench/cifs-2.6:
cifs: update internal module version number for cifs.ko
cifs: handle when server stops supporting multichannel
cifs: handle when server starts supporting multichannel
Missing field not being returned in ioctl CIFS_IOC_GET_MNT_INFO
smb3: allow dumping session and tcon id to improve stats analysis and debugging
smb: client: fix mount when dns_resolver key is not available
smb3: fix caching of ctime on setxattr
smb3: minor cleanup of session handling code
cifs: reconnect work should have reference on server struct
cifs: do not pass cifs_sb when trying to add channels
cifs: account for primary channel in the interface list
cifs: distribute channels across interfaces based on speed
cifs: handle cases where a channel is closed
smb3: more minor cleanups for session handling routines
smb3: minor RDMA cleanup
cifs: Fix encryption of cleared, but unset rq_iter data buffers
Pull probes fixes from Masami Hiramatsu:
- Documentation update: Add a note about argument and return value
fetching is the best effort because it depends on the type.
- objpool: Fix to make internal global variables static in
test_objpool.c.
- kprobes: Unify kprobes_exceptions_nofify() prototypes. There are the
same prototypes in asm/kprobes.h for some architectures, but some of
them are missing the prototype and it causes a warning. So move the
prototype into linux/kprobes.h.
- tracing: Fix to check the tracepoint event and return event at
parsing stage. The tracepoint event doesn't support %return but if
$retval exists, it will be converted to %return silently. This finds
that case and rejects it.
- tracing: Fix the order of the descriptions about the parameters of
__kprobe_event_gen_cmd_start() to be consistent with the argument
list of the function.
* tag 'probes-fixes-v6.7-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/trace/linux-trace:
tracing/kprobes: Fix the order of argument descriptions
tracing: fprobe-event: Fix to check tracepoint event and return
kprobes: unify kprobes_exceptions_nofify() prototypes
lib: test_objpool: make global variables static
Documentation: tracing: Add a note about argument and retval access
Pull fbdev fixes and cleanups from Helge Deller:
- fix double free and resource leaks in imsttfb
- lots of remove callback cleanups and section mismatch fixes in
omapfb, amifb and atmel_lcdfb
- error code fix and memparse simplification in omapfb
* tag 'fbdev-for-6.7-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/deller/linux-fbdev: (31 commits)
fbdev: fsl-diu-fb: mark wr_reg_wa() static
fbdev: amifb: Convert to platform remove callback returning void
fbdev: amifb: Mark driver struct with __refdata to prevent section mismatch warning
fbdev: hyperv_fb: fix uninitialized local variable use
fbdev: omapfb/tpd12s015: Convert to platform remove callback returning void
fbdev: omapfb/tfp410: Convert to platform remove callback returning void
fbdev: omapfb/sharp-ls037v7dw01: Convert to platform remove callback returning void
fbdev: omapfb/opa362: Convert to platform remove callback returning void
fbdev: omapfb/hdmi: Convert to platform remove callback returning void
fbdev: omapfb/dvi: Convert to platform remove callback returning void
fbdev: omapfb/dsi-cm: Convert to platform remove callback returning void
fbdev: omapfb/dpi: Convert to platform remove callback returning void
fbdev: omapfb/analog-tv: Convert to platform remove callback returning void
fbdev: atmel_lcdfb: Convert to platform remove callback returning void
fbdev: omapfb/tpd12s015: Don't put .remove() in .exit.text and drop suppress_bind_attrs
fbdev: omapfb/tfp410: Don't put .remove() in .exit.text and drop suppress_bind_attrs
fbdev: omapfb/sharp-ls037v7dw01: Don't put .remove() in .exit.text and drop suppress_bind_attrs
fbdev: omapfb/opa362: Don't put .remove() in .exit.text and drop suppress_bind_attrs
fbdev: omapfb/hdmi: Don't put .remove() in .exit.text and drop suppress_bind_attrs
fbdev: omapfb/dvi: Don't put .remove() in .exit.text and drop suppress_bind_attrs
...
Pull drm fixes from Daniel Vetter:
"Dave's VPN to the big machine died, so it's on me to do fixes pr this
and next week while everyone else is at plumbers.
- big pile of amd fixes, but mostly for hw support newly added in 6.7
- i915 fixes, mostly minor things
- qxl memory leak fix
- vc4 uaf fix in mock helpers
- syncobj fix for DRM_SYNCOBJ_WAIT_FLAGS_WAIT_AVAILABLE"
* tag 'drm-next-2023-11-10' of git://anongit.freedesktop.org/drm/drm: (78 commits)
drm/amdgpu: fix error handling in amdgpu_vm_init
drm/amdgpu: Fix possible null pointer dereference
drm/amdgpu: move UVD and VCE sched entity init after sched init
drm/amdgpu: move kfd_resume before the ip late init
drm/amd: Explicitly check for GFXOFF to be enabled for s0ix
drm/amdgpu: Change WREG32_RLC to WREG32_SOC15_RLC where inst != 0 (v2)
drm/amdgpu: Use correct KIQ MEC engine for gfx9.4.3 (v5)
drm/amdgpu: add smu v13.0.6 pcs xgmi ras error query support
drm/amdgpu: fix software pci_unplug on some chips
drm/amd/display: remove duplicated argument
drm/amdgpu: correct mca debugfs dump reg list
drm/amdgpu: correct acclerator check architecutre dump
drm/amdgpu: add pcs xgmi v6.4.0 ras support
drm/amdgpu: Change extended-scope MTYPE on GC 9.4.3
drm/amdgpu: disable smu v13.0.6 mca debug mode by default
drm/amdgpu: Support multiple error query modes
drm/amdgpu: refine smu v13.0.6 mca dump driver
drm/amdgpu: Do not program PF-only regs in hdp_v4_0.c under SRIOV (v2)
drm/amdgpu: Skip PCTL0_MMHUB_DEEPSLEEP_IB write in jpegv4.0.3 under SRIOV
drm: amd: Resolve Sphinx unexpected indentation warning
...
