If sdhci use PIO mode, and use mmc_send_tuning() to send the tuning
command, system will stuck because of the storm irq of sdhci. For PIO mode,
use mmc_send_tuning(), it will trigger buffer_read_ready interrupt and data
transfer complete interrupt. In current code logic, it will directly
return in sdhci_data_irq, can not call the sdhci_transfer_pio(). So the
buffer_read_ready interrupt storm happen. So for standard tuning method,
need to exclude this case.
Signed-off-by: Haibo Chen <haibo.chen@nxp.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/1628858041-1911-1-git-send-email-haibo.chen@nxp.com
[Ulf: Dropped redundant parenthesis in an expression]
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Depending on the DMA driver being used, the struct dma_slave_config may
need to be initialized to zero for the unused data.
For example, we have three DMA drivers using src_port_window_size and
dst_port_window_size. If these are left uninitialized, it can cause DMA
failures.
For moxart, this is probably not currently an issue but is still good to
fix though.
Fixes: 1b66e94e6b ("mmc: moxart: Add MOXA ART SD/MMC driver")
Cc: Jonas Jensen <jonas.jensen@gmail.com>
Cc: Vinod Koul <vkoul@kernel.org>
Cc: Peter Ujfalusi <peter.ujfalusi@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Link: https://lore.kernel.org/r/20210810081644.19353-3-tony@atomide.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
For unexplained reasons, the prescaler register for this device needs to
be cleared (set to 1) while performing a data read or else the command
will hang. This does not appear to affect the real clock rate sent out
on the bus, so I assume it's purely to work around a hardware bug.
During normal operation, the prescaler is already set to 1, so nothing
needs to be done. However, in "initial mode" (which is used for sub-MHz
clock speeds, like the core sets while enumerating cards), it's set to
128 and so we need to reset it during data reads. We currently fail to
do this for long reads.
This has no functional affect on the driver's operation currently
written, as the MMC core always sets a clock above 1MHz before
attempting any long reads. However, the core could conceivably set any
clock speed at any time and the driver should still work, so I think
this fix is worthwhile.
I personally encountered this issue while performing data recovery on an
external chip. My connections had poor signal integrity, so I modified
the core code to reduce the clock speed. Without this change, I saw the
card enumerate but was unable to actually read any data.
Writes don't seem to work in the situation described above even with
this change (and even if the workaround is extended to encompass data
write commands). I was not able to find a way to get them working.
Signed-off-by: Thomas Hebb <tommyhebb@gmail.com>
Link: https://lore.kernel.org/r/2fef280d8409ab0100c26c6ac7050227defd098d.1627818365.git.tommyhebb@gmail.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
CIS tuples in the range 0x80-0x8F are reserved for vendors. Some devices
have tuples in this range which get warned about every boot. Since this
is normal behavior, don't print these tuples unless debug is enabled.
Unfortunately, we cannot use a variable for the format string since it
gets pasted by pr_*_ratelimited.
Signed-off-by: Sean Anderson <sean.anderson@seco.com>
Link: https://lore.kernel.org/r/20210726163654.1110969-1-sean.anderson@seco.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Make 'struct mmc_request' contain a pointer to the request's
'struct bio_crypt_ctx' directly, instead of extracting a 32-bit DUN from
it which is a cqhci-crypto specific detail.
This keeps the cqhci crypto specific details in the cqhci module, and it
makes mmc_core and mmc_block ready for MMC crypto hardware that accepts
the DUN and/or key in a way that is more flexible than that which will
be specified by the eMMC v5.2 standard. Exynos SoCs are an example of
such hardware, as their inline encryption hardware takes keys directly
(it has no concept of keyslots) and supports 128-bit DUNs.
Note that the 32-bit DUN length specified by the standard is very
restrictive, so it is likely that more hardware will support longer DUNs
despite it not following the standard. Thus, limiting the scope of the
32-bit DUN assumption to the place that actually needs it is warranted.
Signed-off-by: Eric Biggers <ebiggers@google.com>
Link: https://lore.kernel.org/r/20210721154738.3966463-1-ebiggers@kernel.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
When mmc_blk_card_busy() calls card_busy_detect() to poll for the card's
state with CMD13, this is done without any delays in between the commands
being sent.
Rather than fixing card_busy_detect() in this regards, let's instead
convert into using the common __mmc_poll_for_busy(), which also helps us to
avoid open-coding.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Reviewed-by: Shawn Lin <shawn.lin@rock-chips.com>
Link: https://lore.kernel.org/r/20210702134229.357717-4-ulf.hansson@linaro.org
When __mmc_blk_ioctl_cmd() calls card_busy_detect() to verify that the
card's states moves back into transfer state, the polling with CMD13 is
done without any delays in between the commands being sent.
Rather than fixing card_busy_detect() in this regards, let's instead
convert into using the common mmc_poll_for_busy(), which also helps us to
avoid open-coding.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Reviewed-by: Shawn Lin <shawn.lin@rock-chips.com>
Link: https://lore.kernel.org/r/20210702134229.357717-3-ulf.hansson@linaro.org
When mmc_blk_fix_state() sends a CMD12 to try to move the card into the
transfer state, it calls card_busy_detect() to poll for the card's state
with CMD13. This is done without any delays in between the commands being
sent.
Rather than fixing card_busy_detect() in this regards, let's instead
convert into using the common mmc_poll_for_busy(), which also helps us to
avoid open-coding.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Reviewed-by: Shawn Lin <shawn.lin@rock-chips.com>
Link: https://lore.kernel.org/r/20210702134229.357717-2-ulf.hansson@linaro.org
This driver has had problems when handling data errors. Add fault
injection support so that the abort handling can be easily triggered and
regression-tested. A hrtimer is used to indicate a data CRC error at
various points during the data transfer.
Note that for the recent problem with hangs in the case of some data CRC
errors, a udelay(10) inserted at the start of send_stop_abort() greatly
helped in triggering the error, but I've not included this as part of
the fault injection support since it seemed too specific.
Signed-off-by: Vincent Whitchurch <vincent.whitchurch@axis.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Link: https://lore.kernel.org/r/20210701080534.23138-1-vincent.whitchurch@axis.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Pull powerpc fixes from Michael Ellerman:
- Fix random crashes on some 32-bit CPUs by adding isync() after
locking/unlocking KUEP
- Fix intermittent crashes when loading modules with strict module RWX
- Fix a section mismatch introduce by a previous fix.
Thanks to Christophe Leroy, Fabiano Rosas, Laurent Vivier, Murilo
Opsfelder Araújo, Nathan Chancellor, and Stan Johnson.
h# -----BEGIN PGP SIGNATURE-----
* tag 'powerpc-5.14-6' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux:
powerpc/mm: Fix set_memory_*() against concurrent accesses
powerpc/32s: Fix random crashes by adding isync() after locking/unlocking KUEP
powerpc/xive: Do not mark xive_request_ipi() as __init
Pull clk driver fixes from Stephen Boyd:
- Make the regulator state match the GDSC power domain state at boot on
Qualcomm SoCs so that the regulator isn't turned off inadvertently.
- Fix earlycon on i.MX6Q SoCs
* tag 'clk-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux:
clk: qcom: gdsc: Ensure regulator init state matches GDSC state
clk: imx6q: fix uart earlycon unwork
Pull char/misc driver fixes from Greg KH:
"Here are some small driver fixes for 5.14-rc7.
They consist of:
- revert for an interconnect patch that was found to have problems
- ipack tpci200 driver fixes for reported problems
- slimbus messaging and ngd fixes for reported problems
All are small and have been in linux-next for a while with no reported
issues"
* tag 'char-misc-5.14-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc:
ipack: tpci200: fix memory leak in the tpci200_register
ipack: tpci200: fix many double free issues in tpci200_pci_probe
slimbus: ngd: reset dma setup during runtime pm
slimbus: ngd: set correct device for pm
slimbus: messaging: check for valid transaction id
slimbus: messaging: start transaction ids from 1 instead of zero
Revert "interconnect: qcom: icc-rpmh: Add BCMs to commit list in pre_aggregate"
Pull USB fix from Greg KH:
"Here is a single USB typec tcpm fix for a reported problem for
5.14-rc7. It showed up in 5.13 and resolves an issue that Hans found.
It has been in linux-next this week with no reported problems"
* tag 'usb-5.14-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb:
usb: typec: tcpm: Fix VDMs sometimes not being forwarded to alt-mode drivers
Pull RISC-V fixes from Palmer Dabbelt:
- fix the sifive-l2-cache device tree bindings for json-schema
compatibility. This does not change the intended behavior of the
binding.
- avoid improperly freeing necessary resources during early boot.
* tag 'riscv-for-linus-5.14-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/riscv/linux:
riscv: Fix a number of free'd resources in init_resources()
dt-bindings: sifive-l2-cache: Fix 'select' matching
Pull s390 fix from Vasily Gorbik:
- fix use after free of zpci_dev in pci code
* tag 's390-5.14-5' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux:
s390/pci: fix use after free of zpci_dev
Pull mandatory file locking deprecation warning from Jeff Layton:
"As discussed on the list, this patch just adds a new warning for folks
who still have mandatory locking enabled and actually mount with '-o
mand'. I'd like to get this in for v5.14 so we can push this out into
stable kernels and hopefully reach folks who have mounts with -o mand.
For now, I'm operating under the assumption that we'll fully remove
this support in v5.15, but we can move that out if any legitimate
users of this facility speak up between now and then"
* tag 'locks-v5.14' of git://git.kernel.org/pub/scm/linux/kernel/git/jlayton/linux:
fs: warn about impending deprecation of mandatory locks
Pull block fixes from Jens Axboe:
"Three fixes from Ming Lei that should go into 5.14:
- Fix for a kernel panic when iterating over tags for some cases
where a flush request is present, a regression in this cycle.
- Request timeout fix
- Fix flush request checking"
* tag 'block-5.14-2021-08-20' of git://git.kernel.dk/linux-block:
blk-mq: fix is_flush_rq
blk-mq: fix kernel panic during iterating over flush request
blk-mq: don't grab rq's refcount in blk_mq_check_expired()
Pull io_uring fixes from Jens Axboe:
"A few small fixes that should go into this release:
- Fix never re-assigning an initial error value for io_uring_enter()
for SQPOLL, if asked to do nothing
- Fix xa_alloc_cycle() return value checking, for cases where we have
wrapped around
- Fix for a ctx pin issue introduced in this cycle (Pavel)"
* tag 'io_uring-5.14-2021-08-20' of git://git.kernel.dk/linux-block:
io_uring: fix xa_alloc_cycle() error return value check
io_uring: pin ctx on fallback execution
io_uring: only assign io_uring_enter() SQPOLL error in actual error case
We've had CONFIG_MANDATORY_FILE_LOCKING since 2015 and a lot of distros
have disabled it. Warn the stragglers that still use "-o mand" that
we'll be dropping support for that mount option.
Cc: stable@vger.kernel.org
Signed-off-by: Jeff Layton <jlayton@kernel.org>
We currently check for ret != 0 to indicate error, but '1' is a valid
return and just indicates that the allocation succeeded with a wrap.
Correct the check to be for < 0, like it was before the xarray
conversion.
Cc: stable@vger.kernel.org
Fixes: 61cf93700f ("io_uring: Convert personality_idr to XArray")
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Pull ACPI fixes from Rafael Wysocki:
"These fix two mistakes in new code.
Specifics:
- Prevent confusing messages from being printed if the PRMT table is
not present or there are no PRM modules (Aubrey Li).
- Fix the handling of suspend-to-idle entry and exit in the case when
the Microsoft UUID is used with the Low-Power S0 Idle _DSM
interface (Mario Limonciello)"
* tag 'acpi-5.14-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
ACPI: PM: s2idle: Invert Microsoft UUID entry and exit
ACPI: PRM: Deal with table not present or no module found
Pull power management fixes from Rafael Wysocki:
"These fix some issues in the ARM cpufreq drivers and in the operating
performance points (OPP) framework.
Specifics:
- Fix useless WARN() in the OPP core and prevent a noisy warning
from being printed by OPP _put functions (Dmitry Osipenko).
- Fix error path when allocation failed in the arm_scmi cpufreq
driver (Lukasz Luba).
- Blacklist Qualcomm sc8180x and Qualcomm sm8150 in
cpufreq-dt-platdev (Bjorn Andersson, Thara Gopinath).
- Forbid cpufreq for 1.2 GHz variant in the armada-37xx cpufreq
driver (Marek Behún)"
* tag 'pm-5.14-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
opp: Drop empty-table checks from _put functions
cpufreq: armada-37xx: forbid cpufreq for 1.2 GHz variant
cpufreq: blocklist Qualcomm sm8150 in cpufreq-dt-platdev
cpufreq: arm_scmi: Fix error path when allocation failed
opp: remove WARN when no valid OPPs remain
cpufreq: blacklist Qualcomm sc8180x in cpufreq-dt-platdev
Pull drm fixes from Dave Airlie:
"Regularly scheduled fixes. The ttm one solves a problem of GPU drivers
failing to load if debugfs is off in Kconfig, otherwise the i915 and
mediatek, and amdgpu fixes all fairly normal.
Nouveau has a couple of display fixes, but it has a fix for a
longstanding race condition in it's memory manager code, and the fix
mostly removes some code that wasn't working properly and has no
userspace users. This fix makes the diffstat kinda larger but in a
good (negative line-count) way.
core:
- fix drm_wait_vblank uapi copying bug
ttm:
- fix debugfs init when debugfs is off
amdgpu:
- vega10 SMU workload fix
- DCN VM fix
- DCN 3.01 watermark fix
amdkfd:
- SVM fix
nouveau:
- ampere display fixes
- remove MM misfeature to fix a longstanding race condition
i915:
- tweaked display workaround for all PCHs
- eDP MSO pipe sanity for ADL-P fix
- remove unused symbol export
mediatek:
- AAL output size setting
- Delete component in remove function"
* tag 'drm-fixes-2021-08-20-3' of git://anongit.freedesktop.org/drm/drm:
drm/amd/display: Use DCN30 watermark calc for DCN301
drm/i915/dp: remove superfluous EXPORT_SYMBOL()
drm/i915/edp: fix eDP MSO pipe sanity checks for ADL-P
drm/i915: Tweaked Wa_14010685332 for all PCHs
drm/nouveau: rip out nvkm_client.super
drm/nouveau: block a bunch of classes from userspace
drm/nouveau/fifo/nv50-: rip out dma channels
drm/nouveau/kms/nv50: workaround EFI GOP window channel format differences
drm/nouveau/disp: power down unused DP links during init
drm/nouveau: recognise GA107
drm: Copy drm_wait_vblank to user before returning
drm/amd/display: Ensure DCN save after VM setup
drm/amdkfd: fix random KFDSVMRangeTest.SetGetAttributesTest test failure
drm/amd/pm: change the workload type for some cards
Revert "drm/amd/pm: fix workload mismatch on vega10"
drm: ttm: Don't bail from ttm_global_init if debugfs_create_dir fails
drm/mediatek: Add component_del in OVL and COLOR remove function
drm/mediatek: Add AAL output size configuration
Pull PCI fixes from Bjorn Helgaas:
- Add Rahul Tanwar as Intel LGM Gateway PCIe maintainer (Rahul Tanwar)
- Add Jim Quinlan et al as Broadcom STB PCIe maintainers (Jim Quinlan)
- Increase D3hot-to-D0 delay for AMD Renoir/Cezanne XHCI (Marcin
Bachry)
- Correct iomem_get_mapping() usage for legacy_mem sysfs (Krzysztof
Wilczyński)
* tag 'pci-v5.14-fixes-2' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci:
PCI/sysfs: Use correct variable for the legacy_mem sysfs object
PCI: Increase D3 delay for AMD Renoir/Cezanne XHCI
MAINTAINERS: Add Jim Quinlan et al as Broadcom STB PCIe maintainers
MAINTAINERS: Add Rahul Tanwar as Intel LGM Gateway PCIe maintainer
