On s390 allyesconfig, there is this build error
rtsx_pcr.c:1084:13: error: 'rtsx_pm_power_saving'
defined but not used
1084 | static void rtsx_pm_power_saving(struct rtsx_pcr *pcr)
| ^~~~~~~~~~~~~~~~~~~~
rtsx_pm_power_saving() is only used by rtsx_pci_runtime_idle()
which is conditional on CONFIG_PM. So conditionally build
rtsx_pm_power_saving() and the similar
rtsx_comm_pm_power_saving() and rtsx_enable_aspm().
Signed-off-by: Tom Rix <trix@redhat.com>
Link: https://lore.kernel.org/r/20220213171907.2786442-1-trix@redhat.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
AOSP's `netd` process fails to start on Android S:
E ClatdController: getClatEgress4MapFd() failure: Operation not permitted
I netd : Initializing ClatdController: 410us
E netd : Failed to start trafficcontroller: (Status[code: 1, msg: "Pinned map not accessible or does not exist: (/sys/fs/bpf/map_netd_cookie_tag_map): Operation not permitted"])
E netd : CRITICAL: sleeping 60 seconds, netd exiting with failure, crash loop likely!
And on Android R:
I ClatdController: 4.9+ kernel and device shipped with P - clat ebpf might work.
E ClatdController: getClatEgressMapFd() failure: Operation not permitted
I netd : Initializing ClatdController: 1409us
E netd : Failed to start trafficcontroller: (Status[code: 1, msg: "Pinned map not accessible or does not exist: (/sys/fs/bpf/map_netd_cookie_tag_map): Operation not permitted"])
These permission issues are caused by 08389d8882 ("bpf: Add kconfig
knob for disabling unpriv bpf by default") because AOSP does not provide
netd the `SYS_ADMIN` capability, and also has no userspace support for
the `BPF` capability yet.
Cc: Amit Pundir <amit.pundir@linaro.org>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Suggested-by: John Stultz <john.stultz@linaro.org>
[John suggested this in https://linaro.atlassian.net/browse/ACK-107?focusedCommentId=117382]
Signed-off-by: Marijn Suijten <marijn.suijten@somainline.org>
Link: https://lore.kernel.org/r/20220202100528.190794-2-marijn.suijten@somainline.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
While in this particular case (*) it would not be an issue,
the pattern itself is bad and error prone in case somebody
blindly copies to their code.
Don't cast parameter to unsigned long pointer in the bit
operations. Note, new compilers might warn on this line for
potential outbound access.
*) it seems a dead code, so remove it all for good
Fixes: 13d19498b0 ("GRU Driver: driver internal header files")
Acked-by: Dimitri Sivanich <sivanich@hpe.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20220214153958.9721-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Joel writes:
FSI changes for v5.18
* Improvements in SCOM and OCC drivers for error handling and retries
* Addition of tracepoints for initialisation path
* API for setting long running SBE FIFO operations
* tag 'fsi-for-v5.18' of git://git.kernel.org/pub/scm/linux/kernel/git/joel/fsi:
fsi: Add trace events in initialization path
fsi: sbefifo: Implement FSI_SBEFIFO_READ_TIMEOUT_SECONDS ioctl
fsi: sbefifo: Use specified value of start of response timeout
fsi: occ: Improve response status checking
fsi: scom: Remove retries in indirect scoms
fsi: scom: Fix error handling
FSI_SBEFIFO_READ_TIMEOUT_SECONDS ioctl sets the read timeout (in
seconds) for the response received by sbefifo device from sbe. The
timeout affects only the read operation on current sbefifo device fd.
Certain SBE operations can take long time to complete and the default
timeout of 10 seconds might not be sufficient to start receiving
response from SBE. In such cases, allow the timeout to be set to the
maximum of 120 seconds.
The kernel does not contain the definition of the various SBE
operations, so we must expose an interface to userspace to set the
timeout for the given operation.
Signed-off-by: Amitay Isaacs <amitay@ozlabs.org>
Signed-off-by: Joel Stanley <joel@jms.id.au>
Reviewed-by: Eddie James <eajames@linux.ibm.com>
Link: https://lore.kernel.org/r/20220121053816.82253-3-joel@jms.id.au
Signed-off-by: Joel Stanley <joel@jms.id.au>
For some of the chip-ops where sbe needs to collect trace information,
sbe can take a long time (>30s) to respond. Currently these chip-ops
will timeout as the start of response timeout defaults to 10s.
Instead of default value, use specified value. The require timeout
value will be set using ioctl.
Signed-off-by: Amitay Isaacs <amitay@ozlabs.org>
Signed-off-by: Joel Stanley <joel@jms.id.au>
Reviewed-by: Eddie James <eajames@linux.ibm.com>
Link: https://lore.kernel.org/r/20220121053816.82253-2-joel@jms.id.au
Signed-off-by: Joel Stanley <joel@jms.id.au>
If the driver sequence number coincidentally equals the previous
command response sequence number, the driver may proceed with
fetching the entire buffer before the OCC has processed the current
command. To be sure the correct response is obtained, check the
command type and also retry if any of the response parameters have
changed when the rest of the buffer is fetched. Also initialize the
driver with a random sequence number in order to reduce the chances
of this happening.
Signed-off-by: Eddie James <eajames@linux.ibm.com>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Link: https://lore.kernel.org/r/20220208152235.19686-1-eajames@linux.ibm.com
Signed-off-by: Joel Stanley <joel@jms.id.au>
Pull Kbuild fixes from Masahiro Yamada:
- Fix the truncated path issue for HAVE_GCC_PLUGINS test in Kconfig
- Move -Wunsligned-access to W=1 builds to avoid sprinkling warnings
for the latest Clang
- Fix missing fclose() in Kconfig
- Fix Kconfig to touch dep headers correctly when KCONFIG_AUTOCONFIG is
overridden.
* tag 'kbuild-fixes-v5.17-2' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild:
kconfig: fix failing to generate auto.conf
kconfig: fix missing fclose() on error paths
Makefile.extrawarn: Move -Wunaligned-access to W=1
kconfig: let 'shell' return enough output for deep path names
Pull irq fixes from Thomas Gleixner:
"Interrupt chip driver fixes:
- Don't install an hotplug notifier for GICV3-ITS on systems which do
not need it to prevent a warning in the notifier about inconsistent
state
- Add the missing device tree matching for the T-HEAD PLIC variant so
the related SoC is properly supported"
* tag 'irq-urgent-2022-02-13' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
irqchip/sifive-plic: Add missing thead,c900-plic match string
dt-bindings: update riscv plic compatible string
irqchip/gic-v3-its: Skip HP notifier when no ITS is registered
Pull objtool fix from Borislav Petkov:
"Fix a case where objtool would mistakenly warn about instructions
being unreachable"
* tag 'objtool_urgent_for_v5.17_rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/bug: Merge annotate_reachable() into _BUG_FLAGS() asm
Pull scheduler fix from Borislav Petkov:
"Fix a NULL-ptr dereference when recalculating a sched entity's weight"
* tag 'sched_urgent_for_v5.17_rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
sched/fair: Fix fault in reweight_entity
Pull perf fix from Borislav Petkov:
"Prevent cgroup event list corruption when switching events"
* tag 'perf_urgent_for_v5.17_rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
perf: Fix list corruption in perf_cgroup_switch()
