Fix can_boost() to identify indirect jmp and others using range case
correctly.
Since the condition in switch statement is opcode & 0xf0, it can not
evaluate to 0xff case. This should be under the 0xf0 case. However,
there is no reason to use the conbinations of the bit-masked condition
and lower bit checking.
Use range case to clean up the switch statement too.
Fixes: 6256e668b7 ("x86/kprobes: Use int3 instead of debug trap for single-step")
Reported-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Masami Hiramatsu <mhiramat@kernel.org>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Link: https://lore.kernel.org/r/161666692308.1120877.4675552834049546493.stgit@devnote2
There are 2 bugs in the can_boost() function because of using
x86 insn decoder. Since the insn->opcode never has a prefix byte,
it can not find CS override prefix in it. And the insn->attr is
the attribute of the opcode, thus inat_is_address_size_prefix(
insn->attr) always returns false.
Fix those by checking each prefix bytes with for_each_insn_prefix
loop and getting the correct attribute for each prefix byte.
Also, this removes unlikely, because this is a slow path.
Fixes: a8d11cd071 ("kprobes/x86: Consolidate insn decoder users for copying code")
Signed-off-by: Masami Hiramatsu <mhiramat@kernel.org>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Link: https://lore.kernel.org/r/161666691162.1120877.2808435205294352583.stgit@devnote2
Use int3 instead of debug trap exception for single-stepping the
probed instructions. Some instructions which change the ip
registers or modify IF flags are emulated because those are not
able to be single-stepped by int3 or may allow the interrupt
while single-stepping.
This actually changes the kprobes behavior.
- kprobes can not probe following instructions; int3, iret,
far jmp/call which get absolute address as immediate,
indirect far jmp/call, indirect near jmp/call with addressing
by memory (register-based indirect jmp/call are OK), and
vmcall/vmlaunch/vmresume/vmxoff.
- If the kprobe post_handler doesn't set before registering,
it may not be called in some case even if you set it afterwards.
(IOW, kprobe booster is enabled at registration, user can not
change it)
But both are rare issue, unsupported instructions will not be
used in the kernel (or rarely used), and post_handlers are
rarely used (I don't see it except for the test code).
Suggested-by: Andy Lutomirski <luto@kernel.org>
Signed-off-by: Masami Hiramatsu <mhiramat@kernel.org>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Link: https://lkml.kernel.org/r/161469874601.49483.11985325887166921076.stgit@devnote2
Since Grp5 far indirect JMP is FF "mod 101 r/m", it should be
(modrm & 0x38) == 0x28, and near indirect JMP is also 0x38 == 0x20.
So we can mask modrm with 0x30 and check 0x20.
This is actually what the original code does, it also doesn't care
the last bit. So the result code is same.
Thus, I think this is just a cosmetic cleanup.
Signed-off-by: Masami Hiramatsu <mhiramat@kernel.org>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Link: https://lkml.kernel.org/r/161469873475.49483.13257083019966335137.stgit@devnote2
Since the opcodes start from 0xff are group5 instruction group which is
not 2 bytes opcode but the extended opcode determined by the MOD/RM byte.
The commit abd82e533d ("x86/kprobes: Do not decode opcode in resume_execution()")
used insn->opcode.bytes[1], but that is not correct. We have to refer
the insn->modrm.bytes[1] instead.
Fixes: abd82e533d ("x86/kprobes: Do not decode opcode in resume_execution()")
Signed-off-by: Masami Hiramatsu <mhiramat@kernel.org>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Link: https://lkml.kernel.org/r/161469872400.49483.18214724458034233166.stgit@devnote2
Building perf on ppc causes:
In file included from util/intel-pt-decoder/intel-pt-insn-decoder.c:15:
util/intel-pt-decoder/../../../arch/x86/lib/insn.c:14:10: fatal error: asm/inat.h: No such file or directory
14 | #include <asm/inat.h> /*__ignore_sync_check__ */
| ^~~~~~~~~~~~
Restore the relative include paths so that the compiler can find the
headers.
Fixes: 93281c4a96 ("x86/insn: Add an insn_decode() API")
Reported-by: Ian Rogers <irogers@google.com>
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Borislav Petkov <bp@suse.de>
Tested-by: Ian Rogers <irogers@google.com>
Tested-by: Stephen Rothwell <sfr@canb.auug.org.au>
Link: https://lkml.kernel.org/r/20210317150858.02b1bbc8@canb.auug.org.au
Split it into two helpers - a user- and a kernel-mode one for
readability. Yes, the original function body is not that convoluted but
splitting it makes following through that code trivial than having to
pay attention to each little difference when in user or in kernel mode.
No functional changes.
Signed-off-by: Borislav Petkov <bp@suse.de>
Link: https://lkml.kernel.org/r/20210304174237.31945-13-bp@alien8.de
intel_pmu_pebs_fixup_ip() needs only the insn length so use the
appropriate helper instead of a full decode. A full decode differs only
in running insn_complete() on the decoded insn but that is not needed
here.
Signed-off-by: Borislav Petkov <bp@suse.de>
Link: https://lkml.kernel.org/r/20210304174237.31945-8-bp@alien8.de
Now that the different instruction-inspecting functions return a value,
test that and return early from callers if error has been encountered.
While at it, do not call insn_get_modrm() when calling
insn_get_displacement() because latter will make sure to call
insn_get_modrm() if ModRM hasn't been parsed yet.
Signed-off-by: Borislav Petkov <bp@suse.de>
Link: https://lkml.kernel.org/r/20210304174237.31945-6-bp@alien8.de
Users of the instruction decoder should use this to decode instruction
bytes. For that, have insn*() helpers return an int value to denote
success/failure. When there's an error fetching the next insn byte and
the insn falls short, return -ENODATA to denote that.
While at it, make insn_get_opcode() more stricter as to whether what has
seen so far is a valid insn and if not.
Copy linux/kconfig.h for the tools-version of the decoder so that it can
use IS_ENABLED().
Also, cast the INSN_MODE_KERN dummy define value to (enum insn_mode)
for tools use of the decoder because perf tool builds with -Werror and
errors out with -Werror=sign-compare otherwise.
Signed-off-by: Borislav Petkov <bp@suse.de>
Acked-by: Masami Hiramatsu <mhiramat@kernel.org>
Link: https://lkml.kernel.org/r/20210304174237.31945-5-bp@alien8.de
Add an explicit __ignore_sync_check__ marker which will be used to mark
lines which are supposed to be ignored by file synchronization check
scripts, its advantage being that it explicitly denotes such lines in
the code.
Signed-off-by: Borislav Petkov <bp@suse.de>
Reviewed-by: Masami Hiramatsu <mhiramat@kernel.org>
Link: https://lkml.kernel.org/r/20210304174237.31945-4-bp@alien8.de
Rename insn_decode() to insn_decode_from_regs() to denote that it
receives regs as param and uses registers from there during decoding.
Free the former name for a more generic version of the function.
No functional changes.
Signed-off-by: Borislav Petkov <bp@suse.de>
Link: https://lkml.kernel.org/r/20210304174237.31945-2-bp@alien8.de
Doing a
prctl(PR_SET_MM, PR_SET_MM_AUXV, addr, 1);
will copy 1 byte from userspace to (quite big) on-stack array
and then stash everything to mm->saved_auxv.
AT_NULL terminator will be inserted at the very end.
/proc/*/auxv handler will find that AT_NULL terminator
and copy original stack contents to userspace.
This devious scheme requires CAP_SYS_RESOURCE.
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Pull irq fixes from Thomas Gleixner:
"A set of irqchip updates:
- Make the GENERIC_IRQ_MULTI_HANDLER configuration correct
- Add a missing DT compatible string for the Ingenic driver
- Remove the pointless debugfs_file pointer from struct irqdomain"
* tag 'irq-urgent-2021-03-14' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
irqchip/ingenic: Add support for the JZ4760
dt-bindings/irq: Add compatible string for the JZ4760B
irqchip: Do not blindly select CONFIG_GENERIC_IRQ_MULTI_HANDLER
ARM: ep93xx: Select GENERIC_IRQ_MULTI_HANDLER directly
irqdomain: Remove debugfs_file from struct irq_domain
Pull timer fix from Thomas Gleixner:
"A single fix in for hrtimers to prevent an interrupt storm caused by
the lack of reevaluation of the timers which expire in softirq context
under certain circumstances, e.g. when the clock was set"
* tag 'timers-urgent-2021-03-14' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
hrtimer: Update softirq_expires_next correctly after __hrtimer_get_next_event()
Pull scheduler fixes from Thomas Gleixner:
"A set of scheduler updates:
- Prevent a NULL pointer dereference in the migration_stop_cpu()
mechanims
- Prevent self concurrency of affine_move_task()
- Small fixes and cleanups related to task migration/affinity setting
- Ensure that sync_runqueues_membarrier_state() is invoked on the
current CPU when it is in the cpu mask"
* tag 'sched-urgent-2021-03-14' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
sched/membarrier: fix missing local execution of ipi_sync_rq_state()
sched: Simplify set_affinity_pending refcounts
sched: Fix affine_move_task() self-concurrency
sched: Optimize migration_cpu_stop()
sched: Collate affine_move_task() stoppers
sched: Simplify migration_cpu_stop()
sched: Fix migration_cpu_stop() requeueing
Pull objtool fix from Thomas Gleixner:
"A single objtool fix to handle the PUSHF/POPF validation correctly for
the paravirt changes which modified arch_local_irq_restore not to use
popf"
* tag 'objtool-urgent-2021-03-14' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
objtool,x86: Fix uaccess PUSHF/POPF validation
Pull locking fixes from Thomas Gleixner:
"A couple of locking fixes:
- A fix for the static_call mechanism so it handles unaligned
addresses correctly.
- Make u64_stats_init() a macro so every instance gets a seperate
lockdep key.
- Make seqcount_latch_init() a macro as well to preserve the static
variable which is used for the lockdep key"
* tag 'locking-urgent-2021-03-14' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
seqlock,lockdep: Fix seqcount_latch_init()
u64_stats,lockdep: Fix u64_stats_init() vs lockdep
static_call: Fix the module key fixup
Pull perf fixes from Borislav Petkov:
- Make sure PMU internal buffers are flushed for per-CPU events too and
properly handle PID/TID for large PEBS.
- Handle the case properly when there's no PMU and therefore return an
empty list of perf MSRs for VMX to switch instead of reading random
garbage from the stack.
* tag 'perf_urgent_for_v5.12-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/perf: Use RET0 as default for guest_get_msrs to handle "no PMU" case
perf/x86/intel: Set PERF_ATTACH_SCHED_CB for large PEBS and LBR
perf/core: Flush PMU internal buffers for per-CPU events
Pull EFI fix from Ard Biesheuvel via Borislav Petkov:
"Fix an oversight in the handling of EFI_RT_PROPERTIES_TABLE, which was
added v5.10, but failed to take the SetVirtualAddressMap() RT service
into account"
* tag 'efi-urgent-for-v5.12-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
efi: stub: omit SetVirtualAddressMap() if marked unsupported in RT_PROP table
Pull x86 fixes from Borislav Petkov:
- A couple of SEV-ES fixes and robustifications: verify usermode stack
pointer in NMI is not coming from the syscall gap, correctly track
IRQ states in the #VC handler and access user insn bytes atomically
in same handler as latter cannot sleep.
- Balance 32-bit fast syscall exit path to do the proper work on exit
and thus not confuse audit and ptrace frameworks.
- Two fixes for the ORC unwinder going "off the rails" into KASAN
redzones and when ORC data is missing.
* tag 'x86_urgent_for_v5.12_rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/sev-es: Use __copy_from_user_inatomic()
x86/sev-es: Correctly track IRQ states in runtime #VC handler
x86/sev-es: Check regs->sp is trusted before adjusting #VC IST stack
x86/sev-es: Introduce ip_within_syscall_gap() helper
x86/entry: Fix entry/exit mismatch on failed fast 32-bit syscalls
x86/unwind/orc: Silence warnings caused by missing ORC data
x86/unwind/orc: Disable KASAN checking in the ORC unwinder, part 2
Pull powerpc fixes from Michael Ellerman:
"Some more powerpc fixes for 5.12:
- Fix wrong instruction encoding for lis in ppc_function_entry(),
which could potentially lead to missed kprobes.
- Fix SET_FULL_REGS on 32-bit and 64e, which prevented ptrace of
non-volatile GPRs immediately after exec.
- Clean up a missed SRR specifier in the recent interrupt rework.
- Don't treat unrecoverable_exception() as an interrupt handler, it's
called from other handlers so shouldn't do the interrupt entry/exit
accounting itself.
- Fix build errors caused by missing declarations for
[en/dis]able_kernel_vsx().
Thanks to Christophe Leroy, Daniel Axtens, Geert Uytterhoeven, Jiri
Olsa, Naveen N. Rao, and Nicholas Piggin"
* tag 'powerpc-5.12-3' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux:
powerpc/traps: unrecoverable_exception() is not an interrupt handler
powerpc: Fix missing declaration of [en/dis]able_kernel_vsx()
powerpc/64s/exception: Clean up a missed SRR specifier
powerpc: Fix inverted SET_FULL_REGS bitop
powerpc/64s: Use symbolic macros for function entry encoding
powerpc/64s: Fix instruction encoding for lis in ppc_function_entry()
Pull KVM fixes from Paolo Bonzini:
"More fixes for ARM and x86"
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm:
KVM: LAPIC: Advancing the timer expiration on guest initiated write
KVM: x86/mmu: Skip !MMU-present SPTEs when removing SP in exclusive mode
KVM: kvmclock: Fix vCPUs > 64 can't be online/hotpluged
kvm: x86: annotate RCU pointers
KVM: arm64: Fix exclusive limit for IPA size
KVM: arm64: Reject VM creation when the default IPA size is unsupported
KVM: arm64: Ensure I-cache isolation between vcpus of a same VM
KVM: arm64: Don't use cbz/adr with external symbols
KVM: arm64: Fix range alignment when walking page tables
KVM: arm64: Workaround firmware wrongly advertising GICv2-on-v3 compatibility
KVM: arm64: Rename __vgic_v3_get_ich_vtr_el2() to __vgic_v3_get_gic_config()
KVM: arm64: Don't access PMSELR_EL0/PMUSERENR_EL0 when no PMU is available
KVM: arm64: Turn kvm_arm_support_pmu_v3() into a static key
KVM: arm64: Fix nVHE hyp panic host context restore
KVM: arm64: Avoid corrupting vCPU context register in guest exit
KVM: arm64: nvhe: Save the SPE context early
kvm: x86: use NULL instead of using plain integer as pointer
KVM: SVM: Connect 'npt' module param to KVM's internal 'npt_enabled'
KVM: x86: Ensure deadline timer has truly expired before posting its IRQ
Merge misc fixes from Andrew Morton:
"28 patches.
Subsystems affected by this series: mm (memblock, pagealloc, hugetlb,
highmem, kfence, oom-kill, madvise, kasan, userfaultfd, memcg, and
zram), core-kernel, kconfig, fork, binfmt, MAINTAINERS, kbuild, and
ia64"
* emailed patches from Andrew Morton <akpm@linux-foundation.org>: (28 commits)
zram: fix broken page writeback
zram: fix return value on writeback_store
mm/memcg: set memcg when splitting page
mm/memcg: rename mem_cgroup_split_huge_fixup to split_page_memcg and add nr_pages argument
ia64: fix ptrace(PTRACE_SYSCALL_INFO_EXIT) sign
ia64: fix ia64_syscall_get_set_arguments() for break-based syscalls
mm/userfaultfd: fix memory corruption due to writeprotect
kasan: fix KASAN_STACK dependency for HW_TAGS
kasan, mm: fix crash with HW_TAGS and DEBUG_PAGEALLOC
mm/madvise: replace ptrace attach requirement for process_madvise
include/linux/sched/mm.h: use rcu_dereference in in_vfork()
kfence: fix reports if constant function prefixes exist
kfence, slab: fix cache_alloc_debugcheck_after() for bulk allocations
kfence: fix printk format for ptrdiff_t
linux/compiler-clang.h: define HAVE_BUILTIN_BSWAP*
MAINTAINERS: exclude uapi directories in API/ABI section
binfmt_misc: fix possible deadlock in bm_register_write
mm/highmem.c: fix zero_user_segments() with start > end
hugetlb: do early cow when page pinned on src mm
mm: use is_cow_mapping() across tree where proper
...
Pull irqchip fixes from Marc Zyngier:
- More compatible strings for the Ingenic irqchip (introducing the
JZ4760B SoC)
- Select GENERIC_IRQ_MULTI_HANDLER on the ARM ep93xx platform
- Drop all GENERIC_IRQ_MULTI_HANDLER selections from the irqchip
Kconfig, now relying on the architecture to get it right
- Drop the debugfs_file field from struct irq_domain, now that
debugfs can track things on its own
Pull char/misc driver fixes from Greg KH:
"Here are some small misc/char driver fixes to resolve some reported
problems:
- habanalabs driver fixes
- Acrn build fixes (reported many times)
- pvpanic module table export fix
All of these have been in linux-next for a while with no reported
issues"
* tag 'char-misc-5.12-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc:
misc/pvpanic: Export module FDT device table
misc: fastrpc: restrict user apps from sending kernel RPC messages
virt: acrn: Correct type casting of argument of copy_from_user()
virt: acrn: Use EPOLLIN instead of POLLIN
virt: acrn: Use vfs_poll() instead of f_op->poll()
virt: acrn: Make remove_cpu sysfs invisible with !CONFIG_HOTPLUG_CPU
cpu/hotplug: Fix build error of using {add,remove}_cpu() with !CONFIG_SMP
habanalabs: fix debugfs address translation
habanalabs: Disable file operations after device is removed
habanalabs: Call put_pid() when releasing control device
drivers: habanalabs: remove unused dentry pointer for debugfs files
habanalabs: mark hl_eq_inc_ptr() as static
Pull staging driver fixes from Greg KH:
"Here are some small staging driver fixes for reported problems. They
include:
- wfx header file cleanup patch reverted as it could cause problems
- comedi driver endian fixes
- buffer overflow problems for staging wifi drivers
- build dependency issue for rtl8192e driver
All have been in linux-next for a while with no reported problems"
* tag 'staging-5.12-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging: (23 commits)
Revert "staging: wfx: remove unused included header files"
staging: rtl8188eu: prevent ->ssid overflow in rtw_wx_set_scan()
staging: rtl8188eu: fix potential memory corruption in rtw_check_beacon_data()
staging: rtl8192u: fix ->ssid overflow in r8192_wx_set_scan()
staging: comedi: pcl726: Use 16-bit 0 for interrupt data
staging: comedi: ni_65xx: Use 16-bit 0 for interrupt data
staging: comedi: ni_6527: Use 16-bit 0 for interrupt data
staging: comedi: comedi_parport: Use 16-bit 0 for interrupt data
staging: comedi: amplc_pc236_common: Use 16-bit 0 for interrupt data
staging: comedi: pcl818: Fix endian problem for AI command data
staging: comedi: pcl711: Fix endian problem for AI command data
staging: comedi: me4000: Fix endian problem for AI command data
staging: comedi: dmm32at: Fix endian problem for AI command data
staging: comedi: das800: Fix endian problem for AI command data
staging: comedi: das6402: Fix endian problem for AI command data
staging: comedi: adv_pci1710: Fix endian problem for AI command data
staging: comedi: addi_apci_1500: Fix endian problem for command sample
staging: comedi: addi_apci_1032: Fix endian problem for COS sample
staging: ks7010: prevent buffer overflow in ks_wlan_set_scan()
staging: rtl8712: Fix possible buffer overflow in r8712_sitesurvey_cmd
...
Pull tty/serial fixes from Greg KH:
"Here are some small tty and serial driver fixes to resolve some
reported problems:
- led tty trigger fixes based on review and were acked by the led
maintainer
- revert a max310x serial driver patch as it was causing problems
- revert a pty change as it was also causing problems
All of these have been in linux-next for a while with no reported
problems"
* tag 'tty-5.12-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty:
Revert "drivers:tty:pty: Fix a race causing data loss on close"
Revert "serial: max310x: rework RX interrupt handling"
leds: trigger/tty: Use led_set_brightness_sync() from workqueue
leds: trigger: Fix error path to not unlock the unlocked mutex
Pull USB fixes from Greg KH:
"Here are a small number of USB fixes for 5.12-rc3 to resolve a bunch
of reported issues:
- usbip fixups for issues found by syzbot
- xhci driver fixes and quirk additions
- gadget driver fixes
- dwc3 QCOM driver fix
- usb-serial new ids and fixes
- usblp fix for a long-time issue
- cdc-acm quirk addition
- other tiny fixes for reported problems
All of these have been in linux-next for a while with no reported
issues"
* tag 'usb-5.12-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (25 commits)
xhci: Fix repeated xhci wake after suspend due to uncleared internal wake state
usb: xhci: Fix ASMedia ASM1042A and ASM3242 DMA addressing
xhci: Improve detection of device initiated wake signal.
usb: xhci: do not perform Soft Retry for some xHCI hosts
usbip: fix vudc usbip_sockfd_store races leading to gpf
usbip: fix vhci_hcd attach_store() races leading to gpf
usbip: fix stub_dev usbip_sockfd_store() races leading to gpf
usbip: fix vudc to check for stream socket
usbip: fix vhci_hcd to check for stream socket
usbip: fix stub_dev to check for stream socket
usb: dwc3: qcom: Add missing DWC3 OF node refcount decrement
USB: usblp: fix a hang in poll() if disconnected
USB: gadget: udc: s3c2410_udc: fix return value check in s3c2410_udc_probe()
usb: renesas_usbhs: Clear PIPECFG for re-enabling pipe with other EPNUM
usb: dwc3: qcom: Honor wakeup enabled/disabled state
usb: gadget: f_uac1: stop playback on function disable
usb: gadget: f_uac2: always increase endpoint max_packet_size by one audio slot
USB: gadget: u_ether: Fix a configfs return code
usb: dwc3: qcom: add ACPI device id for sc8180x
Goodix Fingerprint device is not a modem
...
