Add irq fixup infrastructure to handle IP blocks connected to shared irqs
that are left in an unknown state when booting the kernel.
In this case the IP block which has not masked its interrupt and has no
driver loaded (either because it is not compiled or because it is not
loaded yet) might generate spurious interrupts when another IP block
request the shared irq.
A good example of this case is the RTC block on which register configs are
kept even after a shutdown (if a proper VDDcore is supplied), and thus
might generate spurious interrupts when the platform is switched on.
Signed-off-by: Boris BREZILLON <boris.brezillon@free-electrons.com>
Link: https://lkml.kernel.org/r/1405016741-2407-2-git-send-email-boris.brezillon@free-electrons.com
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
In addition to consolidating the or1k-pic with other interrupt
controllers, this makes OpenRISC less tied to its on-cpu
interrupt controller.
All or1k-pic specific parts are moved out of irq.c and into
drivers/irqchip/irq-or1k-pic.c
In that transition, the functionality have been divided into
three chip variants.
One that handles level triggered interrupts, one that handles edge
triggered interrupts and one that handles the interrupt
controller that is present in the or1200 OpenRISC cpu
implementation.
Signed-off-by: Stefan Kristiansson <stefan.kristiansson@saunalahti.fi>
Link: https://lkml.kernel.org/r/1401136302-27654-1-git-send-email-stefan.kristiansson@saunalahti.fi
Acked-by: Jonas Bonn <jonas@southpole.se>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
On certain platforms such as DRA7, SPIs 0, 1, 2, 3, 5, 6, 10, 131,
132, 133 are direct wired to hardware blocks bypassing crossbar.
This quirky implementation is *NOT* supposed to be the expectation
of crossbar hardware usage. However, these are already marked in our
description of the hardware with SKIP and RESERVED where appropriate.
Unfortunately, we need to be able to refer to these hardwired IRQs.
So, to request these, crossbar driver can use the existing information
from it's table that these SKIP/RESERVED maps are direct wired sources
and generic allocation/programming of crossbar should be avoided.
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Sricharan R <r.sricharan@ti.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Link: https://lkml.kernel.org/r/1403766634-18543-17-git-send-email-r.sricharan@ti.com
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Currently we attempt to map any crossbar value to an IRQ, however,
this is not correct from hardware perspective. There is a max crossbar
event number upto which hardware supports. So describe the same in
device tree using 'ti,max-crossbar-sources' property and use it to
validate requests.
[ jac - remove MAX_SOURCES from binding doc, use integer because we
shouldn't put implementation details in the binding docs ]
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Sricharan R <r.sricharan@ti.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Link: https://lkml.kernel.org/r/1403766634-18543-14-git-send-email-r.sricharan@ti.com
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Adding missing properties for kerneldoc (@write) and cleanup
of harmless warnings while we are here.
kerneldoc warnings:
Warning(drivers/irqchip/irq-crossbar.c:27): missing initial short description on line:
* struct crossbar_device: crossbar device description
Info(drivers/irqchip/irq-crossbar.c:27): Scanning doc for struct
Warning(drivers/irqchip/irq-crossbar.c:39): No description found for parameter 'write'
2 warnings
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Sricharan R <r.sricharan@ti.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Link: https://lkml.kernel.org/r/1403766634-18543-9-git-send-email-r.sricharan@ti.com
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
There is absolutely no need for crossbar driver to expose functions and
variables into global namespace. So make them all static
Also fix a couple of checkpatch warnings.
Fixes sparse warnings:
drivers/irqchip/irq-crossbar.c:129:29: warning: symbol 'routable_irq_domain_ops' was not declared. Should it be static?
drivers/irqchip/irq-crossbar.c:261:12: warning: symbol 'irqcrossbar_init' was not declared. Should it be static?
Checkpatch warnings:
WARNING: Prefer kcalloc over kzalloc with multiply
+ cb->irq_map = kzalloc(max * sizeof(int), GFP_KERNEL);
WARNING: Prefer kcalloc over kzalloc with multiply
+ cb->register_offsets = kzalloc(max * sizeof(int), GFP_KERNEL);
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Sricharan R <r.sricharan@ti.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Link: https://lkml.kernel.org/r/1403766634-18543-8-git-send-email-r.sricharan@ti.com
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Reverse the search algorithm to ensure that address mapping and IRQ
allocation logics are proper. This makes the below bugs visible sooner.
class 1. address space errors -> example:
reg = <a size_b>
ti,max-irqs = is a wrong parameter
class 2: irq-reserved list - which decides which entries in the
address space is not actually wired in
class 3: wrong list of routable-irqs.
In general allocating from max to min tends to have benefits in
ensuring the different issues that may be present in dts is easily
caught at definition time, rather than at a later point in time.
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Sricharan R <r.sricharan@ti.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Link: https://lkml.kernel.org/r/1403766634-18543-6-git-send-email-r.sricharan@ti.com
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Since crossbar is s/w configurable, the initial settings of the
crossbar cannot be assumed to be sane. This implies that:
a) On initialization all un-reserved crossbars must be initialized to
a known 'safe' value.
b) When unmapping the interrupt, the safe value must be written to
ensure that the crossbar mapping matches with interrupt controller
usage.
So provide a safe value in the dt data to map if
'0' is not safe for the platform and use it during init and unmap
While at this, fix the below checkpatch warning.
Fixes checkpatch warning:
WARNING: Unnecessary space before function pointer arguments
#37: FILE: drivers/irqchip/irq-crossbar.c:37:
+ void (*write) (int, int);
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Sricharan R <r.sricharan@ti.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Link: https://lkml.kernel.org/r/1403766634-18543-5-git-send-email-r.sricharan@ti.com
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Only spear300 has an actual mask register for the RAS interrupts. Add
an irq chip pointer to the shirq struct and initialize spear300 with
the actual implementation and the others with dummy_irq_chip. The
disabled RAS3 block has no irq chip assigned, so we can check for this
and remove the disabled member.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://lkml.kernel.org/r/20140619212713.831341023@linutronix.de
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
The ras3 block on spear320 claims to have 3 interrupts. In fact it has
one and 6 reserved interrupts. Account the 6 reserved to this block so
it has 7 interrupts total. That matches the datasheet and the device
tree entries.
Broken since commit 80515a5a(ARM: SPEAr3xx: shirq: simplify and move
the shared irq multiplexor to DT). Testing is overrated....
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://lkml.kernel.org/r/20140619212712.872379208@linutronix.de
Fixes: 80515a5a2e ('ARM: SPEAr3xx: shirq: simplify and move the shared irq multiplexor to DT')
Cc: <stable@vger.kernel.org> # v3.8+
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Until now, the irq-armada-370-xp irqchip driver was not masking all
interrupts at initialization. While in most cases this is not a
problem because the bootloader has probably masked all interrupts, it
becomes a problem when you use kexec: you're in kernel A, with many
interrupts enabled, and then kexec into kernel B, without going
through the bootloader. So during the boot process, if an interrupt
occurs while the corresponding driver has not been loaded, you would
get spurious interrupts.
This commit fixes that by ensuring all interrupts are properly masked
when the irqchip driver is initialized. Note that interrupt masking
takes place at two level: at the global level (main_int_base) and at
the per-CPU level (per_cpu_int_base).
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Link: https://lkml.kernel.org/r/1401481098-23326-6-git-send-email-thomas.petazzoni@free-electrons.com
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Pull networking fixes from David Miller:
1) Fix checksumming regressions, from Tom Herbert.
2) Undo unintentional permissions changes for SCTP rto_alpha and
rto_beta sysfs knobs, from Denial Borkmann.
3) VXLAN, like other IP tunnels, should advertize it's encapsulation
size using dev->needed_headroom instead of dev->hard_header_len.
From Cong Wang.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net:
net: sctp: fix permissions for rto_alpha and rto_beta knobs
vxlan: Checksum fixes
net: add skb_pop_rcv_encapsulation
udp: call __skb_checksum_complete when doing full checksum
net: Fix save software checksum complete
net: Fix GSO constants to match NETIF flags
udp: ipv4: do not waste time in __udp4_lib_mcast_demux_lookup
vxlan: use dev->needed_headroom instead of dev->hard_header_len
MAINTAINERS: update cxgb4 maintainer
Pull more clock framework updates from Mike Turquette:
"This contains the second half the of the clk changes for 3.16.
They are simply fixes and code refactoring for the OMAP clock drivers.
The sunxi clock driver changes include splitting out the one
mega-driver into several smaller pieces and adding support for the A31
SoC clocks"
* tag 'clk-for-linus-3.16-part2' of git://git.linaro.org/people/mike.turquette/linux: (25 commits)
clk: sunxi: document PRCM clock compatible strings
clk: sunxi: add PRCM (Power/Reset/Clock Management) clks support
clk: sun6i: Protect SDRAM gating bit
clk: sun6i: Protect CPU clock
clk: sunxi: Rework clock protection code
clk: sunxi: Move the GMAC clock to a file of its own
clk: sunxi: Move the 24M oscillator to a file of its own
clk: sunxi: Remove calls to clk_put
clk: sunxi: document new A31 USB clock compatible
clk: sunxi: Implement A31 USB clock
ARM: dts: OMAP5/DRA7: use omap5-mpu-dpll-clock capable of dealing with higher frequencies
CLK: TI: dpll: support OMAP5 MPU DPLL that need special handling for higher frequencies
ARM: OMAP5+: dpll: support Duty Cycle Correction(DCC)
CLK: TI: clk-54xx: Set the rate for dpll_abe_m2x2_ck
CLK: TI: Driver for DRA7 ATL (Audio Tracking Logic)
dt:/bindings: DRA7 ATL (Audio Tracking Logic) clock bindings
ARM: dts: dra7xx-clocks: Correct name for atl clkin3 clock
CLK: TI: gate: add composite interface clock to OMAP2 only build
ARM: OMAP2: clock: add DT boot support for cpufreq_ck
CLK: TI: OMAP2: add clock init support
...
Pull NVMe update from Matthew Wilcox:
"Mostly bugfixes again for the NVMe driver. I'd like to call out the
exported tracepoint in the block layer; I believe Keith has cleared
this with Jens.
We've had a few reports from people who're really pounding on NVMe
devices at scale, hence the timeout changes (and new module
parameters), hotplug cpu deadlock, tracepoints, and minor performance
tweaks"
[ Jens hadn't seen that tracepoint thing, but is ok with it - it will
end up going away when mq conversion happens ]
* git://git.infradead.org/users/willy/linux-nvme: (22 commits)
NVMe: Fix START_STOP_UNIT Scsi->NVMe translation.
NVMe: Use Log Page constants in SCSI emulation
NVMe: Define Log Page constants
NVMe: Fix hot cpu notification dead lock
NVMe: Rename io_timeout to nvme_io_timeout
NVMe: Use last bytes of f/w rev SCSI Inquiry
NVMe: Adhere to request queue block accounting enable/disable
NVMe: Fix nvme get/put queue semantics
NVMe: Delete NVME_GET_FEAT_TEMP_THRESH
NVMe: Make admin timeout a module parameter
NVMe: Make iod bio timeout a parameter
NVMe: Prevent possible NULL pointer dereference
NVMe: Fix the buffer size passed in GetLogPage(CDW10.NUMD)
NVMe: Update data structures for NVMe 1.2
NVMe: Enable BUILD_BUG_ON checks
NVMe: Update namespace and controller identify structures to the 1.1a spec
NVMe: Flush with data support
NVMe: Configure support for block flush
NVMe: Add tracepoints
NVMe: Protect against badly formatted CQEs
...
Commit 3fd091e73b ("[SCTP]: Remove multiple levels of msecs
to jiffies conversions.") has silently changed permissions for
rto_alpha and rto_beta knobs from 0644 to 0444. The purpose of
this was to discourage users from tweaking rto_alpha and
rto_beta knobs in production environments since they are key
to correctly compute rtt/srtt.
RFC4960 under section 6.3.1. RTO Calculation says regarding
rto_alpha and rto_beta under rule C3 and C4:
[...]
C3) When a new RTT measurement R' is made, set
RTTVAR <- (1 - RTO.Beta) * RTTVAR + RTO.Beta * |SRTT - R'|
and
SRTT <- (1 - RTO.Alpha) * SRTT + RTO.Alpha * R'
Note: The value of SRTT used in the update to RTTVAR
is its value before updating SRTT itself using the
second assignment. After the computation, update
RTO <- SRTT + 4 * RTTVAR.
C4) When data is in flight and when allowed by rule C5
below, a new RTT measurement MUST be made each round
trip. Furthermore, new RTT measurements SHOULD be
made no more than once per round trip for a given
destination transport address. There are two reasons
for this recommendation: First, it appears that
measuring more frequently often does not in practice
yield any significant benefit [ALLMAN99]; second,
if measurements are made more often, then the values
of RTO.Alpha and RTO.Beta in rule C3 above should be
adjusted so that SRTT and RTTVAR still adjust to
changes at roughly the same rate (in terms of how many
round trips it takes them to reflect new values) as
they would if making only one measurement per
round-trip and using RTO.Alpha and RTO.Beta as given
in rule C3. However, the exact nature of these
adjustments remains a research issue.
[...]
While it is discouraged to adjust rto_alpha and rto_beta
and not further specified how to adjust them, the RFC also
doesn't explicitly forbid it, but rather gives a RECOMMENDED
default value (rto_alpha=3, rto_beta=2). We have a couple
of users relying on the old permissions before they got
changed. That said, if someone really has the urge to adjust
them, we could allow it with a warning in the log.
Fixes: 3fd091e73b ("[SCTP]: Remove multiple levels of msecs to jiffies conversions.")
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Cc: Vlad Yasevich <vyasevich@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
