kernel test robot reported the splat below. [0]
Before commit fed176bf31 ("net: Add ops_undo_single for module
load/unload."), if CONFIG_NET_NS=n, ops was linked to pernet_list
only when init_net had not been initialised, and ops was unlinked
from pernet_list only under the same condition.
Let's say an ops is loaded before the init_net setup but unloaded
after that. Then, the ops remains in pernet_list, which seems odd.
The cited commit added ops_undo_single(), which calls list_add() for
ops to link it to a temporary list, so a minor change was added to
__register_pernet_operations() and __unregister_pernet_operations()
under CONFIG_NET_NS=n to avoid the pernet_list corruption.
However, the corruption must have been left as is.
When CONFIG_NET_NS=n, pernet_list was used to keep ops registered
before the init_net setup, and after that, pernet_list was not used
at all.
This was because some ops annotated with __net_initdata are cleared
out of memory at some point during boot.
Then, such ops is initialised by POISON_FREE_INITMEM (0xcc), resulting
in that ops->list.{next,prev} suddenly switches from a valid pointer
to a weird value, 0xcccccccccccccccc.
To avoid such wild memory access, let's allow the pernet_list
corruption for CONFIG_NET_NS=n.
[0]:
Oops: general protection fault, probably for non-canonical address 0xf999959999999999: 0000 [#1] SMP KASAN NOPTI
KASAN: maybe wild-memory-access in range [0xccccccccccccccc8-0xcccccccccccccccf]
CPU: 2 UID: 0 PID: 346 Comm: modprobe Not tainted 6.15.0-rc1-00294-ga4cba7e98e35 #85 PREEMPT(voluntary)
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS rel-1.16.0-0-gd239552ce722-prebuilt.qemu.org 04/01/2014
RIP: 0010:__list_add_valid_or_report (lib/list_debug.c:32)
Code: 48 c1 ea 03 80 3c 02 00 0f 85 5a 01 00 00 49 39 74 24 08 0f 85 83 00 00 00 48 b8 00 00 00 00 00 fc ff df 48 89 f2 48 c1 ea 03 <80> 3c 02 00 0f 85 1f 01 00 00 4c 39 26 0f 85 ab 00 00 00 4c 39 ee
RSP: 0018:ff11000135b87830 EFLAGS: 00010a07
RAX: dffffc0000000000 RBX: ffffffffc02223c0 RCX: ffffffff8406fcc2
RDX: 1999999999999999 RSI: cccccccccccccccc RDI: ffffffffc02223c0
RBP: ffffffff86064e40 R08: 0000000000000001 R09: fffffbfff0a9f5b5
R10: ffffffff854fadaf R11: 676552203a54454e R12: ffffffff86064e40
R13: ffffffffc02223c0 R14: ffffffff86064e48 R15: 0000000000000021
FS: 00007f6fb0d9e1c0(0000) GS:ff11000858ea0000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 00007f6fb0eda580 CR3: 0000000122fec005 CR4: 0000000000771ef0
DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
DR3: 0000000000000000 DR6: 00000000fffe07f0 DR7: 0000000000000400
PKRU: 55555554
Call Trace:
<TASK>
register_pernet_operations (./include/linux/list.h:150 (discriminator 5) ./include/linux/list.h:183 (discriminator 5) net/core/net_namespace.c:1315 (discriminator 5) net/core/net_namespace.c:1359 (discriminator 5))
register_pernet_subsys (net/core/net_namespace.c:1401)
inet6_init (net/ipv6/af_inet6.c:535) ipv6
do_one_initcall (init/main.c:1257)
do_init_module (kernel/module/main.c:2942)
load_module (kernel/module/main.c:3409)
init_module_from_file (kernel/module/main.c:3599)
idempotent_init_module (kernel/module/main.c:3611)
__x64_sys_finit_module (./include/linux/file.h:62 ./include/linux/file.h:83 kernel/module/main.c:3634 kernel/module/main.c:3621 kernel/module/main.c:3621)
do_syscall_64 (arch/x86/entry/syscall_64.c:63 arch/x86/entry/syscall_64.c:94)
entry_SYSCALL_64_after_hwframe (arch/x86/entry/entry_64.S:130)
RIP: 0033:0x7f6fb0df7e5d
Code: ff c3 66 2e 0f 1f 84 00 00 00 00 00 90 f3 0f 1e fa 48 89 f8 48 89 f7 48 89 d6 48 89 ca 4d 89 c2 4d 89 c8 4c 8b 4c 24 08 0f 05 <48> 3d 01 f0 ff ff 73 01 c3 48 8b 0d 73 9f 1b 00 f7 d8 64 89 01 48
RSP: 002b:00007fffdc6a8968 EFLAGS: 00000246 ORIG_RAX: 0000000000000139
RAX: ffffffffffffffda RBX: 000055b535721b70 RCX: 00007f6fb0df7e5d
RDX: 0000000000000000 RSI: 000055b51e44aa2a RDI: 0000000000000004
RBP: 0000000000040000 R08: 0000000000000000 R09: 000055b535721b30
R10: 0000000000000004 R11: 0000000000000246 R12: 000055b51e44aa2a
R13: 000055b535721bf0 R14: 000055b5357220b0 R15: 0000000000000000
</TASK>
Modules linked in: ipv6(+) crc_ccitt
Fixes: fed176bf31 ("net: Add ops_undo_single for module load/unload.")
Reported-by: kernel test robot <oliver.sang@intel.com>
Closes: https://lore.kernel.org/oe-lkp/202504181511.1c3f23e4-lkp@intel.com
Signed-off-by: Kuniyuki Iwashima <kuniyu@amazon.com>
Link: https://patch.msgid.link/20250418215025.87871-1-kuniyu@amazon.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Jakub Kicinski says:
====================
netlink: specs: rtnetlink: adjust specs for C codegen
The first patch brings a schema extension allowing specifying
"header" (as in .h file) properties in attribute sets.
This is used for rare cases where we carry attributes from
another family in a nest - we need to include the extra
headers. If we were to generate kernel code we'd also
need to skip it in the uAPI output.
The remaining 11 patches are pretty boring schema adjustments.
====================
Link: https://patch.msgid.link/20250418021706.1967583-1-kuba@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The notify property should point at the object the notifications
carry, usually the get object, not the cmd which triggers
the notification:
notify:
description: Name of the command sharing the reply type with
this notification.
Not treating this as a fix, I think that only C codegen cares.
Reviewed-by: Donald Hunter <donald.hunter@gmail.com>
Link: https://patch.msgid.link/20250418021706.1967583-12-kuba@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The purpose of the attribute list is to list the attributes
which will be included in a given message to shrink the objects
for families with huge attr spaces. Fixed headers are always
present in their entirety (between netlink header and the attrs)
so there's no point in listing their members. Current C codegen
doesn't expect them and tries to look them up in the attribute space.
Reviewed-by: Donald Hunter <donald.hunter@gmail.com>
Link: https://patch.msgid.link/20250418021706.1967583-3-kuba@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Thierry states that there are prerequists for Tegra's calibration
that should be met before starting calibration - both the RGMII and
MDIO interfaces should be idle.
This commit adds the necessary MII bus locking to ensure that the MDIO
interface is idle during calibration.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Acked-by: Thierry Reding <treding@nvidia.com>
Link: https://patch.msgid.link/E1u7EYR-001ZAS-Cr@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The CONFIG_DEFAULT_HUNG_TASK_TIMEOUT setting is only available when the
hung task detection is enabled, otherwise the code now produces a build
failure:
drivers/net/ethernet/broadcom/bnxt/bnxt.c:10188:21: error: use of undeclared identifier 'CONFIG_DEFAULT_HUNG_TASK_TIMEOUT'
10188 | max_tmo_secs > CONFIG_DEFAULT_HUNG_TASK_TIMEOUT) {
Enclose this warning logic in an #ifdef to ensure this builds.
Fixes: 0fcad44a86 ("bnxt_en: Change FW message timeout warning")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Michael Chan <michael.chan@broadcom.com>
Link: https://patch.msgid.link/20250423162827.2189658-1-arnd@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Yong Wang says:
====================
bridge: multicast: per vlan query improvement when port or vlan state changes
The current implementation of br_multicast_enable_port() only operates on
port's multicast context, which doesn't take into account in case of vlan
snooping, one downside is the port's igmp query timer will NOT resume when
port state gets changed from BR_STATE_BLOCKING to BR_STATE_FORWARDING etc.
Such code flow will briefly look like:
1.vlan snooping
--> br_multicast_port_query_expired with per vlan port_mcast_ctx
--> port in BR_STATE_BLOCKING state --> then one-shot timer discontinued
The port state could be changed by STP daemon or kernel STP, taking mstpd
as example:
2.mstpd --> netlink_sendmsg --> br_setlink --> br_set_port_state with non
blocking states, i.e. BR_STATE_LEARNING or BR_STATE_FORWARDING
--> br_port_state_selection --> br_multicast_enable_port
--> enable multicast with port's multicast_ctx
Here for per vlan snooping, the vlan context of the port should be used
instead of port's multicast_ctx. The first patch corrects such behavior.
Similarly, vlan state change also impacts multicast behavior, the 2nd patch
adds function to update the corresponding multicast context when vlan state
changes.
The 3rd patch adds the selftests to confirm that IGMP/MLD query does happen
when the STP state becomes forwarding.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Change ALL_TESTS definition to "test-per-line".
Add the test case of per vlan snooping with port stp state change to
forwarding and also vlan equivalent case in both bridge_igmp.sh and
bridge_mld.sh.
Signed-off-by: Yong Wang <yongwang@nvidia.com>
Reviewed-by: Andy Roulin <aroulin@nvidia.com>
Reviewed-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: Petr Machata <petrm@nvidia.com>
Acked-by: Nikolay Aleksandrov <razor@blackwall.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
When the vlan STP state is changed, which could be manipulated by
"bridge vlan" commands, similar to port STP state, this also impacts
multicast behaviors such as igmp query. In the scenario of per-VLAN
snooping, there's a need to update the corresponding multicast context
to re-arm the port query timer when vlan state becomes "forwarding" etc.
Update br_vlan_set_state() function to enable vlan multicast context
in such scenario.
Before the patch, the IGMP query does not happen in the last step of the
following test sequence, i.e. no growth for tx counter:
# ip link add name br1 up type bridge vlan_filtering 1 mcast_snooping 1 mcast_vlan_snooping 1 mcast_querier 1 mcast_stats_enabled 1
# bridge vlan global set vid 1 dev br1 mcast_snooping 1 mcast_querier 1 mcast_query_interval 100 mcast_startup_query_count 0
# ip link add name swp1 up master br1 type dummy
# sleep 1
# bridge vlan set vid 1 dev swp1 state 4
# ip -j -p stats show dev swp1 group xstats_slave subgroup bridge suite mcast | jq '.[]["multicast"]["igmp_queries"]["tx_v2"]'
1
# sleep 1
# ip -j -p stats show dev swp1 group xstats_slave subgroup bridge suite mcast | jq '.[]["multicast"]["igmp_queries"]["tx_v2"]'
1
# bridge vlan set vid 1 dev swp1 state 3
# sleep 2
# ip -j -p stats show dev swp1 group xstats_slave subgroup bridge suite mcast | jq '.[]["multicast"]["igmp_queries"]["tx_v2"]'
1
After the patch, the IGMP query happens in the last step of the test:
# ip link add name br1 up type bridge vlan_filtering 1 mcast_snooping 1 mcast_vlan_snooping 1 mcast_querier 1 mcast_stats_enabled 1
# bridge vlan global set vid 1 dev br1 mcast_snooping 1 mcast_querier 1 mcast_query_interval 100 mcast_startup_query_count 0
# ip link add name swp1 up master br1 type dummy
# sleep 1
# bridge vlan set vid 1 dev swp1 state 4
# ip -j -p stats show dev swp1 group xstats_slave subgroup bridge suite mcast | jq '.[]["multicast"]["igmp_queries"]["tx_v2"]'
1
# sleep 1
# ip -j -p stats show dev swp1 group xstats_slave subgroup bridge suite mcast | jq '.[]["multicast"]["igmp_queries"]["tx_v2"]'
1
# bridge vlan set vid 1 dev swp1 state 3
# sleep 2
# ip -j -p stats show dev swp1 group xstats_slave subgroup bridge suite mcast | jq '.[]["multicast"]["igmp_queries"]["tx_v2"]'
3
Signed-off-by: Yong Wang <yongwang@nvidia.com>
Reviewed-by: Andy Roulin <aroulin@nvidia.com>
Reviewed-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: Petr Machata <petrm@nvidia.com>
Acked-by: Nikolay Aleksandrov <razor@blackwall.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
When a bridge port STP state is changed from BLOCKING/DISABLED to
FORWARDING, the port's igmp query timer will NOT re-arm itself if the
bridge has been configured as per-VLAN multicast snooping.
Solve this by choosing the correct multicast context(s) to enable/disable
port multicast based on whether per-VLAN multicast snooping is enabled or
not, i.e. using per-{port, VLAN} context in case of per-VLAN multicast
snooping by re-implementing br_multicast_enable_port() and
br_multicast_disable_port() functions.
Before the patch, the IGMP query does not happen in the last step of the
following test sequence, i.e. no growth for tx counter:
# ip link add name br1 up type bridge vlan_filtering 1 mcast_snooping 1 mcast_vlan_snooping 1 mcast_querier 1 mcast_stats_enabled 1
# bridge vlan global set vid 1 dev br1 mcast_snooping 1 mcast_querier 1 mcast_query_interval 100 mcast_startup_query_count 0
# ip link add name swp1 up master br1 type dummy
# bridge link set dev swp1 state 0
# ip -j -p stats show dev swp1 group xstats_slave subgroup bridge suite mcast | jq '.[]["multicast"]["igmp_queries"]["tx_v2"]'
1
# sleep 1
# ip -j -p stats show dev swp1 group xstats_slave subgroup bridge suite mcast | jq '.[]["multicast"]["igmp_queries"]["tx_v2"]'
1
# bridge link set dev swp1 state 3
# sleep 2
# ip -j -p stats show dev swp1 group xstats_slave subgroup bridge suite mcast | jq '.[]["multicast"]["igmp_queries"]["tx_v2"]'
1
After the patch, the IGMP query happens in the last step of the test:
# ip link add name br1 up type bridge vlan_filtering 1 mcast_snooping 1 mcast_vlan_snooping 1 mcast_querier 1 mcast_stats_enabled 1
# bridge vlan global set vid 1 dev br1 mcast_snooping 1 mcast_querier 1 mcast_query_interval 100 mcast_startup_query_count 0
# ip link add name swp1 up master br1 type dummy
# bridge link set dev swp1 state 0
# ip -j -p stats show dev swp1 group xstats_slave subgroup bridge suite mcast | jq '.[]["multicast"]["igmp_queries"]["tx_v2"]'
1
# sleep 1
# ip -j -p stats show dev swp1 group xstats_slave subgroup bridge suite mcast | jq '.[]["multicast"]["igmp_queries"]["tx_v2"]'
1
# bridge link set dev swp1 state 3
# sleep 2
# ip -j -p stats show dev swp1 group xstats_slave subgroup bridge suite mcast | jq '.[]["multicast"]["igmp_queries"]["tx_v2"]'
3
Signed-off-by: Yong Wang <yongwang@nvidia.com>
Reviewed-by: Andy Roulin <aroulin@nvidia.com>
Reviewed-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: Petr Machata <petrm@nvidia.com>
Acked-by: Nikolay Aleksandrov <razor@blackwall.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 03df156dd3 ("xdp: double protect netdev->xdp_flags with
netdev->lock") introduces the netdev lock to xdp_set_features_flag().
The change includes a _locked version of the method, as it is possible
for a driver to have already acquired the netdev lock before calling
this helper. However, the same applies to
xdp_features_(set|clear)_redirect_flags(), which ends up calling the
unlocked version of xdp_set_features_flags() leading to deadlocks in
GVE, which grabs the netdev lock as part of its suspend, reset, and
shutdown processes:
[ 833.265543] WARNING: possible recursive locking detected
[ 833.270949] 6.15.0-rc1 #6 Tainted: G E
[ 833.276271] --------------------------------------------
[ 833.281681] systemd-shutdow/1 is trying to acquire lock:
[ 833.287090] ffff949d2b148c68 (&dev->lock){+.+.}-{4:4}, at: xdp_set_features_flag+0x29/0x90
[ 833.295470]
[ 833.295470] but task is already holding lock:
[ 833.301400] ffff949d2b148c68 (&dev->lock){+.+.}-{4:4}, at: gve_shutdown+0x44/0x90 [gve]
[ 833.309508]
[ 833.309508] other info that might help us debug this:
[ 833.316130] Possible unsafe locking scenario:
[ 833.316130]
[ 833.322142] CPU0
[ 833.324681] ----
[ 833.327220] lock(&dev->lock);
[ 833.330455] lock(&dev->lock);
[ 833.333689]
[ 833.333689] *** DEADLOCK ***
[ 833.333689]
[ 833.339701] May be due to missing lock nesting notation
[ 833.339701]
[ 833.346582] 5 locks held by systemd-shutdow/1:
[ 833.351205] #0: ffffffffa9c89130 (system_transition_mutex){+.+.}-{4:4}, at: __se_sys_reboot+0xe6/0x210
[ 833.360695] #1: ffff93b399e5c1b8 (&dev->mutex){....}-{4:4}, at: device_shutdown+0xb4/0x1f0
[ 833.369144] #2: ffff949d19a471b8 (&dev->mutex){....}-{4:4}, at: device_shutdown+0xc2/0x1f0
[ 833.377603] #3: ffffffffa9eca050 (rtnl_mutex){+.+.}-{4:4}, at: gve_shutdown+0x33/0x90 [gve]
[ 833.386138] #4: ffff949d2b148c68 (&dev->lock){+.+.}-{4:4}, at: gve_shutdown+0x44/0x90 [gve]
Introduce xdp_features_(set|clear)_redirect_target_locked() versions
which assume that the netdev lock has already been acquired before
setting the XDP feature flag and update GVE to use the locked version.
Fixes: 03df156dd3 ("xdp: double protect netdev->xdp_flags with netdev->lock")
Tested-by: Mina Almasry <almasrymina@google.com>
Reviewed-by: Willem de Bruijn <willemb@google.com>
Reviewed-by: Harshitha Ramamurthy <hramamurthy@google.com>
Signed-off-by: Joshua Washington <joshwash@google.com>
Acked-by: Stanislav Fomichev <sdf@fomichev.me>
Acked-by: Martin KaFai Lau <martin.lau@kernel.org>
Link: https://patch.msgid.link/20250422011643.3509287-1-joshwash@google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
ppp_exit_net() unregisters devices related to the netns under
RTNL and destroys lists and IDR.
Let's use ->exit_rtnl() for the device unregistration part to
save RTNL dances for each netns.
Note that we delegate the for_each_netdev_safe() part to
default_device_exit_batch() and replace unregister_netdevice_queue()
with ppp_nl_dellink() to align with bond, geneve, gtp, and pfcp.
Signed-off-by: Kuniyuki Iwashima <kuniyu@amazon.com>
Link: https://patch.msgid.link/20250418003259.48017-4-kuniyu@amazon.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
pfcp_net_exit() holds RTNL and cleans up all devices in the netns
and other devices tied to sockets in the netns.
We can use ->exit_rtnl() to save RTNL dance for all dying netns.
Note that we delegate the for_each_netdev() part to
default_device_exit_batch() to avoid a list corruption splat
like the one reported in commit 4ccacf8649 ("gtp: Suppress
list corruption splat in gtp_net_exit_batch_rtnl().")
Signed-off-by: Kuniyuki Iwashima <kuniyu@amazon.com>
Link: https://patch.msgid.link/20250418003259.48017-3-kuniyu@amazon.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Convert visconti to use the set_clk_tx_rate() method. By doing so,
the GMAC control register will already have been updated (unlike with
the fix_mac_speed() method) so this code can be removed while porting
to the set_clk_tx_rate() method.
There is also no need for the spinlock, and has never been - neither
fix_mac_speed() nor set_clk_tx_rate() can be called by more than one
thread at a time, so the lock does nothing useful.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Acked-by: Nobuhiro Iwamatsu <nobuhiro1.iwamatsu@toshiba.co.jp>
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Link: https://patch.msgid.link/E1u5SiQ-001I0B-OQ@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
GBETH IP on the Renesas RZ/V2H(P) SoC is integrated with Synopsys
DesignWare MAC (version 5.20). Document the device tree bindings for
the GBETH glue layer.
Generic compatible string 'renesas,rzv2h-gbeth' is added since this
module is identical on both the RZ/V2H(P) and RZ/G3E SoCs.
The Rx/Tx clocks supplied for GBETH on the RZ/V2H(P) SoC is depicted
below:
Rx / Tx
-------+------------- on / off -------
|
| Rx-180 / Tx-180
+---- not ---- on / off -------
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Rob Herring (Arm) <robh@kernel.org>
Link: https://patch.msgid.link/20250417084015.74154-3-prabhakar.mahadev-lad.rj@bp.renesas.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Increase the `maxItems` value for the `interrupts` and `interrupt-names`
properties to 11 to support additional per-channel Tx/Rx completion
interrupts on the Renesas RZ/V2H(P) SoC, which features the
`snps,dwmac-5.20` IP.
Refactor the `interrupt-names` property by replacing repeated `enum`
entries with a `oneOf` list. Add support for per-channel receive and
transmit completion interrupts using regex patterns.
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Rob Herring (Arm) <robh@kernel.org>
Link: https://patch.msgid.link/20250417084015.74154-2-prabhakar.mahadev-lad.rj@bp.renesas.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
GCC 15's new -Wunterminated-string-initialization notices that the 32
character "flash_cookie" (which is not used as a C-String)
needs to be marked as "nonstring":
drivers/net/ethernet/emulex/benet/be_cmds.c:2618:51: warning: initializer-string for array of 'char' truncates NUL terminator but destination lacks 'nonstring' attribute (17 chars into 16 available) [-Wunterminated-string-initialization]
2618 | static char flash_cookie[2][16] = {"*** SE FLAS", "H DIRECTORY *** "};
| ^~~~~~~~~~~~~~~~~~
Add this annotation, avoid using a multidimensional array, but keep the
string split (with a comment about why). Additionally mark it const
and annotate the "cookie" member that is being memcmp()ed against as
nonstring too.
Signed-off-by: Kees Cook <kees@kernel.org>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/20250416221028.work.967-kees@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Use pci_prepare_to_sleep() like PCI core does in pci_pm_suspend_noirq.
This aligns setting a low-power mode during shutdown with the handling
of the transition to system suspend. Also the transition to runtime
suspend uses pci_target_state() instead of setting D3hot unconditionally.
Note: pci_prepare_to_sleep() uses device_may_wakeup() to check whether
device may generate wakeup events. So we don't lose anything by
not passing tp->saved_wolopts any longer.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Link: https://patch.msgid.link/f573fdbd-ba6d-41c1-b68f-311d3c88db2c@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
p8022.c defines two external functions, register_8022_client()
and unregister_8022_client(), the last use of which was removed in
2018 by
commit 7a2e838d28 ("staging: ipx: delete it from the tree")
Remove the p8022.c file, it's corresponding header, and glue
surrounding it. There was one place the header was included in vlan.c
but it didn't use the functions it declared.
There was a comment in net/802/Makefile about checking
against net/core/Makefile, but that's at least 20 years old and
there's no sign of net/core/Makefile mentioning it.
Signed-off-by: Dr. David Alan Gilbert <linux@treblig.org>
Link: https://patch.msgid.link/20250418011519.145320-1-linux@treblig.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Add support for the newer get_module_eeprom_by_page interface.
Only the upper half of the 256 byte page is available for
reading, and the firmware puts the two sections into the
extended sprom buffer, so a union is used over the extended
sprom buffer to make clear which page is to be accessed.
With get_module_eeprom_by_page implemented there is no need
for the older get_module_info or git_module_eeprom interfaces,
so remove them.
Reviewed-by: Brett Creeley <brett.creeley@amd.com>
Signed-off-by: Shannon Nelson <shannon.nelson@amd.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/20250415231317.40616-3-shannon.nelson@amd.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
