There are two problems with using regcache in this module.
The amplifier has 3 addressing levels (BOOK, PAGE, REG). The firmware
contains blocks that must be written to BOOK 0x8C. The regcache doesn't
know anything about BOOK, so regcache_sync writes invalid values to the
actual BOOK.
The module handles 2 or more separate amplifiers. The amplifiers have
different register values, and the module uses only one regmap/regcache
for all the amplifiers. The regcache_sync only writes the last amplifier
used.
The module successfully restores all the written register values (RC
profile, program, configuration, calibration) without regcache.
Remove regcache functions and set regmap cache_type to REGCACHE_NONE.
Link: https://lore.kernel.org/r/21a183b5a08cb23b193af78d4b1114cc59419272.1701906455.git.soyer@irl.hu/
Fixes: 5be27f1e3e ("ALSA: hda/tas2781: Add tas2781 HDA driver")
Acked-by: Mark Brown <broonie@kernel.org>
CC: stable@vger.kernel.org
Signed-off-by: Gergo Koteles <soyer@irl.hu>
Link: https://lore.kernel.org/r/491aeed0e2eecc3b704ec856f815db21bad3ba0e.1703202126.git.soyer@irl.hu
Signed-off-by: Takashi Iwai <tiwai@suse.de>
ASoC: Fixes for v6.7
Quite a big collection of fixes, as ever mostly in drivers. There's one
framework fix for the HDMI CODEC where it wasn't handling startup
properly for some controllers, and one new x86 quirk, but otherwise all
local fixes or dropping things we don't want to see in a release.
When flag mclk_with_tere and mclk_direction_output enabled,
The SAI transmitter or receiver will be enabled in very early
stage, that if FSL_SAI_xMR is set by previous case,
for example previous case is one channel, current case is
two channels, then current case started with wrong xMR in
the beginning, then channel swap happen.
The patch is to clear xMR in hw_free() to avoid such
channel swap issue.
Fixes: 3e4a826129 ("ASoC: fsl_sai: MCLK bind with TX/RX enable bit")
Signed-off-by: Shengjiu Wang <shengjiu.wang@nxp.com>
Reviewed-by: Daniel Baluta <daniel.baluta@nxp.com>
Link: https://msgid.link/r/1702953057-4499-1-git-send-email-shengjiu.wang@nxp.com
Signed-off-by: Mark Brown <broonie@kernel.org>
This make use of the CS35L41 HDA Property framework, which supports
laptops which do not have the _DSD properties in their ACPI.
Add configuration table to be able to use a generic function which allows
laptops to be supported just by adding an entry into the table.
Use configuration table function for existing system 103C89C6.
Signed-off-by: Stefan Binding <sbinding@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20231218151221.388745-2-sbinding@opensource.cirrus.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Some BYTCR x86 tablets with a rt5640 codec have the left and right channels
of their speakers swapped.
Add a new BYT_RT5640_SWAPPED_SPEAKERS quirk for this which sets
cfg-spk:swapped in the components string to let userspace know
about the swapping so that the UCM profile can configure the mixer
to correct this.
Enable this new quirk on the Medion Lifetab S10346 which has its
speakers swapped.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://msgid.link/r/20231217213221.49424-2-hdegoede@redhat.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Currently, cur_prog/cur_conf remains at the default value (-1), while
program 0 has been loaded into the amplifiers.
In the playback hook, tasdevice_tuning_switch tries to restore the
cur_prog/cur_conf. In the runtime_resume/system_resume,
tasdevice_prmg_load tries to load the cur_prog as well.
Set cur_prog and cur_conf to 0 if available in the firmware.
Fixes: 5be27f1e3e ("ALSA: hda/tas2781: Add tas2781 HDA driver")
CC: stable@vger.kernel.org
Signed-off-by: Gergo Koteles <soyer@irl.hu>
Link: https://lore.kernel.org/r/038add0bdca1f979cc7abcce8f24cbcd3544084b.1702596646.git.soyer@irl.hu
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Calling component_add starts loading the firmware, the callback function
writes the program to the amplifiers. If the module resets the
amplifiers after component_add, it happens that one of the amplifiers
does not work because the reset and program writing are interleaving.
Call tas2781_reset before component_add to ensure reliable
initialization.
Fixes: 5be27f1e3e ("ALSA: hda/tas2781: Add tas2781 HDA driver")
CC: stable@vger.kernel.org
Signed-off-by: Gergo Koteles <soyer@irl.hu>
Link: https://lore.kernel.org/r/4d23bf58558e23ee8097de01f70f1eb8d9de2d15.1702511246.git.soyer@irl.hu
Signed-off-by: Takashi Iwai <tiwai@suse.de>
If the module can load the RCA but not the firmware binary, it will call
the cleanup functions. Then unloading the module causes general
protection fault due to double free.
Do not call the cleanup functions in tasdev_fw_ready.
general protection fault, probably for non-canonical address
0x6f2b8a2bff4c8fec: 0000 [#1] PREEMPT SMP NOPTI
Call Trace:
<TASK>
? die_addr+0x36/0x90
? exc_general_protection+0x1c5/0x430
? asm_exc_general_protection+0x26/0x30
? tasdevice_config_info_remove+0x6d/0xd0 [snd_soc_tas2781_fmwlib]
tas2781_hda_unbind+0xaa/0x100 [snd_hda_scodec_tas2781_i2c]
component_unbind+0x2e/0x50
component_unbind_all+0x92/0xa0
component_del+0xa8/0x140
tas2781_hda_remove.isra.0+0x32/0x60 [snd_hda_scodec_tas2781_i2c]
i2c_device_remove+0x26/0xb0
Fixes: 5be27f1e3e ("ALSA: hda/tas2781: Add tas2781 HDA driver")
CC: stable@vger.kernel.org
Signed-off-by: Gergo Koteles <soyer@irl.hu>
Link: https://lore.kernel.org/r/1a0885c424bb21172702d254655882b59ef6477a.1702510018.git.soyer@irl.hu
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Alas on some headsets the bias sense can cause problems with the
type detection. It can occasionally be falsely triggered by the type
detect itself and as the clamp is applied when this happens, it will
cause a headset to be incorrectly identified as headphones. As
such it should be disabled whilst running type detect. This does
mean a jack removal during type detect will cause a larger click
but that is unfortunately unavoidable.
Fixes: 1e4ce0d5c0 ("ASoC: cs42l43: Move headset bias sense enable earlier in process")
Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Link: https://msgid.link/r/20231211160019.2034442-1-ckeepax@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Change the ALSA prefix for the CS35L56 to "AMPn".
This keeps them consistent with the CS35L56 HDA driver. It also
avoids coding the chip ID into the control name, so that other
Cirrus amps with the same controls can have the same control
names.
Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Fixes: 05fe628428 ("ASoC: Intel: soc-acpi-intel-mtl-match: add acpi match table for cdb35l56-eight-c")
Link: https://msgid.link/r/20231205115715.2460386-1-rf@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The code does not properly check whether the calibration variable is
available in the EFI. If it is not available, it causes a NULL pointer
dereference.
Check the return value of the first get_variable call also.
BUG: kernel NULL pointer dereference, address: 0000000000000000
Call Trace:
<TASK>
? __die+0x23/0x70
? page_fault_oops+0x171/0x4e0
? srso_alias_return_thunk+0x5/0x7f
? schedule+0x5e/0xd0
? exc_page_fault+0x7f/0x180
? asm_exc_page_fault+0x26/0x30
? crc32_body+0x2c/0x120
? tas2781_save_calibration+0xe4/0x220 [snd_hda_scodec_tas2781_i2c]
tasdev_fw_ready+0x1af/0x280 [snd_hda_scodec_tas2781_i2c]
request_firmware_work_func+0x59/0xa0
Fixes: 5be27f1e3e ("ALSA: hda/tas2781: Add tas2781 HDA driver")
CC: stable@vger.kernel.org
Signed-off-by: Gergo Koteles <soyer@irl.hu>
Link: https://lore.kernel.org/r/f1f6583bda918f78556f67d522ca7b3b91cebbd5.1702251102.git.soyer@irl.hu
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Stop timer in the 'trigger' and 'sync_stop' callbacks since we want
the timer to be stopped before the DMA buffer is released. Otherwise,
it could trigger a kernel panic in some circumstances, for instance
when the DMA buffer is already released but the timer callback is
still running.
Signed-off-by: Ivan Orlov <ivan.orlov0322@gmail.com>
Link: https://lore.kernel.org/r/20231206223211.12761-1-ivan.orlov0322@gmail.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Make use of the recently introduced EXPORT_GPL_DEV_PM_OPS() macro, to
conditionally export the runtime/system PM functions.
Replace the old SET_{RUNTIME,SYSTEM_SLEEP,NOIRQ_SYSTEM_SLEEP}_PM_OPS()
helpers with their modern alternatives and get rid of the now
unnecessary '__maybe_unused' annotations on all PM functions.
Additionally, use the pm_ptr() macro to fix the following errors when
building with CONFIG_PM disabled:
Signed-off-by: Ricardo Rivera-Matos <rriveram@opensource.cirrus.com>
Acked-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20231206160318.1255034-2-rriveram@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
ASoC: Fixes for v6.7
A crop of fixes for v6.7, one core fix for a merge issue and a bunch of
driver specific fixes and new IDs, mostly for x86 platforms.
Merge series from srinivas.kandagatla@linaro.org:
Limit the speaker digital gains to 0dB so that the users will not damage them.
Currently there is a limit in UCM, but this does not stop the user form
changing the digital gains from command line. So limit this in driver
which makes the speakers more safer without active speaker protection in
place.
Apart from this there is also a range check fix in snd_soc_limit_volume
to allow setting this limit correctly.
Tested on Lenovo X13s.
