Merge the mmc fixes for v6.11-rc[n] into the next branch, to allow them to
get tested together with the new mmc changes that are targeted for v6.12.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Commit 616f876617 ("mmc: pass queue_limits to blk_mq_alloc_disk") [1]
revealed the long living issue in dw_mmc.c driver, existing since the
time when it was first introduced in commit f95f3850f7 ("mmc: dw_mmc:
Add Synopsys DesignWare mmc host driver."), also making kernel boot
broken on platforms using dw_mmc driver with 16K or 64K pages enabled,
with this message in dmesg:
mmcblk: probe of mmc0:0001 failed with error -22
That's happening because mmc_blk_probe() fails when it calls
blk_validate_limits() consequently, which returns the error due to
failed max_segment_size check in this code:
/*
* The maximum segment size has an odd historic 64k default that
* drivers probably should override. Just like the I/O size we
* require drivers to at least handle a full page per segment.
*/
...
if (WARN_ON_ONCE(lim->max_segment_size < PAGE_SIZE))
return -EINVAL;
In case when IDMAC (Internal DMA Controller) is used, dw_mmc.c always
sets .max_seg_size to 4 KiB:
mmc->max_seg_size = 0x1000;
The comment in the code above explains why it's incorrect. Arnd
suggested setting .max_seg_size to .max_req_size to fix it, which is
also what some other drivers are doing:
$ grep -rl 'max_seg_size.*=.*max_req_size' drivers/mmc/host/ | \
wc -l
18
This change is not only fixing the boot with 16K/64K pages, but also
leads to a better MMC performance. The linear write performance was
tested on E850-96 board (eMMC only), before commit [1] (where it's
possible to boot with 16K/64K pages without this fix, to be able to do
a comparison). It was tested with this command:
# dd if=/dev/zero of=somefile bs=1M count=500 oflag=sync
Test results are as follows:
- 4K pages, .max_seg_size = 4 KiB: 94.2 MB/s
- 4K pages, .max_seg_size = .max_req_size = 512 KiB: 96.9 MB/s
- 16K pages, .max_seg_size = 4 KiB: 126 MB/s
- 16K pages, .max_seg_size = .max_req_size = 2 MiB: 128 MB/s
- 64K pages, .max_seg_size = 4 KiB: 138 MB/s
- 64K pages, .max_seg_size = .max_req_size = 8 MiB: 138 MB/s
Unfortunately, SD card controller is not enabled in E850-96 yet, so it
wasn't possible for me to run the test on some cheap SD cards to check
this patch's impact on those. But it's possible that this change might
also reduce the writes count, thus improving SD/eMMC longevity.
All credit for the analysis and the suggested solution goes to Arnd.
[1] https://lore.kernel.org/all/20240215070300.2200308-18-hch@lst.de/
Fixes: f95f3850f7 ("mmc: dw_mmc: Add Synopsys DesignWare mmc host driver.")
Suggested-by: Arnd Bergmann <arnd@arndb.de>
Reported-by: Linux Kernel Functional Testing <lkft@linaro.org>
Closes: https://lore.kernel.org/all/CA+G9fYtddf2Fd3be+YShHP6CmSDNcn0ptW8qg+stUKW+Cn0rjQ@mail.gmail.com/
Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20240306232052.21317-1-semen.protsenko@linaro.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Adds support in the OP-TEE drivers (both SMC and FF-A ABIs) to probe and
use an RPMB device via the RPMB subsystem instead of passing the RPMB
frames via tee-supplicant in user space. A fallback mechanism is kept to
route RPMB frames via tee-supplicant if the RPMB subsystem isn't
available.
The OP-TEE RPC ABI is extended to support iterating over all RPMB
devices until one is found with the expected RPMB key already
programmed.
Signed-off-by: Jens Wiklander <jens.wiklander@linaro.org>
Tested-by: Manuel Traut <manut@mecka.net>
Reviewed-by: Sumit Garg <sumit.garg@linaro.org>
Link: https://lore.kernel.org/r/20240814153558.708365-5-jens.wiklander@linaro.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Register eMMC RPMB partition with the RPMB subsystem and provide
an implementation for the RPMB access operations abstracting
the actual multi step process.
Add a callback to extract the needed device information at registration
to avoid accessing the struct mmc_card at a later stage as we're not
holding a reference counter for this struct.
Taking the needed reference to md->disk in mmc_blk_alloc_rpmb_part()
instead of in mmc_rpmb_chrdev_open(). This is needed by the
route_frames() function pointer in struct rpmb_ops.
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Alexander Usyskin <alexander.usyskin@intel.com>
Signed-off-by: Jens Wiklander <jens.wiklander@linaro.org>
Tested-by: Manuel Traut <manut@mecka.net>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
Link: https://lore.kernel.org/r/20240814153558.708365-3-jens.wiklander@linaro.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
A number of storage technologies support a specialised hardware
partition designed to be resistant to replay attacks. The underlying
HW protocols differ but the operations are common. The RPMB partition
cannot be accessed via standard block layer, but by a set of specific
RPMB commands. Such a partition provides authenticated and replay
protected access, hence suitable as a secure storage.
The initial aim of this patch is to provide a simple RPMB driver
interface which can be accessed by the optee driver to facilitate early
RPMB access to OP-TEE OS (secure OS) during the boot time.
A TEE device driver can claim the RPMB interface, for example, via
rpmb_interface_register() or rpmb_dev_find_device(). The RPMB driver
provides a callback to route RPMB frames to the RPMB device accessible
via rpmb_route_frames().
The detailed operation of implementing the access is left to the TEE
device driver itself.
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Alex Bennée <alex.bennee@linaro.org>
Signed-off-by: Shyam Saini <shyamsaini@linux.microsoft.com>
Signed-off-by: Jens Wiklander <jens.wiklander@linaro.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Tested-by: Manuel Traut <manut@mecka.net>
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Link: https://lore.kernel.org/r/20240814153558.708365-2-jens.wiklander@linaro.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Merge the mmc fixes for v6.11-rc[n] into the next branch, to allow them to
get tested together with the new mmc changes that are targeted for v6.12.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Applying MMC_QUIRK_BROKEN_SD_CACHE is broken, as the card's SD quirks are
referenced in sd_parse_ext_reg_perf() prior to the quirks being initialized
in mmc_blk_probe().
To fix this problem, let's split out an SD-specific list of quirks and
apply in mmc_sd_init_card() instead. In this way, sd_read_ext_regs() to has
the available information for not assigning the SD_EXT_PERF_CACHE as one of
the (un)supported features, which in turn allows mmc_sd_init_card() to
properly skip execution of sd_enable_cache().
Fixes: c467c8f081 ("mmc: Add MMC_QUIRK_BROKEN_SD_CACHE for Kingston Canvas Go Plus from 11/2019")
Signed-off-by: Jonathan Bell <jonathan@raspberrypi.com>
Co-developed-by: Keita Aihara <keita.aihara@sony.com>
Signed-off-by: Keita Aihara <keita.aihara@sony.com>
Reviewed-by: Dragan Simic <dsimic@manjaro.org>
Reviewed-by: Avri Altman <avri.altman@wdc.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20240820230631.GA436523@sony.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The local variable clk_ns uses at most 32 bits and can be a u32.
Replace the 64-by-32 do_div() division with a standard divison.
Since do_div() casts the divisor to u32 anyway, changing the data type
of clk_ns to u32 also removes the following Coccinelle/coccicheck
warning reported by do_div.cocci:
WARNING: do_div() does a 64-by-32 division, please consider using div64_u64 instead
Use min_t(u32,,) to simplify the code and improve its readability.
Signed-off-by: Thorsten Blum <thorsten.blum@toblux.com>
Link: https://lore.kernel.org/r/20240818142300.64156-2-thorsten.blum@toblux.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
SG2042 use Synopsys dwcnshc IP for SD/eMMC controllers.
SG2042 defines 3 clocks for SD/eMMC controllers.
- EMMC_100M/SD_100M for cclk(Card clocks in DWC_mshc), so reuse
existing "core".
- AXI_EMMC/AXI_SD for aclk/hclk(Bus interface clocks in DWC_mshc)
and blck(Core Base Clock in DWC_mshc), these 3 clocks share one
source, so reuse existing "bus".
- 100K_EMMC/100K_SD for cqetmclk(Timer clocks in DWC_mshc), so reuse
existing "timer" which was added for rockchip specified.
Signed-off-by: Chen Wang <unicorn_wang@outlook.com>
Reviewed-by: Conor Dooley <conor.dooley@microchip.com>
Link: https://lore.kernel.org/r/9ca450097e5389a38bcd7d8ddf863766df4cea10.1722847198.git.unicorn_wang@outlook.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The SD/MMC block on the RZ/V2H(P) ("R9A09G057") SoC is similar to that
of the R-Car Gen3, but it has some differences:
- HS400 is not supported.
- It has additional SD_STATUS register to control voltage,
power enable and reset.
- It supports fixed address mode.
To accommodate these differences, a SoC-specific 'renesas,sdhi-r9a09g057'
compatible string is added.
Note for RZ/V2H(P), we are using the `of_rzg2l_compatible` OF data as it
already handles no HS400 and fixed address mode support. Since the SDxIOVS
and SDxPWEN pins can always be used as GPIO pins on the RZ/V2H(P) SoC, no
driver changes are done to control the SD_STATUS register.
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Link: https://lore.kernel.org/r/20240724182119.652080-4-prabhakar.mahadev-lad.rj@bp.renesas.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Pull bcachefs fixes from Kent Overstreet:
- assorted syzbot fixes
- some upgrade fixes for old (pre 1.0) filesystems
- fix for moving data off a device that was switched to durability=0
after data had been written to it.
- nocow deadlock fix
- fix for new rebalance_work accounting
* tag 'bcachefs-2024-08-24' of git://evilpiepirate.org/bcachefs: (28 commits)
bcachefs: Fix rebalance_work accounting
bcachefs: Fix failure to flush moves before sleeping in copygc
bcachefs: don't use rht_bucket() in btree_key_cache_scan()
bcachefs: add missing inode_walker_exit()
bcachefs: clear path->should_be_locked in bch2_btree_key_cache_drop()
bcachefs: Fix double assignment in check_dirent_to_subvol()
bcachefs: Fix refcounting in discard path
bcachefs: Fix compat issue with old alloc_v4 keys
bcachefs: Fix warning in bch2_fs_journal_stop()
fs/super.c: improve get_tree() error message
bcachefs: Fix missing validation in bch2_sb_journal_v2_validate()
bcachefs: Fix replay_now_at() assert
bcachefs: Fix locking in bch2_ioc_setlabel()
bcachefs: fix failure to relock in btree_node_fill()
bcachefs: fix failure to relock in bch2_btree_node_mem_alloc()
bcachefs: unlock_long() before resort in journal replay
bcachefs: fix missing bch2_err_str()
bcachefs: fix time_stats_to_text()
bcachefs: Fix bch2_bucket_gens_init()
bcachefs: Fix bch2_trigger_alloc assert
...
Pull smb server fixes from Steve French:
- query directory flex array fix
- fix potential null ptr reference in open
- fix error message in some open cases
- two minor cleanups
* tag '6.11-rc5-server-fixes' of git://git.samba.org/ksmbd:
smb/server: update misguided comment of smb2_allocate_rsp_buf()
smb/server: remove useless assignment of 'file_present' in smb2_open()
smb/server: fix potential null-ptr-deref of lease_ctx_info in smb2_open()
smb/server: fix return value of smb2_open()
ksmbd: the buffer of smb2 query dir response has at least 1 byte
Pull s390 fixes from Vasily Gorbik:
- Fix KASLR base offset to account for symbol offsets in the vmlinux
ELF file, preventing tool breakages like the drgn debugger
- Fix potential memory corruption of physmem_info during kernel
physical address randomization
- Fix potential memory corruption due to overlap between the relocated
lowcore and identity mapping by correctly reserving lowcore memory
- Fix performance regression and avoid randomizing identity mapping
base by default
- Fix unnecessary delay of AP bus binding complete uevent to prevent
startup lag in KVM guests using AP
* tag 's390-6.11-4' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux:
s390/boot: Fix KASLR base offset off by __START_KERNEL bytes
s390/boot: Avoid possible physmem_info segment corruption
s390/ap: Refine AP bus bindings complete processing
s390/mm: Pin identity mapping base to zero
s390/mm: Prevent lowcore vs identity mapping overlap
Pull SCSI fixes from James Bottomley:
"The important core fix is another tweak to our discard discovery
issues. The off by 512 in logical block count seems bad, but in fact
the inline was only ever used in debug prints, which is why no-one
noticed"
* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
scsi: sd: Do not attempt to configure discard unless LBPME is set
scsi: MAINTAINERS: Add header files to SCSI SUBSYSTEM
scsi: ufs: qcom: Add UFSHCD_QUIRK_BROKEN_LSDBS_CAP for SM8550 SoC
scsi: ufs: core: Add a quirk for handling broken LSDBS field in controller capabilities register
scsi: core: Fix the return value of scsi_logical_block_count()
scsi: MAINTAINERS: Update HiSilicon SAS controller driver maintainer
rebalance_work was keying off of the presence of rebelance_opts in the
extent - but that was incorrect, we keep those around after rebalance
for indirect extents since the inode's options are not directly
available
Fixes: 20ac515a9c ("bcachefs: bch_acct_rebalance_work")
Signed-off-by: Kent Overstreet <kent.overstreet@linux.dev>
This fixes an apparent deadlock - rebalance would get stuck trying to
take nocow locks because they weren't being released by copygc.
Signed-off-by: Kent Overstreet <kent.overstreet@linux.dev>
Pull cgroup fixes from Tejun Heo:
"Three patches addressing cpuset corner cases"
* tag 'cgroup-for-6.11-rc4-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/cgroup:
cgroup/cpuset: Eliminate unncessary sched domains rebuilds in hotplug
cgroup/cpuset: Clear effective_xcpus on cpus_allowed clearing only if cpus.exclusive not set
cgroup/cpuset: fix panic caused by partcmd_update
Pull workqueue fixes from Tejun Heo:
"Nothing too interesting. One patch to remove spurious warning and
others to address static checker warnings"
* tag 'wq-for-6.11-rc4-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/wq:
workqueue: Correct declaration of cpu_pwq in struct workqueue_struct
workqueue: Fix spruious data race in __flush_work()
workqueue: Remove incorrect "WARN_ON_ONCE(!list_empty(&worker->entry));" from dying worker
workqueue: Fix UBSAN 'subtraction overflow' error in shift_and_mask()
workqueue: doc: Fix function name, remove markers
Pull MIPS fixes from Thomas Bogendoerfer:
- Set correct timer mode on Loongson64
- Only request r4k clockevent interrupt on one CPU
* tag 'mips-fixes_6.11_1' of git://git.kernel.org/pub/scm/linux/kernel/git/mips/linux:
MIPS: cevt-r4k: Don't call get_c0_compare_int if timer irq is installed
MIPS: Loongson64: Set timer mode in cpu-probe
Pull arm64 kvm fixes from Catalin Marinas:
- Don't drop references on LPIs that weren't visited by the vgic-debug
iterator
- Cure lock ordering issue when unregistering vgic redistributors
- Fix for misaligned stage-2 mappings when VMs are backed by hugetlb
pages
- Treat SGI registers as UNDEFINED if a VM hasn't been configured for
GICv3
* tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux:
KVM: arm64: Make ICC_*SGI*_EL1 undef in the absence of a vGICv3
KVM: arm64: Ensure canonical IPA is hugepage-aligned when handling fault
KVM: arm64: vgic: Don't hold config_lock while unregistering redistributors
KVM: arm64: vgic-debug: Don't put unmarked LPIs
Pull NFS client fixes from Anna Schumaker:
- Fix rpcrdma refcounting in xa_alloc
- Fix rpcrdma usage of XA_FLAGS_ALLOC
- Fix requesting FATTR4_WORD2_OPEN_ARGUMENTS
- Fix attribute bitmap decoder to handle a 3rd word
- Add reschedule points when returning delegations to avoid soft lockups
- Fix clearing layout segments in layoutreturn
- Avoid unnecessary rescanning of the per-server delegation list
* tag 'nfs-for-6.11-2' of git://git.linux-nfs.org/projects/anna/linux-nfs:
NFS: Avoid unnecessary rescanning of the per-server delegation list
NFSv4: Fix clearing of layout segments in layoutreturn
NFSv4: Add missing rescheduling points in nfs_client_return_marked_delegations
nfs: fix bitmap decoder to handle a 3rd word
nfs: fix the fetch of FATTR4_OPEN_ARGUMENTS
rpcrdma: Trace connection registration and unregistration
rpcrdma: Use XA_FLAGS_ALLOC instead of XA_FLAGS_ALLOC1
rpcrdma: Device kref is over-incremented on error from xa_alloc
Pull smb client fixes from Steve French:
- fix refcount leak (can cause rmmod fail)
- fix byte range locking problem with cached reads
- fix for mount failure if reparse point unrecognized
- minor typo
* tag 'v6.11-rc4-client-fixes' of git://git.samba.org/sfrench/cifs-2.6:
smb/client: fix typo: GlobalMid_Sem -> GlobalMid_Lock
smb: client: ignore unhandled reparse tags
smb3: fix problem unloading module due to leaked refcount on shutdown
smb3: fix broken cached reads when posix locks
Pull input fixes from Dmitry Torokhov:
- a tweak to uinput interface to reject requests with abnormally large
number of slots. 100 slots/contacts should be enough for real devices
- support for FocalTech FT8201 added to the edt-ft5x06 driver
- tweaks to i8042 to handle more devices that have issue with its
emulation
- Synaptics touchpad switched to native SMbus/RMI mode on HP Elitebook
840 G2
- other minor fixes
* tag 'input-for-v6.11-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: himax_hx83112b - fix incorrect size when reading product ID
Input: i8042 - use new forcenorestore quirk to replace old buggy quirk combination
Input: i8042 - add forcenorestore quirk to leave controller untouched even on s3
Input: i8042 - add Fujitsu Lifebook E756 to i8042 quirk table
Input: uinput - reject requests with unreasonable number of slots
Input: edt-ft5x06 - add support for FocalTech FT8201
dt-bindings: input: touchscreen: edt-ft5x06: Document FT8201 support
Input: adc-joystick - fix optional value handling
Input: synaptics - enable SMBus for HP Elitebook 840 G2
Input: ads7846 - ratelimit the spi_sync error message
Pull drm fixes from Dave Airlie:
"Weekly fixes. xe and msm are the major groups, with
amdgpu/i915/nouveau having smaller bits. xe has a bunch of hw
workaround fixes that were found to be missing, so that is why there
are a bunch of scattered fixes, and one larger one. But overall size
doesn't look too out of the ordinary.
msm:
- virtual plane fixes:
- drop yuv on hw where not supported
- csc vs yuv format fix
- rotation fix
- fix fb cleanup on close
- reset phy before link training
- fix visual corruption at 4K
- fix NULL ptr crash on hotplug
- simplify debug macros
- sc7180 fix
- adreno firmware name error path fix
amdgpu:
- GFX10 firmware loading fix
- SDMA 5.2 fix
- Debugfs parameter validation fix
- eGPU hotplug fix
i915:
- fix HDCP timeouts
nouveau:
- fix SG_DEBUG crash
xe:
- Fix OA format masks which were breaking build with gcc-5
- Fix opregion leak (Lucas)
- Fix OA sysfs entry (Ashutosh)
- Fix VM dma-resv lock (Brost)
- Fix tile fini sequence (Brost)
- Prevent UAF around preempt fence (Auld)
- Fix DGFX display suspend/resume (Maarten)
- Many Xe/Xe2 critical workarounds (Auld, Ngai-Mint, Bommu, Tejas, Daniele)
- Fix devm/drmm issues (Daniele)
- Fix missing workqueue destroy in xe_gt_pagefault (Stuart)
- Drop HW fence pointer to HW fence ctx (Brost)
- Free job before xe_exec_queue_put (Brost)"
* tag 'drm-fixes-2024-08-24' of https://gitlab.freedesktop.org/drm/kernel: (35 commits)
drm/xe: Free job before xe_exec_queue_put
drm/xe: Drop HW fence pointer to HW fence ctx
drm/xe: Fix missing workqueue destroy in xe_gt_pagefault
drm/amdgpu: fix eGPU hotplug regression
drm/amdgpu: Validate TA binary size
drm/amdgpu/sdma5.2: limit wptr workaround to sdma 5.2.1
drm/amdgpu: fixing rlc firmware loading failure issue
drm/xe/uc: Use devm to register cleanup that includes exec_queues
drm/xe: use devm instead of drmm for managed bo
drm/xe/xe2hpg: Add Wa_14021821874
drm/xe: fix WA 14018094691
drm/xe/xe2: Add Wa_15015404425
drm/xe/xe2: Make subsequent L2 flush sequential
drm/xe/xe2lpg: Extend workaround 14021402888
drm/xe/xe2lpm: Extend Wa_16021639441
drm/xe/bmg: implement Wa_16023588340
drm/xe/oa/uapi: Make bit masks unsigned
drm/xe/display: Make display suspend/resume work on discrete
drm/xe: prevent UAF around preempt fence
drm/xe: Fix tile fini sequence
...
Pull block fixes from Jens Axboe:
- NVMe pull request via Keith
- Remove unused struct field (Nilay)
- Fix fabrics keep-alive teardown order (Ming)
- Write zeroes fixes (John)
* tag 'block-6.11-20240823' of git://git.kernel.dk/linux:
nvme: Remove unused field
nvme: move stopping keep-alive into nvme_uninit_ctrl()
block: Drop NULL check in bdev_write_zeroes_sectors()
block: Read max write zeroes once for __blkdev_issue_write_zeroes()
Pull io_uring fix from Jens Axboe:
"Just a single fix for provided buffer validation"
* tag 'io_uring-6.11-20240823' of git://git.kernel.dk/linux:
io_uring/kbuf: sanitize peek buffer setup
Pull ACPI fix from Rafael Wysocki:
"Fix backlight control on a Dell All In One system where a backlight
controller board is attached to a UART port and the dell-uart
backlight driver binds to it, but the backlight is actually controlled
by other means (Hans de Goede)"
* tag 'acpi-6.11-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
ACPI: video: Add backlight=native quirk for Dell OptiPlex 7760 AIO
platform/x86: dell-uart-backlight: Use acpi_video_get_backlight_type()
ACPI: video: Add Dell UART backlight controller detection
Pull thermal control fixes from Rafael Wysocki:
"These fix error handling in the thermal debug code and OF node
reference leaks in the thermal OF driver.
Specifics:
- Use IS_ERR() in checks of debugfs_create_dir() return value instead
of checking it against NULL in the thermal debug code (Yang Ruibin)
- Fix three OF node reference leaks in thermal_of (Krzysztof
Kozlowski)"
* tag 'thermal-6.11-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
thermal: of: Fix OF node leak in of_thermal_zone_find() error paths
thermal: of: Fix OF node leak in thermal_of_zone_register()
thermal: of: Fix OF node leak in thermal_of_trips_init() error path
thermal/debugfs: Fix the NULL vs IS_ERR() confusion in debugfs_create_dir()
Pull mmc fixes from Ulf Hansson:
"MMC core:
- Fix NULL dereference for mmc_test on allocation failure
MMC host:
- dw_mmc: Fix support for deferred probe for biu/ciu clocks
- mtk-sd: Fix CMD8 support when fragile tuning settings"
* tag 'mmc-v6.11-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc:
mmc: mmc_test: Fix NULL dereference on allocation failure
mmc: dw_mmc: allow biu and ciu clocks to defer
mmc: mtk-sd: receive cmd8 data when hs400 tuning fail
Pull spi fixes from Mark Brown:
"A small collection of fixes here, all driver specific and none of them
too serious. For whatever reason runtime PM seems to have been causing
a bunch of issues recently"
* tag 'spi-fix-v6.11-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi:
spi: pxa2xx: Move PM runtime handling to the glue drivers
spi: pxa2xx: Do not override dev->platform_data on probe
spi: spi-fsl-lpspi: limit PRESCALE bit in TCR register
spi: spi-cadence-quadspi: Fix OSPI NOR failures during system resume
spi: zynqmp-gqspi: Scale timeout by data size
