When firmware crashed while channel switch running, recovery starts in
ath12k. Then ieee80211_sta_connection_lost() will be called by function
ieee80211_restart_work() in mac80211. And then many WMI command timeout
because firmware is crashed. Each WMI command cost 3 seconds, then the
total time will be large and leads recovery fail.
Hence change to set value ATH12K_FLAG_CRASH_FLUSH early and then
ath12k_wmi_cmd_send() will not wait 3 seconds, then recovery will be
started quickly and success.
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0-03427-QCAHMTSWPL_V1.0_V2.0_SILICONZ-1.15378.4
Signed-off-by: Wen Gong <quic_wgong@quicinc.com>
Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20230905105229.10090-1-quic_wgong@quicinc.com
When hardware rfkill is enabled in the firmware, it will report the
capability using WMI_SYS_CAP_INFO_RFKILL bit in the WMI_SERVICE_READY event
to the host. Currently ath12k does not process this service capability. In
order to support this, update ath12k to check if the capability is enabled,
if so, send the GPIO information to firmware. When the firmware detects
hardware rfkill is enabled by the user, it will report it using
WMI_RFKILL_STATE_CHANGE_EVENTID. When ath12k receive the event, it will set
the value of rfkill_radio_on based on whether radio_state is equal to
WMI_RFKILL_RADIO_STATE_ON, then send WMI_PDEV_PARAM_RFKILL_ENABLE to
firmware.
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0-03427-QCAHMTSWPL_V1.0_V2.0_SILICONZ-1.15378.4
Signed-off-by: Lingbo Kong <quic_lingbok@quicinc.com>
Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20230906110412.182176-1-quic_lingbok@quicinc.com
In 'ath11k_dp_rx_mon_dest_process()', 'mon_dst_srng' points to
a member of 'srng_list', which is a fixed-size array inside
'struct ath11k_hal'. This way, if 'ring_id' is valid (i. e.
between 0 and HAL_SRNG_RING_ID_MAX - 1 inclusive), 'mon_dst_srng'
can't be NULL and so relevant check may be dropped.
Found by Linux Verification Center (linuxtesting.org) with SVACE.
Signed-off-by: Dmitry Antipov <dmantipov@yandex.ru>
Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20230824075121.121144-1-dmantipov@yandex.ru
Commit 5b32b6dd96 ("ath11k: Remove core PCI references from
PCI common code") breaks with one MSI vector because it moves
affinity setting after IRQ request, see below log:
[ 1417.278835] ath11k_pci 0000:02:00.0: failed to receive control response completion, polling..
[ 1418.302829] ath11k_pci 0000:02:00.0: Service connect timeout
[ 1418.302833] ath11k_pci 0000:02:00.0: failed to connect to HTT: -110
[ 1418.303669] ath11k_pci 0000:02:00.0: failed to start core: -110
The detail is, if do affinity request after IRQ activated,
which is done in request_irq(), kernel caches that request and
returns success directly. Later when a subsequent MHI interrupt is
fired, kernel will do the real affinity setting work, as a result,
changs the MSI vector. However at that time host has configured
old vector to hardware, so host never receives CE or DP interrupts.
Fix it by setting affinity before registering MHI controller
where host is, for the first time, doing IRQ request.
Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-03125-QCAHSPSWPL_V1_V2_SILICONZ_LITE-3
Tested-on: WCN6855 hw2.1 PCI WLAN.HSP.1.1-03125-QCAHSPSWPL_V1_V2_SILICONZ_LITE-3.6510.23
Tested-on: WCN6750 hw1.0 AHB WLAN.MSL.1.0.1-01160-QCAMSLSWPLZ-1
Fixes: 5b32b6dd96 ("ath11k: Remove core PCI references from PCI common code")
Signed-off-by: Baochen Qiang <quic_bqiang@quicinc.com>
Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20230907015606.16297-1-quic_bqiang@quicinc.com
In ath9k_hif_usb_resume, the error handling code calls
ath9k_hif_usb_dealloc_urbs twice in different paths.
To unify the error handling code, we move the else branch before
the if branch and drop one level of indentation of the if branch.
In addition, move the ret variable at the end of variable declarations
to be reverse x-mas tree order.
Note that this patch does not incur any functionability change.
Signed-off-by: Dongliang Mu <dzm91@hust.edu.cn>
Reviewed-by: Dan Carpenter <dan.carpenter@linaro.org>
Acked-by: Toke Høiland-Jørgensen <toke@toke.dk>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20230905013556.2595854-1-dzm91@hust.edu.cn
In ath12k_dp_tx(), if we reach fail_dma_unmap due to some errors,
current code does DMA unmap unconditionally on skb_cb->paddr_ext_desc.
However, skb_cb->paddr_ext_desc may be NULL and thus we get below
warning:
kernel: [ 8887.076212] WARNING: CPU: 3 PID: 0 at drivers/iommu/dma-iommu.c:1077 iommu_dma_unmap_page+0x79/0x90
Fix it by checking skb_cb->paddr_ext_desc before unmap it.
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0-03427-QCAHMTSWPL_V1.0_V2.0_SILICONZ-1.15378.4
Fixes: d889913205 ("wifi: ath12k: driver for Qualcomm Wi-Fi 7 devices")
Signed-off-by: Baochen Qiang <quic_bqiang@quicinc.com>
Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20230830021131.5610-1-quic_bqiang@quicinc.com
When compiling with clang 16.0.6 and CONFIG_FORTIFY_SOURCE=y, I've
noticed the following (somewhat confusing due to absence of an actual
source code location):
In file included from drivers/net/wireless/ath/ath10k/debug.c:8:
In file included from ./include/linux/module.h:13:
In file included from ./include/linux/stat.h:19:
In file included from ./include/linux/time.h:60:
In file included from ./include/linux/time32.h:13:
In file included from ./include/linux/timex.h:67:
In file included from ./arch/x86/include/asm/timex.h:5:
In file included from ./arch/x86/include/asm/processor.h:23:
In file included from ./arch/x86/include/asm/msr.h:11:
In file included from ./arch/x86/include/asm/cpumask.h:5:
In file included from ./include/linux/cpumask.h:12:
In file included from ./include/linux/bitmap.h:11:
In file included from ./include/linux/string.h:254:
./include/linux/fortify-string.h:592:4: warning: call to '__read_overflow2_field'
declared with 'warning' attribute: detected read beyond size of field (2nd
parameter); maybe use struct_group()? [-Wattribute-warning]
__read_overflow2_field(q_size_field, size);
The compiler actually complains on 'ath10k_debug_get_et_strings()' where
fortification logic inteprets call to 'memcpy()' as an attempt to copy
the whole 'ath10k_gstrings_stats' array from it's first member and so
issues an overread warning. This warning may be silenced by passing
an address of the whole array and not the first member to 'memcpy()'.
Signed-off-by: Dmitry Antipov <dmantipov@yandex.ru>
Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20230829093652.234537-1-dmantipov@yandex.ru
Sometimes board-2.bin does not have the board data which matched the
parameters such as bus type, vendor, device, subsystem-vendor,
subsystem-device, qmi-chip-id and qmi-board-id, then wlan will load fail.
Hence add another type which only matches the bus type and qmi-chip-id,
then the ratio of missing board data reduced.
Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-03125-QCAHSPSWPL_V1_V2_SILICONZ_LITE-3.6510.23
Signed-off-by: Wen Gong <quic_wgong@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20230830060226.18664-1-quic_wgong@quicinc.com
len is extracted from HTT message and could be an unexpected value in
case errors happen, so add validation before using to avoid possible
out-of-bound read in the following message iteration and parsing.
The same issue also applies to ppdu_info->ppdu_stats.common.num_users,
so validate it before using too.
These are found during code review.
Compile test only.
Signed-off-by: Baochen Qiang <quic_bqiang@quicinc.com>
Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20230901015602.45112-1-quic_bqiang@quicinc.com
Sometimes device recovery fail with this operation.
Run test command for many times:
echo assert > /sys/kernel/debug/ath12k/wcn7850\ hw2.0_0000\:03\:00.0/simulate_fw_crash
While recovery start, ath12k_core_post_reconfigure_recovery() will
call ieee80211_restart_hw(), and the restart_work which queued by
ieee80211_restart_hw() is running in another thread, it will call
into ath12k_mac_op_start() and ath12k_mac_wait_reconfigure(), and
the variables ab->recovery_start_count and ab->recovery_start is used
in ath12k_mac_wait_reconfigure(), so ath12k need to initialize the
variables before queue the restart_work, otherwise ath12k_mac_wait_reconfigure()
maybe use the un-initialized variables. Change to initialize the 2
variables earlier and then recovery process become correct.
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0-03427-QCAHMTSWPL_V1.0_V2.0_SILICONZ-1.15378.4
Signed-off-by: Wen Gong <quic_wgong@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20230830060850.18881-1-quic_wgong@quicinc.com
320 MHz bandwidth is reported only for single PHY mode for WCN7850, get it
from WMI_HOST_HW_MODE_SINGLE ath12k_wmi_caps_ext_params and report it for
6 GHz band.
After this patch, "iw list" shows 320 MHz support for WCN7850:
EHT Iftypes: managed
EHT PHY Capabilities: (0xe26f090010768800):
320MHz in 6GHz Supported
EHT bw=320 MHz, max NSS for MCS 8-9: Rx=0, Tx=0
EHT bw=320 MHz, max NSS for MCS 10-11: Rx=0, Tx=0
EHT bw=320 MHz, max NSS for MCS 12-13: Rx=0, Tx=0
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0-03427-QCAHMTSWPL_V1.0_V2.0_SILICONZ-1.15378.4
Signed-off-by: Wen Gong <quic_wgong@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20230828040420.2165-1-quic_wgong@quicinc.com
When compiling with clang 16.0.6 and CONFIG_FORTIFY_SOURCE=y, I've
noticed the following (somewhat confusing due to absence of an actual
source code location):
In file included from drivers/net/wireless/ath/ath9k/debug.c:17:
In file included from ./include/linux/slab.h:16:
In file included from ./include/linux/gfp.h:7:
In file included from ./include/linux/mmzone.h:8:
In file included from ./include/linux/spinlock.h:56:
In file included from ./include/linux/preempt.h:79:
In file included from ./arch/x86/include/asm/preempt.h:9:
In file included from ./include/linux/thread_info.h:60:
In file included from ./arch/x86/include/asm/thread_info.h:53:
In file included from ./arch/x86/include/asm/cpufeature.h:5:
In file included from ./arch/x86/include/asm/processor.h:23:
In file included from ./arch/x86/include/asm/msr.h:11:
In file included from ./arch/x86/include/asm/cpumask.h:5:
In file included from ./include/linux/cpumask.h:12:
In file included from ./include/linux/bitmap.h:11:
In file included from ./include/linux/string.h:254:
./include/linux/fortify-string.h:592:4: warning: call to '__read_overflow2_field'
declared with 'warning' attribute: detected read beyond size of field (2nd
parameter); maybe use struct_group()? [-Wattribute-warning]
__read_overflow2_field(q_size_field, size);
In file included from drivers/net/wireless/ath/ath9k/htc_drv_debug.c:17:
In file included from drivers/net/wireless/ath/ath9k/htc.h:20:
In file included from ./include/linux/module.h:13:
In file included from ./include/linux/stat.h:19:
In file included from ./include/linux/time.h:60:
In file included from ./include/linux/time32.h:13:
In file included from ./include/linux/timex.h:67:
In file included from ./arch/x86/include/asm/timex.h:5:
In file included from ./arch/x86/include/asm/processor.h:23:
In file included from ./arch/x86/include/asm/msr.h:11:
In file included from ./arch/x86/include/asm/cpumask.h:5:
In file included from ./include/linux/cpumask.h:12:
In file included from ./include/linux/bitmap.h:11:
In file included from ./include/linux/string.h:254:
./include/linux/fortify-string.h:592:4: warning: call to '__read_overflow2_field'
declared with 'warning' attribute: detected read beyond size of field (2nd
parameter); maybe use struct_group()? [-Wattribute-warning]
__read_overflow2_field(q_size_field, size);
The compiler actually complains on 'ath9k_get_et_strings()' and
'ath9k_htc_get_et_strings()' due to the same reason: fortification logic
inteprets call to 'memcpy()' as an attempt to copy the whole array from
it's first member and so issues an overread warning. These warnings may
be silenced by passing an address of the whole array and not the first
member to 'memcpy()'.
Signed-off-by: Dmitry Antipov <dmantipov@yandex.ru>
Acked-by: Toke Høiland-Jørgensen <toke@toke.dk>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20230829093856.234584-1-dmantipov@yandex.ru
Since commit 8896934c16 ("ath9k_hw: remove direct accesses to channel
mode flags") changes 'ar9550_hw_get_modes_txgain_index()' so it never
returns -EINVAL, and 'ar9561_hw_get_modes_txgain_index()' never returns
negative value too, an extra check in 'ar9003_hw_process_ini()' may be
dropped.
Found by Linux Verification Center (linuxtesting.org) with SVACE.
Signed-off-by: Dmitry Antipov <dmantipov@yandex.ru>
Reviewed-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Acked-by: Toke Høiland-Jørgensen <toke@toke.dk>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20230823182401.196270-1-dmantipov@yandex.ru
Radar detection fails in the secondary 80 MHz when the
the AP's primary 80 MHz is in non-DFS region in 160 MHz.
This is due to WMI channel flag WMI_CHAN_INFO_DFS_FREQ2 is not set
properly in case of the primary 80 MHz is in non-DFS region.
HALPHY detects the radar pulses in the secondary 80 MHz only when
WMI_CHAN_INFO_DFS_FREQ2 is set.
Fix this issue by setting WMI channel flag WMI_CHAN_INFO_DFS_FREQ2
based on the radar_enabled flag from the channel context.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.0.1-00029-QCAHKSWPL_SILICONZ-1
Signed-off-by: Manish Dharanenthiran <quic_mdharane@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20230802085852.19821-3-quic_mdharane@quicinc.com
When max virtual ap interfaces are configured in all the bands
with ACS and hostapd restart is done every 60s,
a crash is observed at random times because of handling the
uninitialized peer fragments with fragment id of packet as 0.
"__fls" would have an undefined behavior if the argument is passed
as "0". Hence, added changes to handle the same.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.0.1-00029-QCAHKSWPL_SILICONZ-1
Fixes: d889913205 ("wifi: ath12k: driver for Qualcomm Wi-Fi 7 devices")
Signed-off-by: Harshitha Prem <quic_hprem@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20230821130343.29495-3-quic_hprem@quicinc.com
When max virtual ap interfaces are configured in all the bands with
ACS and hostapd restart is done every 60s, a crash is observed at
random times.
In the above scenario, a fragmented packet is received for self peer,
for which rx_tid and rx_frags are not initialized in datapath.
While handling this fragment, crash is observed as the rx_frag list
is uninitialized and when we walk in ath12k_dp_rx_h_sort_frags,
skb null leads to exception.
To address this, before processing received fragments we check
dp_setup_done flag is set to ensure that peer has completed its
dp peer setup for fragment queue, else ignore processing the
fragments.
Call trace:
PC points to "ath12k_dp_process_rx_err+0x4e8/0xfcc [ath12k]"
LR points to "ath12k_dp_process_rx_err+0x480/0xfcc [ath12k]".
The Backtrace obtained is as follows:
ath12k_dp_process_rx_err+0x4e8/0xfcc [ath12k]
ath12k_dp_service_srng+0x78/0x260 [ath12k]
ath12k_pci_write32+0x990/0xb0c [ath12k]
__napi_poll+0x30/0xa4
net_rx_action+0x118/0x270
__do_softirq+0x10c/0x244
irq_exit+0x64/0xb4
__handle_domain_irq+0x88/0xac
gic_handle_irq+0x74/0xbc
el1_irq+0xf0/0x1c0
arch_cpu_idle+0x10/0x18
do_idle+0x104/0x248
cpu_startup_entry+0x20/0x64
rest_init+0xd0/0xdc
arch_call_rest_init+0xc/0x14
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.0.1-00029-QCAHKSWPL_SILICONZ-1
Signed-off-by: Harshitha Prem <quic_hprem@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20230821130343.29495-2-quic_hprem@quicinc.com
Currently, the ath11k driver does not print a crash signature when a
MHI_CB_EE_RDDM crash happens. Checked by triggering a simulated crash using the
command and checking dmesg for logs:
echo assert > /sys/kernel/debug/ath11k/../simulate_fw_crash
Add a warning when firmware crash MHI_CB_EE_RDDM happens.
Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-03125-QCAHSPSWPL_V1_V2_SILICONZ_LITE-3.6510.23
Signed-off-by: Arowa Suliman <arowa@chromium.org>
Reviewed-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20230714001126.463127-1-arowa@chromium.org
Tony Nguyen says:
====================
Intel Wired LAN Driver Updates 2023-08-24 (igc, e1000e)
This series contains updates to igc and e1000e drivers.
Vinicius adds support for utilizing multiple PTP registers on igc.
Sasha reduces interval time for PTM on igc and adds new device support
on e1000e.
* '1GbE' of git://git.kernel.org/pub/scm/linux/kernel/git/tnguy/next-queue:
e1000e: Add support for the next LOM generation
igc: Decrease PTM short interval from 10 us to 1 us
igc: Add support for multiple in-flight TX timestamps
====================
Link: https://lore.kernel.org/r/20230824204418.1551093-1-anthony.l.nguyen@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
We use a tempfile for code generation, to avoid wiping the target
file out if the code generator crashes. File contents are copied
from tempfile to actual destination at the end of main().
uAPI generation is relatively simple so when generating the uAPI
header we return from main() early, and never reach the "copy code
over" stage. Since commit under Fixes uAPI headers are not updated
by ynl-gen.
Move the copy/commit of the code into CodeWriter, to make it
easier to call at any point in time. Hook it into the destructor
to make sure we don't miss calling it.
Fixes: f65f305ae0 ("tools: ynl-gen: use temporary file for rendering")
Link: https://lore.kernel.org/r/20230824212431.1683612-1-kuba@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Russell King says:
====================
stmmac cleanups
One of the comments I had on Feiyang Chen's series was concerning the
initialisation of phylink... and so I've decided to do something about
it, cleaning it up a bit.
This series:
1) adds a new phylink function to limit the MAC capabilities according
to a maximum speed. This allows us to greatly simplify stmmac's
initialisation of phylink's mac capabilities.
2) everywhere that uses priv->plat->phylink_node first converts this
to a fwnode before doing anything with it. This is silly. Let's
instead store it as a fwnode to eliminate these conversions in
multiple places.
3) clean up passing the fwnode to phylink - it might as well happen
at the phylink_create() callsite, rather than being scattered
throughout the entire function.
4) same for mdio_bus_data
5) use phylink_limit_mac_speed() to handle the priv->plat->max_speed
restriction.
6) add a method to get the MAC-specific capabilities from the code
dealing with the MACs, and arrange to call it at an appropriate
time.
7) convert the gmac4 users to use the MAC specific method.
8) same for xgmac.
9) group all the simple phylink_config initialisations together.
10) convert half-duplex logic to being positive logic.
While looking into all of this, this raised eyebrows:
if (priv->plat->tx_queues_to_use > 1)
priv->phylink_config.mac_capabilities &=
~(MAC_10HD | MAC_100HD | MAC_1000HD);
priv->plat->tx_queues_to_use is initialised by platforms to either 1,
4 or 8, and can be controlled from userspace via the --set-channels
ethtool op. The implementation of this op in this driver limits the
number of channels to priv->dma_cap.number_tx_queues, which is derived
from the DMA hwcap.
So, the obvious questions are:
1) what guarantees that the static initialisation of tx_queues_to_use
will always be less than or equal to number_tx_queues from the DMA hw
cap?
2) tx_queues_to_use starts off as 1, but number_tx_queues is larger,
we will leave the half-duplex capabilities in place, but userspace can
increase tx_queues_to_use above 1. Does that mean half-duplex is then
not supported?
3) Should we be basing the decision whether half-duplex is supported
off the DMA capabilities?
4) What about priv->dma_cap.half_duplex? Doesn't that get a say in
whether half-duplex is supported or not? Why isn't this used? Why is
it only reported via debugfs? If it's not being used by the driver,
what's the point of reporting it via debugfs?
====================
Link: https://lore.kernel.org/r/ZOddFH22PWmOmbT5@shell.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
We have a local variable for priv->plat->mdio_bus_data, which we use
later in the conditional if() block, but we evaluate the above within
the conditional expression. Use mdio_bus_data instead. Since these
will be the only two users of this local variable, move its assignment
just before the if().
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Link: https://lore.kernel.org/r/E1qZAXJ-005pU1-1z@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Daniel Borkmann says:
====================
pull-request: bpf-next 2023-08-25
We've added 87 non-merge commits during the last 8 day(s) which contain
a total of 104 files changed, 3719 insertions(+), 4212 deletions(-).
The main changes are:
1) Add multi uprobe BPF links for attaching multiple uprobes
and usdt probes, which is significantly faster and saves extra fds,
from Jiri Olsa.
2) Add support BPF cpu v4 instructions for arm64 JIT compiler,
from Xu Kuohai.
3) Add support BPF cpu v4 instructions for riscv64 JIT compiler,
from Pu Lehui.
4) Fix LWT BPF xmit hooks wrt their return values where propagating
the result from skb_do_redirect() would trigger a use-after-free,
from Yan Zhai.
5) Fix a BPF verifier issue related to bpf_kptr_xchg() with local kptr
where the map's value kptr type and locally allocated obj type
mismatch, from Yonghong Song.
6) Fix BPF verifier's check_func_arg_reg_off() function wrt graph
root/node which bypassed reg->off == 0 enforcement,
from Kumar Kartikeya Dwivedi.
7) Lift BPF verifier restriction in networking BPF programs to treat
comparison of packet pointers not as a pointer leak,
from Yafang Shao.
8) Remove unmaintained XDP BPF samples as they are maintained
in xdp-tools repository out of tree, from Toke Høiland-Jørgensen.
9) Batch of fixes for the tracing programs from BPF samples in order
to make them more libbpf-aware, from Daniel T. Lee.
10) Fix a libbpf signedness determination bug in the CO-RE relocation
handling logic, from Andrii Nakryiko.
11) Extend libbpf to support CO-RE kfunc relocations. Also follow-up
fixes for bpf_refcount shared ownership implementation,
both from Dave Marchevsky.
12) Add a new bpf_object__unpin() API function to libbpf,
from Daniel Xu.
13) Fix a memory leak in libbpf to also free btf_vmlinux
when the bpf_object gets closed, from Hao Luo.
14) Small error output improvements to test_bpf module, from Helge Deller.
* tag 'for-netdev' of https://git.kernel.org/pub/scm/linux/kernel/git/bpf/bpf-next: (87 commits)
selftests/bpf: Add tests for rbtree API interaction in sleepable progs
bpf: Allow bpf_spin_{lock,unlock} in sleepable progs
bpf: Consider non-owning refs to refcounted nodes RCU protected
bpf: Reenable bpf_refcount_acquire
bpf: Use bpf_mem_free_rcu when bpf_obj_dropping refcounted nodes
bpf: Consider non-owning refs trusted
bpf: Ensure kptr_struct_meta is non-NULL for collection insert and refcount_acquire
selftests/bpf: Enable cpu v4 tests for RV64
riscv, bpf: Support unconditional bswap insn
riscv, bpf: Support signed div/mod insns
riscv, bpf: Support 32-bit offset jmp insn
riscv, bpf: Support sign-extension mov insns
riscv, bpf: Support sign-extension load insns
riscv, bpf: Fix missing exception handling and redundant zext for LDX_B/H/W
samples/bpf: Add note to README about the XDP utilities moved to xdp-tools
samples/bpf: Cleanup .gitignore
samples/bpf: Remove the xdp_sample_pkts utility
samples/bpf: Remove the xdp1 and xdp2 utilities
samples/bpf: Remove the xdp_rxq_info utility
samples/bpf: Remove the xdp_redirect* utilities
...
====================
Link: https://lore.kernel.org/r/20230825194319.12727-1-daniel@iogearbox.net
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
