Currently, the R-Car GPIO driver treats R-Car Gen2 and R-Car Gen3 GPIO
controllers the same. However, there exist small differences, like the
behavior of the General Input Register (INDT):
- On R-Car Gen1, R-Car Gen2, and RZ/G1, INDT only reflects the state
of an input pin if the GPIO is configured for input,
- On R-Car Gen3 and RZ/G2, INDT always reflects the state of the input
pins.
Hence to accommodate all variants, the driver does not use the INDT
register to read the status of a GPIO line when configured for output,
at the expense of doing 2 or 3 register reads instead of 1.
Given register accesses are slow, change the .get() and .get_multiple()
callbacks to always use INDT to read pin state on SoCs where this is
supported.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Tested-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Document the compatible value for the GPIO block in the Renesas R-Car
V3U (R8A779A0) SoC.
While this GPIO block is mostly compatible with GPIO blocks on R-Car
Gen3 SoCs, there are small differences, and one of the new registers
needs to be configured differently from its initial reset state.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Using a helper local variable to store the address of &pdev->dev adds
to readability and allows us to avoid unnecessary line breaks.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Reviewed-by: Matti Vaittinen <matti.vaittinen@fi.rohmeurope.com>
Convert the Tegra GPIO driver to use the gpio_irq_chip infrastructure.
This allows a bit of boiler plate to be removed and while at it enables
support for hierarchical domains, which is useful to support PMC wake
events on Tegra210 and earlier.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Add compatible string for AM64 SoC in device tree binding of davinci GPIO
modules as the same IP is used.
Signed-off-by: Aswath Govindraju <a-govindraju@ti.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
The ROHM BD70528 and BD71828 GPIO drivers only need the regmap
pointer from parent. Regmap can be obtained via dev_get_regmap()
so do not require parent to populate driver data for that.
Signed-off-by: Matti Vaittinen <matti.vaittinen@fi.rohmeurope.com>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
The mandatory compatible values 'renesas,rcar-gen{1,2,3}-gpio' have been
already added to all the respective R-Car Gen{1,2,3} SoC DTSI files,
remove the redundant device specific values from the driver.
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Currently the HTML output for Documentation/driver-api/gpio/intro.rst
doesn't look right. The lines that start with LOW or HIGH are formatted
in bold, while the next line after each is not bold.
With this patch, the HTML looks better.
Signed-off-by: Jonathan Neuschäfer <j.neuschaefer@gmx.net>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
The gpiod_*_array_* functions take four arguments, not three.
Additionally, the formatting of the "value_bitmap" line results in
misformatted HTML, so fix that.
Signed-off-by: Jonathan Neuschäfer <j.neuschaefer@gmx.net>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Pull LED fix from Pavel Machek:
"One-liner fixing a build problem"
* 'for-rc8-5.11' of git://git.kernel.org/pub/scm/linux/kernel/git/pavel/linux-leds:
leds: rt8515: add V4L2_FLASH_LED_CLASS dependency
Pull Kbuild fixes from Masahiro Yamada:
- Fix CONFIG_TRIM_UNUSED_KSYMS build for ppc64
- Use pkg-config for scripts/sign-file.c CFLAGS
* tag 'kbuild-fixes-v5.11-3' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild:
scripts: set proper OpenSSL include dir also for sign-file
sparc: remove wrong comment from arch/sparc/include/asm/Kbuild
kbuild: fix CONFIG_TRIM_UNUSED_KSYMS build for ppc64
Pull x86 fixes from Borislav Petkov:
"I kinda knew while typing 'I hope this is the last batch of x86/urgent
updates' last week, Murphy was reading too and uttered 'Hold my
beer!'.
So here's more fixes... Thanks Murphy.
Anyway, three more x86/urgent fixes for 5.11 final. We should be
finally ready (famous last words). :-)
- An SGX use after free fix
- A fix for the fix to disable CET instrumentation generation for
kernel code. We forgot 32-bit, which we seem to do very often
nowadays
- A Xen PV fix to irqdomain init ordering"
* tag 'x86_urgent_for_v5.11' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/pci: Create PCI/MSI irqdomain after x86_init.pci.arch_init()
x86/build: Disable CET instrumentation in the kernel for 32-bit too
x86/sgx: Maintain encl->refcount for each encl->mm_list entry
The leds-rt8515 driver can optionall use the v4l2 flash led class,
but it causes a link error when that class is in a loadable module
and the rt8515 driver itself is built-in:
ld.lld: error: undefined symbol: v4l2_flash_init
>>> referenced by leds-rt8515.c
>>> leds/flash/leds-rt8515.o:(rt8515_probe) in archive
drivers/built-in.a
Adding 'depends on V4L2_FLASH_LED_CLASS' in Kconfig would avoid that,
but it would make it impossible to use the driver without the
v4l2 support.
Add the same dependency that the other users of this class have
instead, which just prevents the broken configuration.
Fixes: e1c6edcbea ("leds: rt8515: Add Richtek RT8515 LED driver")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Pavel Machek <pavel@ucw.cz>
These are NOT exported to userspace.
The headers listed in arch/sparc/include/uapi/asm/Kbuild are exported.
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
Pull clk fix from Stephen Boyd:
"One small fix for the Allwinner clk driver so that display clks figure
out the correct rate to use.
This fixes displays running 4k@60Hz and some other resolutions that
haven't been exercised and fully understood until now"
* tag 'clk-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux:
clk: sunxi-ng: mp: fix parent rate change flag check
Pull SCSI fix from James Bottomley:
"One fix for scsi_debug that fixes a memory leak on module removal"
* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
scsi: scsi_debug: Fix a memory leak
Pull cgroup fixes from Tejun Heo:
"Two cgroup fixes:
- fix a NULL deref when trying to poll PSI in the root cgroup
- fix confusing controller parsing corner case when mounting cgroup
v1 hierarchies
And doc / maintainer file updates"
* 'for-5.11-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/cgroup:
cgroup: update PSI file description in docs
cgroup: fix psi monitor for root cgroup
MAINTAINERS: Update my email address
MAINTAINERS: Remove stale URLs for cpuset
cgroup-v1: add disabled controller check in cgroup1_parse_param()
Merge fixes from Andrew Morton:
"6 patches.
Subsystems affected by this patch series: mm/pagemap, scripts,
MAINTAINERS, and h8300"
* emailed patches from Andrew Morton <akpm@linux-foundation.org>:
h8300: fix PREEMPTION build, TI_PRE_COUNT undefined
MAINTAINERS: add Andrey Konovalov to KASAN reviewers
MAINTAINERS: update Andrey Konovalov's email address
MAINTAINERS: update KASAN file list
scripts/recordmcount.pl: support big endian for ARCH sh
m68k: make __pfn_to_phys() and __phys_to_pfn() available for !MMU
Pull i2c fix from Wolfram Sang:
"One more I2C driver bugfix"
* 'i2c/for-current' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux:
i2c: stm32f7: fix configuration of the digital filter
Pull btrfs fix from David Sterba:
"A regression fix caused by a refactoring in 5.11.
A corrupted superblock wouldn't be detected by checksum verification
due to wrongly placed initialization of the checksum length, thus
making memcmp always work"
* tag 'for-5.11-rc7-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/kdave/linux:
btrfs: initialize fs_info::csum_size earlier in open_ctree
The kernel test robot reported the following issue:
CC [M] drivers/soc/litex/litex_soc_ctrl.o
sh4-linux-objcopy: Unable to change endianness of input file(s)
sh4-linux-ld: cannot find drivers/soc/litex/.tmp_gl_litex_soc_ctrl.o: No such file or directory
sh4-linux-objcopy: 'drivers/soc/litex/.tmp_mx_litex_soc_ctrl.o': No such file
The problem is that the format of input file is elf32-shbig-linux, but
sh4-linux-objcopy wants to output a file which format is elf32-sh-linux:
$ sh4-linux-objdump -d drivers/soc/litex/litex_soc_ctrl.o | grep format
drivers/soc/litex/litex_soc_ctrl.o: file format elf32-shbig-linux
Link: https://lkml.kernel.org/r/20210210150435.2171567-1-rong.a.chen@intel.com
Link: https://lore.kernel.org/linux-mm/202101261118.GbbYSlHu-lkp@intel.com
Signed-off-by: Rong Chen <rong.a.chen@intel.com>
Reported-by: kernel test robot <lkp@intel.com>
Cc: Yoshinori Sato <ysato@users.osdn.me>
Cc: Rich Felker <dalias@libc.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Recent changes that obsoleted DISCONTIGMEM on m68k switched the MMU
variant to use generic definitions of __pfn_to_phys() and __phys_to_pfn(),
but missed the !MMU variant which caused a build failure:
drivers/media/common/videobuf2/videobuf2-dma-contig.c: In function 'vb2_dc_get_userptr':
drivers/media/common/videobuf2/videobuf2-dma-contig.c:509:5: error: implicit declaration of function '__pfn_to_phys' [-Werror=implicit-function-declaration]
509 | __pfn_to_phys(nums[0]), size, buf->dma_dir, 0);
| ^~~~~~~~~~~~~
cc1: some warnings being treated as errors
Enable __pfn_to_phys() and __phys_to_pfn() on !MMU builds.
Link: https://lkml.kernel.org/r/20210211232202.GS299309@linux.ibm.com
Fixes: 4bfc848e09 ("m68k/mm: enable use of generic memory_model.h for !DISCONTIGMEM")
Signed-off-by: Mike Rapoport <rppt@linux.ibm.com>
Reported-by: kernel test robot <lkp@intel.com>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Greg Ungerer <gerg@linux-m68k.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Pull cifs fixes from Steve French:
"Four small smb3 fixes to the new mount API (including a particularly
important one for DFS links).
These were found in testing this week of additional DFS scenarios, and
a user testing of an apache container problem"
* tag '5.11-rc7-smb3-github' of git://github.com/smfrench/smb3-kernel:
cifs: Set CIFS_MOUNT_USE_PREFIX_PATH flag on setting cifs_sb->prepath.
cifs: In the new mount api we get the full devname as source=
cifs: do not disable noperm if multiuser mount option is not provided
cifs: fix dfs-links
Pull io_uring fix from Jens Axboe:
"Revert of a patch from this release that caused a regression"
* tag 'io_uring-5.11-2021-02-12' of git://git.kernel.dk/linux-block:
Revert "io_uring: don't take fs for recvmsg/sendmsg"
Pull drm fixes from Dave Airlie:
"Regular fixes for final, there is a ttm regression fix, dp-mst fix,
one amdgpu revert, two i915 fixes, and some misc fixes for sun4i,
xlnx, and vc4.
All pretty quiet and don't think we have any known outstanding
regressions.
ttm:
- page pool regression fix.
dp_mst:
- don't report un-attached ports as connected
amdgpu:
- blank screen fix
i915:
- ensure Type-C FIA is powered when initializing
- fix overlay frontbuffer tracking
sun4i:
- tcon1 sync polarity fix
- always set HDMI clock rate
- fix H6 HDMI PHY config
- fix H6 max frequency
vc4:
- fix buffer overflow
xlnx:
- fix memory leak"
* tag 'drm-fixes-2021-02-12' of git://anongit.freedesktop.org/drm/drm:
drm/ttm: make sure pool pages are cleared
drm/sun4i: dw-hdmi: Fix max. frequency for H6
drm/sun4i: Fix H6 HDMI PHY configuration
drm/sun4i: dw-hdmi: always set clock rate
drm/sun4i: tcon: set sync polarity for tcon1 channel
drm/i915: Fix overlay frontbuffer tracking
Revert "drm/amd/display: Update NV1x SR latency values"
drm/i915/tgl+: Make sure TypeC FIA is powered up when initializing it
drm/dp_mst: Don't report ports connected if nothing is attached to them
drm/xlnx: fix kmemleak by sending vblank_event in atomic_disable
drm/vc4: hvs: Fix buffer overflow with the dlist handling
Pull tracing fix from Steven Rostedt:
"Fix buffer overflow in trace event filter.
It was reported that if an trace event was larger than a page and was
filtered, that it caused memory corruption. The reason is that
filtered events first go into a buffer to test the filter before being
written into the ring buffer. Unfortunately, this write did not check
the size"
* tag 'trace-v5.11-rc7-2' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace:
tracing: Check length before giving out the filter buffer
Pull xen fix from Juergen Gross:
"A single fix for an issue introduced this development cycle: when
running as a Xen guest on Arm systems the kernel will hang during
boot"
* tag 'for-linus-5.11-rc8-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip:
arm/xen: Don't probe xenbus as part of an early initcall
Pull RISC-V fix from Palmer Dabbelt:
"A single fix this week: the removal of the GPIO reset method for the
Ethernet phy on the HiFive Unleashed.
This returns to relying on the bootloader's phy reset sequence, which
we'll have to continue doing until we can sort out how to get the
Linux phy driver to perform the special reset dance required for this
phy"
* tag 'riscv-for-linus-5.11-rc8' of git://git.kernel.org/pub/scm/linux/kernel/git/riscv/linux:
Revert "dts: phy: add GPIO number and active state used for phy reset"
Pull arm64 fix from Catalin Marinas:
"Fix PTRACE_PEEKMTETAGS access to an mmapped region before the first
write"
* tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux:
arm64: mte: Allow PTRACE_PEEKMTETAGS access to the zero page
The ptrace(PTRACE_PEEKMTETAGS) implementation checks whether the user
page has valid tags (mapped with PROT_MTE) by testing the PG_mte_tagged
page flag. If this bit is cleared, ptrace(PTRACE_PEEKMTETAGS) returns
-EIO.
A newly created (PROT_MTE) mapping points to the zero page which had its
tags zeroed during cpu_enable_mte(). If there were no prior writes to
this mapping, ptrace(PTRACE_PEEKMTETAGS) fails with -EIO since the zero
page does not have the PG_mte_tagged flag set.
Set PG_mte_tagged on the zero page when its tags are cleared during
boot. In addition, to avoid ptrace(PTRACE_PEEKMTETAGS) succeeding on
!PROT_MTE mappings pointing to the zero page, change the
__access_remote_tags() check to (vm_flags & VM_MTE) instead of
PG_mte_tagged.
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Fixes: 34bfeea4a9 ("arm64: mte: Clear the tags when a page is mapped in user-space with PROT_MTE")
Cc: <stable@vger.kernel.org> # 5.10.x
Cc: Will Deacon <will@kernel.org>
Reported-by: Luis Machado <luis.machado@linaro.org>
Tested-by: Luis Machado <luis.machado@linaro.org>
Reviewed-by: Vincenzo Frascino <vincenzo.frascino@arm.com>
Link: https://lore.kernel.org/r/20210210180316.23654-1-catalin.marinas@arm.com
User reported that btrfs-progs misc-tests/028-superblock-recover fails:
[TEST/misc] 028-superblock-recover
unexpected success: mounted fs with corrupted superblock
test failed for case 028-superblock-recover
The test case expects that a broken image with bad superblock will be
rejected to be mounted. However, the test image just passed csum check
of superblock and was successfully mounted.
Commit 55fc29bed8 ("btrfs: use cached value of fs_info::csum_size
everywhere") replaces all calls to btrfs_super_csum_size by
fs_info::csum_size. The calls include the place where fs_info->csum_size
is not initialized. So btrfs_check_super_csum() passes because memcmp()
with len 0 always returns 0.
Fix it by caching csum size in btrfs_fs_info::csum_size once we know the
csum type in superblock is valid in open_ctree().
Link: https://github.com/kdave/btrfs-progs/issues/250
Fixes: 55fc29bed8 ("btrfs: use cached value of fs_info::csum_size everywhere")
Signed-off-by: Su Yue <l@damenly.su>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
The digital filter related computation are present in the driver
however the programming of the filter within the IP is missing.
The maximum value for the DNF is wrong and should be 15 instead of 16.
Fixes: aeb068c572 ("i2c: i2c-stm32f7: add driver")
Signed-off-by: Alain Volmat <alain.volmat@foss.st.com>
Signed-off-by: Pierre-Yves MORDRET <pierre-yves.mordret@foss.st.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Pull powerpc fix from Michael Ellerman:
"One fix for a regression seen in io_uring, introduced by our support
for KUAP (Kernel User Access Prevention) with the Hash MMU.
Thanks to Aneesh Kumar K.V, and Zorro Lang"
* tag 'powerpc-5.11-8' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux:
powerpc/kuap: Allow kernel thread to access userspace after kthread_use_mm
