xhci DbC driver polls the host controller for DbC events at a reduced
rate when DbC is enabled but there are no active data transfers.
Allow users to modify this reduced poll interval via dbc_poll_interval_ms
sysfs entry. Unit is milliseconds and accepted range is 0 to 5000.
Max interval of 5000 ms is selected as it matches the common 5 second
timeout used in usb stack.
Default value is 64 milliseconds.
A long interval is useful when users know there won't be any activity
on systems connected via DbC for long periods, and want to avoid
battery drainage due to unnecessary CPU usage.
Example being Android Debugger (ADB) usage over DbC on ChromeOS systems
running Android Runtime.
[minor changes and rewording -Mathias]
Co-developed-by: Samuel Jacob <samjaco@google.com>
Signed-off-by: Samuel Jacob <samjaco@google.com>
Signed-off-by: Uday M Bhat <uday.m.bhat@intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20240626124835.1023046-5-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The transferred length is incorrectly zeroed for cancelled isoc
transfer TDs when the transfer ring stops on a cancelled TD with
a 'Stop - Length Invalid' completion code.
Length was always set to zero in these cases even if it should be
set to the sum of the TRB transfer block lengths up to
the TRB the ring stopped on, _excluding_ the one stopped on.
No issues reported due to this isoc case. Found while inspecting
related case in bulk transfer 'Stop - Length Invalid' handling.
Change this so that 'Stop - Length Invalid' transfer completion
cases always sum up TRB lengths instead of report a zero length.
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20240626124835.1023046-4-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
parsing xhci traces on systems with several xHCI controllers and connected
usb devices is difficult as entries are all interleaved.
showing usb devname in urb tracing reveals both which device, and which
bus/controller the entry is for.
old:
xhci_urb_enqueue: ep2in-bulk: urb 0000000039224498 ...
new:
xhci_urb_enqueue: 3-9.4 ep1in-bulk: urb 0000000013bf21e7 ...
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20240626124835.1023046-3-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Replace SET_RUNTIME_PM_OPS() with its modern RUNTIME_PM_OPS()
alternative.
The combined usage of pm_ptr() and RUNTIME_PM_OPS allows the compiler
to evaluate if the runtime suspend/resume() functions are used at build
time or are simply dead code.
This allows removing the __maybe_unused notation from the runtime
suspend/resume() functions.
Signed-off-by: Fabio Estevam <festevam@denx.de>
Link: https://lore.kernel.org/r/20240625231023.436403-2-festevam@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Replace SET_RUNTIME_PM_OPS()/SET SYSTEM_SLEEP_PM_OPS() with their modern
RUNTIME_PM_OPS() and SYSTEM_SLEEP_PM_OPS() alternatives.
The combined usage of pm_ptr() and RUNTIME_PM_OPS/SYSTEM_SLEEP_PM_OPS()
allows the compiler to evaluate if the runtime suspend/resume() functions
are used at build time or are simply dead code.
This allows removing the __maybe_unused notation from the runtime
suspend/resume() functions.
Signed-off-by: Fabio Estevam <festevam@denx.de>
Link: https://lore.kernel.org/r/20240625231023.436403-1-festevam@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add a match function for the onboard_usb_dev driver. Primary
matching is still done through the VID:PID pair, as usual for
USB devices. The new match function checks in addition whether
the device has a device tree node, which is a needed for using
the onboard_usb_dev driver.
Remove the check for a device tree node from _probe(), the new
match functions prevents devices without DT node from probing.
Signed-off-by: Matthias Kaehlcke <mka@chromium.org>
Tested-by: Jameson Thies <jthies@google.com>
Reviewed-by: Jameson Thies <jthies@google.com>
Link: https://lore.kernel.org/r/20240612180448.1.I805556c176c626872c15ce001f0e8198e1f95ae1@changeid
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Set the host status byte when a data completion error is encountered
otherwise the upper layer may end up using the invalid zero'ed data.
The following output was observed from scsi/sd.c prior to this fix.
[ 11.872824] sd 0:0:0:1: [sdf] tag#9 data cmplt err -75 uas-tag 1 inflight:
[ 11.872826] sd 0:0:0:1: [sdf] tag#9 CDB: Read capacity(16) 9e 10 00 00 00 00 00 00 00 00 00 00 00 20 00 00
[ 11.872830] sd 0:0:0:1: [sdf] Sector size 0 reported, assuming 512.
Signed-off-by: Shantanu Goel <sgoel01@yahoo.com>
Acked-by: Oliver Neukum <oneukum@suse.com>
Link: https://lore.kernel.org/r/87msnx4ec6.fsf@yahoo.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Mika writes:
thunderbolt: Changes for v6.11 merge window
This includes following USB4/Thunderbolt changes for the v6.11 merge
window:
- Add receiver lane margining support for retimers
- Add sideband register access to debugfs
- Minor cleanups.
All these have been in linux-next with no reported issues.
* tag 'thunderbolt-for-v6.11-rc1' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/westeri/thunderbolt:
thunderbolt: debugfs: Use FIELD_GET()
thunderbolt: Add receiver lane margining support for retimers
thunderbolt: Make margining functions accept target and retimer index
thunderbolt: Split out margining from USB4 port
thunderbolt: Add sideband register access to debugfs
thunderbolt: Make usb4_port_sb_read/write() available outside of usb4.c
thunderbolt: Move usb4_port_margining_caps() declaration into correct place
thunderbolt: Mention Thunderbolt/USB4 debugging tools in Kconfig
Introduce a new 'of-fullname-regex' property that takes a regular
expression and matches against the OF_FULLNAME property. It allows
matching controllers that don't have a unique DT address across sibling
controllers, and thus dt-mmio can't be used.
One particular example of where this is needed is on MT8195 which has
multiple USB controllers described by two level deep nodes and using the
ranges property:
ssusb2: usb@112a1000 {
reg = <0 0x112a1000 0 0x2dff>, <0 0x112a3e00 0 0x0100>;
ranges = <0 0 0 0x112a0000 0 0x3f00>;
xhci2: usb@0 {
Signed-off-by: Nícolas F. R. A. Prado <nfraprado@collabora.com>
Link: https://lore.kernel.org/r/20240613-kselftest-discoverable-probe-mt8195-kci-v1-2-7b396a9b032d@collabora.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add the binding example for the USB3.1 Genesys Logic GL3523
integrates with USB 3.1 Gen 1 Super Speed and USB 2.0 High-Speed
hub.
For onboard hub controllers that support USB 3.x and USB 2.0 hubs
with shared resets and power supplies, this property is used to identify
the hubs with which these are shared.
GL3523 has built-in 5V to 3.3V and 5V to 1.2V regulators, which serves
power to the USB HUB, it uses 5V power regulator.
Update the peer-hub description.
Reviewed-by: Conor Dooley <conor.dooley@microchip.com>
Signed-off-by: Anand Moon <linux.amoon@gmail.com>
Link: https://lore.kernel.org/r/20240613123020.43500-1-linux.amoon@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
On systems where the UCSI PDOs are not supported, the UCSI driver is
giving an error message. This can cause users to believe there is a HW
issue with their system when in fact it is working as designed.
Check if PDO_DETAILS are supported as a feature before attempting to
access PDO. If not supported return that zero PDOs are available.
Tested on Lenovo L14 G5 AMD and confirmed with Lenovo FW team that PDOs
are not supported on this platform.
Suggested-by: Diogo Ivo <diogo.ivo@siemens.com>
Suggested-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Mark Pearson <mpearson-lenovo@squebb.ca>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20240609214328.6580-1-mpearson-lenovo@squebb.ca
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This quirk is for the controller that has a limitation in supporting
separate ERSTBA_HI and ERSTBA_LO programming. It's supported when
the ERSTBA is programmed ERSTBA_HI before ERSTBA_LO. That's because
the internal initialization of event ring fetches the
"Event Ring Segment Table Entry" based on the indication of ERSTBA_LO
written.
Signed-off-by: Daehwan Jung <dh10.jung@samsung.com>
Link: https://lore.kernel.org/r/1718019553-111939-3-git-send-email-dh10.jung@samsung.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There's the limitation of Synopsys dwc3 controller with ERST programming in
supporting separate ERSTBA_HI and ERSTBA_LO programming. It's supported when
the ERSTBA is programmed ERSTBA_HI before ERSTBA_LO. But, writing operations
in xHCI is done low-high order following xHCI spec. xHCI specification 5.1
"Register Conventions" states that 64 bit registers should be written in
low-high order. Synopsys dwc3 needs workaround for high-low order. That's why
adding new quirk is needed to support this.
Signed-off-by: Daehwan Jung <dh10.jung@samsung.com>
Link: https://lore.kernel.org/r/1718019553-111939-2-git-send-email-dh10.jung@samsung.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
With ARCH=x86, make allmodconfig && make W=1 C=1 reports:
WARNING: modpost: missing MODULE_DESCRIPTION() in drivers/usb/core/usbcore.o
WARNING: modpost: missing MODULE_DESCRIPTION() in drivers/usb/mon/usbmon.o
WARNING: modpost: missing MODULE_DESCRIPTION() in drivers/usb/class/usbtmc.o
WARNING: modpost: missing MODULE_DESCRIPTION() in drivers/usb/storage/uas.o
WARNING: modpost: missing MODULE_DESCRIPTION() in drivers/usb/chipidea/ci_hdrc_msm.o
Add the missing invocations of the MODULE_DESCRIPTION() macro.
Signed-off-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Link: https://lore.kernel.org/r/20240618-md-drivers-usb-v2-1-e9b20a5eb7f9@quicinc.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
With ARCH=x86, make allmodconfig && make W=1 C=1 reports:
WARNING: modpost: missing MODULE_DESCRIPTION() in drivers/usb/misc/ezusb.o
WARNING: modpost: missing MODULE_DESCRIPTION() in drivers/usb/misc/isight_firmware.o
WARNING: modpost: missing MODULE_DESCRIPTION() in drivers/usb/misc/yurex.o
Add the missing invocations of the MODULE_DESCRIPTION() macro.
Signed-off-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Link: https://lore.kernel.org/r/20240611-md-drivers-usb-misc-v1-1-98475a5aa8ef@quicinc.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use common usb-drd yaml for usb OTG related propteries to fix below
DTB_CHECK warning.
arch/arm64/boot/dts/freescale/imx8qxp-mek.dtb: usb@5b110000: usb@5b120000: 'port', 'usb-role-switch' do not match any of the regexes: 'pinctrl-[0-9]+'
Add "port" proptery to use connect type C connector and fix below warning.
arch/arm64/boot/dts/freescale/imx8qxp-mek.dtb: usb@5b110000: usb@5b120000: Unevaluated properties are not allowed ('port' was unexpected)
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Reviewed-by: Rob Herring (Arm) <robh@kernel.org>
Link: https://lore.kernel.org/r/20240607154119.1543290-1-Frank.Li@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Retimers support lane margining as well so make this available through
debugfs in the same way as we do for the USB4 ports. When this is
enabled we also expose retimers on the other side of the cable because
typically margining is implemented only on direction towards the cable.
However, for the retimers on the other side of the cable we do not allow
NVM upgrade to avoid confusing the existing userspace (the same retimer
may now appear twice with different name) and is probably not a good
idea anyway.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
In order to add lane margining support for retimers make the margining
functions take sideband target and retimer index as parameters. This
makes it possible to access both router and retimer sideband using the
same functions.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
We are going to expand lane margining support for retimers too so split
out the generic margining functionality out of being specific to USB4
ports.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
This makes it possible to read and write USB4 port and retimer sideband
registers through debugfs which is useful for debugging and manufacturing
purposes. We add "sb_regs" debugfs attribute under each USB4 port and
retimer that is used to access the sideband.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
It is supposed to be close with the other lane margining functions so
move it there. No functional changes.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
