The reset deassert time for the DP83TD510E is incorrectly set to
60000us, while the datasheet states that the minimum time required
after an hard reset is 30us (while 60ms is the time required for the
Power-On Reset after supply stabilization). The error probably arose
from the two timings being indicated by the same symbol (T2).
Lower the required time to 35us, aligning it to the value required for
the PHY to complete the reset AND to be able to accept the RMII master
clock. This saves ~60ms on boot if the MDIO driver is built-in.
Signed-off-by: Francesco Valla <francesco@valla.it>
Link: https://lore.kernel.org/r/20250105162630.243899-1-francesco@valla.it
Signed-off-by: Nishanth Menon <nm@ti.com>
SolidRun HummingBoard-T has two options for M.2 connector, supporting
either PCI-E or USB-3.1 Gen 1 - depending on configuration of a mux
on the serdes lane.
The required configurations in device-tree were modeled as overlays.
The USB-3.1 overlay uses /delete-property/ to unset a boolean property
on the usb controller limiting it to USB-2.0 by default.
Overlays can not delete a property from the base dtb, therefore this
overlay is at this time useless.
Convert both overlays into full dts by including the base board dts.
While the pcie overlay was functional, both are converted for a
consistent user experience when selecting between the two mutually
exclusive configurations.
Reported-by: Geert Uytterhoeven <geert@linux-m68k.org>
Closes: https://lore.kernel.org/linux-devicetree/CAMuHMdXTgpTnJ9U7egC2XjFXXNZ5uiY1O+WxNd6LPJW5Rs5KTw@mail.gmail.com
Fixes: bbef42084c ("arm64: dts: ti: hummingboard-t: add overlays for m.2 pci-e and usb-3")
Signed-off-by: Josua Mayer <josua@solid-run.com>
Link: https://lore.kernel.org/r/20250101-am64-hb-fix-overlay-v2-1-78143f5da28c@solid-run.com
Signed-off-by: Nishanth Menon <nm@ti.com>
Add overlay to enable the PCIE1 instance of PCIe on AM68-SK-Base-Board in
Endpoint mode of operation. PCIE1 on AM68-SK-Base-Board supports x2 Lane
operation unlike its counterpart on J721S2-EVM which supports x1 Lane.
Signed-off-by: Siddharth Vadapalli <s-vadapalli@ti.com>
Link: https://lore.kernel.org/r/20241205105041.749576-4-s-vadapalli@ti.com
Signed-off-by: Nishanth Menon <nm@ti.com>
Add overlay to enable the PCIE1 instance of PCIe on J721E-EVM in Endpoint
mode of operation. Additionally, in order to support both PCIE0 and PCIE1
in Endpoint Mode of operation, enable applying device-tree overlays on
"k3-j721e-evm-pcie0-ep.dtb", thereby allowing the overlay for PCIE1 in
Endpoint mode to be applied on the aforementioned DTB.
Signed-off-by: Siddharth Vadapalli <s-vadapalli@ti.com>
Link: https://lore.kernel.org/r/20241205105041.749576-3-s-vadapalli@ti.com
Signed-off-by: Nishanth Menon <nm@ti.com>
The list of "dtbs" should contain the resultant "dtb" formed by applying
the "dtbo" overlay on the base "dtb", rather than the "dtbo" itself.
Hence, change "k3-j7200-evm-pcie1-ep.dtbo" to "k3-j7200-evm-pcie1-ep.dtb"
in the list of "dtbs".
Fixes: f43ec89bbc ("arm64: dts: ti: k3-j7200-evm: Add overlay for PCIE1 Endpoint Mode")
Signed-off-by: Siddharth Vadapalli <s-vadapalli@ti.com>
Link: https://lore.kernel.org/r/20241205105041.749576-2-s-vadapalli@ti.com
Signed-off-by: Nishanth Menon <nm@ti.com>
CTRLMMR_MCU_SPI1_CTRL register controls if MCU_SPI1 is directly
connected to SPI3 in the MAIN Domain (default) or if MCU_SPI1
and SPI3 are independently pinned out. By default, the field
SPI1_LINKDIS (Bit 0) is set to 0h. In order to disable the direct
connection, the SPI1_LINKDIS (Bit 0) needs to be set to 1h. Model
this functionality as a "reg-mux" device and based on the idle-state
property, enable/disable the connection bewtween MCU_SPI1 and MAIN_SPI3.
The register field description has been referred from J7200 TRM [1]
(Table 5-517. CTRLMMR_MCU_SPI1_CTRL Register Field Descriptions).
[1] https://www.ti.com/lit/pdf/spruiu1
Signed-off-by: Anurag Dutta <a-dutta@ti.com>
Link: https://lore.kernel.org/r/20241127075644.210759-1-a-dutta@ti.com
Signed-off-by: Nishanth Menon <nm@ti.com>
Mailbox nodes defined in the top-level J722s/AM62p SoC dtsi files are
incomplete and may not be functional unless they are extended with a
chosen interrupt and connection to a remote processor.
Disable the Mailbox nodes in the dtsi files and only enable the ones
that are actually used on a given board.
Signed-off-by: Andrew Davis <afd@ti.com>
Link: https://lore.kernel.org/r/20241203174114.94751-1-afd@ti.com
Signed-off-by: Nishanth Menon <nm@ti.com>
Ethernet boot requires CPSW node to be present starting from R5 SPL stage.
Add bootph-all property in CPSW MAC's eFuse node cpsw_mac_syscon to enable
this node during SPL stage along with later boot stages so that CPSW port
will get static MAC address.
Reviewed-by: Siddharth Vadapalli <s-vadapalli@ti.com>
Signed-off-by: Chintan Vankar <c-vankar@ti.com>
Link: https://lore.kernel.org/r/20241114165331.1279065-1-c-vankar@ti.com
Signed-off-by: Nishanth Menon <nm@ti.com>
Remove "ti,(rx|tx)-fifo-depth" properties which are both unused in the
kernel and undocumented. Most likely they are leftovers from downstream.
There are similar properties, but DP83867_PHYCR_FIFO_DEPTH_4_B_NIB
represents the default value so adding them is not necessary.
Signed-off-by: Rob Herring (Arm) <robh@kernel.org>
Link: https://lore.kernel.org/r/20241115193359.3618020-1-robh@kernel.org
Signed-off-by: Nishanth Menon <nm@ti.com>
ICSSG has 7 available clocks per instance. Add all the cloks to ICSSG
nodes. ICSSG currently uses ICSSG_ICLK (clk id 20) which operates at
250MHz. Switch ICSSG clock to ICSSG_CORE clock (clk id 0) which operates at
333MHz.
ICSSG_CORE clock will help get the most out of ICSSG as more cycles are
needed to fully support all ICSSG features.
This commit also changes assigned-clock-parents of coreclk-mux to
ICSSG_CORE clock from ICSSG_ICLK.
Performance update in dual mac mode
With ICSSG_CORE Clk @ 333MHz
Tx throughput - 934 Mbps
Rx throughput - 914 Mbps,
With ICSSG_ICLK clk @ 250MHz,
Tx throughput - 920 Mbps
Rx throughput - 706 Mbps
Signed-off-by: MD Danish Anwar <danishanwar@ti.com>
Tested-by: Wadim Egorov <w.egorov@phytec.de>
Reviewed-by: Roger Quadros <rogerq@kernel.org>
Link: https://lore.kernel.org/r/20241113110955.3876045-3-danishanwar@ti.com
Signed-off-by: Nishanth Menon <nm@ti.com>
After the SoC has entered the Deep Sleep mode, USB1 can be used to wakeup
the SoC based on USB events triggered by USB devices. This requires that
the pin corresponding to the Type-A connector remains pulled up even after
the SoC has entered the Deep Sleep mode. Hence, enable Deep Sleep pullup /
pulldown selection for the USB1_DRVVBUS pin and set its Deep Sleep state to
PULL_UP.
Signed-off-by: Siddharth Vadapalli <s-vadapalli@ti.com>
Link: https://lore.kernel.org/r/20241205120134.754664-3-s-vadapalli@ti.com
Signed-off-by: Nishanth Menon <nm@ti.com>
Specify I/0 voltage & core supply regulators used by the SII902x
HDMI bridge and make them known to the bridge.
This resolves the following warning:
sii902x 1-0039: supply iovcc not found, using dummy regulator
sii902x 1-0039: supply cvcc12 not found, using dummy regulator
Signed-off-by: Wadim Egorov <w.egorov@phytec.de>
Link: https://lore.kernel.org/r/20241101131427.3815341-2-w.egorov@phytec.de
Signed-off-by: Nishanth Menon <nm@ti.com>
Pull i2c component probing support from Wolfram Sang:
"Add OF component probing.
Some devices are designed and manufactured with some components having
multiple drop-in replacement options. These components are often
connected to the mainboard via ribbon cables, having the same signals
and pin assignments across all options. These may include the display
panel and touchscreen on laptops and tablets, and the trackpad on
laptops. Sometimes which component option is used in a particular
device can be detected by some firmware provided identifier, other
times that information is not available, and the kernel has to try to
probe each device.
Instead of a delicate dance between drivers and device tree quirks,
this change introduces a simple I2C component probe function. For a
given class of devices on the same I2C bus, it will go through all of
them, doing a simple I2C read transfer and see which one of them
responds. It will then enable the device that responds"
* tag 'i2c-for-6.13-rc1-part3' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux:
MAINTAINERS: fix typo in I2C OF COMPONENT PROBER
of: base: Document prefix argument for of_get_next_child_with_prefix()
i2c: Fix whitespace style issue
arm64: dts: mediatek: mt8173-elm-hana: Mark touchscreens and trackpads as fail
platform/chrome: Introduce device tree hardware prober
i2c: of-prober: Add GPIO support to simple helpers
i2c: of-prober: Add simple helpers for regulator support
i2c: Introduce OF component probe function
of: base: Add for_each_child_of_node_with_prefix()
of: dynamic: Add of_changeset_update_prop_string
Pull bprintf() removal from Steven Rostedt:
- Remove unused bprintf() function, that was added with the rest of the
"bin-printf" functions.
These are functions that are used by trace_printk() that allows to
quickly save the format and arguments into the ring buffer without
the expensive processing of converting numbers to ASCII. Then on
output, at a much later time, the ring buffer is read and the string
processing occurs then. The bprintf() was added for consistency but
was never used. It can be safely removed.
* tag 'trace-printf-v6.13' of git://git.kernel.org/pub/scm/linux/kernel/git/trace/linux-trace:
printf: Remove unused 'bprintf'
Pull timer fixes from Borislav Petkov:
- Fix a case where posix timers with a thread-group-wide target would
miss signals if some of the group's threads are exiting
- Fix a hang caused by ndelay() calling the wrong delay function
__udelay()
- Fix a wrong offset calculation in adjtimex(2) when using ADJ_MICRO
(microsecond resolution) and a negative offset
* tag 'timers_urgent_for_v6.13_rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
posix-timers: Target group sigqueue to current task only if not exiting
delay: Fix ndelay() spuriously treated as udelay()
ntp: Remove invalid cast in time offset math
Pull irq fixes from Borislav Petkov:
- Move the ->select callback to the correct ops structure in
irq-mvebu-sei to fix some Marvell Armada platforms
- Add a workaround for Hisilicon ITS erratum 162100801 which can cause
some virtual interrupts to get lost
- More platform_driver::remove() conversion
* tag 'irq_urgent_for_v6.13_rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
irqchip: Switch back to struct platform_driver::remove()
irqchip/gicv3-its: Add workaround for hip09 ITS erratum 162100801
irqchip/irq-mvebu-sei: Move misplaced select() callback to SEI CP domain
Pull x86 fixes from Borislav Petkov:
- Add a terminating zero end-element to the array describing AMD CPUs
affected by erratum 1386 so that the matching loop actually
terminates instead of going off into the weeds
- Update the boot protocol documentation to mention the fact that the
preferred address to load the kernel to is considered in the
relocatable kernel case too
- Flush the memory buffer containing the microcode patch after applying
microcode on AMD Zen1 and Zen2, to avoid unnecessary slowdowns
- Make sure the PPIN CPU feature flag is cleared on all CPUs if PPIN
has been disabled
* tag 'x86_urgent_for_v6.13_rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/CPU/AMD: Terminate the erratum_1386_microcode array
x86/Documentation: Update algo in init_size description of boot protocol
x86/microcode/AMD: Flush patch buffer mapping after application
x86/mm: Carve out INVLPG inline asm for use by others
x86/cpu: Fix PPIN initialization
The point behind strscpy() was to once and for all avoid all the
problems with 'strncpy()' and later broken "fixed" versions like
strlcpy() that just made things worse.
So strscpy not only guarantees NUL-termination (unlike strncpy), it also
doesn't do unnecessary padding at the destination. But at the same time
also avoids byte-at-a-time reads and writes by _allowing_ some extra NUL
writes - within the size, of course - so that the whole copy can be done
with word operations.
It is also stable in the face of a mutable source string: it explicitly
does not read the source buffer multiple times (so an implementation
using "strnlen()+memcpy()" would be wrong), and does not read the source
buffer past the size (like the mis-design that is strlcpy does).
Finally, the return value is designed to be simple and unambiguous: if
the string cannot be copied fully, it returns an actual negative error,
making error handling clearer and simpler (and the caller already knows
the size of the buffer). Otherwise it returns the string length of the
result.
However, there was one final stability issue that can be important to
callers: the stability of the destination buffer.
In particular, the same way we shouldn't read the source buffer more
than once, we should avoid doing multiple writes to the destination
buffer: first writing a potentially non-terminated string, and then
terminating it with NUL at the end does not result in a stable result
buffer.
Yes, it gives the right result in the end, but if the rule for the
destination buffer was that it is _always_ NUL-terminated even when
accessed concurrently with updates, the final byte of the buffer needs
to always _stay_ as a NUL byte.
[ Note that "final byte is NUL" here is literally about the final byte
in the destination array, not the terminating NUL at the end of the
string itself. There is no attempt to try to make concurrent reads and
writes give any kind of consistent string length or contents, but we
do want to guarantee that there is always at least that final
terminating NUL character at the end of the destination array if it
existed before ]
This is relevant in the kernel for the tsk->comm[] array, for example.
Even without locking (for either readers or writers), we want to know
that while the buffer contents may be garbled, it is always a valid C
string and always has a NUL character at 'comm[TASK_COMM_LEN-1]' (and
never has any "out of thin air" data).
So avoid any "copy possibly non-terminated string, and terminate later"
behavior, and write the destination buffer only once.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Pull turbostat updates from Len Brown:
- assorted minor bug fixes
- assorted platform specific tweaks
- initial RAPL PSYS (SysWatt) support
* tag 'turbostat-2024.11.30' of git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux:
tools/power turbostat: 2024.11.30
tools/power turbostat: Add RAPL psys as a built-in counter
tools/power turbostat: Fix child's argument forwarding
tools/power turbostat: Force --no-perf in --dump mode
tools/power turbostat: Add support for /sys/class/drm/card1
tools/power turbostat: Cache graphics sysfs file descriptors during probe
tools/power turbostat: Consolidate graphics sysfs access
tools/power turbostat: Remove unnecessary fflush() call
tools/power turbostat: Enhance platform divergence description
tools/power turbostat: Add initial support for GraniteRapids-D
tools/power turbostat: Remove PC3 support on Lunarlake
tools/power turbostat: Rename arl_features to lnl_features
tools/power turbostat: Add back PC8 support on Arrowlake
tools/power turbostat: Remove PC7/PC9 support on MTL
tools/power turbostat: Honor --show CPU, even when even when num_cpus=1
tools/power turbostat: Fix trailing '\n' parsing
tools/power turbostat: Allow using cpu device in perf counters on hybrid platforms
tools/power turbostat: Fix column printing for PMT xtal_time counters
tools/power turbostat: fix GCC9 build regression
Pull PCI fix from Bjorn Helgaas:
- When removing a PCI device, only look up and remove a platform device
if there is an associated device node for which there could be a
platform device, to fix a merge window regression (Brian Norris)
* tag 'pci-v6.13-fixes-1' of git://git.kernel.org/pub/scm/linux/kernel/git/pci/pci:
PCI/pwrctrl: Unregister platform device only if one actually exists
Pull ima fix from Paul Moore:
"One small patch to fix a function parameter / local variable naming
snafu that went up to you in the current merge window"
* tag 'lsm-pr-20241129' of git://git.kernel.org/pub/scm/linux/kernel/git/pcmoore/lsm:
ima: uncover hidden variable in ima_match_rules()
Pull more block updates from Jens Axboe:
- NVMe pull request via Keith:
- Use correct srcu list traversal (Breno)
- Scatter-gather support for metadata (Keith)
- Fabrics shutdown race condition fix (Nilay)
- Persistent reservations updates (Guixin)
- Add the required bits for MD atomic write support for raid0/1/10
- Correct return value for unknown opcode in ublk
- Fix deadlock with zone revalidation
- Fix for the io priority request vs bio cleanups
- Use the correct unsigned int type for various limit helpers
- Fix for a race in loop
- Cleanup blk_rq_prep_clone() to prevent uninit-value warning and make
it easier for actual humans to read
- Fix potential UAF when iterating tags
- A few fixes for bfq-iosched UAF issues
- Fix for brd discard not decrementing the allocated page count
- Various little fixes and cleanups
* tag 'block-6.13-20242901' of git://git.kernel.dk/linux: (36 commits)
brd: decrease the number of allocated pages which discarded
block, bfq: fix bfqq uaf in bfq_limit_depth()
block: Don't allow an atomic write be truncated in blkdev_write_iter()
mq-deadline: don't call req_get_ioprio from the I/O completion handler
block: Prevent potential deadlock in blk_revalidate_disk_zones()
block: Remove extra part pointer NULLify in blk_rq_init()
nvme: tuning pr code by using defined structs and macros
nvme: introduce change ptpl and iekey definition
block: return bool from get_disk_ro and bdev_read_only
block: remove a duplicate definition for bdev_read_only
block: return bool from blk_rq_aligned
block: return unsigned int from blk_lim_dma_alignment_and_pad
block: return unsigned int from queue_dma_alignment
block: return unsigned int from bdev_io_opt
block: req->bio is always set in the merge code
block: don't bother checking the data direction for merges
block: blk-mq: fix uninit-value in blk_rq_prep_clone and refactor
Revert "block, bfq: merge bfq_release_process_ref() into bfq_put_cooperator()"
md/raid10: Atomic write support
md/raid1: Atomic write support
...
Pull more io_uring updates from Jens Axboe:
- Remove a leftover struct from when the cqwait registered waiting was
transitioned to regions.
- Fix for an issue introduced in this merge window, where nop->fd might
be used uninitialized. Ensure it's always set.
- Add capping of the task_work run in local task_work mode, to prevent
bursty and long chains from adding too much latency.
- Work around xa_store() leaving ->head non-NULL if it encounters an
allocation error during storing. Just a debug trigger, and can go
away once xa_store() behaves in a more expected way for this
condition. Not a major thing as it basically requires fault injection
to trigger it.
- Fix a few mapping corner cases
- Fix KCSAN complaint on reading the table size post unlock. Again not
a "real" issue, but it's easy to silence by just keeping the reading
inside the lock that protects it.
* tag 'io_uring-6.13-20242901' of git://git.kernel.dk/linux:
io_uring/tctx: work around xa_store() allocation error issue
io_uring: fix corner case forgetting to vunmap
io_uring: fix task_work cap overshooting
io_uring: check for overflows in io_pin_pages
io_uring/nop: ensure nop->fd is always initialized
io_uring: limit local tw done
io_uring: add io_local_work_pending()
io_uring/region: return negative -E2BIG in io_create_region()
io_uring: protect register tracing
io_uring: remove io_uring_cqwait_reg_arg
Pull dma-mapping fix from Christoph Hellwig:
- fix physical address calculation for struct dma_debug_entry (Fedor
Pchelkin)
* tag 'dma-mapping-6.13-2024-11-30' of git://git.infradead.org/users/hch/dma-mapping:
dma-debug: fix physical address calculation for struct dma_debug_entry
Pull more kvm updates from Paolo Bonzini:
- ARM fixes
- RISC-V Svade and Svadu (accessed and dirty bit) extension support for
host and guest
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm:
KVM: riscv: selftests: Add Svade and Svadu Extension to get-reg-list test
RISC-V: KVM: Add Svade and Svadu Extensions Support for Guest/VM
dt-bindings: riscv: Add Svade and Svadu Entries
RISC-V: Add Svade and Svadu Extensions Support
KVM: arm64: Use MDCR_EL2.HPME to evaluate overflow of hyp counters
KVM: arm64: Ignore PMCNTENSET_EL0 while checking for overflow status
KVM: arm64: Mark set_sysreg_masks() as inline to avoid build failure
KVM: arm64: vgic-its: Add stronger type-checking to the ITS entry sizes
KVM: arm64: vgic: Kill VGIC_MAX_PRIVATE definition
KVM: arm64: vgic: Make vgic_get_irq() more robust
KVM: arm64: vgic-v3: Sanitise guest writes to GICR_INVLPIR
Pull sh updates from John Paul Adrian Glaubitz:
"Two small fixes.
The first one by Huacai Chen addresses a runtime warning when
CONFIG_CPUMASK_OFFSTACK and CONFIG_DEBUG_PER_CPU_MAPS are selected
which occurs because the cpuinfo code on sh incorrectly uses NR_CPUS
when iterating CPUs instead of the runtime limit nr_cpu_ids.
A second fix by Dan Carpenter fixes a use-after-free bug in
register_intc_controller() which occurred as a result of improper
error handling in the interrupt controller driver code when
registering an interrupt controller during plat_irq_setup() on sh"
* tag 'sh-for-v6.13-tag1' of git://git.kernel.org/pub/scm/linux/kernel/git/glaubitz/sh-linux:
sh: intc: Fix use-after-free bug in register_intc_controller()
sh: cpuinfo: Fix a warning for CONFIG_CPUMASK_OFFSTACK
Pull arm64 fixes from Catalin Marinas:
- Deselect ARCH_CORRECT_STACKTRACE_ON_KRETPROBE so that tests depending
on it don't run (and fail) on arm64
- Fix lockdep assert in the Arm SMMUv3 PMU driver
- Fix the port and device ID bits setting in the Arm CMN perf driver
* tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux:
perf/arm-cmn: Ensure port and device id bits are set properly
perf/arm-smmuv3: Fix lockdep assert in ->event_init()
arm64: disable ARCH_CORRECT_STACKTRACE_ON_KRETPROBE tests
since 2024.07.26:
assorted minor bug fixes
assorted platform specific tweaks
initial RAPL PSYS (SysWatt) support
Signed-off-by: Len Brown <len.brown@intel.com>
Introduce the counter as a part of global, platform counters structure.
We open the counter for only one cpu, but otherwise treat it as an
ordinary RAPL counter, allowing for grouped perf read.
The counter is disabled by default, because it's interpretation may
require additional, platform specific information, making it unsuitable
for general use.
Signed-off-by: Patryk Wlazlyn <patryk.wlazlyn@linux.intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Add '+' to optstring when early scanning for --no-msr and --no-perf.
It causes option processing to stop as soon as a nonoption argument is
encountered, effectively skipping child's arguments.
Fixes: 3e4048466c ("tools/power turbostat: Add --no-msr option")
Signed-off-by: Patryk Wlazlyn <patryk.wlazlyn@linux.intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Force the --no-perf early to prevent using it as a source. User asks for
raw values, but perf returns them relative to the opening of the file
descriptor.
Signed-off-by: Patryk Wlazlyn <patryk.wlazlyn@linux.intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
On some machines, the graphics device is enumerated as
/sys/class/drm/card1 instead of /sys/class/drm/card0. The current
implementation does not handle this scenario, resulting in the loss of
graphics C6 residency and frequency information.
Add support for /sys/class/drm/card1, ensuring that turbostat can
retrieve and display the graphics columns for these platforms.
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
