Add support for two configurations with SoundWire mockup devices that
emulate the two CometLake configurations with one and two amps. This
patch helps test the SOF firmware on an UpExtreme board without any
hardware connected, e.g. by doing a loopback of the playback stream on
capture streams.
The mapping of the partIDs is as follows:
0xAAAA: generic full-duplex codec (not currently used)
0xAA55: headset codec (mock-up of RT711/RT5682) - full-duplex
0x55AA: amplifier (mock-up of RT1308/RT1316/Maxim 98373) - playback
with IV sense feedback
0x5555: mic codec (mock-up of RT715) - capture-only
The tables are added in a separate file to allow for mockup codecs to be
added on other platforms, but the mapping to specific topologies
remains platform-specific.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Rander Wang <rander.wang@intel.com>
Signed-off-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Link: https://lore.kernel.org/r/20210714032209.11284-3-yung-chuan.liao@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
To test the host controller and bus management code, it is currently
required to have a physical SoundWire peripheral attached to the
bus. To help with pre-silicon or early hardware enablement, it would
be very useful to have a SoundWire 'mockup' device that is exposed in
platform firmware but does not drive any signal on the bus.
This is different to the existing ASoC 'dummy' codec uses for I2S/TDM,
the SoundWire spec makes it clear that a device that is not attached
to the bus is not permitted to interact with the bus, be it for
command/control or data.
This patch exposes a 'mockup' device, with a minimalist driver, with 4
partID values reserved by Intel for such test configurations. The
mockup device exposes one full-duplex DAI based on 2 ports (DP1 for
playback and DP8 for capture). The capture data port is just virtual,
such a mockup device is prevented by the SoundWire specification from
presenting any data generated by a Source port without being Attached.
All the callbacks exposed by the SoundWire Slave interface are
populated, even if they just return immediately. This is intentional
to describe what a minimal codec driver should do and implement and
help new codec vendors provide support for their devices.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Rander Wang <rander.wang@intel.com>
Signed-off-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Link: https://lore.kernel.org/r/20210714032209.11284-2-yung-chuan.liao@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Hi,
Changes since v1:
- Do not calculat that we allow one serializer in DIT mode, just set the
max_active_serializers to 1.
Reported-by: kernel test robot <lkp@intel.com>
it has been on my todo list for several years to support McASP on OMAP4 devices.
For Galaxy Nexus we had an omap-mcasp driver (which was mostly a stripped down
davinci-mcasp driver) to support what was needed on that specific phone + it's
dock for S/PDIF (48KHz, 16bit, stereo).
Not many (if any) device available to test the DIT mode of McASP.
I have used BeagleBone White (McASP1 AXR3 can be routed to a pin) to get the
S/PDIF mode working then PandaES for OMAP4 support (on PandaES the gpio_121 is
not used and the signal is routed to expansion J6 pin14).
In theory the McASP in OMAP5 should be working after this series, but the OMAP5
TRM is not public and I do not have one to check the addresses and see if there
is a way to test it on omap5-uevm.
Mark, Tony:
The ASoC and dts patches can go via separate tree I felt that it is better if
they are together, at least initially.
Nikolaus: fyi, this might be useful for Pyra?
Regards,
Péter
---
Peter Ujfalusi (5):
ASoC: ti: davinci-mcasp: Fix DIT mode support
ASoC: dt-bindings: davinci-mcasp: Add compatible string for OMAP4
ASoC: ti: davinci-mcasp: Add support for the OMAP4 version of McASP
ARM: dts: omap4-l4-abe: Correct sidle modes for McASP
ARM: dts: omap4-l4-abe: Add McASP configuration
.../bindings/sound/davinci-mcasp-audio.txt | 1 +
arch/arm/boot/dts/omap4-l4-abe.dtsi | 39 ++--
include/linux/platform_data/davinci_asp.h | 1 +
sound/soc/ti/Kconfig | 1 +
sound/soc/ti/davinci-mcasp.c | 176 +++++++++++++++---
5 files changed, 175 insertions(+), 43 deletions(-)
--
2.32.0
The first fix solves an underflow in SoundWire platforms using the
max98373 amplifier, the rest of the patches are minor corrections in
machine drivers.
The fix should be queued for the 5.14 cycle, the rest should be
harmless but can be deferred for 5.15 if it's too late already.
Brent Lu (2):
ASoC: SOF: add a helper to get topology configured bclk
ASoC: Intel: sof_cs42l42: use helper function to get bclk frequency
Gongjun Song (1):
ASoC: Intel: soc-acpi: add support for SoundWire of TGL-H-RVP
Rander Wang (1):
ASoC: Intel: boards: fix xrun issue on platform with max98373
include/sound/sof.h | 1 +
sound/soc/intel/boards/sof_cs42l42.c | 8 +-
sound/soc/intel/boards/sof_sdw_max98373.c | 81 ++++++++++++-------
.../intel/common/soc-acpi-intel-tgl-match.c | 15 ++++
sound/soc/sof/sof-audio.c | 42 ++++++++--
5 files changed, 111 insertions(+), 36 deletions(-)
--
2.25.1
The TAS2505/TAS2521 does support up to two channels, LEFT and RIGHT,
which are being alternated on the audio data bus by Word Clock, WCLK.
This is documented in TI slau472 2.7.1 Digital Audio Interface. Note
that both the LEFT and RIGHT channels are only used for audio INPUT,
while only the LEFT channel is used for audio OUTPUT.
Fixes: b4525b6196 ("ASoC: tlv320aic32x4: add support for TAS2505")
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Claudius Heine <ch@denx.de>
Cc: Mark Brown <broonie@kernel.org>
Link: https://lore.kernel.org/r/20210708091229.56443-1-marex@denx.de
Signed-off-by: Mark Brown <broonie@kernel.org>
OMAP4 has one McASP instance with single serializer and supporting only
DIT mode.
According to the TRM the DAT port needs to be accessed as specific offset
compared to other devices where access to any part of the DAT region is
valid.
To handle this constraint we need to introduce a new compatiple string for
OMAP4.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@gmail.com>
Link: https://lore.kernel.org/r/20210705194249.2385-3-peter.ujfalusi@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The DIT mode support has not been tested due to lack of platform where it
can be tested.
To be able to use the McASP on OMAP4/5 (only supporting DIT mode) we need
to have DIT mode working in the McASP driver on a know platform.
After hacking around (on BBW, mcasp1.axr1 can be routed out for this) it
appeared that DIT mode is broken.
This patch fixes it up and 16/24 bit audio works along with passthrough,
but I have only tested with DTS example and test files.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@gmail.com>
Link: https://lore.kernel.org/r/20210705194249.2385-2-peter.ujfalusi@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The kernel recovers in due course from missing Mlocked pages: but there
was no point in calling page_mlock() (formerly known as
try_to_munlock()) on a THP, because nothing got done even when it was
found to be mapped in another VM_LOCKED vma.
It's true that we need to be careful: Mlocked accounting of pte-mapped
THPs is too difficult (so consistently avoided); but Mlocked accounting
of only-pmd-mapped THPs is supposed to work, even when multiple mappings
are mlocked and munlocked or munmapped. Refine the tests.
There is already a VM_BUG_ON_PAGE(PageDoubleMap) in page_mlock(), so
page_mlock_one() does not even have to worry about that complication.
(I said the kernel recovers: but would page reclaim be likely to split
THP before rediscovering that it's VM_LOCKED? I've not followed that up)
Fixes: 9a73f61bdb ("thp, mlock: do not mlock PTE-mapped file huge pages")
Signed-off-by: Hugh Dickins <hughd@google.com>
Reviewed-by: Shakeel Butt <shakeelb@google.com>
Acked-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Link: https://lore.kernel.org/lkml/cfa154c-d595-406-eb7d-eb9df730f944@google.com/
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Alistair Popple <apopple@nvidia.com>
Cc: Jason Gunthorpe <jgg@nvidia.com>
Cc: Ralph Campbell <rcampbell@nvidia.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Yang Shi <shy828301@gmail.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Pull irq fixes from Ingo Molnar:
"Two fixes:
- Fix a MIPS IRQ handling RCU bug
- Remove a DocBook annotation for a parameter that doesn't exist
anymore"
* tag 'irq-urgent-2021-07-11' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
irqchip/mips: Fix RCU violation when using irqdomain lookup on interrupt entry
genirq/irqdesc: Drop excess kernel-doc entry @lookup
Pull scheduler fixes from Ingo Molnar:
"Three fixes:
- Fix load tracking bug/inconsistency
- Fix a sporadic CFS bandwidth constraints enforcement bug
- Fix a uclamp utilization tracking bug for newly woken tasks"
* tag 'sched-urgent-2021-07-11' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
sched/uclamp: Ignore max aggregation if rq is idle
sched/fair: Fix CFS bandwidth hrtimer expiry type
sched/fair: Sync load_sum with load_avg after dequeue
Pull perf fixes from Ingo Molnar:
"A fix and a hardware-enablement addition:
- Robustify uncore_snbep's skx_iio_set_mapping()'s error cleanup
- Add cstate event support for Intel ICELAKE_X and ICELAKE_D"
* tag 'perf-urgent-2021-07-11' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
perf/x86/intel/uncore: Clean up error handling path of iio mapping
perf/x86/cstate: Add ICELAKE_X and ICELAKE_D support
Pull locking fixes from Ingo Molnar:
- Fix a Sparc crash
- Fix a number of objtool warnings
- Fix /proc/lockdep output on certain configs
- Restore a kprobes fail-safe
* tag 'locking-urgent-2021-07-11' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
locking/atomic: sparc: Fix arch_cmpxchg64_local()
kprobe/static_call: Restore missing static_call_text_reserved()
static_call: Fix static_call_text_reserved() vs __init
jump_label: Fix jump_label_text_reserved() vs __init
locking/lockdep: Fix meaningless /proc/lockdep output of lock classes on !CONFIG_PROVE_LOCKING
Pull more SCSI updates from James Bottomley:
"This is a set of minor fixes and clean ups in the core and various
drivers.
The only core change in behaviour is the I/O retry for spinup notify,
but that shouldn't impact anything other than the failing case"
* tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: (23 commits)
scsi: virtio_scsi: Add validation for residual bytes from response
scsi: ipr: System crashes when seeing type 20 error
scsi: core: Retry I/O for Notify (Enable Spinup) Required error
scsi: mpi3mr: Fix warnings reported by smatch
scsi: qedf: Add check to synchronize abort and flush
scsi: MAINTAINERS: Add mpi3mr driver maintainers
scsi: libfc: Fix array index out of bound exception
scsi: mvsas: Use DEVICE_ATTR_RO()/RW() macro
scsi: megaraid_mbox: Use DEVICE_ATTR_ADMIN_RO() macro
scsi: qedf: Use DEVICE_ATTR_RO() macro
scsi: qedi: Use DEVICE_ATTR_RO() macro
scsi: message: mptfc: Switch from pci_ to dma_ API
scsi: be2iscsi: Fix some missing space in some messages
scsi: be2iscsi: Fix an error handling path in beiscsi_dev_probe()
scsi: ufs: Fix build warning without CONFIG_PM
scsi: bnx2fc: Remove meaningless bnx2fc_abts_cleanup() return value assignment
scsi: qla2xxx: Add heartbeat check
scsi: virtio_scsi: Do not overwrite SCSI status
scsi: libsas: Add LUN number check in .slave_alloc callback
scsi: core: Inline scsi_mq_alloc_queue()
...
Pull more perf tool updates from Arnaldo Carvalho de Melo:
"New features:
- Enable use of BPF counters with 'perf stat --for-each-cgroup',
using per-CPU 'cgroup-switch' events with an attached BPF program
that does aggregation per-cgroup in the kernel instead of using
per-cgroup perf events.
- Add Topdown metrics L2 events as default events in 'perf stat' for
systems having those events.
Hardware tracing:
- Add a config for max loops without consuming a packet in the Intel
PT packet decoder, set via 'perf config intel-pt.max-loops=N'
Hardware enablement:
- Disable misleading NMI watchdog message in 'perf stat' on hybrid
systems such as Intel Alder Lake.
- Add a dummy event on hybrid systems to collect metadata records.
- Add 24x7 nest metric events for the Power10 platform.
Fixes:
- Fix event parsing for PMUs starting with the same prefix.
- Fix the 'perf trace' 'trace' alias installation dir.
- Fix buffer size to report iregs in perf script python scripts,
supporting the extended registers in PowerPC.
- Fix overflow in elf_sec__is_text().
- Fix 's' on source line when disasm is empty in the annotation TUI,
accessible via 'perf annotate', 'perf report' and 'perf top'.
- Plug leaks in scandir() returned dirent entries in 'perf test' when
sorting the shell tests.
- Fix --task and --stat with pipe input in 'perf report'.
- Fix 'perf probe' use of debuginfo files by build id.
- If a DSO has both dynsym and symtab ELF sections, read from both
when loading the symbol table, fixing a problem processing Fedora
32 glibc DSOs.
Libraries:
- Add grouping of events to libperf, from code in tools/perf,
allowing libperf users to use that mode.
Misc:
- Filter plt stubs from the 'perf probe --functions' output.
- Update UAPI header copies for asound, DRM, mman-common.h and the
ones affected by the quotactl_fd syscall"
* tag 'perf-tools-for-v5.14-2021-07-10' of git://git.kernel.org/pub/scm/linux/kernel/git/acme/linux: (29 commits)
perf test: Add free() calls for scandir() returned dirent entries
libperf: Add tests for perf_evlist__set_leader()
libperf: Remove BUG_ON() from library code in get_group_fd()
libperf: Add group support to perf_evsel__open()
perf tools: Fix pattern matching for same substring in different PMU type
perf record: Add a dummy event on hybrid systems to collect metadata records
perf stat: Add Topdown metrics L2 events as default events
libperf: Adopt evlist__set_leader() from tools/perf as perf_evlist__set_leader()
libperf: Move 'nr_groups' from tools/perf to evlist::nr_groups
libperf: Move 'leader' from tools/perf to perf_evsel::leader
libperf: Move 'idx' from tools/perf to perf_evsel::idx
libperf: Change tests to single static and shared binaries
perf intel-pt: Add a config for max loops without consuming a packet
perf stat: Disable the NMI watchdog message on hybrid
perf vendor events power10: Adds 24x7 nest metric events for power10 platform
perf script python: Fix buffer size to report iregs in perf script
perf trace: Fix the perf trace link location
perf top: Fix overflow in elf_sec__is_text()
perf annotate: Fix 's' on source line when disasm is empty
perf probe: Do not show @plt function by default
...
Commit dbbee9d5cd ("mm/page_alloc: convert per-cpu list protection to
local_lock") folded in a workaround patch for pahole that was unable to
deal with zero-sized percpu structures.
A superior workaround is achieved with commit a0b8200d06 ("kbuild:
skip per-CPU BTF generation for pahole v1.18-v1.21").
This patch reverts the dummy field and the pahole version check.
Fixes: dbbee9d5cd ("mm/page_alloc: convert per-cpu list protection to local_lock")
Signed-off-by: Mel Gorman <mgorman@techsingularity.net>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Pull cifs fixes from Steve French:
"13 cifs/smb3 fixes. Most are to address minor issues pointed out by
Coverity.
Also includes a packet signing enhancement and mount improvement"
* tag '5.14-rc-smb3-fixes-part2' of git://git.samba.org/sfrench/cifs-2.6:
cifs: update internal version number
cifs: prevent NULL deref in cifs_compose_mount_options()
SMB3.1.1: Add support for negotiating signing algorithm
cifs: use helpers when parsing uid/gid mount options and validate them
CIFS: Clarify SMB1 code for POSIX Lock
CIFS: Clarify SMB1 code for rename open file
CIFS: Clarify SMB1 code for delete
CIFS: Clarify SMB1 code for SetFileSize
smb3: fix typo in header file
CIFS: Clarify SMB1 code for UnixSetPathInfo
CIFS: Clarify SMB1 code for UnixCreateSymLink
cifs: clarify SMB1 code for UnixCreateHardLink
cifs: make locking consistent around the server session status
Pull i3c updates from Alexandre Belloni:
- two small fixes to the svc driver
* tag 'i3c/for-5.14' of git://git.kernel.org/pub/scm/linux/kernel/git/i3c/linux:
i3c: master: svc: fix doc warning in svc-i3c-master.c
i3c: master: svc: drop free_irq of devm_request_irq allocated irq
