To support ycbcr output, we need a pipe CSC block to do
RGB->YCBCR conversion.
Current Intel platforms have only one pipe CSC unit, so
we can either do color correction using it, or we can perform
RGB->YCBCR conversion.
This function adds a csc handler, which uses recommended bspec
values to perform RGB->YCBCR conversion (target color space BT709)
V2: Rebase
V3: Rebase
V4: Rebase
V5: Addressed review comments from Ander
- Remove extra line added in the patch
- Add the spec details in the commit message
- Combine two if(cond) while calling intel_crtc_compute_config
V6: Handle YCBCR420 outputs only (Ville)
V7: Addressed review comments from Ville:
- Add description about target colorspace
- Remove the comments from CSC function
- DRM_DEBUG->DEBUG_KMS for atomic failure due to CSC unit busy
- Remove unnecessary debug message about YCBCR420 possibe
V8: Addressed review comments from Ville:
- Remove extra comment, not required.
- Do not add extra variable for CTM, reuse pipe_config
Added r-b from Ville
V9: Remove extra whitespace (Imre)
V10: Added r-b from Imre
Cc: Ville Syrjala <ville.syrjala@linux.intel.com>
Cc: Daniel Vetter <daniel.vetter@intel.com>
Cc: Ander Conselvan de Oliveira <conselvan2@gmail.com>
Cc: Imre Deak <imre.deak@intel.com>
Reviewed-by: Ville Syrjala <ville.syrjala@linux.intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Shashank Sharma <shashank.sharma@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/1500650709-14447-5-git-send-email-shashank.sharma@intel.com
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
To get HDMI YCBCR420 output, the PIPEMISC register should be
programmed to:
- Generate YCBCR output (bit 11)
- In case of YCBCR420 outputs, it should be programmed in full
blend mode to use the scaler in 5x3 ratio (bits 26 and 27)
This patch:
- Adds definition of these bits.
- Programs PIPEMISC for YCBCR420 outputs.
- Adds readouts to compare HW and SW states.
V2: rebase
V3: rebase
V4: rebase
V5: added r-b from Ander
V6: Handle only YCBCR420 outputs (ville)
V7: rebase
V8: Addressed review comments from Ville
- Add readouts for state->ycbcr420 and 420 pixel_clock.
- Handle warning due to mismatch in clock for ycbcr420 clock.
- Rename PIPEMISC macros to match the Bspec.
- Add a debug print stating if YCBCR 4:2:0 output enabled.
Added r-b from Ville
V9: Addressed review comments from Imre:
- Add 420 mode clock adjustment in intel_hdmi_mode_valid to
prevent 420_only modes getting rejected for high clock.
- Add port clock adjustment for ycbcr420 modes in ddi_get_clock
- Rename macros as per Ville's suggestion.
- Remove unnecessary wl changes.
V10: Added r-b from Imre
V11: Fixed faulty dotclock handling, and addressed missing comment
from previous set of review comments (Imre)
V12: Fixed dotclock for 12bpc too, removed 420 check for GEN < 10
Cc: Ville Syrjala <ville.syrjala@linux.intel.com>
Cc: Ander Conselvan de Oliveira <conselvan2@gmail.com>
Cc: Daniel Vetter <daniel.vetter@intel.com>
Cc: Imre Deak <imre.deak@intel.com>
Reviewed-by: Ander Conselvan de Oliveira <conselvan2@gmail.com>
Reviewed-by: Ville Syrjala <ville.syrjala@linux.intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Shashank Sharma <shashank.sharma@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/1500904172-31717-1-git-send-email-shashank.sharma@intel.com
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
To get a YCBCR420 output from intel platforms, we need one
scaler to scale down YCBCR444 samples to YCBCR420 samples.
This patch:
- Does scaler allocation for HDMI ycbcr420 outputs.
- Programs PIPE_MISC register for ycbcr420 output.
V2: rebase
V3: rebase
V4: rebase
V5: addressed review comments from Ander:
- No need to check both scaler_user && hdmi_output.
Check for scaler_user is enough.
V6: rebase
V7: Do not create a new scaler user, use existing pipe scaler user.
V8: rebase
V9: Addressed review comments from Ville:
- Remove leftover comment for HDMI scaler user.
- Remove unnecessary blank line.
- Make scaler alocation failure a DEBUG log instead of ERROR.
Added r-b from Ville
V10: Update commit message as per latest code (Imre)
Added r-b from Imre
Cc: Ville Syrjala <ville.syrjala@linux.intel.com>
Cc: Ander Conselvan De Oliveira <conselvan2@gmail.com>
Cc: Imre Deak <imre.deak@intel.com>
Reviewed-by: Ville Syrjala <ville.syrjala@linux.intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Shashank Sharma <shashank.sharma@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/1500650709-14447-3-git-send-email-shashank.sharma@intel.com
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This patch checks encoder level support for YCBCR420 outputs.
The logic goes as simple as this:
If the input mode is YCBCR420-only mode: prepare HDMI for
YCBCR420 output, else continue with RGB output mode.
It checks if the mode is YCBCR420 and source can support this
output then it marks the ycbcr_420 output indicator into crtc
state, for further staging in driver.
V2: Split the patch into two, kept helper functions in DRM layer.
V3: Changed the compute_config function based on new DRM API.
V4: Rebase
V5: Rebase
V6: Check and handle YCBCR420-only modes, discard the property
based approach (Ville)
V7: Addressed review comments from Ville
- add else case in 12BPC check.
- extract ycbcr420 state inside hdmi_12bpc_possible function.
V8: Addressed review comments from Ville
- Remove extra blank lines.
- Remove "HDMI" from the description of ycbcr420 state variable.
- Remove local variable, use crtc_state->ycbcr420 instead.
Added r-b from Ville.
V9: Rebase
V10: Added r-b from Imre
Cc: Ville Syrjala <ville.syrjala@linux.intel.com>
Cc: Daniel Vetter <daniel.vetter@intel.com>
Cc: Ander Conselvan de Oliveira <conselvan2@gmail.com>
Reviewed-by: Ville Syrjala <ville.syrjala@linux.intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Shashank Sharma <shashank.sharma@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/1500650709-14447-2-git-send-email-shashank.sharma@intel.com
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The pattern of a power well backing a set of fuses whose initialization
we need to wait for during power well enabling is common to all GEN9+
platforms. Adding support for this to the HSW power well enable helper
allows us to use the HSW/BDW power well code for GEN9+ as well in a
follow-up patch.
v2:
- Use an enum for power gates instead of raw numbers. (Ville)
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Arkadiusz Hiler <arkadiusz.hiler@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20170711204236.5618-6-imre.deak@intel.com
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The pattern of a power well backing a set of pipe IRQ or VGA
functionality applies to all HSW+ platforms. Using power well attributes
instead of platform checks to decide whether to init/reset pipe IRQs and
VGA correspondingly is cleaner and it allows us to unify the HSW/BDW and
GEN9+ power well code in follow-up patches.
Also use u8 for pipe_mask in related helpers to match the type in the
power well struct.
v2:
- Use u8 instead of u32 for irq_pipe_mask. (Ville)
v3:
- Use u8 for pipe_mask in related helpers too for clarity.
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Arkadiusz Hiler <arkadiusz.hiler@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20170712155413.29839-1-imre.deak@intel.com
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Although on HSW/BDW there is only a single display global power well,
it's programmed the same way as other GEN9+ power wells. This also
means we can get at the HSW/BDW request and status flags the same way
it's done on GEN9+ by assigning the corresponding HSW/BDW power well ID.
This ID was assigned in a recent patch, so we can now switch to using
the same macros everywhere on HSW+.
Updating the HSW power well control register with RMW is not strictly
necessary, but this will allow us to use the same code for GEN9+.
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Arkadiusz Hiler <arkadiusz.hiler@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/1499352040-8819-13-git-send-email-imre.deak@intel.com
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Atm, the power well IDs are defined in separate platform specific enums,
which isn't ideal for the following reasons:
- the IDs are used by helpers like lookup_power_well() in a platform
independent way
- the always-on power well is used by multiple platforms and so needs
now separate IDs, although these IDs refer to the same thing
To make things more consistent use a single enum instead of the two
separate ones, listing the IDs per platform (or set of very similar
platforms like all GEN9/10). Replace the separate always-on power
well IDs with a single ID.
While at it also add a note clarifying the distinction between regular
power wells that follow a common programming pattern and custom ones
that are programmed in some other way. The IDs for regular power wells
need to stay fixed, since they also define the request and state HW flag
positions in their corresponding power well control register(s).
v2:
- Add comment about id to req,status bit mapping to the enum. (Rodrigo)
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20170711204236.5618-1-imre.deak@intel.com
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The scaler allocation code depends on a non-zero default value for the
crtc scaler_id, so make sure we initialize the scaler state accordingly
even if the crtc is off. This fixes at least an initial YUV420 modeset
(added in a follow-up patchset by Shashank) when booting with the screen
off: after the initial HW readout and modeset which enables the scaler a
subsequent modeset will disable the scaler which isn't properly
allocated. This results in a funky HW state where the pipe scaler HW
registers can't be modified and the normally black screen is grey and
shifted to the right or jitters.
The problem was revealed by Shashank's YUV420 patchset and first
reported by Ville.
v2:
- In the stable tag also include versions which need backporting (Jani)
Cc: Jani Nikula <jani.nikula@intel.com>
Cc: Shashank Sharma <shashank.sharma@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Chandra Konduru <chandra.konduru@intel.com>
Cc: Matt Roper <matthew.d.roper@intel.com>
Cc: <stable@vger.kernel.org> # 4.2.x
Reported-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Fixes: a1b2278e4d ("drm/i915: skylake panel fitting using shared scalers")
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Mahesh Kumar <mahesh1.kumar@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20170720112820.26816-1-imre.deak@intel.com
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
intel_engine_init_globa_seqno() may be called from an uncontrolled
set-wedged path where we have given up waiting for broken hw and declare
it defunct. Along that path, any sanity checks that the hw is idle
before we adjust its state will expectedly fail, so we simply cannot.
Instead of asserting inside init_global_seqno, we move them to the
normal caller reset_all_global_seqno() as it handles runtime seqno
wraparound.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Mika Kuoppala <mika.kuoppala@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20170721123238.16428-8-chris@chris-wilson.co.uk
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Resync with upstream to avoid git getting too badly confused. Also, we
have a conflict with the drm_vblank_cleanup removal, which cannot be
resolved by simply taking our side. Bake that in properly.
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Hi all,
After merging the drm-misc tree, today's linux-next build (x86_64
allmodconfig) failed like this:
drivers/staging/vboxvideo/vbox_drv.c:235:2: error: unknown field 'set_busid' specified in initializer
.set_busid = drm_pci_set_busid,
^
drivers/staging/vboxvideo/vbox_drv.c:235:15: error: 'drm_pci_set_busid' undeclared here (not in a function)
.set_busid = drm_pci_set_busid,
^
drivers/staging/vboxvideo/vbox_drv.c: In function 'vbox_init':
drivers/staging/vboxvideo/vbox_drv.c:273:9: error: implicit declaration of function 'drm_pci_init' [-Werror=implicit-function-declaration]
return drm_pci_init(&driver, &vbox_pci_driver);
^
drivers/staging/vboxvideo/vbox_drv.c: In function 'vbox_exit':
drivers/staging/vboxvideo/vbox_drv.c:278:2: error: implicit declaration of function 'drm_pci_exit' [-Werror=implicit-function-declaration]
drm_pci_exit(&driver, &vbox_pci_driver);
^
Caused by commits
5c484cee7e ("drm: Remove drm_driver->set_busid hook")
10631d724d ("drm/pci: Deprecate drm_pci_init/exit completely")
interacting with commit
dd55d44f40 ("staging: vboxvideo: Add vboxvideo to drivers/staging")
from the staging.current tree.
I have applied the following merge fix patch - please check that it
is correct.
From: Stephen Rothwell <sfr@canb.auug.org.au>
Date: Wed, 19 Jul 2017 11:41:01 +1000
Subject: [PATCH] drm: fixes for staging due to API changes in the drm core
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Dave Airlie <airlied@redhat.com>
We cannot reference priv->fbdev outside of the #ifdef:
drivers/net/virtio_net.c:1881:12: error: 'virtnet_restore_up' defined but not used [-Werror=unused-function]
static int virtnet_restore_up(struct virtio_device *vdev)
drivers/net/virtio_net.c:1859:13: error: 'virtnet_freeze_down' defined but not used [-Werror=unused-function]
static void virtnet_freeze_down(struct virtio_device *vdev)
As the #ifdef is a bit annoying here, this removes it entirely
and uses an IS_ENABLED() check in it place where needed.
Fixes: b4dd9f1ffaba ("drm/hisilicon: Remove custom FB helper deferred setup")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
[danvet: One step further, also remove the IS_ENABLED checks, core
no-ops out the fb helper functions that the cma helpers use. Discussed
with Arnd on dri-devel.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/20170725180555.3699056-1-arnd@arndb.de
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
