On Raven Invalid PPRs (peripheral page requests) can be reported
because multiple PPRs can be still queued when memory is freed.
Apply a rate limit to avoid flooding the log in this case.
Signed-off-by: Yong Zhao <yong.zhao@amd.com>
Reviewed-by: Felix Kuehling <Felix.Kuehling@amd.com>
Signed-off-by: Felix Kuehling <Felix.Kuehling@amd.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Oded Gabbay <oded.gabbay@gmail.com>
If there are several memory banks that has the same properties in CRAT,
we aggregate them into one memory bank. This cleans up memory banks on
APUs (e.g. Raven) where the CRAT reports each memory channel as a
separate bank. This only confuses user mode, which only deals with
virtual memory.
Signed-off-by: Yong Zhao <yong.zhao@amd.com>
Reviewed-by: Felix Kuehling <Felix.Kuehling@amd.com>
Signed-off-by: Felix Kuehling <Felix.Kuehling@amd.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Oded Gabbay <oded.gabbay@gmail.com>
Compute contexts cannot keep going after a GPU reset. Currently the process
must terminate. In the future a process may be able recreate its context
from scratch. Either way, there is no need to restore the GPUVM page table
from shadow BOs.
Signed-off-by: Shaoyun Liu <Shaoyun.Liu@amd.com>
Reviewed-by: Felix Kuehling <Felix.Kuehling@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Felix Kuehling <Felix.Kuehling@amd.com>
Signed-off-by: Oded Gabbay <oded.gabbay@gmail.com>
Upon VM Fault, the VMID and PASID written by HW are zeros in
Hawaii. Instead of reading from ih_ring_entry, read directly
from the registers. This workaround fix the soft hang issues
caused by mishandled VM Fault in Hawaii.
Signed-off-by: Lan Xiao <Lan.Xiao@amd.com>
Signed-off-by: Felix Kuehling <Felix.Kuehling@amd.com>
Acked-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Oded Gabbay <oded.gabbay@gmail.com>
1. Pre-GFX9 the amdgpu ISR saves the vm-fault status and address per
per-vmid. amdkfd needs to get the information from amdgpu through the
new get_vm_fault_info interface. On GFX9 and later, all the required
information is in the IH ring
2. amdkfd unmaps all queues from the faulting process and create new
run-list without the guilty process
3. amdkfd notifies the runtime of the vm fault trap via EVENT_TYPE_MEMORY
Signed-off-by: shaoyun liu <shaoyun.liu@amd.com>
Signed-off-by: Felix Kuehling <Felix.Kuehling@amd.com>
Acked-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Oded Gabbay <oded.gabbay@gmail.com>
Return ERR_PTR(-EINVAL) if kfd_get_process fails to find the process.
This fixes kernel oopses when a child process calls KFD ioctls with
a file descriptor inherited from the parent process.
Signed-off-by: Wei Lu <wei.lu2@amd.com>
Reviewed-by: Felix Kuehling <Felix.Kuehling@amd.com>
Signed-off-by: Felix Kuehling <Felix.Kuehling@amd.com>
Acked-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Oded Gabbay <oded.gabbay@gmail.com>
The scheduler may raise SQ_WAVE_STATUS.SPI_PRIO via SQ_CMD before
context restore has completed. Restoring SPI_PRIO=0 after this point
may cause context save to fail as the lower priority wavefronts
are not selected for execution among spin-waiting wavefronts.
Leave SPI_PRIO at its SPI-initialized or scheduler-raised value.
v2: Also fix race with exception handler
Signed-off-by: Jay Cornwall <Jay.Cornwall@amd.com>
Reviewed-by: Felix Kuehling <Felix.Kuehling@amd.com>
Signed-off-by: Felix Kuehling <Felix.Kuehling@amd.com>
Acked-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Oded Gabbay <oded.gabbay@gmail.com>
This is needed to prevent deadlocks when MMU notifiers run in
reclaim-FS context and take the DQM lock for userptr evictions.
Previously this was done by making all memory allocations under
DQM locks GFP_NOIO. This is error prone. Using
memalloc_nofs_save/restore will reliably affect all memory
allocations anywhere in the kernel while the DQM lock is held.
Signed-off-by: Felix Kuehling <Felix.Kuehling@amd.com>
Acked-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Oded Gabbay <oded.gabbay@gmail.com>
getrawmonotonic64() and get_monotonic_boottime64() are deprecated
because of the nonstandard naming.
The replacement functions ktime_get_raw_ns() and ktime_get_boot_ns()
also simplify the callers.
Reviewed-by: Felix Kuehling <Felix.Kuehling@amd.com>.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Oded Gabbay <oded.gabbay@gmail.com>
Cleanups
- Change g2d driver to component based driver
. g2d driver was last customed sub driver so this patch series
changes it to component based driver, which also makes gem handling
to be more simplify.
- Cleanup of Exynos DRM suspend/resume
. Register exynos drm core suspend/resume functions
to prepare/complete callbacks of dev_pm_ops instead of suspend/resume
callbacks to ensure exynos_drm_suspend() is called before any suspend
callback from the real devices to avoid some issues on boards with
complex pipelines.
. Also Add pm_runtime_furce_suspend/resume as SYSTEM_SLEEP_PM_OPS
to ensure that resources of each devices will be released
for the system PM suspend/resume cycle.
- Remove local value not used.
Signed-off-by: Dave Airlie <airlied@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/1532505748-10025-1-git-send-email-inki.dae@samsung.com
drm/imx: cleanup and csi improvements
- Remove the unused struct imx_drm_crtc and the unused pipes field
from imx_drm_device and replace drm_dev_unref with drm_dev_put.
- Extend CSI configuration to support RGB888 and BGR888 capture,
as well as 16-bit RGB565 capture via a parallel bus.
- Add CPMEM support for negative interlace offsets, which is
necessary to support writing captured bottom-top interlaced
fields to memory with interleaved lines.
Signed-off-by: Dave Airlie <airlied@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/1532100583.3438.9.camel@pengutronix.de
cik_pcie_gen3_enable() is only called by cik_common_hw_init(), which is
never called in atomic context.
cik_pcie_gen3_enable() calls mdelay() to busily wait, which is not
necessary.
mdelay() can be replaced with msleep().
This is found by a static analysis tool named DCNS written by myself.
Signed-off-by: Jia-Ju Bai <baijiaju1990@gmail.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
The scheduler of the entity is decided by the run queue on which
it is queued. This patch avoids us the effort required to maintain
a sync between rq and sched field when we start shifting entites
among different rqs.
Signed-off-by: Nayan Deshmukh <nayan26deshmukh@gmail.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Going to completely rework the context to ring mapping with Nayan's GSoC
work, but for now just stopping to expose the second UVD instance should
do it.
Signed-off-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Aux engine is created from i2caux layer. We want to remove this layer
and use the engine directly.
[How]
Decouple aux engine from i2caux. Move aux engine related code to dce folder and use
dc resource pool to manage the engine. And use the engine functions directly
Signed-off-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Reviewed-by: Harry Wentland <Harry.Wentland@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
Diags has POR to run the video workload using AYCRCB8888 through DCN;
capture it through DWB and send it to VCN hardware to encode
[how]
added the code to support this format so that DPP ICSC will be able to
convert it from YUV444 to internal RGB and DWB OCSC will be able to
convert from internal RGB to YUV420
Signed-off-by: vikrant mhaske <vikrant.mhaske@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
When a dce100 asic was suspended, the clocks were not set to 0.
Upon resume, the new clock was compared to the existing clock,
they were found to be the same, and so the clock was not set.
This resulted in a pernicious blackscreen.
[How]
In atomic commit, check to see if there are any active pipes.
If no, set clocks to 0
Signed-off-by: David Francis <David.Francis@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
diag specify what the full config and is only concerned about pass/fail at the end
having inter-op code like verifiying we can actually train at reported link rate
slows down diag test and add complexity we don't need
[how]
add dc_debug option to skip capability link trianing
also remove hbr in function name as verify is not specific to hbr
Signed-off-by: Tony Cheng <tony.cheng@amd.com>
Reviewed-by: Ken Chalmers <ken.chalmers@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
