eSR is activated when a chanctx is assigned to more than one link.
During eSR activation we should disable RLC for both phys, and configure
the FW with a special phy command for both phys.
Currently we assign the phy_ctxt to the link only after eSR activation,
so RLC is not disabled for the new phy_ctxt, and a cmd is not sent to FW.
Fix this by first assigning the new phy_ctxt to the link and then
doing the eSR activation.
Fixes: 12bacfc2c0 ("wifi: iwlwifi: handle eSR transitions")
Reviewed-by: Gregory Greenman <gregory.greenman@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://msgid.link/20231219215605.3d94507f5d9a.I537fcd73aedf94c7348c03157e486f24301fef14@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
During ieee80211_set_active_links() we do (among the others):
1. Call drv_change_vif_links() with both old_active and new_active
2. Unassign the chanctx for the removed link(s) (if any)
3. Assign chanctx to the added link(s) (if any)
4. Call drv_change_vif_links() with the new_active links bitmap
The problem here is that during step #1 the driver doesn't know whether
we will activate multiple links simultaneously or are just doing a link
switch, so it can't check there if multiple links are supported/enabled.
(Some of the drivers might enable/disable this option dynamically)
And during step #3, in which the driver already knows that,
returning an error code (for example when multiple links are not
supported or disabled), will cause a warning, and we will still complete
the transition to the new_active links.
(It is hard to undo things in that stage, since we released channels etc.)
Therefore add a driver callback to check if the desired new_active links
will be supported by the driver or not. This callback will be called
in the beginning of ieee80211_set_active_links() so we won't do anything
before we are sure it is supported.
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Reviewed-by: Gregory Greenman <gregory.greenman@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Link: https://msgid.link/20231220133549.64c4d70b33b8.I79708619be76b8ecd4ef3975205b8f903e24a2cd@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
It is possible for the TX status report for the (Re)Association Request
frame to be delayed long enough for the AP's (Re)Association Response
frame to be received and processed before it. If that were to happen for
a case where the AP rejects the association with indication to come back
later, the association timeout and retry state should not be modified
anymore with the TX status information that would be processed after
this. Updating the association timeout in such a reverse order of events
could result in shortening the timeouts for the association comeback
mechanism and that could result in the association failing.
Track whether we have already processed association rejection with
comeback time and if so, skip the timeout and retry update on any
following TX status report.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
Link: https://msgid.link/20231219174814.2581575-1-j@w1.fi
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
include/net/mac80111.h contains a number of either excess or incorrect
kerneldoc entries for structure members, leading to these warnings:
./include/net/mac80211.h:491: warning: Excess struct member 'rssi' description in 'ieee80211_event'
./include/net/mac80211.h:491: warning: Excess struct member 'mlme' description in 'ieee80211_event'
./include/net/mac80211.h:491: warning: Excess struct member 'ba' description in 'ieee80211_event'
./include/net/mac80211.h:777: warning: Excess struct member 'ack_enabled' description in 'ieee80211_bss_conf'
./include/net/mac80211.h:1222: warning: Excess struct member 'ampdu_ack_len' description in 'ieee80211_tx_info'
./include/net/mac80211.h:1222: warning: Excess struct member 'ampdu_len' description in 'ieee80211_tx_info'
./include/net/mac80211.h:1222: warning: Excess struct member 'ack_signal' description in 'ieee80211_tx_info'
./include/net/mac80211.h:2920: warning: Excess struct member 'radiotap_he' description in 'ieee80211_hw'
Fix or remove the entries as needed. This change removes 208 warnings from
a "make htmldocs" build.
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://msgid.link/87zfy4bhxo.fsf@meer.lwn.net
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
include/net/cfg80211.h includes a number of kerneldoc entries for struct
members that do not exist, leading to these warnings:
./include/net/cfg80211.h:3192: warning: Excess struct member 'band_pref' description in 'cfg80211_bss_selection'
./include/net/cfg80211.h:3192: warning: Excess struct member 'adjust' description in 'cfg80211_bss_selection'
./include/net/cfg80211.h:6181: warning: Excess struct member 'bssid' description in 'wireless_dev'
./include/net/cfg80211.h:6181: warning: Excess struct member 'beacon_interval' description in 'wireless_dev'
./include/net/cfg80211.h:7299: warning: Excess struct member 'bss' description in 'cfg80211_rx_assoc_resp_data'
Remove and/or repair each entry to address the warnings and ensure a proper
docs build for the affected structures.
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
Reviewed-by: Randy Dunlap <rdunlap@infradead.org>
Link: https://msgid.link/87plz1g2sc.fsf@meer.lwn.net
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
There are many same functions like _rtl88e_phy_calculate_bit_shift(),
_rtl92c_phy_calculate_bit_shift() and so on. And these functions can
cause undefined bitwise shift behavior. Add calculate_bit_shift() to
replace them and fix undefined behavior in subsequent patches.
Signed-off-by: Su Hui <suhui@nfschina.com>
Acked-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://msgid.link/20231219065739.1895666-2-suhui@nfschina.com
Because some platform Bluetooth will have many background scan when idle.
And the frequently Bluetooth scan will break Wi-Fi traffic many times at
a short duration, it will make Wi-Fi throughput become lower. This patch
will shorter Bluetooth slot and adjust priority settings, make Wi-Fi can
have a more completed duration to do traffic.
Signed-off-by: Ching-Te Ku <ku920601@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://msgid.link/20231218061341.51255-12-pkshih@realtek.com
Coexistence will set the RF parameter according to Wi-Fi link mode,
Wi-Fi/Bluetooth signal level, traffic direction, antenna type,
and is there Bluetooth connection exist or not. Bluetooth will notify
the current LNA level by scoreboard. If the setting not as expected,
coexistence will try to assign the correct level.
Signed-off-by: Ching-Te Ku <ku920601@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://msgid.link/20231218061341.51255-10-pkshih@realtek.com
Including Wi-Fi RF mode to judge is Wi-Fi RF still on or off,
if Wi-Fi is RF off should set scoreboard to let Bluetooth know
Wi-Fi has gone. Every time the Wi-Fi radio state changed firmware
should force execute refresh the TDMA coexistence mechanism to
prevent incorrect mechanism runs at mismatch state. The coexistence
antenna/TDMA settings should consider what the Wi-Fi mode it is now,
this can help to solve some LPS transient state issue like A2DP
slightly glitch.
Signed-off-by: Ching-Te Ku <ku920601@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://msgid.link/20231218061341.51255-7-pkshih@realtek.com
BTG is a RF system type, it means Wi-Fi 2.4GHz and Bluetooth share RF gain
and antenna. The RF gain must control by Wi-Fi or Bluetooth in single side.
For example, if Bluetooth RX a very strong signal, then Bluetooth will
adjust to a lower gain. And Wi-Fi will also use the same gain to do RX,
then maybe the gain will not enough. This BTG control mechanism can do
some refine to this situation.
Signed-off-by: Ching-Te Ku <ku920601@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://msgid.link/20231218061341.51255-5-pkshih@realtek.com
Pre-AGC(Auto gain control) is a hardware mechanism, it will auto adjust
the RX gain for every packet, it can help to keep Wi-Fi signal on a well
RX quality. The coexistence will give advice to control the API and
monitor the settings by firmware report.
Also add function to check register, these registers were monitoring
by Wi-Fi firmware and report to coexistence driver periodically. This
can help to track whether these settings were taking effect or not.
Signed-off-by: Ching-Te Ku <ku920601@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://msgid.link/20231218061341.51255-4-pkshih@realtek.com
