On STM32MP25, OTP area may be read/written by using BSEC (boot, security
and OTP control). The BSEC internal peripheral is only managed by the
secure world.
The 12 Kbits of OTP (effective) are organized into the following regions:
- lower OTP (OTP0 to OTP127) = 4096 lower OTP bits,
bitwise (1-bit) programmable
- mid OTP (OTP128 to OTP255) = 4096 middle OTP bits,
bulk (32-bit) programmable
- upper OTP (OTP256 to OTP383) = 4096 upper OTP bits,
bulk (32-bit) programmable,
only accessible when BSEC is in closed state.
As HWKEY and ECIES key are only accessible by ROM code;
only 368 OTP words are managed in this driver (OTP0 to OTP267).
This patch adds the STM32MP25 configuration for reading and writing
the OTP data using the OP-TEE BSEC TA services.
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Link: https://lore.kernel.org/r/20231215111536.316972-11-srinivas.kandagatla@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The binary content of nvmem devices is available to the user so in the
easiest cases, finding the content of a cell is rather easy as it is
just a matter of looking at a known and fixed offset. However, nvmem
layouts have been recently introduced to cope with more advanced
situations, where the offset and size of the cells is not known in
advance or is dynamic. When using layouts, more advanced parsers are
used by the kernel in order to give direct access to the content of each
cell, regardless of its position/size in the underlying
device. Unfortunately, these information are not accessible by users,
unless by fully re-implementing the parser logic in userland.
Let's expose the cells and their content through sysfs to avoid these
situations. Of course the relevant NVMEM sysfs Kconfig option must be
enabled for this support to be available.
Not all nvmem devices expose cells. Indeed, the .bin_attrs attribute
group member will be filled at runtime only when relevant and will
remain empty otherwise. In this case, as the cells attribute group will
be empty, it will not lead to any additional folder/file creation.
Exposed cells are read-only. There is, in practice, everything in the
core to support a write path, but as I don't see any need for that, I
prefer to keep the interface simple (and probably safer). The interface
is documented as being in the "testing" state which means we can later
add a write attribute if though relevant.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Tested-by: Rafał Miłecki <rafal@milecki.pl>
Tested-by: Chen-Yu Tsai <wenst@chromium.org>
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Link: https://lore.kernel.org/r/20231215111536.316972-9-srinivas.kandagatla@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The binary content of nvmem devices is available to the user so in the
easiest cases, finding the content of a cell is rather easy as it is
just a matter of looking at a known and fixed offset. However, nvmem
layouts have been recently introduced to cope with more advanced
situations, where the offset and size of the cells is not known in
advance or is dynamic. When using layouts, more advanced parsers are
used by the kernel in order to give direct access to the content of each
cell regardless of their position/size in the underlying device, but
these information were not accessible to the user.
By exposing the nvmem cells to the user through a dedicated cell/ folder
containing one file per cell, we provide a straightforward access to
useful user information without the need for re-writing a userland
parser. Content of nvmem cells is usually: product names, manufacturing
date, MAC addresses, etc,
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Link: https://lore.kernel.org/r/20231215111536.316972-8-srinivas.kandagatla@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Current layout support was initially written without modules support in
mind. When the requirement for module support rose, the existing base
was improved to adopt modularization support, but kind of a design flaw
was introduced. With the existing implementation, when a storage device
registers into NVMEM, the core tries to hook a layout (if any) and
populates its cells immediately. This means, if the hardware description
expects a layout to be hooked up, but no driver was provided for that,
the storage medium will fail to probe and try later from
scratch. Even if we consider that the hardware description shall be
correct, we could still probe the storage device (especially if it
contains the rootfs).
One way to overcome this situation is to consider the layouts as
devices, and leverage the native notifier mechanism. When a new NVMEM
device is registered, we can populate its nvmem-layout child, if any,
and wait for the matching to be done in order to get the cells (the
waiting can be easily done with the NVMEM notifiers). If the layout
driver is compiled as a module, it should automatically be loaded. This
way, there is no strong order to enforce, any NVMEM device creation
or NVMEM layout driver insertion will be observed as a new event which
may lead to the creation of additional cells, without disturbing the
probes with costly (and sometimes endless) deferrals.
In order to achieve that goal we create a new bus for the nvmem-layouts
with minimal logic to match nvmem-layout devices with nvmem-layout
drivers. All this infrastructure code is created in the layouts.c file.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Tested-by: Rafał Miłecki <rafal@milecki.pl>
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Link: https://lore.kernel.org/r/20231215111536.316972-7-srinivas.kandagatla@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
nvmem-consumer.h is included by consumer devices, extracting data from
NVMEM devices whereas nvmem-provider.h is included by devices providing
NVMEM content.
The only users of of_nvmem_layout_get_container() outside of the core
are layout drivers, so better move its prototype to nvmem-provider.h.
While we do so, we also move the kdoc associated with the function to
the header rather than the .c file.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Link: https://lore.kernel.org/r/20231215111536.316972-3-srinivas.kandagatla@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Suzuki writes:
coresight: Updates for Linux v6.8
Updates for the hwtracing subsystem includes :
- Support for CoreSight TPDM DSB set
- Support for tuning Cycle count Threshold for CoreSight ETM via perf
- Support for TRBE on ACPI based systems
- Support for choosing buffer mode in ETR for sysfs mode
- Improvements to HiSilicon PTT driver
- Cleanups to Ultrasoc SMB driver
- Cleanup .remove callback for various Coresight platform drivers
- Remove Leo Yan from Reviewers
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
* tag 'coresight-next-v6.8' of git://git.kernel.org/pub/scm/linux/kernel/git/coresight/linux: (32 commits)
coresight: ultrasoc-smb: Use guards to cleanup
coresight: ultrasoc-smb: Convert to platform remove callback returning void
coresight: trbe: Convert to platform remove callback returning void
coresight: replicator: Convert to platform remove callback returning void
coresight: funnel: Convert to platform remove callback returning void
coresight: etm4x: Convert to platform remove callback returning void
coresight: dummy: Convert to platform remove callback returning void
coresight: etm4x: Fix width of CCITMIN field
coresight-tpdm: Correct the property name of MSR number
hwtracing: hisi_ptt: Optimize the trace data committing
hwtracing: hisi_ptt: Disable interrupt after trace end
Documentation: ABI: coresight-tpdm: Fix Bit[3] description indentation
coresight-tpdm: Add nodes for dsb msr support
dt-bindings: arm: Add support for DSB MSR register
coresight-tpdm: Add nodes for timestamp request
coresight-tpdm: Add nodes to configure pattern match output
coresight-tpdm: Add nodes for dsb edge control
coresight-tpdm: Add node to set dsb programming mode
coresight-tpdm: Add nodes to set trigger timestamp and type
coresight-tpdm: Add reset node to TPDM node
...
Pull scheduler fix from Borislav Petkov:
- Make sure tasks are thawed exactly and only once to avoid their state
getting corrupted
* tag 'sched_urgent_for_v6.7_rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
freezer,sched: Do not restore saved_state of a thawed task
Pull perf event fix from Borislav Petkov:
- Make sure perf event size validation is done on every event in the
group
* tag 'perf_urgent_for_v6.7_rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
perf: Fix perf_event_validate_size()
Pull x86 fixes from Borislav Petkov:
- Add a forgotten CPU vendor check in the AMD microcode post-loading
callback so that the callback runs only on AMD
- Make sure SEV-ES protocol negotiation happens only once and on the
BSP
* tag 'x86_urgent_for_v6.7_rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/CPU/AMD: Check vendor in the AMD microcode callback
x86/sev: Fix kernel crash due to late update to read-only ghcb_version
Pull kvm fixes from Paolo Bonzini:
"Generic:
- Set .owner for various KVM file_operations so that files refcount
the KVM module until KVM is done executing _all_ code, including
the last few instructions of kvm_put_kvm(). And then revert the
misguided attempt to rely on "struct kvm" refcounts to pin
KVM-the-module.
ARM:
- Do not redo the mapping of vLPIs, if they have already been mapped
s390:
- Do not leave bits behind in PTEs
- Properly catch page invalidations that affect the prefix of a
nested guest
x86:
- When checking if a _running_ vCPU is "in-kernel", i.e. running at
CPL0, get the CPL directly instead of relying on
preempted_in_kernel (which is valid if and only if the vCPU was
preempted, i.e. NOT running).
- Fix a benign "return void" that was recently introduced.
Selftests:
- Makefile tweak for dependency generation
- '-Wformat' fix"
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm:
KVM: SVM: Update EFER software model on CR0 trap for SEV-ES
KVM: selftests: add -MP to CFLAGS
KVM: selftests: Actually print out magic token in NX hugepages skip message
KVM: x86: Remove 'return void' expression for 'void function'
Revert "KVM: Prevent module exit until all VMs are freed"
KVM: Set file_operations.owner appropriately for all such structures
KVM: x86: Get CPL directly when checking if loaded vCPU is in kernel mode
KVM: arm64: GICv4: Do not perform a map to a mapped vLPI
KVM: s390/mm: Properly reset no-dat
KVM: s390: vsie: fix wrong VIR 37 when MSO is used
Pull powerpc fix from Michael Ellerman:
- Fix stack teardown in ftrace_no_trace, seen as crashes doing CPU
hotplug while ftrace is active.
Thanks to Naveen N Rao.
* tag 'powerpc-6.7-4' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux:
powerpc/ftrace: Fix stack teardown in ftrace_no_trace
Pull gpio fix from Bartosz Golaszewski:
- fix an error path after a failed export in sysfs code
* tag 'gpio-fixes-for-v6.7-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/brgl/linux:
gpiolib: sysfs: Fix error handling on failed export
Pull USB fixes from Greg KH:
"Here are some small USB fixes for 6.7-rc5 to resolve some reported
issues. Included in here are:
- usb gadget f_hid, and uevent fix
- xhci driver revert to resolve a much-reported issue
- typec driver fix
All of these have been in linux-next with no reported issues"
* tag 'usb-6.7-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb:
usb: gadget: f_hid: fix report descriptor allocation
Revert "xhci: Loosen RPM as default policy to cover for AMD xHC 1.1"
usb: typec: class: fix typec_altmode_put_partner to put plugs
USB: gadget: core: adjust uevent timing on gadget unbind
Pull serial driver fixes from Greg KH:
"Here are some small serial driver fixes for 6.7-rc4 to resolve some
reported issues. Included in here are:
- pl011 dma support fix
- sc16is7xx driver fix
- ma35d1 console index fix
- 8250 driver fixes for small issues
All of these have been in linux-next with no reported issues"
* tag 'tty-6.7-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty:
serial: 8250_dw: Add ACPI ID for Granite Rapids-D UART
serial: ma35d1: Validate console index before assignment
ARM: PL011: Fix DMA support
serial: sc16is7xx: address RX timeout interrupt errata
serial: 8250: 8250_omap: Clear UART_HAS_RHR_IT_DIS bit
serial: 8250_omap: Add earlycon support for the AM654 UART controller
serial: 8250: 8250_omap: Do not start RX DMA on THRI interrupt
Pull char / misc driver fixes from Greg KH:
"Here are some small fixes for 6.7-rc5 for a variety of small driver
subsystems. Included in here are:
- debugfs revert for reported issue
- greybus revert for reported issue
- greybus fixup for endian build warning
- coresight driver fixes
- nvmem driver fixes
- devcoredump fix
- parport new device id
- ndtest build fix
All of these have ben in linux-next with no reported issues"
* tag 'char-misc-6.7-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc:
nvmem: Do not expect fixed layouts to grab a layout driver
parport: Add support for Brainboxes IX/UC/PX parallel cards
Revert "greybus: gb-beagleplay: Ensure le for values in transport"
greybus: gb-beagleplay: Ensure le for values in transport
greybus: BeaglePlay driver needs CRC_CCITT
Revert "debugfs: annotate debugfs handlers vs. removal with lockdep"
devcoredump: Send uevent once devcd is ready
ndtest: fix typo class_regster -> class_register
misc: mei: client.c: fix problem of return '-EOVERFLOW' in mei_cl_write
misc: mei: client.c: return negative error code in mei_cl_write
mei: pxp: fix mei_pxp_send_message return value
coresight: ultrasoc-smb: Fix uninitialized before use buf_hw_base
coresight: ultrasoc-smb: Config SMB buffer before register sink
coresight: ultrasoc-smb: Fix sleep while close preempt in enable_smb
Documentation: coresight: fix `make refcheckdocs` warning
hwtracing: hisi_ptt: Don't try to attach a task
hwtracing: hisi_ptt: Handle the interrupt in hardirq context
hwtracing: hisi_ptt: Add dummy callback pmu::read()
coresight: Fix crash when Perf and sysfs modes are used concurrently
coresight: etm4x: Remove bogous __exit annotation for some functions
Pull LoongArch fixes from Huacai Chen:
"Preserve syscall nr across execve(), slightly clean up drdtime(), fix
the Clang built zboot kernel, fix a stack unwinder bug and several bpf
jit bugs"
* tag 'loongarch-fixes-6.7-2' of git://git.kernel.org/pub/scm/linux/kernel/git/chenhuacai/linux-loongson:
LoongArch: BPF: Fix unconditional bswap instructions
LoongArch: BPF: Fix sign-extension mov instructions
LoongArch: BPF: Don't sign extend function return value
LoongArch: BPF: Don't sign extend memory load operand
LoongArch: Preserve syscall nr across execve()
LoongArch: Set unwind stack type to unknown rather than set error flag
LoongArch: Slightly clean up drdtime()
LoongArch: Apply dynamic relocations for LLD
Pull MIPS fixes from Thomas Bogendoerfer:
- Fixes for broken Loongson firmware
- Fix lockdep splat
- Fix FPU states when creating kernel threads
* tag 'mips-fixes_6.7_1' of git://git.kernel.org/pub/scm/linux/kernel/git/mips/linux:
MIPS: kernel: Clear FPU states when setting up kernel threads
MIPS: Loongson64: Handle more memory types passed from firmware
MIPS: Loongson64: Enable DMA noncoherent support
MIPS: Loongson64: Reserve vgabios memory on boot
mips/smp: Call rcutree_report_cpu_starting() earlier
Pull perf tools fixes from Namhyung Kim:
"A random set of small bug fixes including:
- Fix segfault on AmpereOne due to missing default metricgroup name
- Fix segfault on `perf list --json` due to NULL pointer"
* tag 'perf-tools-fixes-for-v6.7-2-2023-12-08' of git://git.kernel.org/pub/scm/linux/kernel/git/perf/perf-tools:
perf list: Fix JSON segfault by setting the used skip_duplicate_pmus callback
perf vendor events arm64: AmpereOne: Add missing DefaultMetricgroupName fields
perf metrics: Avoid segv if default metricgroup isn't set
Pull smb client fixes from Steve French:
"Six smb3 client fixes:
- Fixes for copy_file_range and clone (cache invalidation and file
size), also addresses an xfstest failure
- Fix to return proper error if REMAP_FILE_DEDUP set (also fixes
xfstest generic/304)
- Fix potential null pointer reference with DFS
- Multichannel fix addressing (reverting an earlier patch) some of
the problems with enabling/disabling channels dynamically
Still working on a followon multichannel fix to address another issue
found in reconnect testing that will send next week"
* tag '6.7-rc4-smb3-client-fixes' of git://git.samba.org/sfrench/cifs-2.6:
cifs: reconnect worker should take reference on server struct unconditionally
Revert "cifs: reconnect work should have reference on server struct"
cifs: Fix non-availability of dedup breaking generic/304
smb: client: fix potential NULL deref in parse_dfs_referrals()
cifs: Fix flushing, invalidation and file size with FICLONE
cifs: Fix flushing, invalidation and file size with copy_file_range()
We can see that "bswap32: Takes an unsigned 32-bit number in either big-
or little-endian format and returns the equivalent number with the same
bit width but opposite endianness" in BPF Instruction Set Specification,
so it should clear the upper 32 bits in "case 32:" for both BPF_ALU and
BPF_ALU64.
[root@linux fedora]# echo 1 > /proc/sys/net/core/bpf_jit_enable
[root@linux fedora]# modprobe test_bpf
Before:
test_bpf: #313 BSWAP 32: 0x0123456789abcdef -> 0xefcdab89 jited:1 ret 1460850314 != -271733879 (0x5712ce8a != 0xefcdab89)FAIL (1 times)
test_bpf: #317 BSWAP 32: 0xfedcba9876543210 -> 0x10325476 jited:1 ret -1460850316 != 271733878 (0xa8ed3174 != 0x10325476)FAIL (1 times)
After:
test_bpf: #313 BSWAP 32: 0x0123456789abcdef -> 0xefcdab89 jited:1 4 PASS
test_bpf: #317 BSWAP 32: 0xfedcba9876543210 -> 0x10325476 jited:1 4 PASS
Fixes: 4ebf9216e7 ("LoongArch: BPF: Support unconditional bswap instructions")
Acked-by: Hengqi Chen <hengqi.chen@gmail.com>
Signed-off-by: Tiezhu Yang <yangtiezhu@loongson.cn>
Signed-off-by: Huacai Chen <chenhuacai@loongson.cn>
We can see that "Short form of movsx, dst_reg = (s8,s16,s32)src_reg" in
include/linux/filter.h, additionally, for BPF_ALU64 the value of the
destination register is unchanged whereas for BPF_ALU the upper 32 bits
of the destination register are zeroed, so it should clear the upper 32
bits for BPF_ALU.
[root@linux fedora]# echo 1 > /proc/sys/net/core/bpf_jit_enable
[root@linux fedora]# modprobe test_bpf
Before:
test_bpf: #81 ALU_MOVSX | BPF_B jited:1 ret 2 != 1 (0x2 != 0x1)FAIL (1 times)
test_bpf: #82 ALU_MOVSX | BPF_H jited:1 ret 2 != 1 (0x2 != 0x1)FAIL (1 times)
After:
test_bpf: #81 ALU_MOVSX | BPF_B jited:1 6 PASS
test_bpf: #82 ALU_MOVSX | BPF_H jited:1 6 PASS
By the way, the bpf selftest case "./test_progs -t verifier_movsx" can
also be fixed with this patch.
Fixes: f48012f161 ("LoongArch: BPF: Support sign-extension mov instructions")
Acked-by: Hengqi Chen <hengqi.chen@gmail.com>
Signed-off-by: Tiezhu Yang <yangtiezhu@loongson.cn>
Signed-off-by: Huacai Chen <chenhuacai@loongson.cn>
Currently, we store syscall nr in pt_regs::regs[11] and syscall execve()
accidentally overrides it during its execution:
sys_execve()
-> do_execve()
-> do_execveat_common()
-> bprm_execve()
-> exec_binprm()
-> search_binary_handler()
-> load_elf_binary()
-> ELF_PLAT_INIT()
ELF_PLAT_INIT() reset regs[11] to 0, so in syscall_exit_to_user_mode()
we later get a wrong syscall nr. This breaks tools like execsnoop since
it relies on execve() tracepoints.
Skip pt_regs::regs[11] reset in ELF_PLAT_INIT() to fix the issue.
Signed-off-by: Hengqi Chen <hengqi.chen@gmail.com>
Signed-off-by: Huacai Chen <chenhuacai@loongson.cn>
During unwinding, unwind_done() is used as an end condition. Normally it
unwind to the user stack and then set the stack type to unknown, which
is a normal exit. When something unexpected happens in unwind process
and we cannot unwind anymore, we should set the error flag, and also set
the stack type to unknown to indicate that the unwind process can not
continue. The error flag emphasizes that the unwind process produce an
unexpected error. There is no unexpected things when we unwind the PT_REGS
in the top of IRQ stack and find out that is an user mode PT_REGS. Thus,
we should not set error flag and just set stack type to unknown.
Reported-by: Hengqi Chen <hengqi.chen@gmail.com>
Acked-by: Hengqi Chen <hengqi.chen@gmail.com>
Signed-off-by: Jinyang He <hejinyang@loongson.cn>
Signed-off-by: Huacai Chen <chenhuacai@loongson.cn>
As we are just discarding the stable clock ID, simply write it into
$zero instead of allocating a temporary register.
Signed-off-by: Xi Ruoyao <xry111@xry111.site>
Signed-off-by: Huacai Chen <chenhuacai@loongson.cn>
For the following assembly code:
.text
.global func
func:
nop
.data
var:
.dword func
When linked with `-pie`, GNU LD populates the `var` variable with the
pre-relocated value of `func`. However, LLVM LLD does not exhibit the
same behavior. This issue also arises with the `kernel_entry` in arch/
loongarch/kernel/head.S:
_head:
.word MZ_MAGIC /* "MZ", MS-DOS header */
.org 0x8
.dword kernel_entry /* Kernel entry point */
The correct kernel entry from the MS-DOS header is crucial for jumping
to vmlinux from zboot. This necessity is why the compressed relocatable
kernel compiled by Clang encounters difficulties in booting.
To address this problem, it is proposed to apply dynamic relocations to
place with `--apply-dynamic-relocs`.
Link: https://github.com/ClangBuiltLinux/linux/issues/1962
Signed-off-by: WANG Rui <wangrui@loongson.cn>
Signed-off-by: Huacai Chen <chenhuacai@loongson.cn>
Pull SCSI fix from James Bottomley:
"One tiny fix to the be2iscsi driver fixing a memory leak in an error
leg"
* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
scsi: be2iscsi: Fix a memleak in beiscsi_init_wrb_handle()
Pull block fixes from Jens Axboe:
"Nothing major in here, just miscellanous fixes for MD and NVMe:
- NVMe pull request via Keith:
- Proper nvme ctrl state setting (Keith)
- Passthrough command optimization (Keith)
- Spectre fix (Nitesh)
- Kconfig clarifications (Shin'ichiro)
- Frozen state deadlock fix (Bitao)
- Power setting quirk (Georg)
- MD pull requests via Song:
- 6.7 regresisons with recovery/sync (Yu)
- Reshape fix (David)"
* tag 'block-6.7-2023-12-08' of git://git.kernel.dk/linux:
md: split MD_RECOVERY_NEEDED out of mddev_resume
nvme-pci: Add sleep quirk for Kingston drives
md: fix stopping sync thread
md: don't leave 'MD_RECOVERY_FROZEN' in error path of md_set_readonly()
md: fix missing flush of sync_work
nvme: fix deadlock between reset and scan
nvme: prevent potential spectre v1 gadget
nvme: improve NVME_HOST_AUTH and NVME_TARGET_AUTH config descriptions
nvme-ioctl: move capable() admin check to the end
nvme: ensure reset state check ordering
nvme: introduce helper function to get ctrl state
md/raid6: use valid sector values to determine if an I/O should wait on the reshape
Pull io_uring fixes from Jens Axboe:
"Two minor fixes for issues introduced in this release cycle, and two
fixes for issues or potential issues that are heading to stable.
One of these ends up disabling passing io_uring file descriptors via
SCM_RIGHTS. There really shouldn't be an overlap between that kind of
historic use case and modern usage of io_uring, which is why this was
deemed appropriate"
* tag 'io_uring-6.7-2023-12-08' of git://git.kernel.dk/linux:
io_uring/af_unix: disable sending io_uring over sockets
io_uring/kbuf: check for buffer list readiness after NULL check
io_uring/kbuf: Fix an NULL vs IS_ERR() bug in io_alloc_pbuf_ring()
io_uring: fix mutex_unlock with unreferenced ctx
Pull rdma fixes from Jason Gunthorpe:
"Primarily rtrs and irdma fixes:
- Fix uninitialized value in ib_get_eth_speed()
- Fix hns refusing to work if userspace doesn't select the correct
congestion control algorithm
- Several irdma fixes - unreliable Send Queue Drain, use after free,
64k page size bugs, device removal races
- Several rtrs bug fixes - crashes, memory leaks, use after free, bad
credit accounting, bogus WARN_ON
- Typos and a MAINTAINER update"
* tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rdma/rdma:
RDMA/irdma: Avoid free the non-cqp_request scratch
RDMA/irdma: Fix support for 64k pages
RDMA/irdma: Ensure iWarp QP queue memory is OS paged aligned
RDMA/core: Fix umem iterator when PAGE_SIZE is greater then HCA pgsz
RDMA/irdma: Fix UAF in irdma_sc_ccq_get_cqe_info()
RDMA/bnxt_re: Correct module description string
RDMA/rtrs-clt: Remove the warnings for req in_use check
RDMA/rtrs-clt: Fix the max_send_wr setting
RDMA/rtrs-srv: Destroy path files after making sure no IOs in-flight
RDMA/rtrs-srv: Free srv_mr iu only when always_invalidate is true
RDMA/rtrs-srv: Check return values while processing info request
RDMA/rtrs-clt: Start hb after path_up
RDMA/rtrs-srv: Do not unconditionally enable irq
MAINTAINERS: Add Chengchang Tang as Hisilicon RoCE maintainer
RDMA/irdma: Add wait for suspend on SQD
RDMA/irdma: Do not modify to SQD on error
RDMA/hns: Fix unnecessary err return when using invalid congest control algorithm
RDMA/core: Fix uninit-value access in ib_get_eth_speed()
Pull power management fix from Rafael Wysocki:
"Fix cpufreq reference counting in the DTPM (dynamic thermal and power
management) power capping framework (Lukasz Luba)"
* tag 'pm-6.7-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
powercap: DTPM: Fix missing cpufreq_cpu_put() calls
Pull ACPI fix from Rafael Wysocki:
"Fix a possible crash on an attempt to free unallocated memory in the
error path of acpi_evaluate_reference() that has been introduced by
one of the recent changes (Rafael Wysocki)"
* tag 'acpi-6.7-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
ACPI: utils: Fix error path in acpi_evaluate_reference()
Pull hwmon fixes from Guenter Roeck:
- acpi_power_meter: Fix 4.29 MW output seen if acpi reports bad data
- corsair-psu: Fix ability to probe if the driver is built into the kernel
- ltc2991: Fix spelling mistake "contiuous" -> "continuous"
- max31827: Add missing regulator header file include
- nzxt-kraken2: Fix error handling path in probe function
* tag 'hwmon-for-v6.7-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging:
hwmon: (corsair-psu) Fix probe when built-in
hwmon: (nzxt-kraken2) Fix error handling path in kraken2_probe()
hwmon: (acpi_power_meter) Fix 4.29 MW bug
hwmon: max31827: include regulator header
hwmon: ltc2991: Fix spelling mistake "contiuous" -> "continuous"
Pull pwm fix from Uwe Kleine-König:
"This fixes a null pointer exception in the bcm2835 pwm driver.
The problem was introduced by a combination of two commits merged for
v6.7-rc1 where each change alone would have been fine.
Thanks to Florian Fainelli for noticing and fixing the issue"
* tag 'pwm/for-6.7-rc5-fixes' of https://git.pengutronix.de/git/ukl/linux:
pwm: bcm2835: Fix NPD in suspend/resume
Pull sound fixes from Takashi Iwai:
"This is a typical bump in the middle of its way; we've gathered lots
of fixes (mostly for ASoC) at this time:
- PCM array out-of-bound access fix
- Correction of SOC PCM merge error
- Lots of ASoC SOF Intel updates
- A few ASoC AMD quirks
- More proper timer handling in PCM test module
- HD-audio and USB-audio quirks as usual
- Other device-specific fixes for various ASoC codecs"
* tag 'sound-6.7-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound: (39 commits)
ALSA: hda/realtek: Add quirk for Lenovo Yoga Pro 7
ALSA: pcmtest: stop timer before buffer is released
ALSA: hda/realtek: Add Framework laptop 16 to quirks
ALSA: hda/realtek: add new Framework laptop to quirks
ALSA: pcm: fix out-of-bounds in snd_pcm_state_names
ASoC: qcom: sc8280xp: Limit speaker digital volumes
ASoC: ops: add correct range check for limiting volume
ALSA: hda/realtek: Enable headset on Lenovo M90 Gen5
ALSA: hda/realtek: fix speakers on XPS 9530 (2023)
ALSA: usb-audio: Add Pioneer DJM-450 mixer controls
ASoC: wm_adsp: fix memleak in wm_adsp_buffer_populate
ASoC: da7219: Support low DC impedance headset
ASoC: amd: acp: Add support for a new Huawei Matebook laptop
ALSA: hda/realtek: Apply quirk for ASUS UM3504DA
ASoC: SOF: ipc4-topology: Correct data structures for the GAIN module
ASoC: SOF: ipc4-topology: Correct data structures for the SRC module
ASoC: hdac_hda: Conditionally register dais for HDMI and Analog
ASoC: codecs: lpass-tx-macro: set active_decimator correct default value
ASoC: amd: yc: Fix non-functional mic on ASUS E1504FA
ASoC: amd: yc: Add DMI entry to support System76 Pangolin 13
...
Pull drm fixes from Dave Airlie:
"Regular weekly fixes, mostly amdgpu and i915 as usual. A couple of
nouveau, panfrost, one core and one bridge Kconfig.
Seems about normal for rc5.
atomic-helpers:
- invoke end_fb_access while owning plane state
i915:
- fix a missing dep for a previous fix
- Relax BXT/GLK DSI transcoder hblank limits
- Fix DP MST .mode_valid_ctx() return values
- Reject DP MST modes that require bigjoiner (as it's not yet
supported on DP MST)
- Fix _intel_dsb_commit() variable type to allow negative values
nouveau:
- document some bits of gsp rm
- flush vmm more on tu102 to avoid hangs
panfrost:
- fix imported dma-buf objects residency
- fix device freq update
bridge:
- tc358768 - fix Kconfig
amdgpu:
- Disable MCBP on gfx9
- DC vbios fix
- eDP fix
- dml2 UBSAN fix
- SMU 14 fix
- RAS fixes
- dml KASAN/KCSAN fix
- PSP 13 fix
- Clockgating fixes
- Suspend fix
exynos:
- fix pointer dereference
- fix wrong error check"
* tag 'drm-fixes-2023-12-08' of git://anongit.freedesktop.org/drm/drm: (27 commits)
drm/exynos: fix a wrong error checking
drm/exynos: fix a potential error pointer dereference
drm/amdgpu: fix buffer funcs setting order on suspend
drm/amdgpu: Avoid querying DRM MGCG status
drm/amdgpu: Update HDP 4.4.2 clock gating flags
drm/amdgpu: Add NULL checks for function pointers
drm/amdgpu: Restrict extended wait to PSP v13.0.6
drm/amd/display: Increase frame warning limit with KASAN or KCSAN in dml
drm/amdgpu: optimize the printing order of error data
drm/amdgpu: Update fw version for boot time error query
drm/amd/pm: support new mca smu error code decoding
drm/amd/swsmu: update smu v14_0_0 driver if version and metrics table
drm/amd/display: Fix array-index-out-of-bounds in dml2
drm/amd/display: Add monitor patch for specific eDP
drm/amd/display: Use channel_width = 2 for vram table 3.0
drm/amdgpu: disable MCBP by default
drm/atomic-helpers: Invoke end_fb_access while owning plane state
drm/i915: correct the input parameter on _intel_dsb_commit()
drm/i915/mst: Reject modes that require the bigjoiner
drm/i915/mst: Fix .mode_valid_ctx() return values
...
In general, activating long mode involves setting the EFER_LME bit in
the EFER register and then enabling the X86_CR0_PG bit in the CR0
register. At this point, the EFER_LMA bit will be set automatically by
hardware.
In the case of SVM/SEV guests where writes to CR0 are intercepted, it's
necessary for the host to set EFER_LMA on behalf of the guest since
hardware does not see the actual CR0 write.
In the case of SEV-ES guests where writes to CR0 are trapped instead of
intercepted, the hardware *does* see/record the write to CR0 before
exiting and passing the value on to the host, so as part of enabling
SEV-ES support commit f1c6366e30 ("KVM: SVM: Add required changes to
support intercepts under SEV-ES") dropped special handling of the
EFER_LMA bit with the understanding that it would be set automatically.
However, since the guest never explicitly sets the EFER_LMA bit, the
host never becomes aware that it has been set. This becomes problematic
when userspace tries to get/set the EFER values via
KVM_GET_SREGS/KVM_SET_SREGS, since the EFER contents tracked by the host
will be missing the EFER_LMA bit, and when userspace attempts to pass
the EFER value back via KVM_SET_SREGS it will fail a sanity check that
asserts that EFER_LMA should always be set when X86_CR0_PG and EFER_LME
are set.
Fix this by always inferring the value of EFER_LMA based on X86_CR0_PG
and EFER_LME, regardless of whether or not SEV-ES is enabled.
Fixes: f1c6366e30 ("KVM: SVM: Add required changes to support intercepts under SEV-ES")
Reported-by: Peter Gonda <pgonda@google.com>
Cc: stable@vger.kernel.org
Signed-off-by: Sean Christopherson <seanjc@google.com>
Message-Id: <20210507165947.2502412-2-seanjc@google.com>
[A two year old patch that was revived after we noticed the failure in
KVM_SET_SREGS and a similar patch was posted by Michael Roth. This is
Sean's patch, but with Michael's more complete commit message. - Paolo]
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
It seems that when the driver is built-in, the HID bus is
initialized after the driver is loaded, which whould cause
module_hid_driver() to fail.
Fix this by registering the driver after the HID bus using
late_initcall() in accordance with other hwmon HID drivers.
Signed-off-by: Armin Wolf <W_Armin@gmx.de>
Link: https://lore.kernel.org/r/20231207210723.222552-1-W_Armin@gmx.de
[groeck: Dropped "compile tested" comment; the patch has been tested
but the tester did not provide a Tested-by: tag]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Pass MAGIC_TOKEN to __TEST_REQUIRE() when printing the help message about
needing to pass a magic value to manually run the NX hugepages test,
otherwise the help message will contain garbage.
In file included from x86_64/nx_huge_pages_test.c:15:
x86_64/nx_huge_pages_test.c: In function ‘main’:
include/test_util.h:40:32: error: format ‘%d’ expects a matching ‘int’ argument [-Werror=format=]
40 | ksft_exit_skip("- " fmt "\n", ##__VA_ARGS__); \
| ^~~~
x86_64/nx_huge_pages_test.c:259:9: note: in expansion of macro ‘__TEST_REQUIRE’
259 | __TEST_REQUIRE(token == MAGIC_TOKEN,
| ^~~~~~~~~~~~~~
Signed-off-by: angquan yu <angquan21@gmail.com>
Link: https://lore.kernel.org/r/20231128221105.63093-1-angquan21@gmail.com
[sean: rewrite shortlog+changelog]
Signed-off-by: Sean Christopherson <seanjc@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
