Over the time, the SCM and MSS driver were refactored to use
SoC-specific compatibles. While the generic compatibles still work
correctly, add the MSM8916-specific compatibles so they are actually
used somewhere.
For SCM this will ensure that we actually manage to obtain all
three of the specified clocks, since those are required on MSM8916.
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Link: https://lore.kernel.org/r/20200915071221.72895-9-stephan@gerhold.net
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
The hwlock device node does not (directly) use memory resources
of the SoC, so we should move it outside the "soc" node.
However, as of commit 7a1e6fb1c6 ("hwspinlock: qcom: Allow mmio usage
in addition to syscon") we can now assign the memory region directly
to the hwlock device node. This works because the register space
used by it is actually separate and not used by any other components.
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Link: https://lore.kernel.org/r/20200915071221.72895-7-stephan@gerhold.net
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
dt-bindings/interrupt-controller/arm-gic.h has a GIC_SPI define
that allows specifying interrupts more clearly, but right now only
some device nodes in msm8916.dtsi make use of it.
Convert all others to use it.
The same applies to the IRQ_TYPE_* defines in
dt-bindings/interrupt-controller/irq.h. Some interrupts were defined
with raw numbers, or even with IRQ_TYPE_NONE (0).
Convert all these to use appropriate IRQ types.
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Link: https://lore.kernel.org/r/20200915071221.72895-6-stephan@gerhold.net
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
The mdss node sets #interrupt-cells = <1>, so its interrupts
should be referenced using a single cell (in this case: only the
interrupt number).
However, right now the mdp/dsi node both have two interrupt cells
set, e.g. interrupts = <4 0>. The 0 is probably meant to say
IRQ_TYPE_NONE (= 0), but with #interrupt-cells = <1> this is
actually interpreted as a second interrupt line.
Remove the IRQ flags from both interrupts to fix this.
Fixes: 305410ffd1 ("arm64: dts: msm8916: Add display support")
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Link: https://lore.kernel.org/r/20200915071221.72895-5-stephan@gerhold.net
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Tha parent node of "wcd_codec" specifies #address-cells = <1>
and #size-cells = <0>, which means that each resource should be
described by one cell for the address and size omitted.
However, wcd_codec currently lists 0x200 as second cell (probably
the size of the resource). When parsing this would be treated like
another memory resource - which is entirely wrong.
To quote the device tree specification [1]:
"If the parent node specifies a value of 0 for #size-cells,
the length field in the value of reg shall be omitted."
[1]: https://www.devicetree.org/specifications/
Fixes: 5582fcb382 ("arm64: dts: apq8016-sbc: add analog audio support with multicodec")
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Link: https://lore.kernel.org/r/20200915071221.72895-4-stephan@gerhold.net
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Commit fe2aff0c57 ("arm64: dts: qcom: msm8916: remove unit name for thermal trip points")
removed the unit names for most of the thermal trip points defined
in msm8916.dtsi, but missed to update the one for cpu0_1-thermal.
So why wasn't this spotted by "make dtbs_check"? Apparently, the name
of the thermal zone is already invalid: thermal-zones.yaml specifies
a regex of ^[a-zA-Z][a-zA-Z0-9\\-]{1,12}-thermal$, so it is not allowed
to contain underscores. Therefore the thermal zone was never verified
using the DTB schema.
After replacing the underscore in the thermal zone name, the warning
shows up:
apq8016-sbc.dt.yaml: thermal-zones: cpu0-1-thermal:trips: 'trip-point@0'
does not match any of the regexes: '^[a-zA-Z][a-zA-Z0-9\\-_]{0,63}$', 'pinctrl-[0-9]+'
Fix up the thermal zone names and remove the unit name for the trip point.
Cc: Amit Kucheria <amit.kucheria@linaro.org>
Fixes: fe2aff0c57 ("arm64: dts: qcom: msm8916: remove unit name for thermal trip points")
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Link: https://lore.kernel.org/r/20200915071221.72895-3-stephan@gerhold.net
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Right now we define "hnp-disable", "srp-disable", "adp-disable"
separately for every MSM8916 board that has USB working.
They are needed for USB to work properly if CONFIG_USB_OTG_FSM
is enabled. This is because the chipidea OTG FSM code waits for
interrupts regarding the VBUS state (AVVIS). Those never happen
on MSM8916 because VBUS is always connected to the PMIC instead
of the USB controller.
There was a patch [1] to work around this but ultimately it was
decided that it's easier to disable the OTG FSM altogether using
these properties. This works fine for most use cases, because the
OTG FSM isn't needed for simple dual role host/gadget operation.
Given that these properties are needed for every MSM8916 device,
move them to msm8916.dtsi so we can avoid some more duplication.
[1]: https://lore.kernel.org/lkml/20160707222114.1673-10-stephen.boyd@linaro.org/
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Link: https://lore.kernel.org/r/20200720085406.6716-11-stephan@gerhold.net
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Right now some device nodes set default pinctrl within msm8916.dtsi
(e.g. I2C, SPI), but for others it needs to be explicitly set in the
board-specific device tree (e.g. UART).
While it is theoretically possible that some super special board
needs different pinctrl for these, in practice pretty much every
board ends up using the common pinctrl definitions.
Make this consistent by also defining the common pinctrl properties
for blsp1_uart1 and blsp1_uart2 so we don't need to copy this for every
board. If there is really such a super special board it could just
override these properties with custom pinctrl or make minor modifications
to the common pinctrl configurations provided by msm8916-pins.dtsi.
Also move #address-cells/#size-cells for &dsi0 to msm8916.dtsi
since this is specific to the DSI node, not the board.
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Link: https://lore.kernel.org/r/20200720085406.6716-10-stephan@gerhold.net
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
So far we had some supplies defined for all boards in msm8916.dtsi,
while others were duplicated into every board-specific device tree.
Now that we have msm8916-pm8916.dtsi as a common include for all
standard MSM8916 devices using PM8916, move the remaining common
supplies to msm8916-pm8916.dtsi to reduce duplication a bit.
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Link: https://lore.kernel.org/r/20200720085406.6716-9-stephan@gerhold.net
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Device trees for newer SoCs avoid defining the regulator nodes directly
in the SoC device tree (here: msm8916.dtsi). The reason for this is that
theoretically it is possible to combine the SoC with a different PMIC,
or to use all the regulators in a board-specific way.
Therefore let's remove those from the SoC include (msm8916.dtsi).
In practice, pretty much all MSM8916 boards were combined with PM8916,
and use the regulators in similar ways. After looking at many different
MSM8916 boards (mostly smartphones and tablets), I haven't seen a single
device that isn't using the same regulators for components integrated
into the SoC.
If all boards end up defining all regulators and supplies in the same way
then it is useful to have an include for that, so we can avoid duplicating
it everywhere. If there is really a super special board that does it
differently it could just override some properties or avoid using the
include altogether.
This patch moves the regulator and common supply definitions to
a new include called "msm8916-pm8916.dtsi".
This is also going to be useful when introducing CPR (Core Power
Reduction) later because we can configure the CPU regulator
(pm8916_spmi_s2) for all devices in this common include.
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Link: https://lore.kernel.org/r/20200720085406.6716-8-stephan@gerhold.net
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Right now we define the entire pm8916 resin node separately in
the board-specific device tree part, including the interrupt that
belongs to PM8916.
As a feature of the PMIC it should be declared in pm8916.dtsi,
disabled by default. Like all other optional components it can then
by enabled and configured in the board-specific device tree part.
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Link: https://lore.kernel.org/r/20200720085406.6716-7-stephan@gerhold.net
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Device trees for newer SoCs avoid replicating the entire device
hierarchy in the board-specific device tree part. Instead,
they set additional properties only by referencing labels,
sorted alphabetically.
Now that we have labels for all relevant nodes, convert the MSM8916
board device trees to use the same style and remove the "soc" node
entirely.
Note: There is a large block of coresight nodes in apq8016-sbc.dtsi,
which are enabled by setting status = "okay". I kept them grouped
together (not alphabetically sorted with everything else),
since that would be just unnecessarily verbose and hard to see.
This commit only moves all existing properties to nodes that reference
the respective label. The resulting binary DTBs are exactly the same.
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Link: https://lore.kernel.org/r/20200720085406.6716-6-stephan@gerhold.net
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Add a few more labels to device nodes declared in msm8916.dtsi
so that we can set all needed properties using labels in the
board-specific device tree part.
Also rename the "otg" label to "usb" to allow grouping it with
the USB PHY (usb_hs_phy) node when ordering referenced labels
alphabetically.
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Link: https://lore.kernel.org/r/20200720085406.6716-5-stephan@gerhold.net
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
The "sound" node in apq8016-sbc.dtsi references memory regions
provided by the SoC and should be therefore declared in msm8916.dtsi.
Additionally, the machine driver used for the "qcom,apq8016-sbc-sndcard"
compatible also works on other MSM8916 devices (provided that audio
routing is set up properly). It is not really specific to apq8016-sbc.
Simplify setting up sound on other boards by moving the common part
to msm8916.dtsi. This also allows referencing the node by the label,
so that we can eventually drop the "soc" node entirely from the
board-specific device tree part and use labels exclusively.
Cc: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Link: https://lore.kernel.org/r/20200720085406.6716-3-stephan@gerhold.net
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Add initial dts support for Xiaomi Poco F1 (Beryllium).
This initial support is based on upstream Dragonboard 845c
(sdm845) device. With this dts, Beryllium boots AOSP up to
ADB shell over USB-C.
Supported functionality includes UFS, USB-C (peripheral),
microSD card and Vol+/Vol-/power keys. Bluetooth should work
too but couldn't be verified from adb command line, it is
verified when enabled from UI with few WIP display patches.
Just like initial db845c support, initializing the SMMU is
clearing the mapping used for the splash screen framebuffer,
which causes the device to hang during boot and recovery
needs a hard power reset. This can be worked around using:
fastboot oem select-display-panel none
To switch ON the display back run:
fastboot oem select-display-panel
But this only works on Beryllium devices running bootloader
version BOOT.XF.2.0-00369-SDM845LZB-1 that shipped with
Android-9 based release. Newer bootloader version do not
support switching OFF the display panel at all.
Reviewed-by: Konrad Dybcio <konradybcio@gmail.com>
Signed-off-by: Amit Pundir <amit.pundir@linaro.org>
Link: https://lore.kernel.org/r/1599840940-18144-1-git-send-email-amit.pundir@linaro.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
