The hibernation feature enabled for Xilinx Versal NET SoC in DWC3 IP.
As the DWC3 IP supports the hibernation feature, to handle the wakeup
or hibernation interrupt, add host mode "wakeup" interrupt-names
optional property in the binding schema to capture remote-wakeup and
connect/ disconnect event in the hibernation state and increased maxItems
to 4 for the interrupts and interrupt-names property.
We have a dedicated IRQ line specifically for the hibernation feature.
When the "wakeup" IRQ line is triggered, it initiates a hibernation
interrupt, causing the system to wake up from the hibernation state.
Signed-off-by: Piyush Mehta <piyush.mehta@amd.com>
Acked-by: Conor Dooley <conor.dooley@microchip.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20230619105032.2888128-1-piyush.mehta@amd.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add support for the ON Semiconductor NB7VPQ904M Type-C USB SuperSpeed
and DisplayPort ALT Mode Linear Redriver chip found on some devices
with a Type-C port.
The redriver compensates ultra High-Speeed DisplayPort and USB
Super Speed signal integrity losses mainly due to PCB & transmission
cables.
The redriver doesn't support SuperSpeed lines swapping, but
can support Type-C SBU lines swapping.
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Message-ID: <20230601-topic-sm8x50-upstream-redriver-v4-2-91d5820f3a03@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
For some reason the include/uapi/linux/usb/ directory is missing in the
USB SUBSYSTEM entry, so get_maintainer will not know to cc: the proper
mailing lists. Fix this up by adding an entry for this directory.
Message-ID: <20230615094306.2072827-2-gregkh@linuxfoundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
USB PHY DPDM wakeup bit is enabled by default, when USB wakeup
is not required(/sys/.../wakeup is disabled), this bit should be
disabled, otherwise we will have unexpected wakeup if do USB device
connect/disconnect while system sleep.
This bit can be enabled for both host and device mode.
Signed-off-by: Li Jun <jun.li@nxp.com>
Signed-off-by: Xu Yang <xu.yang_2@nxp.com>
Acked-by: Peter Chen <peter.chen@kernel.org>
Message-ID: <20230517081907.3410465-3-xu.yang_2@nxp.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
As we use bvalid for vbus wakeup source, to save power when
suspend, turn off the vbus comparator for imx7d and imx8mm.
Below is this bit description from RM of iMX8MM
"VBUS Valid Comparator Enable:
This signal controls the USB OTG PHY VBUS Valid comparator which
indicates whether the voltage on the USB_OTG*_VBUS pin is below
the VBUS Valid threshold. The VBUS Valid threshold is nominally
4.75V on this USB PHY. The VBUS Valid threshold can be adjusted
using the USBNC_OTGn_PHY_CFG1[OTGTUNE0] bit field. Status of the
VBUS Valid comparator, when it is enabled, is reported on the
USBNC_OTGn_PHY_STATUS[VBUS_VLD] bit.
When OTGDISABLE0 (USBNC_USB_OTGx_PHY_CFG2[10])is set to 1'b0 and
DRVVBUS0 is set to 1'b1, the Bandgap circuitry and VBUS Valid
comparator are powered, even in Suspend or Sleep mode.
DRVVBUS0 should be reset to 1'b0 when the internal VBUS Valid comparator
is not required, to reduce quiescent current in Suspend or Sleep mode.
- 0 The VBUS Valid comparator is disabled
- 1 The VBUS Valid comparator is enabled"
Signed-off-by: Li Jun <jun.li@nxp.com>
Signed-off-by: Xu Yang <xu.yang_2@nxp.com>
Acked-by: Peter Chen <peter.chen@kernel.org>
Message-ID: <20230517081907.3410465-2-xu.yang_2@nxp.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch introduces the main part of Cadence USBHS driver
to Linux kernel.
To reduce the patch size a little bit, the header file gadget.h was
intentionally added as separate patch.
The Cadence USB 2.0 Controller is a highly configurable IP Core which
supports both full and high speed data transfer.
The current driver has been validated with FPGA platform. We have
support for PCIe bus, which is used on FPGA prototyping.
Signed-off-by: Pawel Laszczak <pawell@cadence.com>
Message-ID: <20230602102644.77470-3-pawell@cadence.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Expose usb device state to userland as the information is useful in
detecting non-compliant setups and diagnosing enumeration failures.
For example:
- End-to-end signal integrity issues: the device would fail port reset
repeatedly and thus be stuck in POWERED state.
- Charge-only cables (missing D+/D- lines): the device would never enter
POWERED state as the HC would not see any pullup.
What's the status quo?
We do have error logs such as "Cannot enable. Maybe the USB cable is bad?"
to flag potential setup issues, but there's no good way to expose them to
userspace.
Why add a sysfs entry in struct usb_port instead of struct usb_device?
The struct usb_device is not device_add() to the system until it's in
ADDRESS state hence we would miss the first two states. The struct
usb_port is a better place to keep the information because its life
cycle is longer than the struct usb_device that is attached to the port.
Reported-by: kernel test robot <oliver.sang@intel.com>
Closes: https://lore.kernel.org/oe-lkp/202306042228.e532af6e-oliver.sang@intel.com
Reviewed-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Roy Luo <royluo@google.com>
Message-ID: <20230608015913.1679984-1-royluo@google.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Currently if we bootup a device without cable connected, then
usb-conn-gpio won't call set_role() since last_role is same as
current role. This happens because during probe last_role gets
initialised to zero.
To avoid this, added a new constant in enum usb_role, last_role
is set to USB_ROLE_UNKNOWN before performing initial detection.
While at it, also handle default case for the usb_role switch
in cdns3, intel-xhci-usb-role-switch & musb/jz4740 to avoid
build warnings.
Fixes: 4602f3bff2 ("usb: common: add USB GPIO based connection detection driver")
Signed-off-by: Prashanth K <quic_prashk@quicinc.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Message-ID: <1685544074-17337-1-git-send-email-quic_prashk@quicinc.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The fsg_lun_is_open() test can be eliminated and the code merged with
the preceding conditional, because the LUN won't be open if
cfg->filename wasn't set. Similarly, the error_lun label will never be
reached with an open lun (non-null filp) so remove the unnecessary
fsg_lun_close() call.
Signed-off-by: David Disseldorp <ddiss@suse.de>
Reviewed-by: Alan Stern <stern@rowland.harvard.edu>
Message-ID: <20230607215401.22563-1-ddiss@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If gs_close has cleared port->port.tty and gs_start_io is called
afterwards, then the function tty_wakeup will attempt to access the value
of the pointer port->port.tty which will cause a null pointer
dereference error.
To avoid this, add a null pointer check to gs_start_io before attempting
to access the value of the pointer port->port.tty.
Signed-off-by: Kuen-Han Tsai <khtsai@google.com>
Message-ID: <20230602070009.1353946-1-khtsai@google.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Trying to keep track of free trbs in a ring by adding and subtracting
deltas each time a enqueue or dequeue is increased or moved has proven to
be buggy and complicated, especially over long periods of time.
Recently a bug in counting free trbs was fixed, now taking into account
cancelled URBs that were turned into no-ops, preventing free_trbs to
slowly wander off causing unnecessary ring expansion. See
commit fe82f16aaf ("xhci: Fix incorrect tracking of free space on
transfer rings")
Turns out its a lot easier to just calculate the numer of free TRB
based on ring size and the current enqueue and dequeue pointer values.
This is currently only needed for the command ring as multi segment
transfer rings already ensures there is enough room the ring during
the ring expansion check.
We could get rid of the ring->num_trbs_free entry completely, but as
the xhci DbC code also uses it we don't clean that up in this patch.
Reported-by: Miller Hunter <MillerH@hearthnhome.com>
Closes: https://bugzilla.kernel.org/show_bug.cgi?id=217242
Tested-by: Miller Hunter <MillerH@hearthnhome.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Message-ID: <20230602144009.1225632-8-mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The amount of new TRBs needed is calculated incorrectly when expanding a
transfer ring.
The room_on_ring() helper will correctly report that the ring needs
expansion if the enqueue pointer is about to reach the dequeue segment.
If enqueue reaches the dequeue segment then there is no easy way
to expand the ring by adding new segments between enqueue and dequeue.
This leads to ring expansion even if num_trbs_free is larger than
num_trbs we are queueing.
As a result we try to store a negative number in a unsigned int, leading
to a huge percieved trb need, and doubling of ring size.
Rework and rename the room_on_ring() to a helper that checks if ring
needs expansion, and return number of new segments needed. Don't rely on
the tracked ring->num_trbs_free value as turns out it has been unreliable.
Use ring enqueue and dequeue positions to determine expansion need.
The unsigned int issue was first reported first Chao zeng, and a bit
later seen in a real world bug.
Reported-by: chao zeng <chao.zengup@gmail.com>
Closes: https://bugzilla.kernel.org/show_bug.cgi?id=217242
Tested-by: Miller Hunter <MillerH@hearthnhome.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Message-ID: <20230602144009.1225632-7-mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The current function that both allocates and adds the interrupter isn't
optimal when using several interrupters. The array of interrupters need
to be protected with a lock while adding or removing interrupters.
If memory is allocated under the default xhci spinlock then GFP_KERNEL
can't be used.
There is no need to allocate the interrupter memory under the lock, so
split this code into separate unlocked allocate part, and a lock
protected add part.
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Message-ID: <20230602144009.1225632-6-mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The XHCI_PLAT quirk was only needed to ensure non-PCI xHC host avoided
setting up MSI interrupts in generic xhci codepaths.
The MSI setup code is now moved to PCI specific xhci-pci.c file so
the quirk is no longer needed.
Remove setting the XHCI_PLAT quirk for HiSilocon SoC xHC, NVIDIA Tegra xHC,
MediaTek xHC, the generic xhci-plat driver, and the checks for XHCI_PLAT
in xhci-pci.c MSI setup code.
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Message-ID: <20230602144009.1225632-5-mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Check for the cold attach (CAS) bit while checking for other usb3
roothub port changes during host resume.
The CAS bit is set if a USB 3 device is connected while the host is
suspended in such a way it can't perform proper link training and
progress the link to the enabled U0 state.
If the CAS bit set we want to resume the root hub, and reset and
enumerate the newly connected device.
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Message-ID: <20230602144009.1225632-3-mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
