If we are doing async removal of the session, we could be doing a
scsi_remove_target from the removal workqueue, and for the offload case we
could be doing a new session addition and scan to the same host. The
add/scan might then end up trying to use the target_id of the target we are
removing.
This patch just has a delay the freeing of the target_id until after the
scsi_remove_target has completed, so we know it's no longer in use.
Link: https://lore.kernel.org/r/1593632868-6808-2-git-send-email-michael.christie@oracle.com
Reviewed-by: Lee Duncan <lduncan@suse.com>
Signed-off-by: Mike Christie <michael.christie@oracle.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The current logging methods typically end up requesting a reproduction with
a different logging level set to figure out what happened. This was mainly
by design to not clutter the kernel log messages with things that were
typically not interesting and the messages themselves could cause other
issues.
When looking to make a better system, it was seen that in many cases when
more data was wanted was when another message, usually at KERN_ERR level,
was logged. And in most cases, what the additional logging that was then
enabled was typically. Most of these areas fell into the discovery machine.
Based on this summary, the following design has been put in place: The
driver will maintain an internal log (256 elements of 256 bytes). The
"additional logging" messages that are usually enabled in a reproduction
will be changed to now log all the time to the internal log. A new logging
level is defined - LOG_TRACE_EVENT. When this level is set (it is not by
default) and a message marked as KERN_ERR is logged, all the messages in
the internal log will be dumped to the kernel log before the KERN_ERR
message is logged.
There is a timestamp on each message added to the internal log. However,
this timestamp is not converted to wall time when logged. The value of the
timestamp is solely to give a crude time reference for the messages.
Link: https://lore.kernel.org/r/20200630215001.70793-14-jsmart2021@gmail.com
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Although the existing implementation is very good at high I/O load, on
tests involving light load, especially on only a few hardware queues,
latency was a little higher than it can be due to using workqueue
scheduling. Other tasks in the system can delay handling.
Change the lower level to use irq_poll by default which uses a softirq for
I/O completion. This gives better latency as variance in when the cq is
processed is reduced over the workqueue interface. However, as high load is
better served by not being in softirq when the CPU is loaded, work queues
are still used under high I/O load.
Link: https://lore.kernel.org/r/20200630215001.70793-13-jsmart2021@gmail.com
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Change vocabulary of 0373 log msg from "error" to "cmpl" The current
language of the 0373 message contains the word "error" which caused a
number of customers to inquire about the "error" and if it should be a
concern. It isn't an error, it's simply an io completion status.
Revise the message to replace the word "error" with "cmpl" for completion.
Link: https://lore.kernel.org/r/20200630215001.70793-10-jsmart2021@gmail.com
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
When the kdump kernel shuts down lpfc calls flush_work_queue on an
interrupt to schedule the cq handler. When there is only one CPU active on
the kdump kernel, it is possible for the work_on to get scheduled on a
non-active CPU causing it to never be scheduled.
When in the kdump environment, per-CPU affinity of cq's to cpus is not
necessary. In those cases, use a general queue_work rather than a
queue_work_on().
Link: https://lore.kernel.org/r/20200630215001.70793-9-jsmart2021@gmail.com
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
When vports are deleted, it is observed that there is memory/kthread
leakage as the vport isn't fully being released.
There is a shost reference taken in scsi_add_host_dma that is not released
during scsi_remove_host. It was noticed that other drivers resolve this by
doing a scsi_host_put after calling scsi_remove_host.
The vport_delete routine is taking two references one that corresponds to
an access to the scsi_host in the vport_delete routine and another that is
released after the adapter mailbox command completes that destroys the VPI
that corresponds to the vport.
Remove one of the references taken such that the second reference that is
put will complete the missing scsi_add_host_dma reference and the shost
will be terminated.
Link: https://lore.kernel.org/r/20200630215001.70793-8-jsmart2021@gmail.com
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Call traces have been observed running different tests that involve aborts
and setting the rrq active flag. The lpfc_set_rrq_active routine is doing
a mempool_alloc under the soft_irq processing level. When the mempool needs
to get a new buffer from the free pool and has to wait for memory to become
free it will check the flags passed in on the alloc and dump the stack if
the thread is running in interrupt context.
Replace the GFP_KERNEL flag with GFP_ATOMIC so that the memory allocation
will not attempt to sleep if there is no mem available.
Link: https://lore.kernel.org/r/20200630215001.70793-7-jsmart2021@gmail.com
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
During driver unload/reload testing, the NVMe initiator would not
re-establish connectivity to NVMe controllers on reload.
The failing NVMe array supports concurrent FCP and NVMe operation via
different nport_id's. The array was repeatedly sending an ADISC every 2
seconds after PLOGI completed and while NVMe subsystems were executing
discovery. The target would continue this state for roughly 45 seconds.
The driver's current behavior on ADISC receipt is to validate a the ADISC
vs the device and issue a RESUME_RPI to restore transmission. The receipt
of the ADISC effectively caused a driver to take actions similar to a
logout and login for the remote port, causing the deregistration of the
nvme rport and a subsequent re-registration. This caused a constant reset
and re-connect of the NVMe controller while this 45s window occurred. There
was no need for the state changes as ADISC does not change login state.
This patch corrects this behavior by validating if the remoteport is
already logged in (MAPPED) and when true, avoids the call to set the ndlp
state to MAPPED, which triggers the unreg/re-reg. Thus ADISC does not
change the login state of the node.
Link: https://lore.kernel.org/r/20200630215001.70793-5-jsmart2021@gmail.com
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Coverity reported the following error:
Assigned value that is never used may represent unnecessary computation.
The rc variable was initially assigned a value but in several cases, when
an error case is detected, it is reassigned a new value. The initial value
had little use.
In code-reviewing this routine, it could use some cleanup:
- Setting the initialization value to -ENODEV is a much better choice and
lessens code in the routine.
- The wasn't tracking logic errors vs no error and mailbox failure.
Better to resolve by adding a status to track the mailbox failure
and merge it with the logic error when the routine returns.
Link: https://lore.kernel.org/r/20200630215001.70793-2-jsmart2021@gmail.com
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The request_t 'handle' member is 32-bits wide, hence use wrt_reg_dword().
Change the cast in the wrt_reg_byte() call to make it clear that a regular
pointer is casted to an __iomem pointer.
Note: 'pkt' points to I/O memory for the qlafx00 adapter family and to
coherent memory for all other adapter families.
This patch fixes the following Coverity complaint:
CID 358864 (#1 of 1): Reliance on integer endianness (INCOMPATIBLE_CAST)
incompatible_cast: Pointer &pkt->handle points to an object whose effective
type is unsigned int (32 bits, unsigned) but is dereferenced as a narrower
unsigned short (16 bits, unsigned). This may lead to unexpected results
depending on machine endianness.
Link: https://lore.kernel.org/r/20200629225454.22863-7-bvanassche@acm.org
Fixes: 8ae6d9c7eb ("[SCSI] qla2xxx: Enhancements to support ISPFx00.")
Cc: Nilesh Javali <njavali@marvell.com>
Cc: Quinn Tran <qutran@marvell.com>
Cc: Himanshu Madhani <himanshu.madhani@oracle.com>
Cc: Martin Wilck <mwilck@suse.com>
Cc: Roman Bolshakov <r.bolshakov@yadro.com>
Reviewed-by: Daniel Wagner <dwagner@suse.de>
Reviewed-by: Himanshu Madhani <himanshu.madhani@oracle.com>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
If tcmu_handle_completions() has to process a padding shorter than
sizeof(struct tcmu_cmd_entry), the current call to
tcmu_flush_dcache_range() with sizeof(struct tcmu_cmd_entry) as length
param is wrong and causes crashes on e.g. ARM, because
tcmu_flush_dcache_range() in this case calls
flush_dcache_page(vmalloc_to_page(start)); with start being an invalid
address above the end of the vmalloc'ed area.
The fix is to use the minimum of remaining ring space and sizeof(struct
tcmu_cmd_entry) as the length param.
The patch was tested on kernel 4.19.118.
See https://bugzilla.kernel.org/show_bug.cgi?id=208045#c10
Link: https://lore.kernel.org/r/20200629093756.8947-1-bstroesser@ts.fujitsu.com
Tested-by: JiangYu <lnsyyj@hotmail.com>
Acked-by: Mike Christie <michael.christie@oracle.com>
Signed-off-by: Bodo Stroesser <bstroesser@ts.fujitsu.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Allow Exynos UFS driver to build as a module. This patch fixes the
followin build issue reported by kernel build robot.
drivers/scsi/ufs/ufs-exynos.o: in function `exynos_ufs_probe':
drivers/scsi/ufs/ufs-exynos.c:1231: undefined reference to `ufshcd_pltfrm_init'
drivers/scsi/ufs/ufs-exynos.o: in function `exynos_ufs_pre_pwr_mode':
drivers/scsi/ufs/ufs-exynos.c:635: undefined reference to `ufshcd_get_pwr_dev_param'
drivers/scsi/ufs/ufs-exynos.o:undefined reference to `ufshcd_pltfrm_shutdown'
drivers/scsi/ufs/ufs-exynos.o:undefined reference to `ufshcd_pltfrm_suspend'
drivers/scsi/ufs/ufs-exynos.o:undefined reference to `ufshcd_pltfrm_resume'
drivers/scsi/ufs/ufs-exynos.o:undefined reference to `ufshcd_pltfrm_runtime_suspend'
drivers/scsi/ufs/ufs-exynos.o:undefined reference to `ufshcd_pltfrm_runtime_resume'
drivers/scsi/ufs/ufs-exynos.o:undefined reference to `ufshcd_pltfrm_runtime_idle'
Link: https://lore.kernel.org/r/20200620173232.52521-1-alim.akhtar@samsung.com
Fixes: 55f4b1f736 ("scsi: ufs: ufs-exynos: Add UFS host support for Exynos SoCs")
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Alim Akhtar <alim.akhtar@samsung.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
(scatter|gather)_data_area() need to flush dcache after writing data to or
before reading data from a page in uio data area. The two routines are
able to handle data transfer to/from such a page in fragments and flush the
cache after each fragment was copied by calling the wrapper
tcmu_flush_dcache_range().
That means:
1) flush_dcache_page() can be called multiple times for the same page.
2) Calling flush_dcache_page() indirectly using the wrapper does not make
sense, because each call of the wrapper is for one single page only and
the calling routine already has the correct page pointer.
Change (scatter|gather)_data_area() such that, instead of calling
tcmu_flush_dcache_range() before/after each memcpy, it now calls
flush_dcache_page() before unmapping a page (when writing is complete for
that page) or after mapping a page (when starting to read the page).
After this change only calls to tcmu_flush_dcache_range() for addresses in
vmalloc'ed command ring are left over.
The patch was tested on ARM with kernel 4.19.118 and 5.7.2
Link: https://lore.kernel.org/r/20200618131632.32748-2-bstroesser@ts.fujitsu.com
Tested-by: JiangYu <lnsyyj@hotmail.com>
Tested-by: Daniel Meyerholt <dxm523@gmail.com>
Acked-by: Mike Christie <michael.christie@oracle.com>
Signed-off-by: Bodo Stroesser <bstroesser@ts.fujitsu.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The UFS load calculation is based on "total_time" and "busy_time" in a
devfreq window. However, the source of time is different for both
parameters: "busy_time" is assigned from "jiffies" thus has different
accuracy from "total_time" which is assigned from ktime_get().
In addition, the time of window boundary is not exactly the same as the
starting busy time in this window if UFS is actually busy in the beginning
of the window. A similar accuracy error may also happen for the end of busy
time in current window.
To guarantee the precision of load calculation, we need to
1. Align time accuracy of both devfreq_dev_status.total_time and
devfreq_dev_status.busy_time. For example, use "ktime_get()" directly.
2. Align the following timelines:
- The beginning time of devfreq windows
- The beginning of busy time in a new window
- The end of busy time in the current window
Link: https://lore.kernel.org/r/20200611101043.6379-1-stanley.chu@mediatek.com
Fixes: a3cd5ec55f ("scsi: ufs: add load based scaling of UFS gear")
Reviewed-by: Avri Altman <avri.altman@wdc.com>
Signed-off-by: Stanley Chu <stanley.chu@mediatek.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
