Systems that issue PCIe hot reset requests during a suspend/resume
cycle cause PCI1XXXX device revisions prior to C0 to get its UART
configuration registers reset to hardware default values. This results
in device inaccessibility and data transfer failures. Starting with
Revision C0, support was added in the device hardware (via the Hot
Reset Disable Bit) to allow resetting only the PCIe interface and its
associated logic, but preserving the UART configuration during a hot
reset. This patch enables the hot reset disable feature during suspend/
resume for C0 and later revisions of the device.
Signed-off-by: Rengarajan S <rengarajan.s@microchip.com>
Reviewed-by: Jiri Slaby <jirislaby@kernel.org>
Link: https://lore.kernel.org/r/20250425145500.29036-1-rengarajan.s@microchip.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Pull PCI fixes from Bjorn Helgaas:
- When releasing a start-aligned resource, e.g., a bridge window, save
start/end/flags for the next assignment attempt; fixes a v6.15-rc1
regression (Ilpo Järvinen)
- Move set_pcie_speed.sh from TEST_PROGS to TEST_FILE; fixes a bwctrl
selftest v6.15-rc1 regression (Ilpo Järvinen)
- Add Manivannan Sadhasivam as maintainer of native host bridge and
endpoint drivers (Manivannan Sadhasivam)
- In endpoint test driver, defer IRQ allocation from .probe() until
ioctl() to fix a regression on platforms where the Vendor/Device ID
match doesn't include driver_data (Niklas Cassel)
* tag 'pci-v6.15-fixes-3' of git://git.kernel.org/pub/scm/linux/kernel/git/pci/pci:
misc: pci_endpoint_test: Defer IRQ allocation until ioctl(PCITEST_SET_IRQTYPE)
MAINTAINERS: Move Manivannan Sadhasivam as PCI Native host bridge and endpoint maintainer
selftests/pcie_bwctrl: Fix test progs list
PCI: Restore assigned resources fully after release
Pull nfsd fix from Chuck Lever:
- Revert a v6.15 patch due to a report of SELinux test failures
* tag 'nfsd-6.15-2' of git://git.kernel.org/pub/scm/linux/kernel/git/cel/linux:
Revert "sunrpc: clean cache_detail immediately when flush is written frequently"
Pull misc x86 fixes from Ingo Molnar:
- Fix 32-bit kernel boot crash if passed physical memory with more than
32 address bits
- Fix Xen PV crash
- Work around build bug in certain limited build environments
- Fix CTEST instruction decoding in insn_decoder_test
* tag 'x86-urgent-2025-04-26' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/insn: Fix CTEST instruction decoding
x86/boot: Work around broken busybox 'truncate' tool
x86/mm: Fix _pgd_alloc() for Xen PV mode
x86/e820: Discard high memory that can't be addressed by 32-bit systems
Pull scheduler fix from Ingo Molnar:
"Fix sporadic crashes in dequeue_entities() due to ... bad math.
[ Arguably if pick_eevdf()/pick_next_entity() was less trusting of
complex math being correct it could have de-escalated a crash into
a warning, but that's for a different patch ]"
* tag 'sched-urgent-2025-04-26' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
sched/eevdf: Fix se->slice being set to U64_MAX and resulting crash
Pull misc perf events fixes from Ingo Molnar:
- Use POLLERR for events in error state, instead of the ambiguous
POLLHUP error value
- Fix non-sampling (counting) events on certain x86 platforms
* tag 'perf-urgent-2025-04-26' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
perf/x86: Fix non-sampling (counting) events on certain x86 platforms
perf/core: Change to POLLERR for pinned events with error
Pull irq fix from Ingo Molnar:
"Fix crashes in the gic-v2m irqchip driver, caused by an incorrect
__init annotation"
* tag 'irq-urgent-2025-04-26' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
irqchip/gic-v2m: Prevent use after free of gicv2m_get_fwnode()
Pull LoongArch fixes from Huacai Chen:
"Add a missing Kconfig option, fix some bugs in exception handlers,
memory management and KVM"
* tag 'loongarch-fixes-6.15-1' of git://git.kernel.org/pub/scm/linux/kernel/git/chenhuacai/linux-loongson:
LoongArch: KVM: Fix PMU pass-through issue if VM exits to host finally
LoongArch: KVM: Fully clear some CSRs when VM reboot
LoongArch: KVM: Fix multiple typos of KVM code
LoongArch: Return NULL from huge_pte_offset() for invalid PMD
LoongArch: Remove a bogus reference to ZONE_DMA
LoongArch: Handle fp, lsx, lasx and lbt assembly symbols
LoongArch: Make do_xyz() exception handlers more robust
LoongArch: Make regs_irqs_disabled() more clear
LoongArch: Select ARCH_USE_MEMTEST
Pull OpenRISC updates from Stafford Horne:
- Support for cacheinfo API to expose OpenRISC cache info via sysfs,
this also translated to some cleanups to OpenRISC cache flush and
invalidate API's
- Documentation updates for new mailing list and toolchain binaries
* tag 'for-linus' of https://github.com/openrisc/linux:
Documentation: openrisc: Update toolchain binaries URL
Documentation: openrisc: Update mailing list
openrisc: Add cacheinfo support
openrisc: Introduce new utility functions to flush and invalidate caches
openrisc: Refactor struct cpuinfo_or1k to reduce duplication
Ondrej reports that certain SELinux tests are failing after commit
fc2a169c56 ("sunrpc: clean cache_detail immediately when flush is
written frequently"), merged during the v6.15 merge window.
Reported-by: Ondrej Mosnacek <omosnace@redhat.com>
Fixes: fc2a169c56 ("sunrpc: clean cache_detail immediately when flush is written frequently")
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Pull kunit fix from Kees Cook:
"A single fix for the kunit lib/tests/ relocation:
- Ensure prime numbers tests are included in KUnit test runs (Mark Brown)"
* tag 'move-lib-kunit-v6.15-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/kees/linux:
lib: Ensure prime numbers tests are included in KUnit test runs
Pull drm fixes from Dave Airlie:
"Weekly drm fixes, mostly amdgpu, with some exynos cleanups and a
couple of minor fixes, seems a bit quiet, but probably some lag from
Easter holidays.
amdgpu:
- P2P DMA fixes
- Display reset fixes
- DCN 3.5 fixes
- ACPI EDID fix
- LTTPR fix
- mode_valid() fix
exynos:
- fix spelling error
- remove redundant error handling in exynos_drm_vidi.c module
- marks struct decon_data as const in the exynos7_drm_decon driver
since it is only read
- Remove unnecessary checking in exynos_drm_drv.c module
meson:
- Fix VCLK calculation
panel:
- jd9365a: Fix reset polarity"
* tag 'drm-fixes-2025-04-26' of https://gitlab.freedesktop.org/drm/kernel:
drm/exynos: Fix spelling mistake "enqueu" -> "enqueue"
drm/exynos: exynos7_drm_decon: Consstify struct decon_data
drm/exynos: fixed a spelling error
drm/exynos/vidi: Remove redundant error handling in vidi_get_modes()
drm/exynos: Remove unnecessary checking
drm/amd/display: do not copy invalid CRTC timing info
drm/amd/display: Default IPS to RCG_IN_ACTIVE_IPS2_IN_OFF
drm/amd/display: Use 16ms AUX read interval for LTTPR with old sinks
drm/amd/display: Fix ACPI edid parsing on some Lenovo systems
drm/amdgpu: Allow P2P access through XGMI
drm/amd/display: Enable urgent latency adjustment on DCN35
drm/amd/display: Force full update in gpu reset
drm/amd/display: Fix gpu reset in multidisplay config
drm/amdgpu: Don't pin VRAM without DMABUF_MOVE_NOTIFY
drm/amdgpu: Use allowed_domains for pinning dmabufs
drm: panel: jd9365da: fix reset signal polarity in unprepare
drm/meson: use unsigned long long / Hz for frequency types
Revert "drm/meson: vclk: fix calculation of 59.94 fractional rates"
In the Unicode screen buffer, we follow double-width code points with a
space to maintain proper column alignment. This, however, creates
semantic problems when e.g. using cut and paste.
Let's use a better code point for the column padding's purpose i.e. a
zero-width space rather than a full space. This way the combination
retains a width of 2.
Signed-off-by: Nicolas Pitre <npitre@baylibre.com>
Reviewed-by: Jiri Slaby <jirislaby@kernel.org>
Link: https://lore.kernel.org/r/20250417184849.475581-11-nico@fluxnic.net
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The generated table maps base character + combining mark pairs to their
precomposed equivalents using Python's unicodedata module.
The default script behavior is to create a table with most commonly used
Latin, Greek, and Cyrillic recomposition pairs only. It is much smaller
than the table with all possible recomposition pairs (71 entries vs 1000
entries). But if one needs/wants the full table then simply running the
script with the --full argument will generate it.
Signed-off-by: Nicolas Pitre <npitre@baylibre.com>
Reviewed-by: Jiri Slaby <jirislaby@kernel.org>
Link: https://lore.kernel.org/r/20250417184849.475581-8-nico@fluxnic.net
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Zero-width Unicode code points are causing misalignment in vertically
aligned content, disrupting the visual layout. Let's handle zero-width
code points more intelligently.
Double-width code points are stored in the screen grid followed by a white
space code point to create the expected screen layout. When a double-width
code point is followed by a zero-width code point in the console incoming
bytestream (e.g., an emoji with a presentation selector) then we may
replace the white space padding by that zero-width code point instead of
dropping it. This maximize screen content information while preserving
proper layout.
If a zero-width code point is preceded by a single-width code point then
the above trick is not possible and such zero-width code point must
be dropped.
VS16 (Variation Selector 16, U+FE0F) is special as it typically doubles
the width of the preceding single-width code point. We handle that case
by giving VS16 a width of 1 instead of 0 when that happens.
Signed-off-by: Nicolas Pitre <npitre@baylibre.com>
Reviewed-by: Jiri Slaby <jirislaby@kernel.org>
Link: https://lore.kernel.org/r/20250417184849.475581-4-nico@fluxnic.net
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reverts commit 74045f6658.
A new version of the series was submitted, so it's easier to revert the
old one and add the new one due to the changes invovled.
Cc: Nicolas Pitre <nico@fluxnic.net>
Cc: Jiri Slaby <jirislaby@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reverts commit 2acaf27cd7.
A new version of the series was submitted, so it's easier to revert the
old one and add the new one due to the changes invovled.
Cc: Nicolas Pitre <nico@fluxnic.net>
Cc: Jiri Slaby <jirislaby@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reverts commit e88391f730.
A new version of the series was submitted, so it's easier to revert the
old one and add the new one due to the changes invovled.
Cc: Nicolas Pitre <nico@fluxnic.net>
Cc: Jiri Slaby <jirislaby@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reverts commit 26c94eb484.
A new version of the series was submitted, so it's easier to revert the
old one and add the new one due to the changes invovled.
Cc: Nicolas Pitre <nico@fluxnic.net>
Cc: Jiri Slaby <jirislaby@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reverts commit 3a1ab63aa0.
A new version of the series was submitted, so it's easier to revert the
old one and add the new one due to the changes invovled.
Cc: Nicolas Pitre <nico@fluxnic.net>
Cc: Jiri Slaby <jirislaby@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reverts commit f2347b0cdf.
A new version of the series was submitted, so it's easier to revert the
old one and add the new one due to the changes invovled.
Cc: Nicolas Pitre <nico@fluxnic.net>
Cc: Jiri Slaby <jirislaby@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reverts commit 54af55b990.
A new version of the series was submitted, so it's easier to revert the
old one and add the new one due to the changes invovled.
Cc: Nicolas Pitre <nico@fluxnic.net>
Cc: Jiri Slaby <jirislaby@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reverts commit cd6937d42b.
A new version of the series was submitted, so it's easier to revert the
old one and add the new one due to the changes invovled.
Cc: Nicolas Pitre <nico@fluxnic.net>
Cc: Jiri Slaby <jirislaby@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reverts commit 119ff0b0f4.
A new version of the series was submitted, so it's easier to revert the
old one and add the new one due to the changes invovled.
Cc: Nicolas Pitre <nico@fluxnic.net>
Cc: Jiri Slaby <jirislaby@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reverts commit c7cb5b0779.
A new version of the series was submitted, so it's easier to revert the
old one and add the new one due to the changes invovled.
Cc: Nicolas Pitre <nico@fluxnic.net>
Cc: Jiri Slaby <jirislaby@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reverts commit 547f57b88d.
A new version of the series was submitted, so it's easier to revert the
old one and add the new one due to the changes invovled.
Cc: Nicolas Pitre <nico@fluxnic.net>
Cc: Jiri Slaby <jirislaby@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reverts commit b35f7a773c.
A new version of the series was submitted, so it's easier to revert the
old one and add the new one due to the changes invovled.
Cc: Nicolas Pitre <nico@fluxnic.net>
Cc: Jiri Slaby <jirislaby@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reverts commit 8bfabff0bf.
A new version of the series was submitted, so it's easier to revert the
old one and add the new one due to the changes invovled.
Cc: Nicolas Pitre <nico@fluxnic.net>
Cc: Jiri Slaby <jirislaby@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There is a code path in dequeue_entities() that can set the slice of a
sched_entity to U64_MAX, which sometimes results in a crash.
The offending case is when dequeue_entities() is called to dequeue a
delayed group entity, and then the entity's parent's dequeue is delayed.
In that case:
1. In the if (entity_is_task(se)) else block at the beginning of
dequeue_entities(), slice is set to
cfs_rq_min_slice(group_cfs_rq(se)). If the entity was delayed, then
it has no queued tasks, so cfs_rq_min_slice() returns U64_MAX.
2. The first for_each_sched_entity() loop dequeues the entity.
3. If the entity was its parent's only child, then the next iteration
tries to dequeue the parent.
4. If the parent's dequeue needs to be delayed, then it breaks from the
first for_each_sched_entity() loop _without updating slice_.
5. The second for_each_sched_entity() loop sets the parent's ->slice to
the saved slice, which is still U64_MAX.
This throws off subsequent calculations with potentially catastrophic
results. A manifestation we saw in production was:
6. In update_entity_lag(), se->slice is used to calculate limit, which
ends up as a huge negative number.
7. limit is used in se->vlag = clamp(vlag, -limit, limit). Because limit
is negative, vlag > limit, so se->vlag is set to the same huge
negative number.
8. In place_entity(), se->vlag is scaled, which overflows and results in
another huge (positive or negative) number.
9. The adjusted lag is subtracted from se->vruntime, which increases or
decreases se->vruntime by a huge number.
10. pick_eevdf() calls entity_eligible()/vruntime_eligible(), which
incorrectly returns false because the vruntime is so far from the
other vruntimes on the queue, causing the
(vruntime - cfs_rq->min_vruntime) * load calulation to overflow.
11. Nothing appears to be eligible, so pick_eevdf() returns NULL.
12. pick_next_entity() tries to dereference the return value of
pick_eevdf() and crashes.
Dumping the cfs_rq states from the core dumps with drgn showed tell-tale
huge vruntime ranges and bogus vlag values, and I also traced se->slice
being set to U64_MAX on live systems (which was usually "benign" since
the rest of the runqueue needed to be in a particular state to crash).
Fix it in dequeue_entities() by always setting slice from the first
non-empty cfs_rq.
Fixes: aef6987d89 ("sched/eevdf: Propagate min_slice up the cgroup hierarchy")
Signed-off-by: Omar Sandoval <osandov@fb.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Link: https://lkml.kernel.org/r/f0c2d1072be229e1bdddc73c0703919a8b00c652.1745570998.git.osandov@fb.com
With ACPI in place, gicv2m_get_fwnode() is registered with the pci
subsystem as pci_msi_get_fwnode_cb(), which may get invoked at runtime
during a PCI host bridge probe. But, the call back is wrongly marked as
__init, causing it to be freed, while being registered with the PCI
subsystem and could trigger:
Unable to handle kernel paging request at virtual address ffff8000816c0400
gicv2m_get_fwnode+0x0/0x58 (P)
pci_set_bus_msi_domain+0x74/0x88
pci_register_host_bridge+0x194/0x548
This is easily reproducible on a Juno board with ACPI boot.
Retain the function for later use.
Fixes: 0644b3daca ("irqchip/gic-v2m: acpi: Introducing GICv2m ACPI support")
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Reviewed-by: Marc Zyngier <maz@kernel.org>
Cc: stable@vger.kernel.org
In function kvm_pre_enter_guest(), it prepares to enter guest and check
whether there are pending signals or events. And it will not enter guest
if there are, PMU pass-through preparation for guest should be cancelled
and host should own PMU hardware.
Cc: stable@vger.kernel.org
Fixes: f4e40ea9f7 ("LoongArch: KVM: Add PMU support for guest")
Signed-off-by: Bibo Mao <maobibo@loongson.cn>
Signed-off-by: Huacai Chen <chenhuacai@loongson.cn>
Some registers such as LOONGARCH_CSR_ESTAT and LOONGARCH_CSR_GINTC are
partly cleared with function _kvm_setcsr(). This comes from the hardware
specification, some bits are read only in VM mode, and however they can
be written in host mode. So they are partly cleared in VM mode, and can
be fully cleared in host mode.
These read only bits show pending interrupt or exception status. When VM
reset, the read-only bits should be cleared, otherwise vCPU will receive
unknown interrupts in boot stage.
Here registers LOONGARCH_CSR_ESTAT/LOONGARCH_CSR_GINTC are fully cleared
in ioctl KVM_REG_LOONGARCH_VCPU_RESET vCPU reset path.
Cc: stable@vger.kernel.org
Signed-off-by: Bibo Mao <maobibo@loongson.cn>
Signed-off-by: Huacai Chen <chenhuacai@loongson.cn>
