The chips can be configured to aggregate several frames into a single
USB transfer. Modify rtw_usb_rx_handler() to support this case.
RX aggregation improves the RX speed of RTL8811CU on certain ARM
systems, like the NanoPi NEO Core2. It also improves the RX speed of
RTL8822CU on some x86_64 systems.
Currently none of the chips are configured to aggregate frames.
Tested with RTL8822CU, RTL8811CU, and RTL8723DU.
Reviewed-by: Sascha Hauer <s.hauer@pengutronix.de>
Tested-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Bitterblue Smith <rtl8821cerfe2@gmail.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Link: https://patch.msgid.link/f845826d-de71-492d-9a22-e48c07989a1f@gmail.com
The delay option is the period in unit of second for WoWLAN firmware
to wait before the first scan. We get the option from cfg80211 and
practice it. Another, in some platform, WoWLAN firmware may found
configured network and then trigger resume process, before suspend
process is completed, lead to the wakeup function failed.
So the default value is set one to avoid the issue.
Signed-off-by: Chin-Yen Lee <timlee@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Link: https://patch.msgid.link/20240805090028.27768-5-pkshih@realtek.com
Net-detect is an option of WoWLAN to allow the device to
be woken up from suspend mode when configured network is detected.
When user enables net-detect and lets the device enter suspend
state, WoWLAN firmware will periodically scan until beacon or
probe response of configured networks are received. If configured
networks are detected, WoWLAN firmware will trigger resume process.
Signed-off-by: Chin-Yen Lee <timlee@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Link: https://patch.msgid.link/20240805090028.27768-4-pkshih@realtek.com
When net-detect is enabled, WoWLAN firmware will periodically
scan until beacon or probe response of configured networks are
received. To reduce power consumption, the FW-IPS mode is
implemented to keep WiFi chip in idle mode between each scan.
The FW-IPS is controlled by WoWLAN firmware to turn of some critical
electrical components, and is different from the original IPS mode
which most electrical components are turned off.
Signed-off-by: Chin-Yen Lee <timlee@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Link: https://patch.msgid.link/20240805090028.27768-3-pkshih@realtek.com
Driver has supported different WoWLAN reason code by commit 0e52102177
("wifi: rtw89: wow: update WoWLAN reason register for different FW")
since firmware version 0.27.80.0. The old driver can't support two
kinds of WoWLAN reason, so increase firmware format to v1.
Also driver tables of BB and RF registers and power values will be added
into v1 format.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Link: https://patch.msgid.link/20240805090028.27768-2-pkshih@realtek.com
Originally, rtw89_btc_phymap() and rtw89_btc_path_phymap() access chan
with hard-code RTW89_CHANCTX_0. But, they are problematic when the chip
supports multiple channels.
So, change their prototype and pass chanctx_idx ahead. Let callers still
pass RTW89_CHANCTX_0 for now, but we will refine callers in the following.
Signed-off-by: Zong-Zhe Yang <kevin_yang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Link: https://patch.msgid.link/20240727080650.12195-8-pkshih@realtek.com
Originally, we planed to fill MAC_0/1 indicators with chanctx and
use sub_entity_xxx for these things. However, there are some reasons
listed below which make us give up this plan after we know our Wi-Fi 7
HW design.
1. one link is bound to one HW band during its life time
but, one link might change chanctx dynamically
2. in concurrent mode, assume 1st vif is MLD
1st vif's 2nd link might use the same chanctx as 2nd vif
but, they are not on the same HW band
So, we let sub_entity_xxx stuffs deal with only chanctx now. And, to be
more readable, we rename sub_entity related words to chanctx.
No logic is changed.
Signed-off-by: Zong-Zhe Yang <kevin_yang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Link: https://patch.msgid.link/20240727080650.12195-4-pkshih@realtek.com
Originally during unassign-chanctx, MCC (multi-channel concurrency) is
re-planed before set-channel if need. But, we might calculate MCC stuffs
based on old channel info. And, the following set-channel might be racing
with FW MCC state mechanism. So, we refine this flow. Now, if MCC re-plan
is needed here, it will be done after set-channel.
Besides, to be more rigorous, we now ensure entity isn't paused before we
deal with MCC things here.
Signed-off-by: Zong-Zhe Yang <kevin_yang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Link: https://patch.msgid.link/20240727080650.12195-2-pkshih@realtek.com
For different firmware type, it could change IDMEM mode, so reset it to
default to avoid encountering error for RTL8851B/RTL8852B/RTL8852BT
if that kind of firmware was downloaded before.
rtw89_8851be 0000:02:00.0: Firmware version 0.29.41.3, cmd version 0, type 5
rtw89_8851be 0000:02:00.0: Firmware version 0.29.41.3, cmd version 0, type 3
rtw89_8851be 0000:02:00.0: MAC has already powered on
rtw89_8851be 0000:02:00.0: fw security fail
rtw89_8851be 0000:02:00.0: download firmware fail
rtw89_8851be 0000:02:00.0: [ERR]fwdl 0x1E0 = 0x62
rtw89_8851be 0000:02:00.0: [ERR]fwdl 0x83F2 = 0x8
rtw89_8851be 0000:02:00.0: [ERR]fw PC = 0xb892f51c
rtw89_8851be 0000:02:00.0: [ERR]fw PC = 0xb892f524
rtw89_8851be 0000:02:00.0: [ERR]fw PC = 0xb892f51c
rtw89_8851be 0000:02:00.0: [ERR]fw PC = 0xb892f500
rtw89_8851be 0000:02:00.0: [ERR]fw PC = 0xb892f51c
rtw89_8851be 0000:02:00.0: [ERR]fw PC = 0xb892f53c
rtw89_8851be 0000:02:00.0: [ERR]fw PC = 0xb892f520
rtw89_8851be 0000:02:00.0: [ERR]fw PC = 0xb892f520
rtw89_8851be 0000:02:00.0: [ERR]fw PC = 0xb892f508
rtw89_8851be 0000:02:00.0: [ERR]fw PC = 0xb892f534
rtw89_8851be 0000:02:00.0: [ERR]fw PC = 0xb892f520
rtw89_8851be 0000:02:00.0: [ERR]fw PC = 0xb892f534
rtw89_8851be 0000:02:00.0: [ERR]fw PC = 0xb892f508
rtw89_8851be 0000:02:00.0: [ERR]fw PC = 0xb892f53c
rtw89_8851be 0000:02:00.0: [ERR]fw PC = 0xb892f524
rtw89_8851be 0000:02:00.0: failed to setup chip information
rtw89_8851be: probe of 0000:02:00.0 failed with error -16
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Link: https://patch.msgid.link/20240724052626.12774-4-pkshih@realtek.com
"iw dev wlp2s0 station dump" shows incorrect rx bitrate:
tx bitrate: 866.7 MBit/s VHT-MCS 9 80MHz short GI VHT-NSS 2
rx bitrate: 86.7 MBit/s VHT-MCS 9 VHT-NSS 1
This is because the RX band width is calculated incorrectly. Fix the
calculation according to the phydm_rxsc_2_bw() function from the
official drivers.
After:
tx bitrate: 866.7 MBit/s VHT-MCS 9 80MHz short GI VHT-NSS 2
rx bitrate: 390.0 MBit/s VHT-MCS 9 80MHz VHT-NSS 1
It also works correctly with the AP configured for 20 MHz and 40 MHz.
Tested with RTL8822CE.
Cc: stable@vger.kernel.org
Fixes: e3037485c6 ("rtw88: new Realtek 802.11ac driver")
Signed-off-by: Bitterblue Smith <rtl8821cerfe2@gmail.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Link: https://patch.msgid.link/bca8949b-e2bd-4515-98fd-70d3049a0097@gmail.com
clang warns precedence of '?:' and '&'. Even though original logic is
correct, use str_enable_disable() to avoid clang confusing. Another way to
fix is to add parentheses around '&', but I choose former one.
>> drivers/net/wireless/realtek/rtw89/rtw8852bt_rfk.c:1827:46: warning:
operator '?:' has lower precedence than '&'; '&' will be evaluated
first [-Wbitwise-conditional-parentheses]
1827 | kidx, dpk->is_dpk_enable & off_reverse ? "enable" : "disable");
| ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~ ^
Reported-by: kernel test robot <lkp@intel.com>
Closes: https://lore.kernel.org/oe-kbuild-all/202407200741.dMG9uvHU-lkp@intel.com/
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Link: https://patch.msgid.link/20240720021340.12102-3-pkshih@realtek.com
The Realtek wifi 5 devices which support USB 3 are weird: when first
plugged in, they pretend to be USB 2. The driver needs to send some
commands to the device, which make it disappear and come back as a
USB 3 device.
Implement the required commands in rtw88.
When a USB 3 device is plugged into a USB 2 port, rtw88 will try to
switch it to USB 3 mode only once. The device will disappear and come
back still in USB 2 mode, of course.
Some people experience heavy interference in the 2.4 GHz band in
USB 3 mode, so add a module parameter switch_usb_mode with the
default value 1 to let people disable the switching.
Signed-off-by: Bitterblue Smith <rtl8821cerfe2@gmail.com>
Acked-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Link: https://patch.msgid.link/77906c62-5674-426f-bde1-1b2a12a0339d@gmail.com
If we encounter an error on i2c packet transmit, we won't have a valid
flow anymore; since we didn't transmit a valid packet sequence, we'll
have to wait for the key to timeout instead of dropping it on the reply.
This causes the i2c lock to be held for longer than necessary.
Instead, invalidate the flow on TX error, and release the i2c lock
immediately.
Cc: Bonnie Lo <Bonnie_Lo@wiwynn.com>
Tested-by: Jerry C Chen <Jerry_C_Chen@wiwynn.com>
Signed-off-by: Jeremy Kerr <jk@codeconstruct.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
When handling colliding L2TPv3 session IDs, we use the existing
session IDR entry and link the new session on that using
session->coll_list. However, when using an existing IDR entry, we must
not do the idr_replace step.
Fixes: aa5e17e1f5 ("l2tp: store l2tpv3 sessions in per-net IDR")
Signed-off-by: James Chapman <jchapman@katalix.com>
Signed-off-by: Tom Parkin <tparkin@katalix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
link_is_up() and tipc_link_is_up() have the same functionality.
Consolidate these functions.
Signed-off-by: Shigeru Yoshida <syoshida@redhat.com>
Reviewed-by: Tung Nguyen <tung.q.nguyen@endava.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Breno Leitao says:
====================
netconsole: improve code clarity
These changes aim to enhance the reliability of netconsole by
eliminating the potential race condition and improve maintainability
by making the code more straightforward to understand and modify.
====================
Link: https://patch.msgid.link/20240709144403.544099-1-leitao@debian.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
When disabling a netconsole target, enabled_store() is called with
enabled=false. Currently, this results in updating the nt->enabled
field twice:
1. Inside the if/else block, with the target_list_lock spinlock held
2. Later, without the target_list_lock
This patch eliminates the redundancy by setting the field only once,
improving efficiency and reducing potential race conditions.
Signed-off-by: Breno Leitao <leitao@debian.org>
Link: https://patch.msgid.link/20240709144403.544099-3-leitao@debian.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
