As this struct is only used for devlink ports created for PF/VF,
add it to the name of the variable to distinguish from the SF related
ops struct.
Signed-off-by: Jiri Pirko <jiri@nvidia.com>
Reviewed-by: Shay Drory <shayd@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
It is not possible that the functions in devlink_port.c are called for
uplink port. Remove this leftover code.
Signed-off-by: Jiri Pirko <jiri@nvidia.com>
Reviewed-by: Shay Drory <shayd@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
For uplink port, mlx5_esw_offloads_load/unload_rep() are currently
called. There are 2 check inside, which effectively make the
functions a simple wrappers of mlx5_esw_offloads_rep_load/unload()
for uplink port. So avoid one check and indirection and call
mlx5_esw_offloads_rep_load/unload() for uplink port directly.
Signed-off-by: Jiri Pirko <jiri@nvidia.com>
Reviewed-by: Shay Drory <shayd@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Point to NVIDIA documentation for device specific information now that the
Mellanox documentation site is deprecated. Refer to kernel documentation
sources for generic information not specific to mlx5 devices.
Signed-off-by: Rahul Rameshbabu <rrameshbabu@nvidia.com>
Reviewed-by: Gal Pressman <gal@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Health syndrome enum values were duplicated in mlx5_ifc and health.c,
the correct place for them is mlx5_ifc.
Signed-off-by: Gal Pressman <gal@nvidia.com>
Reviewed-by: Rahul Rameshbabu <rrameshbabu@nvidia.com>
Reviewed-by: Moshe Shemesh <moshe@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Remove local variable that is already defined outside of
the scope of this block.
Signed-off-by: Yevgeny Kliteynik <kliteyn@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Consolidate the mlx5_irq and mlx5_irq->mask allocation, to simplify
error flows and to match the dealloctation sequence @irq_release for
symmetry.
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Reviewed-by: Shay Drory <shayd@nvidia.com>
Improve aRFS observability by adding new set of counters. Each Rx
ring will have this set of counters listed below.
These counters are exposed through ethtool -S.
1) arfs_add: number of times a new rule has been created.
2) arfs_request_in: number of times a rule was requested to move from
its current Rx ring to a new Rx ring (incremented on the destination
Rx ring).
3) arfs_request_out: number of times a rule was requested to move out
from its current Rx ring (incremented on source/current Rx ring).
4) arfs_expired: number of times a rule has been expired by the
kernel and removed from HW.
5) arfs_err: number of times a rule creation or modification has
failed.
This patch removes rx[i]_xsk_arfs_err counter and its documentation in
mlx5/counters.rst since aRFS activity does not occur in XSK RQ's.
Signed-off-by: Adham Faris <afaris@nvidia.com>
Reviewed-by: Tariq Toukan <tariqt@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Reviewed-by: Shay Drory <shayd@nvidia.com>
aRFS tables should be allocated and exist in advance. Driver shouldn't
reach a point where it tries to add aRFS rule to table that does not
exist.
Add warning if driver encounters such situation.
Signed-off-by: Adham Faris <afaris@nvidia.com>
Reviewed-by: Tariq Toukan <tariqt@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
aRFS rule movement requests from one Rx ring to other Rx ring arrive
from the kernel to ensure that packets are steered to the right Rx ring.
In the time interval until satisfying such a request, several more
requests might follow, for the same flow.
This patch detects and prevents repeated aRFS rules movement requests.
In mlx5e_rx_flow_steer() ndo, after finding the aRFS rule that have been
requested to move by the kernel, check if it's already requested to move
by calling work_busy(&arfs_rule->arfs_work) handler. IOW, if this
request is pending to be executed (in the work queue) or it's executing
now but hasn't finished yet, return current filter ID and don't issue a
new transition work.
Signed-off-by: Adham Faris <afaris@nvidia.com>
Reviewed-by: Tariq Toukan <tariqt@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Fix some kernel-doc comments to silence the warnings:
drivers/net/ethernet/amd/pds_core/auxbus.c:18: warning: Function parameter or member 'pf' not described in 'pds_client_register'
drivers/net/ethernet/amd/pds_core/auxbus.c:18: warning: Excess function parameter 'pf_pdev' description in 'pds_client_register'
drivers/net/ethernet/amd/pds_core/auxbus.c:58: warning: Function parameter or member 'pf' not described in 'pds_client_unregister'
drivers/net/ethernet/amd/pds_core/auxbus.c:58: warning: Excess function parameter 'pf_pdev' description in 'pds_client_unregister'
Signed-off-by: Yang Li <yang.lee@linux.alibaba.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
sk_getsockopt() runs locklessly. This means sk->sk_lingertime
can be read while other threads are changing its value.
Other reads also happen without socket lock being held,
and must be annotated.
Remove preprocessor logic using BITS_PER_LONG, compilers
are smart enough to figure this by themselves.
v2: fixed a clang W=1 (-Wtautological-constant-out-of-range-compare) warning
(Jakub)
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add extack info for IPv4 address add/delete, which would be useful for
users to understand the problem without having to read kernel code.
No extack message for the ifa_local checking in __inet_insert_ifa() as
it has been checked in find_matching_ifa().
Suggested-by: Ido Schimmel <idosch@idosch.org>
Signed-off-by: Hangbin Liu <liuhangbin@gmail.com>
Reviewed-by: David Ahern <dsahern@kernel.org>
Reviewed-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
1. XGMAC Core does not have hash_filter definition, it uses
vlhash(VLAN Hash Filtering) instead, skip hash_filter when XGMAC.
2. Show exact size of Hash Table instead of raw register value.
3. Show full description of safety features defined by Synopsys Databook.
4. When safety feature is configured with no parity, or ECC only,
keep FSM Parity Checking disabled.
Signed-off-by: Furong Xu <0x1207@gmail.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Hangbin Liu says:
====================
ipv6: update route when delete source address
Currently, when remove an address, the IPv6 route will not remove the
prefer source address when the address is bond to other device. Fix this
issue and add related tests as Ido and David suggested.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a test case for IPv6 source address delete.
As David suggested, add tests:
- Single device using src address
- Two devices with the same source address
- VRF with single device using src address
- VRF with two devices using src address
As Ido points out, in IPv6, the preferred source address is looked up in
the same VRF as the first nexthop device. This will give us similar results
to IPv4 if the route is installed in the same VRF as the nexthop device, but
not when the nexthop device is enslaved to a different VRF. So add tests:
- src address and nexthop dev in same VR
- src address and nexthop device in different VRF
The link local address delete logic is different from the global address.
It should only affect the associate device it bonds to. So add tests cases
for link local address testing.
Here is the test result:
IPv6 delete address route tests
Single device using src address
TEST: Prefsrc removed when src address removed on other device [ OK ]
Two devices with the same source address
TEST: Prefsrc not removed when src address exist on other device [ OK ]
TEST: Prefsrc removed when src address removed on all devices [ OK ]
VRF with single device using src address
TEST: Prefsrc removed when src address removed on other device [ OK ]
VRF with two devices using src address
TEST: Prefsrc not removed when src address exist on other device [ OK ]
TEST: Prefsrc removed when src address removed on all devices [ OK ]
src address and nexthop dev in same VRF
TEST: Prefsrc removed from VRF when source address deleted [ OK ]
TEST: Prefsrc in default VRF not removed [ OK ]
TEST: Prefsrc not removed from VRF when source address exist [ OK ]
TEST: Prefsrc in default VRF removed [ OK ]
src address and nexthop device in different VRF
TEST: Prefsrc not removed from VRF when nexthop dev in diff VRF [ OK ]
TEST: Prefsrc not removed in default VRF [ OK ]
TEST: Prefsrc removed from VRF when nexthop dev in diff VRF [ OK ]
TEST: Prefsrc removed in default VRF [ OK ]
Table ID 0
TEST: Prefsrc removed from default VRF when source address deleted [ OK ]
Link local source route
TEST: Prefsrc not removed when delete ll addr from other dev [ OK ]
TEST: Prefsrc removed when delete ll addr [ OK ]
TEST: Prefsrc not removed when delete ll addr from other dev [ OK ]
TEST: Prefsrc removed even ll addr still exist on other dev [ OK ]
Tests passed: 19
Tests failed: 0
Suggested-by: Ido Schimmel <idosch@idosch.org>
Suggested-by: David Ahern <dsahern@kernel.org>
Signed-off-by: Hangbin Liu <liuhangbin@gmail.com>
Reviewed-by: David Ahern <dsahern@kernel.org>
Reviewed-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
After deleting an IPv6 address on an interface and cleaning up the
related preferred source entries, it is important to ensure that all
routes associated with the deleted address are properly cleared. The
current implementation of rt6_remove_prefsrc() only checks the preferred
source addresses bound to the current device. However, there may be
routes that are bound to other devices but still utilize the same
preferred source address.
To address this issue, it is necessary to also delete entries that are
bound to other interfaces but share the same source address with the
current device. Failure to delete these entries would leave routes that
are bound to the deleted address unclear. Here is an example reproducer
(I have omitted unrelated routes):
+ ip link add dummy1 type dummy
+ ip link add dummy2 type dummy
+ ip link set dummy1 up
+ ip link set dummy2 up
+ ip addr add 1:2:3:4::5/64 dev dummy1
+ ip route add 7:7:7:0::1 dev dummy1 src 1:2:3:4::5
+ ip route add 7:7:7:0::2 dev dummy2 src 1:2:3:4::5
+ ip -6 route show
1:2:3:4::/64 dev dummy1 proto kernel metric 256 pref medium
7:7:7::1 dev dummy1 src 1:2:3:4::5 metric 1024 pref medium
7:7:7::2 dev dummy2 src 1:2:3:4::5 metric 1024 pref medium
+ ip addr del 1:2:3:4::5/64 dev dummy1
+ ip -6 route show
7:7:7::1 dev dummy1 metric 1024 pref medium
7:7:7::2 dev dummy2 src 1:2:3:4::5 metric 1024 pref medium
As Ido reminds, in IPv6, the preferred source address is looked up in
the same VRF as the first nexthop device, which is different with IPv4.
So, while removing the device checking, we also need to add an
ipv6_chk_addr() check to make sure the address does not exist on the other
devices of the rt nexthop device's VRF.
After fix:
+ ip addr del 1:2:3:4::5/64 dev dummy1
+ ip -6 route show
7:7:7::1 dev dummy1 metric 1024 pref medium
7:7:7::2 dev dummy2 metric 1024 pref medium
Reported-by: Thomas Haller <thaller@redhat.com>
Closes: https://bugzilla.redhat.com/show_bug.cgi?id=2170513
Reviewed-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: Hangbin Liu <liuhangbin@gmail.com>
Reviewed-by: David Ahern <dsahern@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
As the initial commit 1a01727676 ("selftests: Add VRF route leaking
tests") said, the IPv6 MTU test fails as source address selection
picking ::1. Every time we run the selftest this one report failed.
There seems not much meaning to keep reporting a failure for 3 years
that no one plan to fix/update. Let't just skip this one first. We can
add it back when the issue fixed.
Signed-off-by: Hangbin Liu <liuhangbin@gmail.com>
Reviewed-by: David Ahern <dsahern@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Setting IP_RECVERR and IPV6_RECVERR options to zero currently
purges the socket error queue, which was probably not expected
for zerocopy and tx_timestamp users.
I discovered this issue while preparing commit 6b5f43ea08
("inet: move inet->recverr to inet->inet_flags"), I presume this
change does not need to be backported to stable kernels.
Add skb_errqueue_purge() helper to purge error messages only.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Willem de Bruijn <willemb@google.com>
Cc: Soheil Hassas Yeganeh <soheil@google.com>
Reviewed-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ruan Jinjie says:
====================
net: Return PTR_ERR() for fixed_phy_register()
fixed_phy_register() returns not only -EIO or -ENODEV, but also
-EPROBE_DEFER, -EINVAL and -EBUSY. The Best practice is to return these
error codes with PTR_ERR().
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
fixed_phy_register() returns -EPROBE_DEFER, -EINVAL and -EBUSY,
etc, in addition to -EIO. The Best practice is to return these
error codes with PTR_ERR().
Signed-off-by: Ruan Jinjie <ruanjinjie@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
fixed_phy_register() returns -EPROBE_DEFER, -EINVAL and -EBUSY,
etc, in addition to -ENODEV. The Best practice is to return these
error codes with PTR_ERR().
Signed-off-by: Ruan Jinjie <ruanjinjie@huawei.com>
Acked-by: Doug Berger <opendmb@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
fixed_phy_register() returns -EPROBE_DEFER, -EINVAL and -EBUSY,
etc, in addition to -ENODEV. The best practice is to return
these error codes with PTR_ERR().
Signed-off-by: Ruan Jinjie <ruanjinjie@huawei.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The user ports use RSGMII, but we don't have that, and DT doesn't
specify a phy interface mode, so phylib defaults to GMII. These support
1G, 100M and 10M with flow control. It is unknown whether asymetric
pause is supported at all speeds.
The CPU port uses MII/GMII/RGMII/REVMII by hardware pin strapping,
and support speeds specific to each, with full duplex only supported
in some modes. Flow control may be supported again by hardware pin
strapping, and theoretically is readable through a register but no
information is given in the datasheet for that.
So, we do a best efforts - and be lenient.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ruan Jinjie says:
====================
net: Update and fix return value check for vcap_get_rule()
As Simon Horman suggests, update vcap_get_rule() to always
return an ERR_PTR() and update the error detection conditions to
use IS_ERR(), which would be more cleaner.
So se IS_ERR() to update the return value and fix the issue
in lan966x_ptp_add_trap().
Changes in v2:
- Update vcap_get_rule() to always return an ERR_PTR().
- Update the return value fix in lan966x_ptp_add_trap().
- Update the return value check in sparx5_tc_free_rule_resources().
====================
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
As Simon Horman suggests, update vcap_get_rule() to always
return an ERR_PTR() and update the error detection conditions to
use IS_ERR(), so use IS_ERR() to check the return value.
Signed-off-by: Ruan Jinjie <ruanjinjie@huawei.com>
Suggested-by: Simon Horman <horms@kernel.org>
Reviewed-by: Leon Romanovsky <leonro@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As Simon Horman suggests, update vcap_get_rule() to always
return an ERR_PTR() and update the error detection conditions to
use IS_ERR(), so use IS_ERR() to fix the return value issue.
Fixes: 72df3489fb ("net: lan966x: Add ptp trap rules")
Signed-off-by: Ruan Jinjie <ruanjinjie@huawei.com>
Suggested-by: Simon Horman <horms@kernel.org>
Reviewed-by: Leon Romanovsky <leonro@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As Simon Horman suggests, update vcap_get_rule() to always
return an ERR_PTR() and update the error detection conditions to
use IS_ERR(), which would be more cleaner in this case.
Signed-off-by: Ruan Jinjie <ruanjinjie@huawei.com>
Suggested-by: Simon Horman <horms@kernel.org>
Reviewed-by: Leon Romanovsky <leonro@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
xgene_mdio_status is declared static, and is only written once by the
driver. It appears to have been this way since the driver was first
added to the kernel tree. No other users can be found, so let's remove
it.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently any error during render leads to output an empty file.
That is quite annoying when using tools/net/ynl/ynl-regen.sh
which git greps files with content of "YNL-GEN.." and therefore ignores
empty files. So once you fail to regen, you have to checkout the file.
Avoid that by rendering to a temporary file first, only at the end
copy the content to the actual destination.
Signed-off-by: Jiri Pirko <jiri@nvidia.com>
Reviewed-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
All captured timestamps should be corrected by PHY, MAC and CDC introduced
latency/errors. The CDC correction is already used. Enable MAC propagation delay
correction as well which is available since commit 26cfb838aa ("net: stmmac:
correct MAC propagation delay").
Before:
|ptp4l[390.458]: rms 7 max 21 freq +177 +/- 14 delay 357 +/- 1
After:
|ptp4l[620.012]: rms 7 max 20 freq +195 +/- 14 delay 345 +/- 1
Tested on Intel Elkhart Lake.
Signed-off-by: Kurt Kanzenbach <kurt@linutronix.de>
Reviewed-by: Johannes Zink <j.zink@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
skb_queue_purge() and __skb_queue_purge() become wrappers
around the new generic functions.
New SKB_DROP_REASON_QUEUE_PURGE drop reason is added,
but users can start adding more specific reasons.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Guangguan Wang says:
====================
net/smc: several features's implementation for smc v2.1
This patch set implement several new features in SMC v2.1(https://
www.ibm.com/support/pages/node/7009315), including vendor unique
experimental options, max connections per lgr negotiation, max links
per lgr negotiation.
v1 - v2:
- rename field fce_v20 to fce_v2_base in struct
smc_clc_first_contact_ext_v2x
- use smc_get_clc_first_contact_ext in smc_connect
_rdma_v2_prepare
- adding comment about field vendor_oui in struct
smc_clc_msg_smcd
- remove comment about SMC_CONN_PER_LGR_MAX in smc_
clc_srv_v2x_features_validate
- rename smc_clc_clnt_v2x_features_validate
RFC v2 - v1:
- more description in commit message
- modify SMC_CONN_PER_LGR_xxx and SMC_LINKS_ADD_LNK_xxx
macro defination and usage
- rename field release_ver to release_nr
- remove redundant release version check in client
- explicitly set the rc value in smc_llc_cli/srv_add_link
RFC v1 - RFC v2:
- Remove ini pointer NULL check and fix code style in
smc_clc_send_confirm_accept.
- Optimize the max_conns check in smc_clc_xxx_v2x_features_validate.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Add SMC_NLA_LGR_R_V2_MAX_CONNS and SMC_NLA_LGR_R_V2_MAX_LINKS
to SMCR v2 linkgroup netlink attribute SMC_NLA_LGR_R_V2 for
linkgroup's detail info showing.
Signed-off-by: Guangguan Wang <guangguan.wang@linux.alibaba.com>
Reviewed-by: Jan Karcher <jaka@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Support max links per lgr negotiation in clc handshake for SMCR v2.1,
which is one of smc v2.1 features. Server makes decision for the final
value of max links based on the client preferred max links and
self-preferred max links. Here use the minimum value of the client
preferred max links and server preferred max links.
Client Server
Proposal(max links(client preferred))
-------------------------------------->
Accept(max links(accepted value))
accepted value=min(client preferred, server preferred)
<-------------------------------------
Confirm(max links(accepted value))
------------------------------------->
Signed-off-by: Guangguan Wang <guangguan.wang@linux.alibaba.com>
Reviewed-by: Tony Lu <tonylu@linux.alibaba.com>
Reviewed-by: Jan Karcher <jaka@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Support max connections per lgr negotiation for SMCR v2.1,
which is one of smc v2.1 features. Server makes decision for
the final value of max conns based on the client preferred
max conns and self-preferred max conns. Here use the minimum
value of client preferred max conns and server preferred max
conns.
Client Server
Proposal(max conns(client preferred))
------------------------------------>
Accept(max conns(accepted value))
accepted value=min(client preferred, server preferred)
<-----------------------------------
Confirm(max conns(accepted value))
----------------------------------->
Signed-off-by: Guangguan Wang <guangguan.wang@linux.alibaba.com>
Reviewed-by: Tony Lu <tonylu@linux.alibaba.com>
Reviewed-by: Jan Karcher <jaka@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Support SMC v2.x features validate for SMC v2.1. This is the frame
code for SMC v2.x features validate, and will take effects only when
the negotiated release version is v2.1 or later.
For Server, v2.x features' validation should be done in smc_clc_srv_
v2x_features_validate when receiving v2.1 or later CLC Proposal Message,
such as max conns, max links negotiation, the decision of the final
value of max conns and max links should be made in this function.
And final check for server when receiving v2.1 or later CLC Confirm
Message should be done in smc_clc_v2x_features_confirm_check.
For client, v2.x features' validation should be done in smc_clc_clnt_
v2x_features_validate when receiving v2.1 or later CLC Accept Message,
for example, the decision to accpt the accepted value or to decline
should be made in this function.
Signed-off-by: Guangguan Wang <guangguan.wang@linux.alibaba.com>
Reviewed-by: Tony Lu <tonylu@linux.alibaba.com>
Reviewed-by: Jan Karcher <jaka@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add vendor unique experimental options area in clc handshake. In clc
accept and confirm msg, vendor unique experimental options use the
16-Bytes reserved field, which defined in struct smc_clc_fce_gid_ext
in previous version. Because of the struct smc_clc_first_contact_ext
is widely used and limit the scope of modification, this patch moves
the 16-Bytes reserved field out of struct smc_clc_fce_gid_ext, and
followed with the struct smc_clc_first_contact_ext in a new struct
names struct smc_clc_first_contact_ext_v2x.
For SMC-R first connection, in previous version, the struct smc_clc_
first_contact_ext and the 16-Bytes reserved field has already been
included in clc accept and confirm msg. Thus, this patch use struct
smc_clc_first_contact_ext_v2x instead of the struct smc_clc_first_
contact_ext and the 16-Bytes reserved field in SMC-R clc accept and
confirm msg is compatible with previous version.
For SMC-D first connection, in previous version, only the struct smc_
clc_first_contact_ext is included in clc accept and confirm msg, and
the 16-Bytes reserved field is not included. Thus, when the negotiated
smc release version is the version before v2.1, we still use struct
smc_clc_first_contact_ext for compatible consideration. If the negotiated
smc release version is v2.1 or later, use struct smc_clc_first_contact_
ext_v2x instead.
Signed-off-by: Guangguan Wang <guangguan.wang@linux.alibaba.com>
Reviewed-by: Tony Lu <tonylu@linux.alibaba.com>
Reviewed-by: Jan Karcher <jaka@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Support smc release version negotiation in clc handshake based on
SMC v2, where no negotiation process for different releases, but
for different versions. The latest smc release version was updated
to v2.1. And currently there are two release versions of SMCv2, v2.0
and v2.1. In the release version negotiation, client sends the preferred
release version by CLC Proposal Message, server makes decision for which
release version to use based on the client preferred release version and
self-supported release version (here choose the minimum release version
of the client preferred and server latest supported), then the decision
returns to client by CLC Accept Message. Client confirms the decision by
CLC Confirm Message.
Client Server
Proposal(preferred release version)
------------------------------------>
Accept(accpeted release version)
min(client preferred, server latest supported)
<------------------------------------
Confirm(accpeted release version)
------------------------------------>
Signed-off-by: Guangguan Wang <guangguan.wang@linux.alibaba.com>
Reviewed-by: Tony Lu <tonylu@linux.alibaba.com>
Reviewed-by: Jan Karcher <jaka@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Enabling BIG TCP on a low end platform apparently increased
chances of getting flows locked on one busy TX queue.
A similar problem was handled in commit 9b462d02d6
("tcp: TCP Small Queues and strange attractors"),
but the strategy worked for either bulk flows,
or 'large enough' RPC. BIG TCP changed how large
RPC needed to be to enable the work around:
If RPC fits in a single skb, TSQ never triggers.
Root cause for the problem is a busy TX queue,
with delayed TX completions.
This patch changes how we set skb->ooo_okay to detect
the case TX completion was not done, but incoming ACK
already was processed and emptied rtx queue.
Update the comment to explain the tricky details.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Link: https://lore.kernel.org/r/20230817182353.2523746-1-edumazet@google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Michael Chan says:
====================
bnxt_en: Update for net-next
This patchset contains 2 features:
- The page pool implementation for the normal RX path (non-XDP) for
paged buffers in the aggregation ring.
- Saving of the ring error counters across reset.
====================
Link: https://lore.kernel.org/r/20230817231911.165035-1-michael.chan@broadcom.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
If we are doing a complete reset with irq_re_init set to true in
bnxt_close_nic(), all the ring structures will be freed. New
structures will be allocated in bnxt_open_nic(). The current code
increments rx_resets counter in bnxt_enable_napi() if bnapi->in_reset
is true. In a complete reset, bnapi->in_reset will never be true
since the structure is just allocated.
Increment the rx_resets counter in bnxt_disable_napi() instead. This
will allow us to save all the ring error counters including the
rx_resets counters in the next patch.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Link: https://lore.kernel.org/r/20230817231911.165035-4-michael.chan@broadcom.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
