Pull dma-buf updates from Sumit Semwal:
"A fairly small dma-buf pull request for 3.8 - only 2 patches"
* tag 'tag-for-linus-3.8' of git://git.linaro.org/people/sumitsemwal/linux-dma-buf:
dma-buf: remove fallback for !CONFIG_DMA_SHARED_BUFFER
dma-buf: might_sleep() in dma_buf_unmap_attachment()
Pull hwmon subsystem update from Jean Delvare:
"There are many improvements to the it87 driver, as well as suspend
support for the Winbond Super-I/O chips, and a few other fixes."
* 'hwmon-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jdelvare/staging:
hwmon-vid: Add support for AMD family 11h to 15h processors
hwmon: (it87) Support PECI for additional chips
hwmon: (it87) Report thermal sensor type as Intel PECI if appropriate
hwmon: (it87) Manage device specific features with table
hwmon: (it87) Replace pwm group macro with direct attribute definitions
hwmon: (it87) Avoid quoted string splits across lines
hwmon: (it87) Save fan registers in 2-dimensional array
hwmon: (it87) Introduce support for tempX_offset sysfs attribute
hwmon: (it87) Replace macro defining tempX_type sensors with direct definitions
hwmon: (it87) Save voltage register values in 2-dimensional array
hwmon: (it87) Save temperature registers in 2-dimensional array
hwmon: (w83627ehf) Get rid of smatch warnings
hwmon: (w83627hf) Don't touch nonexistent I2C address registers
hwmon: (w83627ehf) Add support for suspend
hwmon: (w83627hf) Add support for suspend
hwmon: Fix PCI device reference leak in quirk
The rmap walks in ksm.c are like those in rmap.c: they can safely be
done with anon_vma_lock_read().
Signed-off-by: Hugh Dickins <hughd@google.com>
Acked-by: Mel Gorman <mgorman@suse.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
task_numa_placement() oopsed on NULL p->mm when task_numa_fault() got
called in the handling of break_ksm() for ksmd. That might be a
peculiar case, which perhaps KSM could takes steps to avoid? but it's
more robust if task_numa_placement() allows for such a possibility.
Signed-off-by: Hugh Dickins <hughd@google.com>
Acked-by: Mel Gorman <mgorman@suse.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
On a 4GB RAM machine, where Normal zone is much smaller than DMA32 zone,
the Normal zone gets fragmented in time. This requires relatively more
pressure in balance_pgdat to get the zone above the required watermark.
Unfortunately, the congestion_wait() call in there slows it down for a
completely wrong reason, expecting that there's a lot of
writeback/swapout, even when there's none (much more common). After a
few days, when fragmentation progresses, this flawed logic translates to
a very high CPU iowait times, even though there's no I/O congestion at
all. If THP is enabled, the problem occurs sooner, but I was able to
see it even on !THP kernels, just by giving it a bit more time to occur.
The proper way to deal with this is to not wait, unless there's
congestion. Thanks to Mel Gorman, we already have the function that
perfectly fits the job. The patch was tested on a machine which nicely
revealed the problem after only 1 day of uptime, and it's been working
great.
Signed-off-by: Zlatko Calusic <zlatko.calusic@iskon.hr>
Acked-by: Mel Gorman <mgorman@suse.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Documentation says that code requiring dma-buf should add it to
select, so inline fallbacks are not going to be used. A link error
will make it obvious what went wrong, instead of silently doing
nothing at runtime.
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@canonical.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Reviewed-by: Rob Clark <rob.clark@linaro.org>
Signed-off-by: Sumit Semwal <sumit.semwal@linaro.org>
We never really clarified if unmap could be done in atomic context.
But since mapping might require sleeping, this implies mutex in use
to synchronize mapping/unmapping, so unmap could sleep as well. Add
a might_sleep() to clarify this.
Signed-off-by: Rob Clark <rob@ti.com>
Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@canonical.com>
Signed-off-by: Sumit Semwal <sumit.semwal@linaro.org>
Pull sparc fixes from David Miller:
"Please pull to get these sparc AES/DES/CAMELLIA crypto bug fixes as
well as an addition of a pte_accessible() define for sparc64 and a
hugetlb fix from Dave Kleikamp."
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/sparc:
sparc64: Set CRYPTO_TFM_REQ_MAY_SLEEP consistently in CAMELLIA code.
sparc64: Set CRYPTO_TFM_REQ_MAY_SLEEP consistently in DES code.
sparc64: Fix ECB looping constructs in AES code.
sparc64: Set CRYPTO_TFM_REQ_MAY_SLEEP consistently in AES code.
sparc64: Fix AES ctr mode block size.
sparc64: Fix unrolled AES 256-bit key loops.
sparc64: Define pte_accessible()
sparc: huge_ptep_set_* functions need to call set_huge_pte_at()
Pull networking fixes from David Miller:
1) Really fix tuntap SKB use after free bug, from Eric Dumazet.
2) Adjust SKB data pointer to point past the transport header before
calling icmpv6_notify() so that the headers are in the state which
that function expects. From Duan Jiong.
3) Fix ambiguities in the new tuntap multi-queue APIs. From Jason
Wang.
4) mISDN needs to use del_timer_sync(), from Konstantin Khlebnikov.
5) Don't destroy mutex after freeing up device private in mac802154,
fix also from Konstantin Khlebnikov.
6) Fix INET request socket leak in TCP and DCCP, from Christoph Paasch.
7) SCTP HMAC kconfig rework, from Neil Horman.
8) Fix SCTP jprobes function signature, otherwise things explode, from
Daniel Borkmann.
9) Fix typo in ipv6-offload Makefile variable reference, from Simon
Arlott.
10) Don't fail USBNET open just because remote wakeup isn't supported,
from Oliver Neukum.
11) be2net driver bug fixes from Sathya Perla.
12) SOLOS PCI ATM driver bug fixes from Nathan Williams and David
Woodhouse.
13) Fix MTU changing regression in 8139cp driver, from John Greene.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (45 commits)
solos-pci: ensure all TX packets are aligned to 4 bytes
solos-pci: add firmware upgrade support for new models
solos-pci: remove superfluous debug output
solos-pci: add GPIO support for newer versions on Geos board
8139cp: Prevent dev_close/cp_interrupt race on MTU change
net: qmi_wwan: add ZTE MF880
drivers/net: Use of_match_ptr() macro in smsc911x.c
drivers/net: Use of_match_ptr() macro in smc91x.c
ipv6: addrconf.c: remove unnecessary "if"
bridge: Correctly encode addresses when dumping mdb entries
bridge: Do not unregister all PF_BRIDGE rtnl operations
use generic usbnet_manage_power()
usbnet: generic manage_power()
usbnet: handle PM failure gracefully
ksz884x: fix receive polling race condition
qlcnic: update driver version
qlcnic: fix unused variable warnings
net: fec: forbid FEC_PTP on SoCs that do not support
be2net: fix wrong frag_idx reported by RX CQ
be2net: fix be_close() to ensure all events are ack'ed
...
Pull devicetree, gpio and spi bugfixes from Grant Likely:
"Device tree v3.8 bug fix:
- Fixes an undefined struct device build error and a missing symbol
export.
GPIO device driver bug fixes:
- gpio/mvebu-gpio: Make mvebu-gpio depend on OF_CONFIG
- gpio/ich: Add missing spinlock init
SPI device driver bug fixes:
- Most of this is bug fixes to the core code and the sh-hspi and
s3c64xx device drivers.
- There is also a patch here to add DT support to the Atmel driver.
This one should have been in the first round, but I missed it.
It's a low risk change contained within a single driver and the
Atmel maintainer has requested it."
* tag 'dt-for-linus' of git://git.secretlab.ca/git/linux-2.6:
of: define struct device in of_platform.h if !OF_DEVICE and !OF_ADDRESS
of: Fix export of of_find_matching_node_and_match()
* tag 'gpio-for-linus' of git://git.secretlab.ca/git/linux-2.6:
gpio/mvebu-gpio: Make mvebu-gpio depend on OF_CONFIG
gpio/ich: Add missing spinlock init
* tag 'spi-for-linus' of git://git.secretlab.ca/git/linux-2.6:
spi/sh-hspi: fix return value check in hspi_probe().
spi: fix tegra SPI binding examples
spi/atmel: add DT support
of/spi: Fix SPI module loading by using proper "spi:" modalias prefixes.
spi: Change FIFO flush operation and spi channel off
spi: Keep chipselect assertion during one message
Pull drm bugfix from Dave Airlie:
"Just a single urgent regression fix, seeing a few wierd behaviours I'd
like not to persist."
* 'drm-next' of git://people.freedesktop.org/~airlied/linux:
drm/ttm: fix delayed ttm_bo_cleanup_refs_and_unlock delayed handling
Pull random updates from Ted Ts'o:
"A few /dev/random improvements for the v3.8 merge window."
* tag 'random_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tytso/random:
random: Mix cputime from each thread that exits to the pool
random: prime last_data value per fips requirements
random: fix debug format strings
random: make it possible to enable debugging without rebuild
Like the generic versions, we need to support a block size
of '1' for CTR mode AES.
This was discovered thanks to all of the new test cases added by
Jussi Kivilinna.
Signed-off-by: David S. Miller <davem@davemloft.net>
The basic scheme of the block mode assembler is that we start by
enabling the FPU, loading the key into the floating point registers,
then iterate calling the encrypt/decrypt routine for each block.
For the 256-bit key cases, we run short on registers in the unrolled
loops.
So the {ENCRYPT,DECRYPT}_256_2() macros reload the key registers that
get clobbered.
The unrolled macros, {ENCRYPT,DECRYPT}_256(), are not mindful of this.
So if we have a mix of multi-block and single-block calls, the
single-block unrolled 256-bit encrypt/decrypt can run with some
of the key registers clobbered.
Handle this by always explicitly loading those registers before using
the non-unrolled 256-bit macro.
This was discovered thanks to all of the new test cases added by
Jussi Kivilinna.
Signed-off-by: David S. Miller <davem@davemloft.net>
The FPGA can't handled unaligned DMA (yet). So copy into an aligned buffer,
if skb->data isn't suitably aligned.
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
dwmw2: Tidy up a little, simpler matching on which GPIO is being accessed,
only register on newer boards, register under PCI device instead of
duplicating them under each ATM device.
Signed-off-by: Nathan Williams <nathan@traverse.com.au>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
commit: cb64edb6b8 upstream
Above commit may introduce a race between cp_interrupt and dev_close
/ change MTU / dev_open up state. Changes cp_interrupt to tolerate
this. Change spin_locking in cp_interrupt to avoid possible
but unobserved race.
Reported-by: "Francois Romieu" <romieu@fr.zoreil.com>
Tested on virtual hardware, Tx MTU size up to 4096, max tx payload
was ping -s 4068 for MTU of 4096. No real hardware, need test
assist.
Signed-off-by: "John Greene" <jogreene@redhat.com>
CC: "David S. Miller" <davem@davemloft.net>
CC: "David Woodhouse" <David.Woodhouse@intel.com>
Tested-by: David Woodhouse <David.Woodhouse@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When building without device tree support (for the mv78x00 SoCs for
example), the build failed because of_irq_count is undeclared. However
mvebu-gpio is not designed to build without device tree support. So
make it depends on OF_CONFIG, remove the #ifdef OF_CONFIG line and the
platform_device_id.
Tested on RD-78x00-mASA, DB-78460-BP, DB-88F6710-BP-DDR3,
DB-MV784MP-GP, Mirabox and OpenBlocks AX3.
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Since family 11h processors, AMD is exclusively using 7-bit VID codes
transmitted using a serial protocol over two pins (clock and data.)
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Tested-by: David Hubbard <david.c.hubbard@gmail.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Extend support for reporting and selecting PECI temperature sensors
to IT8718, IT8720, IT8782, and IT8783. For IT8721, report the sensor
type for temp2 as Intel PECI (6) if the chip is configured to report
the PCH temperature.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
IT8721 and IT8728 support Intel PECI temperature reporting. Each sensor
can be programmed to display the temperature reported on the PECI interface.
If configured for Intel PECI, the driver reported the wrong sensor type for
the respective thermal sensor. Fix the code to correctly report it as
"Intel PECI (6)".
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
This simplifies the code, improves runtime performance, reduces
code size (about 280 bytes on x86_64), and makes it easier
to add support for new devices.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Fix checkpatch error:
ERROR: Macros with multiple statements should be enclosed in a do - while loop
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Also unify fan functions to use the same code for 8 and 16 bit fans.
This patch reduces code size by approximately 1,200 bytes on x86_64.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
The macro name show_sensor_offset is confusing since it related to the sensor
type, not an offset - even more so when we introduce offset attributes later on.
Replace it with direct definitions, and replace the show_sensor/set_sensor
function names with show_temp_type/set_temp_type. This also resolves a
checkpatch error.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Reduces code size (more than 600 bytes on x86_64),
and gets rid of some checkpatch errors.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cleaner code, fewer checkpatch errors, and reduced code size
(saves more than 500 bytes on x86-64).
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
The smatch static code analyzer complains:
drivers/hwmon/w83627ehf.c:911 w83627ehf_update_device() error: buffer overflow 'W83627EHF_REG_TEMP_OFFSET' 3 <= 8
drivers/hwmon/w83627ehf.c:909 w83627ehf_update_device() error: buffer overflow 'data->temp_offset' 3 <= 8
drivers/hwmon/w83627ehf.c:2672 w83627ehf_resume() error: buffer overflow 'W83627EHF_REG_TEMP_OFFSET' 3 <= 8
drivers/hwmon/w83627ehf.c:2673 w83627ehf_resume() error: buffer overflow 'data->temp_offset' 3 <= 8
A deeper analysis of the code shows that these are false positives, as
only the lower 3 bits of data->have_temp_offset can be set so the
write is never attempted with i >= 3. However this shows that the code
isn't very robust and future changes could easily introduce a buffer
overflow. So let's add a safety check to prevent that and make smatch
happy.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Peter Huewe <PeterHuewe@gmx.de>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Only the W83627HF could be accessed through I2C. All other supported
chips are LPC-only, so they do not have I2C address registers. Don't
write to nonexistent or reserved registers on these chips.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Guenter Roeck <linux@roeck-us.net>
On suspend some register values are lost, most notably the Value RAM
areas but also other limits and settings. Restore them on resume.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Tested-by: Guenter Roeck <linux@roeck-us.net>
On suspend some register values are lost, most notably the Value RAM
areas but also other limits. Restore them on resume. On top of that,
some fixups are needed to work around BIOS bugs, in particular when
the BIOS omits running the same initialization sequence on resume
that it does after boot. In that case we have to carry initialization
over suspend.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Guenter Roeck <linux@roeck-us.net>
Tested-by: Guenter Roeck <linux@roeck-us.net>
Thankfully this only affects systems with one specific south bridge
and is most probably harmless unless the hwmon module is heavily
cycled.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Guenter Roeck <linux@roeck-us.net>
Pull Xtensa patchset from Chris Zankel:
"This contains support of device trees, many fixes, and code clean-ups"
* tag 'xtensa-20121218' of git://github.com/czankel/xtensa-linux: (33 commits)
xtensa: don't try to build DTB when OF is disabled
xtensa: set the correct ethernet address for xtfpga
xtensa: clean up files to make them code-style compliant
xtensa: provide endianness macro for sparse
xtensa: fix RASID SR initialization
xtensa: initialize CPENABLE SR when core has one
xtensa: reset all timers on initialization
Use for_each_compatible_node() macro.
xtensa: add XTFPGA DTS
xtensa: add support for the XTFPGA boards
xtensa: add device trees support
xtensa: add IRQ domains support
xtensa: add U-Boot image support (uImage).
xtensa: clean up boot make rules
xtensa: fix mb and wmb definitions
xtensa: add s32c1i-based spinlock implementations
xtensa: add s32c1i-based bitops implementations
xtensa: add s32c1i-based atomic ops implementations
xtensa: add s32c1i sanity check
xtensa: add trap_set_handler function
...
Pull one final 386 removal patch from Peter Anvin.
IRQ 13 FPU error handling is gone. That was not one of the proudest
moments in PC history.
* 'x86/nuke386' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86, 386 removal: Remove support for IRQ 13 FPU error reporting
Pull small x86 fixes from Peter Anvin:
"A collection of very small fixes, mostly pure documentation."
* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86, doc: Document that bootloader ID 4 is used also by iPXE
x86, doc: Add a formal bootloader ID for kexec-tools
x86, 8042: Enable A20 using KBC to fix S3 resume on some MSI laptops
The driver description files gives these names to the vendor specific
functions on this modem:
diag: VID_19D2&PID_0284&MI_00
nmea: VID_19D2&PID_0284&MI_01
at: VID_19D2&PID_0284&MI_02
mdm: VID_19D2&PID_0284&MI_03
net: VID_19D2&PID_0284&MI_04
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
This eliminates having an #ifdef returning NULL for the case
when OF is disabled.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
the value of err is always negative if it goes to errout, so we don't need to
check the value of err.
Signed-off-by: Cong Ding <dinggnu@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When dumping mdb table, set the addresses the kernel returns
based on the address protocol type.
Signed-off-by: Vlad Yasevich <vyasevic@redhat.com>
Acked-by: Cong Wang <amwang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
