This adds a device-tree definition for the CSI0 MCLK pin,
which can be used for feeding MIPI CSI-2 sensors.
Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
The H6 SoC contains an undocumented but fully functional RSB controller.
Add support for it. The MMIO register address matches other SoCs of the
same generation, and the IRQ matches a hole in the documented IRQ list.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Acked-by: Maxime Ripard <mripard@kernel.org>
[wens@csie.org: Use raw numbers instead of macros for clock/reset index]
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
In contrast to the H6 (and later) manuals, the A64 datasheet does not
specify any limitations in the maximum possible frequency for eMMC
controllers.
However experimentation has found that a 150 MHz limit similar to other
SoCs and also the MMC0 and MMC1 controllers on the A64 seems to exist
for the MMC2 controller.
Limit the frequency for the MMC2 controller to 150 MHz in the SoC .dtsi.
The Pinebook seems to be the an odd exception, since it apparently seems
to work with 200 MHz as well, so overwrite this in its board .dts file.
Tested on a Pine64-LTS: 200 MHz HS-200 fails, 150 MHz HS-200 works.
Fixes: 22be992fae ("arm64: allwinner: a64: Increase the MMC max frequency")
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://lore.kernel.org/r/20210113152630.28810-7-andre.przywara@arm.com
The H6 manual explicitly lists a frequency limit of 150 MHz for the bus
frequency of the MMC controllers. So far we had no explicit limits in the
DT, which limited eMMC to the spec defined frequencies, or whatever the
driver defines (both Linux and FreeBSD use 52 MHz here).
Put those maximum frequencies in the SoC .dtsi, to allow higher speed
modes (which still would need to be explicitly enabled, per board).
Tested with an eMMC using HS-200 on a Pine H64. Running at the spec'ed
200 MHz indeed fails with I/O errors, but 150 MHz seems to work stably.
Fixes: 8f54bd1595 ("arm64: allwinner: h6: add device tree nodes for MMC controllers")
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://lore.kernel.org/r/20210113152630.28810-6-andre.przywara@arm.com
The SD card on the SoPine SoM module is somewhat concealed, so was
originally defined as "non-removable".
However there is a working card-detect pin (tested on two different
SoM versions), and in certain SoM base boards it might be actually
accessible at runtime.
Also the Pine64-LTS shares the SoPine base .dtsi, so inherited the
non-removable flag, even though the SD card slot is perfectly accessible
and usable there. (It turns out that just *my* board has a broken card
detect switch, so I originally thought CD wouldn't work on the LTS.)
Drop the "non-removable" flag to describe the SD card slot properly.
Fixes: c3904a2698 ("arm64: allwinner: a64: add DTSI file for SoPine SoM")
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://lore.kernel.org/r/20210113152630.28810-5-andre.przywara@arm.com
In recent Allwinner SoCs the first USB host controller (HCI0) shares
the first PHY with the MUSB controller. Probably to make this sharing
work, we were avoiding to declare this in the DT. This has two
shortcomings:
- U-Boot (which uses the same .dts) cannot use this port in host mode
without a PHY linked, so we were loosing one USB port there.
- It requires the MUSB driver to be enabled and loaded, although we
don't actually use it.
To avoid those issues, let's add this PHY link to the H6 .dtsi file.
After all PHY port 0 *is* connected to HCI0, so we should describe
it as this.
This makes it work in U-Boot, also improves compatiblity when no MUSB
driver is loaded (for instance in distribution installers).
Fixes: eabb3d424b ("arm64: dts: allwinner: h6: add USB2-related device nodes")
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://lore.kernel.org/r/20210113152630.28810-3-andre.przywara@arm.com
In recent Allwinner SoCs the first USB host controller (HCI0) shares
the first PHY with the MUSB controller. Probably to make this sharing
work, we were avoiding to declare this in the DT. This has two
shortcomings:
- U-Boot (which uses the same .dts) cannot use this port in host mode
without a PHY linked, so we were loosing one USB port there.
- It requires the MUSB driver to be enabled and loaded, although we
don't actually use it.
To avoid those issues, let's add this PHY link to the A64 .dtsi file.
After all PHY port 0 *is* connected to HCI0, so we should describe
it as this. Remove the part from the Pinebook DTS which already had
this property.
This makes it work in U-Boot, also improves compatiblity when no MUSB
driver is loaded (for instance in distribution installers).
Fixes: dc03a047df ("arm64: allwinner: a64: add EHCI0/OHCI0 nodes to A64 DTSI")
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://lore.kernel.org/r/20210113152630.28810-2-andre.przywara@arm.com
R40 contains deinterlace core compatible to that in H3. One peculiarity
is that RAM gate is shared with CSI1. User manual states it's separate
but that's not true. Shared gate was verified with BSP Linux code check
and with runtime tests (CPU crashed if CSI1 gate was not ungated).
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://lore.kernel.org/r/20210106181901.1324075-3-jernej.skrabec@siol.net
The SL631 is a family of Allwinner V3 action cameras sold under
various names, such as SJCAM SJ4000 Air or F60 Action Camera.
Devices in this family share a common board design but can be found
with different image sensors, including the IMX179 and the OV4689.
This adds support for a common dtsi for the SL631 family as well as
a specific dts for the IMX179 fashion, which will later be populated
with an IMX179 node when a driver is available.
Features that were tested on the device include:
- UART debug
- MMC
- USB peripheral (e.g. g_ether)
- Buttons
- SPI NOR flash
Note that the exact designer/vendor of these boards is unknown.
Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://lore.kernel.org/r/20201206165131.1041983-6-contact@paulk.fr
This adds documentation for the compatible strings of the
SL631 Action Camera with IMX179.
Note that the device is sold under various different names, such as the
SJCAM SJ4000 Air or F60 Action Camera. This is a similar situation to
the Q8 tablets and just like them, the allwinner vendor is used as
fallback.
Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Reviewed-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20201206165131.1041983-5-contact@paulk.fr
This fixes a few things with the Pinecube AXP209 node:
- No compatible is required since it is using an AXP209 (not AXP203)
according to the schematics and this is what the included axp209.dtsi
already has;
- The interrupt-controller and #interrupt-cells properties are already
described in the included axp209.dtsi;
- The interrupt comes through the NMI controller, not directly through
the GIC.
Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://lore.kernel.org/r/20201206165131.1041983-4-contact@paulk.fr
The V3s/V3 has a NMI interrupt controller, mainly used for the AXP209.
Its address follows the system controller block, which was previously
incorrectly described as spanning over 0x1000 address bytes.
Even though this is what the Allwinner documentation indicates,
precedence from other SoCs such as the R40 suggests that this is not
actually the case.
This reduces the system controller address span up to the NMI
controller and adds a node for the controller, with its dedicated
compatible.
While the interrupt number was found in Allwinner's documentation,
the address for the controller is specified in any Allwinner SDK
supporting sun8iw8 (V3/V3s) at:
drivers/power/axp_power/axp20/axp20-board.c
It was tested to work on a V3 board with an AXP209 connected to the
NMI interrupt line.
Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://lore.kernel.org/r/20201206165131.1041983-3-contact@paulk.fr
Since commit 36e2c7421f ("fs: don't allow splice read/write without
explicit ops") we've required that file operation structures explicitly
enable splice support, rather than falling back to the default handlers.
Most /proc files use the indirect 'struct proc_ops' to describe their
file operations, and were fixed up to support splice earlier in commits
40be821d627c..b24c30c67863, but the mountinfo files interact with the
VFS directly using their own 'struct file_operations' and got missed as
a result.
This adds the necessary support for splice to work for /proc/*/mountinfo
and friends.
Reported-by: Joan Bruguera Micó <joanbrugueram@gmail.com>
Reported-by: Jussi Kivilinna <jussi.kivilinna@iki.fi>
Link: https://bugzilla.kernel.org/show_bug.cgi?id=209971
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Christoph Hellwig <hch@lst.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Pull NTB fixes from Jon Mason:
"Bug fix for IDT NTB and Intel NTB LTR management support"
* tag 'ntb-5.11' of git://github.com/jonmason/ntb:
ntb: intel: add Intel NTB LTR vendor support for gen4 NTB
ntb: idt: fix error check in ntb_hw_idt.c
Pull crypto fixes from Herbert Xu:
"Fix a number of autobuild failures due to missing Kconfig
dependencies"
* 'linus' of git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6:
crypto: qat - add CRYPTO_AES to Kconfig dependencies
crypto: keembay - Add dependency on HAS_IOMEM
crypto: keembay - CRYPTO_DEV_KEEMBAY_OCS_AES_SM4 should depend on ARCH_KEEMBAY
Pull objtool fix from Ingo Molnar:
"Fix a segfault that occurs when built with Clang"
* tag 'objtool-urgent-2020-12-27' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
objtool: Fix seg fault with Clang non-section symbols
Pull timer fixes from Ingo Molnar:
"Update/fix two CPU sanity checks in the hotplug and the boot code, and
fix a typo in the Kconfig help text.
[ Context: the first two commits are the result of an ongoing
annotation+review work of (intentional) tick_do_timer_cpu() data
races reported by KCSAN, but the annotations aren't fully cooked
yet ]"
* tag 'timers-urgent-2020-12-27' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
timekeeping: Fix spelling mistake in Kconfig "fullfill" -> "fulfill"
tick/sched: Remove bogus boot "safety" check
tick: Remove pointless cpu valid check in hotplug code
Pull scheduler fix from Ingo Molnar:
"Fix a context switch performance regression"
* tag 'sched-urgent-2020-12-27' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
sched: Optimize finish_lock_switch()
Commit c9a3c4e637 ("mfd: ab8500-debugfs: Remove extraneous curly
brace") removed a left-over curly brace that caused build failures, but
Joe Perches points out that the subsequent 'seq_putc()' should also be
removed, because the commit that caused all these problems already added
the final '\n' to the seq_printf() above it.
Reported-by: Joe Perches <joe@perches.com>
Fixes: 886c812165 ("mfd: ab8500-debugfs: Remove the racy fiddling with irq_desc")
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Nathan Chancellor <natechancellor@gmail.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Pull PCI fixes from Bjorn Helgaas:
- Fix a tegra enumeration regression (Rob Herring)
- Fix a designware-host check that warned on *success*, not failure
(Alexander Lobakin)
* tag 'pci-v5.11-fixes-1' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci:
PCI: dwc: Fix inverted condition of DMA mask setup warning
PCI: tegra: Fix host link initialization
Clang errors:
drivers/mfd/ab8500-debugfs.c:1526:2: error: non-void function does not return a value [-Werror,-Wreturn-type]
}
^
drivers/mfd/ab8500-debugfs.c:1528:2: error: expected identifier or '('
return 0;
^
drivers/mfd/ab8500-debugfs.c:1529:1: error: extraneous closing brace ('}')
}
^
3 errors generated.
The cleanup in ab8500_interrupts_show left a curly brace around, remove
it to fix the error.
Fixes: 886c812165 ("mfd: ab8500-debugfs: Remove the racy fiddling with irq_desc")
Signed-off-by: Nathan Chancellor <natechancellor@gmail.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Commit 660c486590 ("PCI: dwc: Set 32-bit DMA mask for MSI target address
allocation") added dma_mask_set() call to explicitly set 32-bit DMA mask
for MSI message mapping, but for now it throws a warning on ret == 0, while
dma_set_mask() returns 0 in case of success.
Fix this by inverting the condition.
[bhelgaas: join string to make it greppable]
Fixes: 660c486590 ("PCI: dwc: Set 32-bit DMA mask for MSI target address allocation")
Link: https://lore.kernel.org/r/20201222150708.67983-1-alobakin@pm.me
Signed-off-by: Alexander Lobakin <alobakin@pm.me>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Commit b9ac0f9dc8 ("PCI: dwc: Move dw_pcie_setup_rc() to DWC common
code") broke enumeration of downstream devices on Tegra:
In non-working case (next-20201211):
0001:00:00.0 PCI bridge: NVIDIA Corporation Device 1ad2 (rev a1)
0001:01:00.0 SATA controller: Marvell Technology Group Ltd. Device 9171 (rev 13)
0005:00:00.0 PCI bridge: NVIDIA Corporation Device 1ad0 (rev a1)
In working case (v5.10-rc7):
0001:00:00.0 PCI bridge: Molex Incorporated Device 1ad2 (rev a1)
0001:01:00.0 SATA controller: Marvell Technology Group Ltd. Device 9171 (rev 13)
0005:00:00.0 PCI bridge: Molex Incorporated Device 1ad0 (rev a1)
0005:01:00.0 PCI bridge: PLX Technology, Inc. Device 3380 (rev ab)
0005:02:02.0 PCI bridge: PLX Technology, Inc. Device 3380 (rev ab)
0005:03:00.0 USB controller: PLX Technology, Inc. Device 3380 (rev ab)
The problem seems to be dw_pcie_setup_rc() is now called twice before and
after the link up handling. The fix is to move Tegra's link up handling to
.start_link() function like other DWC drivers. Tegra is a bit more
complicated than others as it re-inits the whole DWC controller to retry
the link. With this, the initialization ordering is restored to match the
prior sequence.
Fixes: b9ac0f9dc8 ("PCI: dwc: Move dw_pcie_setup_rc() to DWC common code")
Link: https://lore.kernel.org/r/20201218143905.1614098-1-robh@kernel.org
Reported-by: Mian Yousaf Kaukab <ykaukab@suse.de>
Tested-by: Mian Yousaf Kaukab <ykaukab@suse.de>
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Thierry Reding <thierry.reding@gmail.com>
Cc: Jonathan Hunter <jonathanh@nvidia.com>
Cc: Vidya Sagar <vidyas@nvidia.com>
clang (quite rightly) complains fairly loudly about the newly added
mpc1_get_mpc_out_mux() function returning an uninitialized value if the
'opp_id' checks don't pass.
This may not happen in practice, but the code really shouldn't return
garbage if the sanity checks don't pass.
So just initialize 'val' to zero to avoid the issue.
Fixes: 110b055b28 ("drm/amd/display: add getter routine to retrieve mpcc mux")
Cc: Josip Pavic <Josip.Pavic@amd.com>
Cc: Bindu Ramamurthy <bindu.r@amd.com>
Cc: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Pull more perf tools updates from Arnaldo Carvalho de Melo:
- Refactor 'perf stat' per CPU/socket/die/thread aggregation fixing use
cases in ARM machines.
- Fix memory leak when synthesizing SDT probes in 'perf probe'.
- Update kernel header copies related to KVM, epol_pwait. msr-index and
powerpc and s390 syscall tables.
* tag 'perf-tools-2020-12-24' of git://git.kernel.org/pub/scm/linux/kernel/git/acme/linux: (24 commits)
perf probe: Fix memory leak when synthesizing SDT probes
perf stat aggregation: Add separate thread member
perf stat aggregation: Add separate core member
perf stat aggregation: Add separate die member
perf stat aggregation: Add separate socket member
perf stat aggregation: Add separate node member
perf stat aggregation: Start using cpu_aggr_id in map
perf cpumap: Drop in cpu_aggr_map struct
perf cpumap: Add new map type for aggregation
perf stat: Replace aggregation ID with a struct
perf cpumap: Add new struct for cpu aggregation
perf cpumap: Use existing allocator to avoid using malloc
perf tests: Improve topology test to check all aggregation types
perf tools: Update s390's syscall.tbl copy from the kernel sources
perf tools: Update powerpc's syscall.tbl copy from the kernel sources
perf s390: Move syscall.tbl check into check-headers.sh
perf powerpc: Move syscall.tbl check to check-headers.sh
tools headers UAPI: Synch KVM's svm.h header with the kernel
tools kvm headers: Update KVM headers from the kernel sources
tools headers UAPI: Sync KVM's vmx.h header with the kernel sources
...
Pull coccinelle updates from Julia Lawall.
* 'for-5.11' of git://git.kernel.org/pub/scm/linux/kernel/git/jlawall/linux:
scripts: coccicheck: Correct usage of make coccicheck
coccinelle: update expiring email addresses
coccinnelle: Remove ptr_ret script
kbuild: do not use scripts/ld-version.sh for checking spatch version
remove boolinit.cocci
Commit 64a1b95bb9 ("genirq: Restrict export of irq_to_desc()") removed
the export of irq_to_desc() unless powerpc KVM is being built, because
there is still a use of irq_to_desc() in modular code there.
However it used:
#ifdef CONFIG_KVM_BOOK3S_64_HV
Which doesn't work when that symbol is =m, leading to a build failure:
ERROR: modpost: "irq_to_desc" [arch/powerpc/kvm/kvm-hv.ko] undefined!
Fix it by checking for the definedness of the correct symbol which is
CONFIG_KVM_BOOK3S_64_HV_MODULE.
Fixes: 64a1b95bb9 ("genirq: Restrict export of irq_to_desc()")
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Pull misc vfs updates from Al Viro:
"Assorted patches from previous cycle(s)..."
* 'work.misc' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
fix hostfs_open() use of ->f_path.dentry
Make sure that make_create_in_sticky() never sees uninitialized value of dir_mode
fs: Kill DCACHE_DONTCACHE dentry even if DCACHE_REFERENCED is set
fs: Handle I_DONTCACHE in iput_final() instead of generic_drop_inode()
fs/namespace.c: WARN if mnt_count has become negative
Pull documentation fixes from Jonathan Corbet:
"A small set of late-arriving, small documentation fixes"
* tag 'docs-5.11-2' of git://git.lwn.net/linux:
docs: admin-guide: Fix default value of max_map_count in sysctl/vm.rst
Documentation/submitting-patches: Document the SoB chain
Documentation: process: Correct numbering
docs: submitting-patches: Trivial - fix grammatical error
Pull ext4 updates from Ted Ts'o:
"Various bug fixes and cleanups for ext4; no new features this cycle"
* tag 'ext4_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tytso/ext4: (29 commits)
ext4: remove unnecessary wbc parameter from ext4_bio_write_page
ext4: avoid s_mb_prefetch to be zero in individual scenarios
ext4: defer saving error info from atomic context
ext4: simplify ext4 error translation
ext4: move functions in super.c
ext4: make ext4_abort() use __ext4_error()
ext4: standardize error message in ext4_protect_reserved_inode()
ext4: remove redundant sb checksum recomputation
ext4: don't remount read-only with errors=continue on reboot
ext4: fix deadlock with fs freezing and EA inodes
jbd2: add a helper to find out number of fast commit blocks
ext4: make fast_commit.h byte identical with e2fsprogs/fast_commit.h
ext4: fix fall-through warnings for Clang
ext4: add docs about fast commit idempotence
ext4: remove the unused EXT4_CURRENT_REV macro
ext4: fix an IS_ERR() vs NULL check
ext4: check for invalid block size early when mounting a file system
ext4: fix a memory leak of ext4_free_data
ext4: delete nonsensical (commented-out) code inside ext4_xattr_block_set()
ext4: update ext4_data_block_valid related comments
...
