There is an issue that WCN6855 tries to connect to an AP using
a hardware rate of 1Mb/s , even though the AP has announced
expected rates as [24, 36, 48, 54] in Probe Response frame.
The reason is that WCN6855 firmware clears hardware rate info
of management frames when vdev starts and uses 1Mb/s as default.
To solve it, reconfigure the rate after vdev is started.
Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-01720.1-QCAHSPSWPL_V1_V2_SILICONZ_LITE-1
Signed-off-by: Baochen Qiang <quic_bqiang@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20220112025400.2222-1-quic_bqiang@quicinc.com
kmalloc_array()/kcalloc() should be used to avoid potential overflow when
a multiplication is needed to compute the size of the requested memory.
kmalloc_array() can be used here instead of kcalloc() because the array is
fully initialized in the next 'for' loop.
Finally, 'cd->detectors' is defined as 'struct pri_detector **detectors;'.
So 'cd->detectors' and '*cd->detectors' are both some pointer.
So use a more logical 'sizeof(*cd->detectors)'.
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/0fbcd32a0384ac1f87c5a3549e505e4becc60226.1640624216.git.christophe.jaillet@wanadoo.fr
platform_get_resource(pdev, IORESOURCE_IRQ, ..) relies on static
allocation of IRQ resources in DT core code, this causes an issue
when using hierarchical interrupt domains using "interrupts" property
in the node as this bypasses the hierarchical setup and messes up the
irq chaining.
In preparation for removal of static setup of IRQ resource from DT core
code use platform_get_irq().
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20211224192626.15843-8-prabhakar.mahadev-lad.rj@bp.renesas.com
The struct ath5k_hw member ah_txq_isr_txok_all is never reset/assigned
outside of ath5k_hw_get_isr() and with the used bitwise-or in the
interrupt handling accumulates all ever set interrupt flags.
Fix this by clearing ah_txq_isr_txok_all before assigning.
Patch tested with Senao NMP-8602 card
Qualcomm Atheros AR5413/AR5414 Wireless Network Adapter [AR5006X(S) 802.11abg] (rev 01)
ath5k: phy6: Atheros AR5413 chip found (MAC: 0xa4, PHY: 0x61)
running IBSS mode against Atheros (ath9k) card using
ping and iperf traffic.
Signed-off-by: Peter Seiderer <ps.report@gmx.net>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20220110223021.17655-5-ps.report@gmx.net
The bug was found during fuzzing. Stacktrace locates it in
ath5k_eeprom_convert_pcal_info_5111.
When none of the curve is selected in the loop, idx can go
up to AR5K_EEPROM_N_PD_CURVES. The line makes pd out of bound.
pd = &chinfo[pier].pd_curves[idx];
There are many OOB writes using pd later in the code. So I
added a sanity check for idx. Checks for other loops involving
AR5K_EEPROM_N_PD_CURVES are not needed as the loop index is not
used outside the loops.
The patch is NOT tested with real device.
The following is the fuzzing report
BUG: KASAN: slab-out-of-bounds in ath5k_eeprom_read_pcal_info_5111+0x126a/0x1390 [ath5k]
Write of size 1 at addr ffff8880174a4d60 by task modprobe/214
CPU: 0 PID: 214 Comm: modprobe Not tainted 5.6.0 #1
Call Trace:
dump_stack+0x76/0xa0
print_address_description.constprop.0+0x16/0x200
? ath5k_eeprom_read_pcal_info_5111+0x126a/0x1390 [ath5k]
? ath5k_eeprom_read_pcal_info_5111+0x126a/0x1390 [ath5k]
__kasan_report.cold+0x37/0x7c
? ath5k_eeprom_read_pcal_info_5111+0x126a/0x1390 [ath5k]
kasan_report+0xe/0x20
ath5k_eeprom_read_pcal_info_5111+0x126a/0x1390 [ath5k]
? apic_timer_interrupt+0xa/0x20
? ath5k_eeprom_init_11a_pcal_freq+0xbc0/0xbc0 [ath5k]
? ath5k_pci_eeprom_read+0x228/0x3c0 [ath5k]
ath5k_eeprom_init+0x2513/0x6290 [ath5k]
? ath5k_eeprom_init_11a_pcal_freq+0xbc0/0xbc0 [ath5k]
? usleep_range+0xb8/0x100
? apic_timer_interrupt+0xa/0x20
? ath5k_eeprom_read_pcal_info_2413+0x2f20/0x2f20 [ath5k]
ath5k_hw_init+0xb60/0x1970 [ath5k]
ath5k_init_ah+0x6fe/0x2530 [ath5k]
? kasprintf+0xa6/0xe0
? ath5k_stop+0x140/0x140 [ath5k]
? _dev_notice+0xf6/0xf6
? apic_timer_interrupt+0xa/0x20
ath5k_pci_probe.cold+0x29a/0x3d6 [ath5k]
? ath5k_pci_eeprom_read+0x3c0/0x3c0 [ath5k]
? mutex_lock+0x89/0xd0
? ath5k_pci_eeprom_read+0x3c0/0x3c0 [ath5k]
local_pci_probe+0xd3/0x160
pci_device_probe+0x23f/0x3e0
? pci_device_remove+0x280/0x280
? pci_device_remove+0x280/0x280
really_probe+0x209/0x5d0
Reported-by: Brendan Dolan-Gavitt <brendandg@nyu.edu>
Signed-off-by: Zekun Shen <bruceshenzk@gmail.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/YckvDdj3mtCkDRIt@a-10-27-26-18.dynapool.vpn.nyu.edu
When there is an error in peer create process from
ath11k_peer_find(), the code attempts to handle a fallback
for peer create. When this fallback fails, the driver returns
the fallback return code rather than actual error code
(-ENOENT). So refactor the fallback routine to return
the actual error code.
Tested-on: QCN9074 hw1.0 PCI WLAN.HK.2.5.0.1-01067-QCAHKSWPL_SILICONZ-1
Signed-off-by: Karthikeyan Periyasamy <periyasa@codeaurora.org>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/1640244819-21183-1-git-send-email-quic_periyasa@quicinc.com
Currently, ath11k_core_alloc() creates a single thread workqueue.
This workqueue is not detroyed during clean up when ath11k modules
are unloaded from the kernel and is left as it is.
If workqueue is not destroyed, it could lead to kernel
memory scarcity in a longer run. This could affect self and
other drivers workability as well.
Add destroy workqueue in ath11k_core_free().
Tested on: IPQ8074 WLAN.HK.2.4.0.1-01746-QCAHKSWPL_SILICONZ-1
Signed-off-by: Aditya Kumar Singh <quic_adisi@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/1640231787-17408-1-git-send-email-quic_adisi@quicinc.com
In function ath10k_wow_convert_8023_to_80211(), it will do memcpy for
the new->pattern, and currently the new->pattern and new->mask is same
with the old, then the memcpy of new->pattern will also overwrite the
old->pattern, because the header format of new->pattern is 802.11,
its length is larger than the old->pattern which is 802.3. Then the
operation of "Copy frame body" will copy a mistake value because the
body memory has been overwrite when memcpy the new->pattern.
Assign another empty value to new_pattern to avoid the overwrite issue.
Tested-on: QCA6174 hw3.2 SDIO WLAN.RMH.4.4.1-00049
Fixes: fa3440fa2f ("ath10k: convert wow pattern from 802.3 to 802.11")
Signed-off-by: Wen Gong <quic_wgong@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20211222031347.25463-1-quic_wgong@quicinc.com
Kees reports quoted commit introduced the following warning on arm64:
drivers/net/ethernet/allwinner/sun4i-emac.c:922:60: error: format '%x' expects argument of type 'unsigned int', but argument 3 has type 'resource_size_t' {aka 'long long unsigned int'} [-Werror=format=]
922 | netdev_info(ndev, "get io resource from device: 0x%x, size = %u\n",
| ~^
| | | unsigned int
| %llx
923 | regs->start, resource_size(regs));
| ~~~~~~~~~~~
| |
| resource_size_t {aka long long unsigned int}
.. and another one like that for resource_size().
Switch to %pa and a cast.
Reported-by: Kees Cook <keescook@chromium.org>
Fixes: 47869e82c8 ("sun4i-emac.c: add dma support")
Link: https://lore.kernel.org/r/20220108034438.2227343-1-kuba@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
As page_pool_refill_alloc_cache() is only called by
__page_pool_get_cached(), which assumes non-concurrent access
as suggested by the comment in __page_pool_get_cached(), and
ptr_ring allows concurrent access between consumer and producer,
so remove the spinlock in page_pool_refill_alloc_cache().
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Acked-by: Jesper Dangaard Brouer <brouer@redhat.com>
Link: https://lore.kernel.org/r/20220107090042.13605-1-linyunsheng@huawei.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Syzbot reported uninit value in mcs7830_bind(). The problem was in
missing validation check for bytes read via usbnet_read_cmd().
usbnet_read_cmd() internally calls usb_control_msg(), that returns
number of bytes read. Code should validate that requested number of bytes
was actually read.
So, this patch adds missing size validation check inside
mcs7830_get_reg() to prevent uninit value bugs
Reported-and-tested-by: syzbot+003c0a286b9af5412510@syzkaller.appspotmail.com
Fixes: 2a36d70834 ("USB: driver for mcs7830 (aka DeLOCK) USB ethernet adapter")
Signed-off-by: Pavel Skripkin <paskripkin@gmail.com>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Link: https://lore.kernel.org/r/20220106225716.7425-1-paskripkin@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Menglong Dong says:
====================
net: skb: introduce kfree_skb_with_reason()
In this series patch, the interface kfree_skb_with_reason() is
introduced(), which is used to collect skb drop reason, and pass
it to 'kfree_skb' tracepoint. Therefor, 'drop_monitor' or eBPF is
able to monitor abnormal skb with detail reason.
In fact, this series patches are out of the intelligence of David
and Steve, I'm just a truck man :/
Previous discussion is here:
https://lore.kernel.org/netdev/20211118105752.1d46e990@gandalf.local.home/https://lore.kernel.org/netdev/67b36bd8-2477-88ac-83a0-35a1eeaf40c9@gmail.com/
In the first patch, kfree_skb_with_reason() is introduced and
the 'reason' field is added to 'kfree_skb' tracepoint. In the
second patch, 'kfree_skb()' in replaced with 'kfree_skb_with_reason()'
in tcp_v4_rcv(). In the third patch, 'kfree_skb_with_reason()' is
used in __udp4_lib_rcv().
Changes since v3:
- fix some code style problems in skb.h
Changes since v2:
- rename kfree_skb_with_reason() to kfree_skb_reason()
- make kfree_skb() static inline, as Jakub suggested
Changes since v1:
- rename some drop reason, as David suggested
- add the third patch
====================
Link: https://lore.kernel.org/r/20220109063628.526990-1-imagedong@tencent.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Replace kfree_skb() with kfree_skb_reason() in __udp4_lib_rcv.
New drop reason 'SKB_DROP_REASON_UDP_CSUM' is added for udp csum
error.
Signed-off-by: Menglong Dong <imagedong@tencent.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Replace kfree_skb() with kfree_skb_reason() in tcp_v4_rcv(). Following
drop reasons are added:
SKB_DROP_REASON_NO_SOCKET
SKB_DROP_REASON_PKT_TOO_SMALL
SKB_DROP_REASON_TCP_CSUM
SKB_DROP_REASON_TCP_FILTER
After this patch, 'kfree_skb' event will print message like this:
$ TASK-PID CPU# ||||| TIMESTAMP FUNCTION
$ | | | ||||| | |
<idle>-0 [000] ..s1. 36.113438: kfree_skb: skbaddr=(____ptrval____) protocol=2048 location=(____ptrval____) reason: NO_SOCKET
The reason of skb drop is printed too.
Signed-off-by: Menglong Dong <imagedong@tencent.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Introduce the interface kfree_skb_reason(), which is able to pass
the reason why the skb is dropped to 'kfree_skb' tracepoint.
Add the 'reason' field to 'trace_kfree_skb', therefor user can get
more detail information about abnormal skb with 'drop_monitor' or
eBPF.
All drop reasons are defined in the enum 'skb_drop_reason', and
they will be print as string in 'kfree_skb' tracepoint in format
of 'reason: XXX'.
( Maybe the reasons should be defined in a uapi header file, so that
user space can use them? )
Signed-off-by: Menglong Dong <imagedong@tencent.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Build bot reports:
drivers/net/ethernet/mellanox/mlx5/core/en_stats.c: In function 'fec_set_block_stats':
drivers/net/ethernet/mellanox/mlx5/core/en_stats.c:1235:48: error: 'outl' undeclared (first use in this function); did you mean 'out'?
1235 | if (mlx5_core_access_reg(mdev, in, sz, outl, sz, MLX5_REG_PPCNT, 0, 0))
| ^~~~
| out
Reported-by: kernel test robot <lkp@intel.com>
Suggested-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Link: https://lore.kernel.org/r/20220109213321.2292830-1-kuba@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Michael Chan says:
====================
bnxt_en: Update for net-next
This series adds better error and debug logging for firmware messages.
We now also use the firmware provided timeout value for long running
commands instead of capping it to 40 seconds.
====================
Link: https://lore.kernel.org/r/1641772485-10421-1-git-send-email-michael.chan@broadcom.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
While it has always been possible to infer that an HWRM command was
abandoned due to an unhealthy firmware status by the shortened timeout
reported, this change improves the log messaging to account for this
case explicitly. In the interests of further clarity, the firmware
status is now also reported in these new messages.
v2: Remove inline keyword for hwrm_wait_must_abort() in .c file.
Reviewed-by: Andy Gospodarek <gospo@broadcom.com>
Signed-off-by: Edwin Peer <edwin.peer@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Some older devices cannot accommodate the 40 seconds timeout
cap for long running commands (such as NVRAM commands) due to
hardware limitations. Allow these devices to request more time for
these long running commands, but print a warning, since the longer
timeout may cause the hung task watchdog to trigger. In the case of a
firmware update operation, this is preferable to failing outright.
v2: Use bp->hwrm_cmd_max_timeout directly without the constants.
Fixes: 881d8353b0 ("bnxt_en: Add an upper bound for all firmware command timeouts.")
Signed-off-by: Edwin Peer <edwin.peer@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The current driver design relies on the PF netdev being open in order
to intercept the following HWRM commands from a VF:
- HWRM_FUNC_VF_CFG
- HWRM_CFA_L2_FILTER_ALLOC
- HWRM_PORT_PHY_QCFG (only if FW_CAP_LINK_ADMIN is not supported)
If the PF is closed, then VFs are subjected to rather inscrutable error
messages in response to any configuration requests involving the above
command types. Recent firmware distinguishes this problem case from
other errors by returning HWRM_ERR_CODE_PF_UNAVAILABLE. In most cases,
the appropriate course of action is still to fail, but this can now be
accomplished with the aid of more user informative log messages. For L2
filter allocations that are already asynchronous, an automatic retry
seems more appropriate.
v2: Delete extra newline.
Signed-off-by: Edwin Peer <edwin.peer@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Add logging of firmware messages. These can be useful for diagnosing
issues in the field, but due to their verbosity are only appropriate
at a debug message level.
Signed-off-by: Edwin Peer <edwin.peer@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
