To match the vendor's terminology, change #defines, identifiers, and
comments:
- mute/dim/hardware buttons are now called dim/mute
- mixer status/interrupt is now notify
- vol is now monitor
Signed-off-by: Geoffrey D. Bennett <g@b4.vu>
Link: https://lore.kernel.org/r/20210620164636.GA9199@m.b4.vu
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The per-model button_count value was used to determine whether
dim/mute controls should be added, but these are present iff
line_out_hw_vol is true. Remove button_count and replace with
SCARLETT2_BUTTON_MAX and a check for line_out_hw_vol true.
Signed-off-by: Geoffrey D. Bennett <g@b4.vu>
Link: https://lore.kernel.org/r/20210620164634.GA9193@m.b4.vu
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Just ignore instead of printing an error if the interrupt data is not
the expected length. This check was for development and the condition
has not been observed.
Signed-off-by: Geoffrey D. Bennett <g@b4.vu>
Link: https://lore.kernel.org/r/20210620164632.GA9186@m.b4.vu
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Asus Zenbook 14 UM431D has two speaker pins and a headphone pin, and
the auto-parser ends up assigning the bass to the third DAC 0x06.
Although the tone comes out, it's inconvenient because this DAC has no
volume control unlike two other DACs.
For obtaining the volume control for the bass speaker, this patch
enforces the mapping to let both front and bass speaker pins sharing
the same DAC. It's not ideal but a little bit of improvement.
Since we've already applied the same workaround for another ASUS
machine, we just need to hook the chain to the existing quirk.
BugLink: https://bugzilla.kernel.org/show_bug.cgi?id=212547
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20210620065952.18948-1-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
On HP Spectre x360 15-df0xxx, after system boot with plugged headset, the
headset mic are not detected.
Moving pincfg and DAC's config to single fixup function fix this.
[ The actual bug in the original code was that it used a chain to
ALC286_FIXUP_SPEAKER2_TO_DAC1, and it contains not only the DAC1
route fix but also another chain to ALC269_FIXUP_THINKPAD_ACPI.
I thought the latter one is harmless for non-Thinkpad, but it
doesn't seem so; it contains again yet another chain to
ALC269_FIXUP_SKI_IGNORE, and this might be bad for some machines,
including this HP machine. -- tiwai ]
Signed-off-by: Elia Devito <eliadevito@gmail.com>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20210619204105.5682-1-eliadevito@gmail.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
A user of FFADO project reported the issue of ToneWeal FW66. As a result,
the device is identified as one of applications of BeBoB solution.
I note that in the report the device returns contradictory result in plug
discovery process for audio subunit. Fortunately ALSA BeBoB driver doesn't
perform it thus it's likely to handle the device without issues.
I receive no reaction to test request for this patch yet, however it would
be worth to add support for it.
daniel@gibbonmoon:/sys/bus/firewire/devices/fw1$ grep -r . *
Binary file config_rom matches
dev:244:1
guid:0x0023270002000000
hardware_version:0x000002
is_local:0
model:0x020002
model_name:FW66
power/runtime_active_time:0
power/runtime_active_kids:0
power/runtime_usage:0
power/runtime_status:unsupported
power/async:disabled
power/runtime_suspended_time:0
power/runtime_enabled:disabled
power/control:auto
subsystem/drivers_autoprobe:1
uevent:MAJOR=244
uevent:MINOR=1
uevent:DEVNAME=fw1
units:0x00a02d:0x010001
vendor:0x002327
vendor_name:ToneWeal
fw1.0/uevent:MODALIAS=ieee1394:ven00002327mo00020002sp0000A02Dver00010001
fw1.0/power/runtime_active_time:0
fw1.0/power/runtime_active_kids:0
fw1.0/power/runtime_usage:0
fw1.0/power/runtime_status:unsupported
fw1.0/power/async:disabled
fw1.0/power/runtime_suspended_time:0
fw1.0/power/runtime_enabled:disabled
fw1.0/power/control:auto
fw1.0/model:0x020002
fw1.0/rom_index:15
fw1.0/specifier_id:0x00a02d
fw1.0/model_name:FW66
fw1.0/version:0x010001
fw1.0/modalias:ieee1394:ven00002327mo00020002sp0000A02Dver00010001
Cc: Daniel Jozsef <daniel.jozsef@gmail.com>
Reference: https://lore.kernel.org/alsa-devel/20200119164335.GA11974@workstation/
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Link: https://lore.kernel.org/r/20210619083922.16060-1-o-takashi@sakamocchi.jp
Signed-off-by: Takashi Iwai <tiwai@suse.de>
I assumed that the combination of packet formats for MOTU 828 mk3 Hybrid
is the same as MOTU 828 mk3 FireWire. However at higher sampling rate, it
is different. MOTU 828 mk3 Hybrid has additional 4 dummy data chunks for
rx packet.
This commit fixes the issue to which I address at a commit f2ac3b8395
("ALSA: firewire-motu: sequence replay for source packet header").
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Link: https://lore.kernel.org/r/20210618040713.114611-1-o-takashi@sakamocchi.jp
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Below devices reports zero as the number of channels for external output
plug with MIDI type:
* Yamaha GO44/GO46
* Terratec Phase 24/X24
As a result, rx packet format is invalid and they generate silent sound.
This is a regression added in v5.13.
This commit fixes the bug, addressed at a commit 1bd1b3be86 ("ALSA:
bebob: perform sequence replay for media clock recovery").
Cc: <stable@vger.kernel.org>
Fixes: 5c6ea94f2b ("ALSA: bebob: detect the number of available MIDI ports")
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Link: https://lore.kernel.org/r/20210618040447.113306-1-o-takashi@sakamocchi.jp
Signed-off-by: Takashi Iwai <tiwai@suse.de>
MOTU 896 is a second model in MOTU FireWire series, produced in 2001. This
model consists of three chips:
* Texas Instruments TSB41AB2 (Physical layer for IEEE 1394 bus)
* Philips Semiconductors PDI 1394L21BE (Link layer for IEEE 1394 bus and
packet processing layer)
* QuickLogic QuickRAM QL4016 (Data block processing layer and digital
signal processing)
This commit adds a support for the model, with its unique protocol as
version 1. The features of this protocol are:
* no MIDI support.
* Rx packets have no data chunks for control and status messages.
* Tx packets have 2 bytes for control and status messages in the end of
each data block.
* The most of settings are represented in bit flag in one quadlet address
(0x'ffff'f000'0b14).
* It's selectable to use signal on optical interface, however the device
has no register specific to it. The state has effect just to whether
to exclude differed data chunks.
* The internal multiplexer is not configured by software.
Just after powering on, the device has a quirk to fail handling
transaction. I recommend users to connect the device enough after powering
on.
$ python3 crpp < /sys/bus/firewire/devices/fw1/config_rom
ROM header and bus information block
-----------------------------------------------------------------
400 04102814 bus_info_length 4, crc_length 16, crc 10260
404 31333934 bus_name "1394"
408 20001000 irmc 0, cmc 0, isc 1, bmc 0, cyc_clk_acc 0, max_rec 1 (4)
40c 0001f200 company_id 0001f2 |
410 0000d645 device_id 000000d645 | EUI-64 0001f2000000d645
root directory
-----------------------------------------------------------------
414 0004c65c directory_length 4, crc 50780
418 030001f2 vendor
41c 0c0083c0 node capabilities per IEEE 1394
420 8d000006 --> eui-64 leaf at 438
424 d1000001 --> unit directory at 428
unit directory at 428
-----------------------------------------------------------------
428 0003ab34 directory_length 3, crc 43828
42c 120001f2 specifier id
430 13000002 version
434 17102801 model
eui-64 leaf at 438
-----------------------------------------------------------------
438 0002057d leaf_length 2, crc 1405
43c 0001f200 company_id 0001f2 |
440 0000d645 device_id 000000d645 | EUI-64 0001f2000000d645
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Link: https://lore.kernel.org/r/20210616082847.124688-3-o-takashi@sakamocchi.jp
Signed-off-by: Takashi Iwai <tiwai@suse.de>
MOTU 828 is a first model in MOTU FireWire series, produced in 2001. This
model consists of three chips:
* Texas Instruments TSB41AB1 (Physical layer for IEEE 1394 bus)
* Philips Semiconductors 1394L21BE (Link layer for IEEE 1394 bus and
packet processing layer)
* QuickLogic QuickRAM QL4016 (Data block processing layer and digital
signal processing)
This commit adds a support for this model, with its unique protocol as
version 1. The features of this protocol are:
* no MIDI support.
* Rx packets have no data chunks for control and status messages.
* Tx packets have 2 data chunks for control and status messages in the
end of each data block. The chunks consist of data block counter
(4 byte) and message (2 byte).
* All of settings are represented in bit flag in one quadlet address
(0x'ffff'f000'0b00).
* When optical interface is configured as S/PDIF, signals of the interface
is multiplexed for packets, instead of signals of coaxial interface.
* The internal multiplexer is not configured by software.
I note that the device has a quirk to mute output voluntarily during
receiving batch of packets in the beginning of packet streaming. The
operation to unmute should be done by software enough after the device
shifts the state, however it's not deterministic. Furthermore, just
after switching rate of sampling clock, the device keeps the state longer.
This patch manages to sleep 100 msec before unmute operation, but it may
fail to release the mute in the case that the rate is changed. As a
workaround, users can restart packet streaming at the same rate, or write
to specific register from userspace.
$ python3 crpp < /sys/bus/firewire/devices/fw1/config_rom
ROM header and bus information block
-----------------------------------------------------------------
400 04105c54 bus_info_length 4, crc_length 16, crc 23636
404 31333934 bus_name "1394"
408 20001000 irmc 0, cmc 0, isc 1, bmc 0, cyc_clk_acc 0, max_rec 1 (4)
40c 0001f200 company_id 0001f2 |
410 00005015 device_id 0000005015 | EUI-64 0001f20000005015
root directory
-----------------------------------------------------------------
414 0004c65c directory_length 4, crc 50780
418 030001f2 vendor
41c 0c0083c0 node capabilities per IEEE 1394
420 8d000006 --> eui-64 leaf at 438
424 d1000001 --> unit directory at 428
unit directory at 428
-----------------------------------------------------------------
428 00035052 directory_length 3, crc 20562
42c 120001f2 specifier id
430 13000001 version
434 17101800 model
eui-64 leaf at 438
-----------------------------------------------------------------
438 0002eeb6 leaf_length 2, crc 61110
43c 0001f200 company_id 0001f2 |
440 00005015 device_id 0000005015 | EUI-64 0001f20000005015
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Link: https://lore.kernel.org/r/20210616082847.124688-2-o-takashi@sakamocchi.jp
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The quirking bit-flags are currently set as contiguous integer enum values
and so currently SND_BEBOB_QUIRK_INITIAL_DISCONTINUOUS_DBC is zero and so
he quirking never getting set or tested correctly for this quirk. Fix this
by setting the quirking constants as shifted bit values.
Addresses-Coverity: ("Bitwise-and with zero")
Fixes: 93cd12d6e8 ("ALSA: bebob: code refactoring for model-dependent quirks")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Link: https://lore.kernel.org/r/20210615142048.59900-1-colin.king@canonical.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
sound/pci/trident/trident_memory.c: In function ‘set_tlb_bus’:
sound/pci/trident/trident_memory.c:85:35: error: ‘pagetr’ undeclared (first use in this function); did you mean ‘page’?
for (i = 0; i < UNIT_PAGES; i++, pagetr++) {
^~~~~~
page
Fixes: 74fb98311c ("ALSA: trident: Drop shadow TLB pointer table")
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Link: https://lore.kernel.org/r/20210612033458.42928-1-yuehaibing@huawei.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
In a commit c4d860a0d2 ("ALSA: bebob: loosen up severity of checking
continuity for BeBoB v3 quirk"), a workaround was added for the quirk in
BeBoB protocol version 3 against the discontinuity of data block counter.
As long as seeing with sequence replay for media clock recovery, such
quirk disappears.
This commit deletes the workaround.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Link: https://lore.kernel.org/r/20210611035003.26852-3-o-takashi@sakamocchi.jp
Signed-off-by: Takashi Iwai <tiwai@suse.de>
In a commit d3eabe939a ("ALSA: bebob: expand sleep just after breaking
connections for protocol version 1"), a workaround was added for a quirk
of freeze in BeBoB protocol version 1. As long as seeing with sequence
replay for media clock recovery, the quirk disappears.
This commit removes the workaround.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Link: https://lore.kernel.org/r/20210611035003.26852-2-o-takashi@sakamocchi.jp
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This provides support for Denon DN-X1600 hardware mixer.
The device itself supports 44100, 48000 and 96000 (Hz)
sample rates, but switching rates via software is currently not working.
Therefore, this patch hardcodes the sample rate to 48000Hz which
enables all 8 channels to function correctly when the correct
sample rate is selected on the hardware itself.
MIDI also tested and works.
Signed-off-by: Damien Zammit <damien@zamaudio.com>
Tested-by: xalmoxis@gmail.com
Link: https://lore.kernel.org/r/20210610083528.603942-2-damien@zamaudio.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The mmap of continuous pages and vmalloc'ed pages are relatively
easily done in a shot with the existing helper functions.
Implement the mmap ops for those types, so that the mmap works without
relying on the page fault handling.
Link: https://lore.kernel.org/r/20210609162551.7842-6-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This patch introduces the ops table to each memory allocation type
(SNDRV_DMA_TYPE_XXX) and abstract the handling for the better code
management. Then we get separate the page allocation, release and
other tasks for each type, especially for the SG buffer.
Each buffer type has now callbacks in the struct snd_malloc_ops, and
the common helper functions call those ops accordingly. The former
inline code that is specific to SG-buffer is moved into the local
sgbuf.c, and we can simplify the PCM code without details of memory
handling.
Link: https://lore.kernel.org/r/20210609162551.7842-4-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The shadow TLB pointer table is allocated and set up, but never really
used any longer by the driver. Let's drop it.
Since this is the only user of snd_pcm_sgbuf_get_ptr(), we can clean
up the API after this change.
Link: https://lore.kernel.org/r/20210609162551.7842-2-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
All of drivers in ALSA firewire stack processes two chances to process
isochronous packets in any isochronous context; in software IRQ context
for 1394 OHCI, and in process context of ALSA PCM application.
In the process context, callbacks of .pointer and .ack are utilized. The
callbacks are done by ALSA PCM core under acquiring lock of PCM substream,
In design of ALSA PCM core, call of snd_pcm_period_elapsed() is used for
drivers to awaken user processes from waiting for available frames. The
function voluntarily acquires lock of PCM substream, therefore it is not
called in the process context since it causes dead lock.
As a workaround to avoid the dead lock, all of drivers in ALSA firewire
stack uses workqueue to delegate the call. A variant of
snd_pcm_period_elapsed() without lock acquisition can obsolete the
workqueue.
An extra care is needed for the callback of .pointer since it's called
from snd_pcm_period_elapsed(). The isochronous context in Linux FireWire
subsystem is safe mostly for nested call except in software IRQ context.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Link: https://lore.kernel.org/r/20210610031733.56297-3-o-takashi@sakamocchi.jp
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Current implementation of ALSA PCM core has a kernel API,
snd_pcm_period_elapsed(), for drivers to queue event to awaken processes
from waiting for available frames. The function voluntarily acquires lock
of PCM substream, therefore it is not called in process context for any
PCM operation since the lock is already acquired.
It is convenient for packet-oriented driver, at least for drivers to audio
and music unit in IEEE 1394 bus. The drivers are allowed by Linux
FireWire subsystem to process isochronous packets queued till recent
isochronous cycle in process context in any time.
This commit adds snd_pcm_period_elapsed() variant,
snd_pcm_period_elapsed_without_lock(), for drivers to queue the event in
the process context.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Link: https://lore.kernel.org/r/20210610031733.56297-2-o-takashi@sakamocchi.jp
Signed-off-by: Takashi Iwai <tiwai@suse.de>
