NOA configuration take some amount of time to apply. That amount of
time depends on the size of the GT. There is no documented time for
this. For example, past experimentations with powergating
configuration changes seem to indicate a 60~70us delay. We go with
500us as default for now which should be over the required amount of
time (according to HW architects).
v2: Don't forget to save/restore registers used for the wait (Chris)
v3: Name used CS_GPR registers (Chris)
Fix compile issue due to rebase (Lionel)
v4: Fix save/restore helpers (Umesh)
v5: Move noa_wait from drm_i915_private to i915_perf_stream (Lionel)
v6: Add missing struct declarations in i915_perf.h
Signed-off-by: Lionel Landwerlin <lionel.g.landwerlin@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20191012072308.30312-2-chris@chris-wilson.co.uk
Here we introduce a mechanism by which the execbuf part of the i915
driver will be able to request that a batch buffer containing the
programming for a particular OA config be created.
We'll execute these OA configuration buffers right before executing a
set of userspace commands so that a particular user batchbuffer be
executed with a given OA configuration.
This mechanism essentially allows the userspace driver to go through
several OA configuration without having to open/close the i915/perf
stream.
v2: No need for locking on object OA config object creation (Chris)
Flush cpu mapping of OA config (Chris)
v3: Properly deal with the perf_metric lock (Chris/Lionel)
v4: Fix oa config unref/put when not found (Lionel)
v5: Allocate BOs for configurations on the stream instead of globally
(Lionel)
v6: Fix 64bit division (Chris)
v7: Store allocated config BOs into the stream (Lionel)
Signed-off-by: Lionel Landwerlin <lionel.g.landwerlin@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20191012072308.30312-1-chris@chris-wilson.co.uk
We set out-of-bound parameters inside the i915_requests.flags field,
such as disabling preemption or marking the end-of-context. We should
not coalesce consecutive requests if they have differing instructions
as we only inspect the last active request in a context. Thus if we
allow a later request to be merged into the same execution context, it
will mask any of the earlier flags.
References: 2a98f4e65b ("drm/i915: add infrastructure to hold off preemption on a request")
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Lionel Landwerlin <lionel.g.landwerlin@intel.com>
Reviewed-by: Lionel Landwerlin <lionel.g.landwerlin@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191011190325.10979-9-chris@chris-wilson.co.uk
We have a src and dect rectangle, use it instead of relying on
the core drm properties.
Because the core by default clips the src/dst properties, after
the drm_atomic_helper_check_plane_state() we manually set the
unclipped src/dst rectangles. We still need the call for
visibility checks, but this way we are able to use the src/dst
rects in the check/commit code.
This removes the special case in the watermark code for cursor w/h.
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191004113514.17064-5-maarten.lankhorst@linux.intel.com
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
[mlankhorst: Clarify commit message to state we use unclipped src/dst
This can all be done from the intel_update_crtc function. Split out the
pipe update into a separate function, just like is done for the planes.
Pull in all the changes done during fastset as well. It makes no sense
for it to still exist as a separate function.
Changes since v1:
- Inline intel_update_pipe_config()
Changes since v2:
- Add comments suggested by matt.
- Reorder commit_pipe_config() to remove all nesting. (Ville, Matt)
- Use intel_set_pipe_src_size((). (Matt)
Changes since v3:
- Move atomic_update_watermarks closer to the plane calls.
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191004113514.17064-7-maarten.lankhorst@linux.intel.com
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
[mlankhorst: Replace 8 spaces with tabs in comment]
Premature gamma lut prepration and loading which was getting
reflected in first modeset causing different colors on
screen during boot.
Issue: In BIOS, gamma is disabled by default. However, legacy read_luts()
was setting crtc_state->base.gamma_lut and gamma_lut was programmed
with junk values which led to visual artifacts (different
colored screens instead of usual black during boot).
Fix: Calling read_luts() only when gamma is enabled which will happen
after first modeset.
This fix is independent from the revert 1b8588741f ("Revert
"drm/i915/color: Extract icl_read_luts()"") and should fix different colors
on screen in legacy platforms too.
v2:
-Added gamma_enable checks inside read_luts() [Ville/Jani N]
-Corrected gamma enable check for CHV [Ville]
v3:
-Added check in ilk_read_luts() [Ville]
-Simplified gamma enable check for CHV [Ville]
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=111809
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=111885
Tested-by: Jani Saarinen <jani.saarinen@intel.com>
Signed-off-by: Swati Sharma <swati2.sharma@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191009065542.27415-2-swati2.sharma@intel.com
DC3CO is useful power state, when DMC detects PSR2 idle frame
while an active video playback, playing 30fps video on 60hz panel
is the classic example of this use case.
B.Specs:49196 has a restriction to enable DC3CO only for Video Playback.
It will be worthy to enable DC3CO after completion of each pageflip
and switch back to DC5 when display is idle because driver doesn't
differentiate between video playback and a normal pageflip.
We will use Frontbuffer flush call tgl_dc3co_flush() to enable DC3CO
state only for ORIGIN_FLIP flush call, because DC3CO state has primarily
targeted for VPB use case. We are not interested here for frontbuffer
invalidates calls because that triggers PSR2 exit, which will
explicitly disable DC3CO.
DC5 and DC6 saves more power, but can't be entered during video
playback because there are not enough idle frames in a row to meet
most PSR2 panel deep sleep entry requirement typically 4 frames.
As PSR2 existing implementation is using minimum 6 idle frames for
deep sleep, it is safer to enable DC5/6 after 6 idle frames
(By scheduling a delayed work of 6 idle frames, once DC3CO has been
enabled after a pageflip).
After manually waiting for 6 idle frames DC5/6 will be enabled and
PSR2 deep sleep idle frames will be restored to 6 idle frames, at this
point DMC will triggers DC5/6 once PSR2 enters to deep sleep after
6 idle frames.
In future when we will enable S/W PSR2 tracking, we can change the
PSR2 required deep sleep idle frames to 1 so DMC can trigger the
DC5/6 immediately after S/W manual waiting of 6 idle frames get
complete.
v2: calculated s/w state to switch over dc3co when there is an
update. [Imre]
Used cancel_delayed_work_sync() in order to avoid any race
with already scheduled delayed work. [Imre]
v3: Cancel_delayed_work_sync() may blocked the commit work.
hence dropping it, dc5_idle_thread() checks the valid wakeref before
putting the reference count, which avoids any chances of dropping
a zero wakeref. [Imre (IRC)]
v4: Used frontbuffer flush mechanism. [Imre]
v5: Used psr.pipe to extract frontbuffer busy bits. [Imre]
Used cancel_delayed_work_sync() in encoder disable path. [Imre]
Used mod_delayed_work() instead of cancelling and scheduling a
delayed work. [Imre]
Used psr.lock in tgl_dc5_idle_thread() to enable psr2 deep
sleep. [Imre]
Removed DC5_REQ_IDLE_FRAMES macro. [Imre]
v6: Used dc3co_exitline check instead of TGL and dc3co allowed_dc_mask
checks, used delayed_work_pending with the psr lock and removed the
psr2_deep_slp_disabled flag. [Imre]
v7: Code refactoring, moved most of functional code to inte_psr.c [Imre]
Using frontbuffer_bits on psr.pipe check instead of
busy_frontbuffer_bits. [Imre]
Calculating dc3co_exit_delay in intel_psr_enable_locked. [Imre]
Cc: Jani Nikula <jani.nikula@intel.com>
Cc: Imre Deak <imre.deak@intel.com>
Cc: Animesh Manna <animesh.manna@intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Anshuman Gupta <anshuman.gupta@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191003081738.22101-6-anshuman.gupta@intel.com
DC3CO enabling B.Specs sequence requires to enable end configure
exit scanlines to TRANS_EXITLINE register, programming this register
has to be part of modeset sequence as this can't be change when
transcoder or port is enabled.
When system boots with only eDP panel there may not be real
modeset as BIOS has already programmed the necessary registers,
therefore it needs to force a modeset to enable and configure
DC3CO exitline.
v1: Computing dc3co_exitline crtc state from a DP encoder
compute config. [Imre]
Enabling and disabling DC3CO PSR2 transcoder exitline from
encoder pre_enable and post_disable hooks. [Imre]
Computing dc3co_exitline instead of has_dc3co_exitline bool. [Imre]
v2: Code refactoring for symmetry and to avoid exported function. [Imre]
Removing IS_TIGERLAKE check from compute_config, adding PIPE_A
restriction and clearing dc3co_exitline state if crtc is not active
or it is not PSR2 capable in dc3co exitline compute_config. [Imre]
Using GEN >= 12 check in dc3co exitline get_config. [Imre]
Cc: Jani Nikula <jani.nikula@intel.com>
Cc: Imre Deak <imre.deak@intel.com>
Cc: Animesh Manna <animesh.manna@intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Anshuman Gupta <anshuman.gupta@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191003081738.22101-5-anshuman.gupta@intel.com
Add target_dc_state and used by set_target_dc_state API
in order to enable DC3CO state with existing DC states.
target_dc_state will enable/disable the desired DC state in
DC_STATE_EN reg when "DC Off" power well gets disable/enable.
v2: commit log improvement.
v3: Used intel_wait_for_register to wait for DC3CO exit. [Imre]
Used gen9_set_dc_state() to allow/disallow DC3CO. [Imre]
Moved transcoder psr2 exit line enablement from tgl_allow_dc3co()
to a appropriate place haswell_crtc_enable(). [Imre]
Changed the DC3CO power well enabled call back logic as
recommended in review comments. [Imre]
v4: Used wait_for_us() instead of intel_wait_for_reg(). [Imre (IRC)]
v5: using udelay() instead of waiting for DC3CO exit status.
v6: Fixed minor unwanted change.
v7: Removed DC3CO powerwell and POWER_DOMAIN_VIDEO.
v8: Uniform checks by using only target_dc_state instead of allowed_dc_mask
in "DC off" power well callback. [Imre]
Adding "DC off" power well id to older platforms. [Imre]
Removed psr2_deep_sleep flag from tgl_set_target_dc_state. [Imre]
v9: Used switch case for target DC state in
gen9_dc_off_power_well_disable(), checking DC3CO state against
allowed DC mask, using WARN_ON() in
tgl_set_target_dc_state(). [Imre]
v10: Code refactoring and using sanitize_target_dc_state(). [Imre]
Cc: Jani Nikula <jani.nikula@intel.com>
Cc: Imre Deak <imre.deak@intel.com>
Cc: Animesh Manna <animesh.manna@intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Anshuman Gupta <anshuman.gupta@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191003081738.22101-4-anshuman.gupta@intel.com
Adding following definition to i915_reg.h
1. DC_STATE_EN register DC3CO bit fields and masks.
DC3CO enable bit will be used by driver to make DC3CO
ready for DMC f/w and status bit will be used as DC3CO
entry status.
2. Transcoder EXITLINE register and its bit fields and mask.
Transcoder EXITLINE enable bit represents PSR2 idle frame
reset should be applied at exit line and exitlines mask
represent required number of scanlines at which DC3CO
exit happens.
B.Specs:49196
v1: Use of REG_BIT and using extra space for EXITLINE_ macro
definition. [Animesh]
v2: Grouping EXITLINE reg bits with EXITLINE(trans) define,
no functional change. [Ville]
Cc: Jani Nikula <jani.nikula@intel.com>
Cc: Imre Deak <imre.deak@intel.com>
Cc: Animesh Manna <animesh.manna@intel.com>
Reviewed-by: Animesh Manna <animesh.manna@intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Anshuman Gupta <anshuman.gupta@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191007094607.2111-1-anshuman.gupta@intel.com
