Add fsl,tuning-step for usdhc1 and usdhc2 to improve card compatibility.
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Default, state_100mhz and state_200mhz use the same settings. But current
kernel driver use these to indicate if sd3.0 support.
Add max-frequency for usdhc2 because board design limitation.
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The CSI-2 receivers in the i.MX8MP have 3 output channels. Specify this
in the device tree, to enable support for more than one channel.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add SOC special compatible string, remove fallback snps,dwc3 to let flatten
dwc3-layerscape driver to be probed and enable dma-coherence for usb node
since commit add layerscape dwc3 support, which set correct gsbustcfg0
value.
Add iommus property to run at old uboot, which use fixup add iommus by
check compatible string snsp,dwc3 compatible string.
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The same displays that can be connected directly to the
imx8mp-phyboard-pollux can also be connected to the expansion board
PEB-AV-10. For displays connected to the expansion board, a second LVDS
channel of the i.MX 8M Plus SoC is used and only a single display
connected to the SoC LVDS display bridge at a given time is supported.
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Yannic Moog <y.moog@phytec.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
An expansion board (PEB-AV-10) may be connected to the
imx8mp-phyboard-pollux. Its main purpose is to provide multimedia
interfaces, featuring a 3.5mm headphone jack, a USB-A port and LVDS as
well as backlight connectors.
Introduce the expansion board as dtsi, as it may be used standalone as
an expansion board, as well as in combination with display panels. These
display panels will include the dtsi.
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Yannic Moog <y.moog@phytec.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
imx8mp-phyboard-pollux had a display baked into its board dts file.
However this approach does not truly discribe the hardware and is not
suitable when using different displays.
Move display specific description into an overlay and add the successor
display for the phyboard-pollux as an additional overlay.
Reviewed-by: Teresa Remmet <t.remmet@phytec.de>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Yannic Moog <y.moog@phytec.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Change license from GPL-2.0 to GPL-2.0-or-later OR MIT.
Use syntax as defined in the SPDX standard. Also remove individual
authorship.
Acked-by: Teresa Remmet <t.remmet@phytec.de>
Signed-off-by: Yannic Moog <y.moog@phytec.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Describe the two SFP+ cages present on the LS1046AQDS board and their
associated I2C buses and GPIO lines.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Describe the two SFP+ cages found on the LX2160ARDB board with their
respective I2C buses and GPIO lines.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The QIXIS FPGA node is extended so that it describes the GPIO controller
responsible for all the status presence lines on both SFP+ cages as well
as the IO SLOTs present on the board.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Describe the FPGA present on the LX2160ARDB board as a simple-mfd I2C
device. The FPGA presents registers that deal with power-on-reset
timing, muxing, SFP cage monitoring and control etc.
Also add the two GPIO controllers responsible for monitoring and
controlling the SFP+ cages used for MAC5 and MAC6.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add devicetree for the Protonic PRT8ML.
The board is similar to the Protonic PRT8MM but i.MX8MP based.
Some features have been removed as the drivers haven't been mainlined
yet or other issues where encountered:
- Stepper motors to be controlled using motion control subsystem
- MIPI/DSI to eDP USB alt-mode
- Onboard T1 ethernet (10BASE-T1L+PoDL, 100BASE-T1+PoDL, 1000BASE-T1)
Signed-off-by: David Jander <david@protonic.nl>
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: Jonas Rebmann <jre@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Idle-inject up to 50% of all cpu's time in order to help cpufreq
to keep the temperature below the trip points.
Signed-off-by: Martin Kepplinger-Novaković <martink@posteo.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The thermal framework can use the cpu-idle-states as
described for imx8mp as an alternative or in parallel to
cpufreq.
Add the DT node to the cpu so the cooling devices will be present
and the thermal zone descriptions can use them.
Signed-off-by: Martin Kepplinger-Novaković <martink@posteo.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Disable Hysteresis Enable Field in pad ctl register for USB OC pin
as this is more appropriate for the signal form in our case.
Signed-off-by: Teresa Remmet <t.remmet@phytec.de>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
According to Documentation/devicetree/bindings/spi/spi-nxp-fspi.yaml,
imx93/imx95 should use it's own compatible string and fallback
compatible with imx8mm.
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Haibo Chen <haibo.chen@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add fan-supply regulator to pwm-fan node to specify power source.
Fixes: e3e8b199af ("arm64: dts: imx95: Add imx95-15x15-evk support")
Signed-off-by: Joy Zou <joy.zou@nxp.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
SDHC1 on the GW702x SOM routes to a connector for use on a baseboard
and as such are defined in the baseboard device-trees.
Remove it from the gw702x SOM device-tree.
Fixes: 0d5b288c21 ("arm64: dts: freescale: Add imx8mp-venice-gw7905-2x")
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
UART1 and UART3 go to a connector for use on a baseboard and as such are
defined in the baseboard device-trees. Remove them from the gw702x SOM
device-tree.
Fixes: 0d5b288c21 ("arm64: dts: freescale: Add imx8mp-venice-gw7905-2x")
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The SDHC1 interface is not used on the imx8mm-venice-gw72xx. Remove the
unused pinctrl_usdhc1 iomux node.
Fixes: 6f30b27c5e ("arm64: dts: imx8mm: Add Gateworks i.MX 8M Mini Development Kits")
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The i.MX8M Mini FEC RGMII tracelength is less than 1in and does not
require a x6 drive strength. Reduce the CLK drive strength to x1 for
lower emissions. Additionally since TXC is not a high frequency clock,
use slow slew rate (FSEL=0) for lower emmissions and improved signal
quality.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The i.MX8M Plus EQOS RGMII tracelength is less than 1in and does not
require a x6 drive strength. Reduce the CLK drive strength to x1 for
lower emissions. Additionally since TXC is not a high frequency clock,
use slow slew rate (FSEL=0) for lower emmissions and improved signal
quality.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Disable the unused refclk output for the TI DP83867 PHY used on
Gateworks Venice boards.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The board (micro)controller[1] is responsible for functions such as
power supply sequencing, SoC reset as well as serial/MAC address storage,
bootcount and scratch registers.
There is currently no Linux kernel driver for this controller, however,
there is a driver in U-Boot which utilises this binding.
[1] https://ten64doc.traverse.com.au/hardware/microcontroller/
Signed-off-by: Mathew McBride <matt@traverse.com.au>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Enable the HDMI output on the Debix SOM A board, using the HDMI encoder
present in the i.MX8MP SoC.
Enable and configure all nodes required for the HDMI port usage.
Signed-off-by: Kieran Bingham <kieran.bingham@ideasonboard.com>
Reviewed-by: Marco Felsch <m.felsch@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add USB vbus regulators to silence the following kernel warnings:
usb_phy_generic usbphynop1: dummy supplies not allowed for exclusive requests (id=vbus)
usb_phy_generic usbphynop2: dummy supplies not allowed for exclusive requests (id=vbus)
Because generic USB PHY driver requires exclusive vbus regulators since
commit 75fd6485cc ("usb: phy: generic: Get the vbus supply").
Signed-off-by: Primoz Fiser <primoz.fiser@norik.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add USB vbus regulators to silence the following kernel warnings:
usb_phy_generic usbphynop1: dummy supplies not allowed for exclusive requests (id=vbus)
usb_phy_generic usbphynop2: dummy supplies not allowed for exclusive requests (id=vbus)
Because generic USB PHY driver requires exclusive vbus regulators since
commit 75fd6485cc ("usb: phy: generic: Get the vbus supply").
Signed-off-by: Primoz Fiser <primoz.fiser@norik.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
This board is similar to the already upstream
imx8mp-skov-recv-tian-g07017.dts but uses a different 10" panel with a
different touch controller.
Signed-off-by: Steffen Trumtrar <s.trumtrar@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The mass production lx2160 rev2 use designware PCIe Controller. Old Rev1
which use mobivel PCIe controller was not supported. Although uboot
fixup can change compatible string fsl,lx2160a-pcie to fsl,ls2088a-pcie
since 2019, it is quite confused and should correctly reflect hardware
status in dtb. Change freescale's board to use rev2's dtsi firstly.
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Pull i2c fix from Wolfram Sang:
"One revert because of a regression in the I2C core which has sadly not
showed up during its time in -next"
* tag 'i2c-for-6.18-rc1-hotfix' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux:
Revert "i2c: boardinfo: Annotate code used in init phase only"
Pull irq fixes from Borislav Petkov:
- Skip interrupt ID 0 in sifive-plic during suspend/resume because
ID 0 is reserved and accessing reserved register space could result
in undefined behavior
- Fix a function's retval check in aspeed-scu-ic
* tag 'irq_urgent_for_v6.18_rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
irqchip/sifive-plic: Avoid interrupt ID 0 handling during suspend/resume
irqchip/aspeed-scu-ic: Fix an IS_ERR() vs NULL check
Pull tracing fixes from Steven Rostedt:
"The previous fix to trace_marker required updating trace_marker_raw as
well. The difference between trace_marker_raw from trace_marker is
that the raw version is for applications to write binary structures
directly into the ring buffer instead of writing ASCII strings. This
is for applications that will read the raw data from the ring buffer
and get the data structures directly. It's a bit quicker than using
the ASCII version.
Unfortunately, it appears that our test suite has several tests that
test writes to the trace_marker file, but lacks any tests to the
trace_marker_raw file (this needs to be remedied). Two issues came
about the update to the trace_marker_raw file that syzbot found:
- Fix tracing_mark_raw_write() to use per CPU buffer
The fix to use the per CPU buffer to copy from user space was
needed for both the trace_maker and trace_maker_raw file.
The fix for reading from user space into per CPU buffers properly
fixed the trace_marker write function, but the trace_marker_raw
file wasn't fixed properly. The user space data was correctly
written into the per CPU buffer, but the code that wrote into the
ring buffer still used the user space pointer and not the per CPU
buffer that had the user space data already written.
- Stop the fortify string warning from writing into trace_marker_raw
After converting the copy_from_user_nofault() into a memcpy(),
another issue appeared. As writes to the trace_marker_raw expects
binary data, the first entry is a 4 byte identifier. The entry
structure is defined as:
struct {
struct trace_entry ent;
int id;
char buf[];
};
The size of this structure is reserved on the ring buffer with:
size = sizeof(*entry) + cnt;
Then it is copied from the buffer into the ring buffer with:
memcpy(&entry->id, buf, cnt);
This use to be a copy_from_user_nofault(), but now converting it to
a memcpy() triggers the fortify-string code, and causes a warning.
The allocated space is actually more than what is copied, as the
cnt used also includes the entry->id portion. Allocating
sizeof(*entry) plus cnt is actually allocating 4 bytes more than
what is needed.
Change the size function to:
size = struct_size(entry, buf, cnt - sizeof(entry->id));
And update the memcpy() to unsafe_memcpy()"
* tag 'trace-v6.18-3' of git://git.kernel.org/pub/scm/linux/kernel/git/trace/linux-trace:
tracing: Stop fortify-string from warning in tracing_mark_raw_write()
tracing: Fix tracing_mark_raw_write() to use buf and not ubuf
Pull Kbuild fixes from Nathan Chancellor:
- Fix UAPI types check in headers_check.pl
- Only enable -Werror for hostprogs with CONFIG_WERROR / W=e
- Ignore fsync() error when output of gen_init_cpio is a pipe
- Several little build fixes for recent modules.builtin.modinfo series
* tag 'kbuild-fixes-6.18-1' of git://git.kernel.org/pub/scm/linux/kernel/git/kbuild/linux:
kbuild: Use '--strip-unneeded-symbol' for removing module device table symbols
s390/vmlinux.lds.S: Move .vmlinux.info to end of allocatable sections
kbuild: Add '.rel.*' strip pattern for vmlinux
kbuild: Restore pattern to avoid stripping .rela.dyn from vmlinux
gen_init_cpio: Ignore fsync() returning EINVAL on pipes
scripts/Makefile.extrawarn: Respect CONFIG_WERROR / W=e for hostprogs
kbuild: uapi: Strip comments before size type check
Pull SCSI fixes from James Bottomley:
"Fixes only in drivers (ufs, mvsas, qla2xxx, target) that came in just
before or during the merge window.
The most important one is the qla2xxx which reverts a conversion to
fix flexible array member warnings, that went up in this merge window
but which turned out on further testing to be causing data corruption"
* tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
scsi: ufs: core: Include UTP error in INT_FATAL_ERRORS
scsi: ufs: sysfs: Make HID attributes visible
scsi: mvsas: Fix use-after-free bugs in mvs_work_queue
scsi: ufs: core: Fix PM QoS mutex initialization
scsi: ufs: core: Fix runtime suspend error deadlock
Revert "scsi: qla2xxx: Fix memcpy() field-spanning write issue"
scsi: target: target_core_configfs: Add length check to avoid buffer overflow
Pull more x86 updates from Borislav Petkov:
- Remove a bunch of asm implementing condition flags testing in KVM's
emulator in favor of int3_emulate_jcc() which is written in C
- Replace KVM fastops with C-based stubs which avoids problems with the
fastop infra related to latter not adhering to the C ABI due to their
special calling convention and, more importantly, bypassing compiler
control-flow integrity checking because they're written in asm
- Remove wrongly used static branches and other ugliness accumulated
over time in hyperv's hypercall implementation with a proper static
function call to the correct hypervisor call variant
- Add some fixes and modifications to allow running FRED-enabled
kernels in KVM even on non-FRED hardware
- Add kCFI improvements like validating indirect calls and prepare for
enabling kCFI with GCC. Add cmdline params documentation and other
code cleanups
- Use the single-byte 0xd6 insn as the official #UD single-byte
undefined opcode instruction as agreed upon by both x86 vendors
- Other smaller cleanups and touchups all over the place
* tag 'x86_core_for_v6.18_rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (24 commits)
x86,retpoline: Optimize patch_retpoline()
x86,ibt: Use UDB instead of 0xEA
x86/cfi: Remove __noinitretpoline and __noretpoline
x86/cfi: Add "debug" option to "cfi=" bootparam
x86/cfi: Standardize on common "CFI:" prefix for CFI reports
x86/cfi: Document the "cfi=" bootparam options
x86/traps: Clarify KCFI instruction layout
compiler_types.h: Move __nocfi out of compiler-specific header
objtool: Validate kCFI calls
x86/fred: KVM: VMX: Always use FRED for IRQs when CONFIG_X86_FRED=y
x86/fred: Play nice with invoking asm_fred_entry_from_kvm() on non-FRED hardware
x86/fred: Install system vector handlers even if FRED isn't fully enabled
x86/hyperv: Use direct call to hypercall-page
x86/hyperv: Clean up hv_do_hypercall()
KVM: x86: Remove fastops
KVM: x86: Convert em_salc() to C
KVM: x86: Introduce EM_ASM_3WCL
KVM: x86: Introduce EM_ASM_1SRC2
KVM: x86: Introduce EM_ASM_2CL
KVM: x86: Introduce EM_ASM_2W
...
Pull x86 cleanups from Borislav Petkov:
- Simplify inline asm flag output operands now that the minimum
compiler version supports the =@ccCOND syntax
- Remove a bunch of AS_* Kconfig symbols which detect assembler support
for various instruction mnemonics now that the minimum assembler
version supports them all
- The usual cleanups all over the place
* tag 'x86_cleanups_for_v6.18_rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/asm: Remove code depending on __GCC_ASM_FLAG_OUTPUTS__
x86/sgx: Use ENCLS mnemonic in <kernel/cpu/sgx/encls.h>
x86/mtrr: Remove license boilerplate text with bad FSF address
x86/asm: Use RDPKRU and WRPKRU mnemonics in <asm/special_insns.h>
x86/idle: Use MONITORX and MWAITX mnemonics in <asm/mwait.h>
x86/entry/fred: Push __KERNEL_CS directly
x86/kconfig: Remove CONFIG_AS_AVX512
crypto: x86 - Remove CONFIG_AS_VPCLMULQDQ
crypto: X86 - Remove CONFIG_AS_VAES
crypto: x86 - Remove CONFIG_AS_GFNI
x86/kconfig: Drop unused and needless config X86_64_SMP
Pull slab fix from Vlastimil Babka:
"A NULL pointer deref hotfix"
* tag 'slab-for-6.18-rc1-hotfix' of git://git.kernel.org/pub/scm/linux/kernel/git/vbabka/slab:
slab: fix barn NULL pointer dereference on memoryless nodes
