The drm_gpusvm_for_each_notifier, drm_gpusvm_for_each_notifier_safe and
drm_gpusvm_for_each_range_safe macros are useful for locating notifiers
and ranges within a user-specified range. By making these macros public,
we enable broader access and utility for developers who need to leverage
them in their implementations.
v2 (Matthew Brost)
- drop inline __drm_gpusvm_range_find
- /s/notifier_iter_first/drm_gpusvm_notifier_find
Signed-off-by: Himal Prasad Ghimiray <himal.prasad.ghimiray@intel.com>
Reviewed-by: Matthew Brost <matthew.brost@intel.com>
Signed-off-by: Matthew Brost <matthew.brost@intel.com>
Link: https://lore.kernel.org/r/20250819162058.2777306-5-himal.prasad.ghimiray@intel.com
Detecting the monitor for DisplayPort targets is more complicated than
just reading the HPD pin level: it requires reading the DPCD in order to
check what kind of device is attached to the port and whether there is
an actual display attached.
In order to let DRM framework handle such configurations, disable
DRM_BRIDGE_OP_DETECT for dp-connector devices, letting the actual DP
driver perform detection. This still keeps DRM_BRIDGE_OP_HPD enabled, so
it is valid for the bridge to report HPD events.
Currently inside the kernel there are only two targets which list
hpd-gpios for dp-connector devices: arm64/qcom/qcs6490-rb3gen2 and
arm64/qcom/sa8295p-adp. Both should be fine with this change.
Cc: Bjorn Andersson <andersson@kernel.org>
Cc: Konrad Dybcio <konradybcio@kernel.org>
Cc: linux-arm-msm@vger.kernel.org
Acked-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Link: https://lore.kernel.org/r/20250802-dp-conn-no-detect-v1-1-2748c2b946da@oss.qualcomm.com
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
As the FLUSH_MEM and FLUSH_PT MMU_AS commands are deprecated in GPUs
from Mali-Gx20 onwards, this patch adds support for performing cache
maintenance via the FLUSH_CACHES command in GPU_COMMAND in place of
FLUSH_MEM and FLUSH_PT commands.
Mali-Gx10 and Mali-Gx15 GPUs also has support for the FLUSH_CACHES
command and will also use this by default going forward.
Reviewed-by: Steven Price <steven.price@arm.com>
Reviewed-by: Chia-I Wu <olvaffe@gmail.com>
Reviewed-by: Liviu Dudau <liviu.dudau@arm.com>
Signed-off-by: Karunika Choo <karunika.choo@arm.com>
Signed-off-by: Steven Price <steven.price@arm.com>
Link: https://lore.kernel.org/r/20250807162633.3666310-7-karunika.choo@arm.com
Mali-Gx15 introduces a new GPU_FEATURES register that provides
information about GPU-wide supported features. The register value will
be passed on to userspace via gpu_info.
Additionally, Mali-Gx15 presents an 'Immortalis' naming variant
depending on the shader core count and presence of Ray Intersection
feature support.
This patch adds:
- support for correctly identifying the model names for Mali-Gx15 GPUs.
- arch 11.8 FW binary support
Reviewed-by: Steven Price <steven.price@arm.com>
Reviewed-by: Chia-I Wu <olvaffe@gmail.com>
Reviewed-by: Liviu Dudau <liviu.dudau@arm.com>
Signed-off-by: Karunika Choo <karunika.choo@arm.com>
Signed-off-by: Steven Price <steven.price@arm.com>
Link: https://lore.kernel.org/r/20250807162633.3666310-5-karunika.choo@arm.com
This patch introduces panthor_hw and moves the initialization of the
gpu_info struct into panthor_hw.c in preparation of handling future GPU
register and naming changes.
Future GPU support can be added by extending panthor_gpu_info_init()
with the necessary register reads behind GPU architecture version guards
if the change is minor. For more complex changes, the function can be
forked and the appropriate function will need to be called based on the
GPU architecture version.
Reviewed-by: Steven Price <steven.price@arm.com>
Reviewed-by: Chia-I Wu <olvaffe@gmail.com>
Reviewed-by: Liviu Dudau <liviu.dudau@arm.com>
Signed-off-by: Karunika Choo <karunika.choo@arm.com>
Signed-off-by: Steven Price <steven.price@arm.com>
Link: https://lore.kernel.org/r/20250807162633.3666310-2-karunika.choo@arm.com
Create mipi_dsi_dcs_read_multi(), which accepts a mipi_dsi_multi_context
struct for improved error handling and cleaner panel driver code.
Create mipi_dsi_dcs_write_var_seq_multi() and
mipi_dsi_generic_write_var_seq_multi() macros which allow MIPI panel
drivers to write non-constant data to display controllers.
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Brigham Campbell <me@brighamcampbell.com>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Link: https://lore.kernel.org/r/20250731032343.1258366-3-me@brighamcampbell.com
The driver currently expects the pixel clock and the HS clock to be
compatible, but the DPHY PLL doesn't give very finely grained rates.
This often leads to the situation where the pipeline just fails, as the
resulting HS clock is just too off.
We could change the driver to do a better job on adjusting the DSI
blanking values, hopefully getting a working pipeline even if the pclk
and HS clocks are not exactly compatible. But that is a bigger work.
What we can do easily is to see in .atomic_check() what HS clock rate we
can get, based on the pixel clock rate, and then convert the HS clock
rate back to pixel clock rate and ask that rate from the crtc. If the
crtc has a good PLL (which is the case for TI K3 SoCs), this will fix
any issues wrt. the clock rates.
If the crtc cannot provide the requested clock, well, we're no worse off
with this patch than what we have at the moment.
Tested-by: Parth Pancholi <parth.pancholi@toradex.com>
Tested-by: Jayesh Choudhary <j-choudhary@ti.com>
Reviewed-by: Devarsh Thakkar <devarsht@ti.com>
Link: https://lore.kernel.org/r/20250723-cdns-dsi-impro-v5-14-e61cc06074c2@ideasonboard.com
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
The driver tries to calculate the value for REG_WAKEUP_TIME. However,
the calculation itself is not correct, and to add on it, the resulting
value is almost always larger than the field's size, so the actual
result is more or less random.
According to the docs, figuring out the value for REG_WAKEUP_TIME
requires HW characterization and there's no way to have a generic
algorithm to come up with the value. That doesn't help at all...
However, we know that the value must be smaller than the line time, and,
at least in my understanding, the proper value for it is quite small.
Testing shows that setting it to 1/10 of the line time seems to work
well. All video modes from my HDMI monitor work with this algorithm.
Hopefully we'll get more information on how to calculate the value, and
we can then update this.
Tested-by: Parth Pancholi <parth.pancholi@toradex.com>
Tested-by: Jayesh Choudhary <j-choudhary@ti.com>
Reviewed-by: Devarsh Thakkar <devarsht@ti.com>
Link: https://lore.kernel.org/r/20250723-cdns-dsi-impro-v5-11-e61cc06074c2@ideasonboard.com
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
cdns_dsi_adjust_phy_config() is called from cdns_dsi_check_conf(), which
is called from .atomic_check(). It checks the DSI htotal and adjusts it
to align on the DSI lane boundary by changing hfp and then recalculating
htotal and HS clock rate.
This has a few problems.
First is the fact that the whole thing is not needed: we do not need to
align on the lane boundary. The whole frame is sent in HS mode, and it
is fine if the line's last byte clock tick fills, say, only 2 of the 4
lanes. The next line will just continue from there. Assuming the
DSI timing values have been calculated to match the incoming DPI stream,
and the HS clock is compatible with the DPI pixel clock, the "uneven"
DSI lines will even out when multiple lines are being sent.
But we could do the align, aligning is not a problem as such. However,
adding more bytes to the hfp, as the function currently does, makes the
DSI line time longer, so the function then adjusts the HS clock rate.
This is where things fail: we don't know what rates we can get from the
HS clock, and at least in TI K3 SoC case the rates are quite coarsely
grained. Thus small adjustment to hfp will lead to a big change in HS
clock rate, and things break down.
We could do a loop here, adjusting hfp, adjusting clock, checking clock
rate, adjusting hfp again, etc., but considering that the whole
adjustment shouldn't be needed at all, it's easier to just remove the
function.
Something like this function should be added back later, when adding
burst mode support, but that's a bigger change and I don't think this
function would help that work in any way.
Tested-by: Parth Pancholi <parth.pancholi@toradex.com>
Tested-by: Jayesh Choudhary <j-choudhary@ti.com>
Reviewed-by: Devarsh Thakkar <devarsht@ti.com>
Link: https://lore.kernel.org/r/20250723-cdns-dsi-impro-v5-9-e61cc06074c2@ideasonboard.com
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
The driver checks if "DPI(HFP) > DSI(HSS+HSA+HSE+HBP)", and rejects the
mode if not.
However, testing shows that this doesn't hold at all. I can set the hfp
to very small values, with no errors. The feedback from the HW team also
was that the check is not right, although it's not clear if there's a
way to validate the FIFO emptying.
The check rejects quite a lot of modes, apparently for no good reason,
so drop the check.
Tested-by: Parth Pancholi <parth.pancholi@toradex.com>
Tested-by: Jayesh Choudhary <j-choudhary@ti.com>
Reviewed-by: Devarsh Thakkar <devarsht@ti.com>
Link: https://lore.kernel.org/r/20250723-cdns-dsi-impro-v5-6-e61cc06074c2@ideasonboard.com
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
This is inteded to address concerns that users might get cryptic error
messages or a failure to boot if they set nouveau.config=NvGspRm=0 on
the kernel command line and their gpu requires gsp (Ada or newer).
With this patch, that configuration results in error messages like this:
nouveau 0000:01:00.0: gsp: Failed to load required firmware for device.
nouveau 0000:01:00.0: gsp ctor failed: -22
nouveau 0000:01:00.0: probe with driver nouveau failed with error -22
When nouveau fails to load like this, we still fall back to the generic
framebuffer device, so users will still have limited graphical output.
Signed-off-by: Mel Henning <mhenning@darkrefraction.com>
Signed-off-by: Lyude Paul <lyude@redhat.com>
Link: https://lore.kernel.org/r/20250811213843.4294-4-mhenning@darkrefraction.com
This option was originally intoduced because the GSP code path was
not well tested and we wanted to leave it up to distros which code path
they shipped by default. By now though, the GSP path is probably better
tested than the old firmware eg. Fedora ships GSP by default and we
generally run CTS on GSP. We've always been GSP-only on Ada and later.
So, this path removes the option and effectively sets the option to
always on. We still fall back to the old firmware if GSP is not found.
This change only affects Turing and Ampere.
Users can still set nouveau.config=NvGspRm=0 on the kernel command line
to force using the old firmware on Turing/Ampere.
Signed-off-by: Mel Henning <mhenning@darkrefraction.com>
Reviewed-by: Ben Skeggs <bskeggs@nvidia.com>
Signed-off-by: Lyude Paul <lyude@redhat.com>
Link: https://lore.kernel.org/r/20250811213843.4294-2-mhenning@darkrefraction.com
Always set the RMDevidCheckIgnore registry key for GSP-RM so that it
will continue support newer variants of already supported GPUs.
GSP-RM maintains an internal list of PCI IDs of GPUs that it supports,
and checks if the current GPU is on this list. While the actual GPU
architecture (as specified in the BOOT_0/BOOT_42 registers) determines
how to enable the GPU, the PCI ID is used for the product name, e.g.
"NVIDIA GeForce RTX 5090".
Unfortunately, if there is no match, GSP-RM will refuse to initialize,
even if the device is fully supported. Nouveau will get an error
return code, but by then it's too late. This behavior may be corrected
in a future version of GSP-RM, but that does not help Nouveau today.
Fortunately, GSP-RM supports an undocumented registry key that tells it
to ignore the mismatch. In such cases, the product name returned will
be a blank string, but otherwise GSP-RM will continue.
Unlike Nvidia's proprietary driver, Nouveau cannot update to newer
firmware versions to keep up with every new hardware release. Instead,
we can permanently set this registry key, and GSP-RM will continue
to function the same with known hardware.
Signed-off-by: Timur Tabi <ttabi@nvidia.com>
Link: https://lore.kernel.org/r/20250808191340.1701983-1-ttabi@nvidia.com
Signed-off-by: Danilo Krummrich <dakr@kernel.org>
Use DRM's shadow-plane helper to map and access the GEM object's buffer
within kernel address space. Encapsulates the vmap logic in the GEM-DMA
helpers.
The sharp-memory driver currently reads the vaddr field from the GME
buffer object directly. This only works because GEM code 'automagically'
sets vaddr.
Shadow-plane helpers perform the same steps, but with correct abstraction
behind drm_gem_vmap(). The shadow-plane state provides the buffer address
in kernel address space and the format-conversion state.
v2:
- fix typo in commit description
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Reviewed-by: Javier Martinez Canillas <javierm@redhat.com>
Link: https://lore.kernel.org/r/20250627152327.8244-1-tzimmermann@suse.de
Use DRM's shadow-plane helper to map and access the GEM object's buffer
within kernel address space. Encapsulates the vmap logic in the GEM-DMA
helpers.
The repaper driver currently reads the vaddr field from the GME buffer
object directly. This only works because GEM code 'automagically' sets
vaddr.
Shadow-plane helpers perform the same steps, but with correct abstraction
behind drm_gem_vmap(). The shadow-plane state provides the buffer address
in kernel address space and the format-conversion state.
v2:
- fix typo in commit description
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Reviewed-by: Javier Martinez Canillas <javierm@redhat.com>
Link: https://lore.kernel.org/r/20250627152422.8399-1-tzimmermann@suse.de
The debug logging in gud_disconnect() adds zero detail and is
unnecessary, as it only prints the function name.
The same functionality can be achieved by using ftrace, and is
highlighted by checkpatch, stating the same.
This patch removes the debug log in the gud_disconnect() function.
Signed-off-by: Ruben Wauters <rubenru09@aol.com>
Reviewed-by: Thomas Zimmermann <tzimmermann@suse.de>
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Link: https://lore.kernel.org/r/20250721232210.12578-1-rubenru09@aol.com
