Fix the following DT schema check warning:
./Documentation/devicetree/bindings/pinctrl/cix,sky1-pinctrl.yaml:68:1: [warning] too many blank lines (2 > 1) (empty-lines)
One newline is enough. No functional change.
Signed-off-by: Marek Vasut <marex@nabladev.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Document Airoha AN7583 Pin Controller based on Airoha EN7581 with some
minor difference on some function group (PCM and LED gpio).
To not bloat the EN7581 schema with massive if condition, use a
dedicated YAML schema for Airoha AN7583.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Reviewed-by: Conor Dooley <conor.dooley@microchip.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Samsung pinctrl drivers changes for v6.19
Add pin controller support for Samsung Exynos8890 and Axis ARTPEC-9
SoCs. The latter is a newer design of Artpec SoCs made/designed by
Samsung, thus it shares most of the core blocks with Samsung Exynos,
including the pinctrl.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Convert the sprd,sc9860-pinctrl binding to DT schema format. What's
valid for the the sleep mode child nodes wasn't well defined. The schema
is based on the example (as there's no .dts with pin states) and the
driver's register definitions.
Signed-off-by: Rob Herring (Arm) <robh@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Document the support of the I/O synchronization parameters:
- skew-delay-input-ps;
- skew-delay-output-ps;
- st,io-sync.
Forbid 'skew-delay-input-ps' and 'skew-delay-output-ps' to be both
present on the same pin.
Allow the new properties only with compatibles that support them.
Add an example that uses the new properties.
Co-developed-by: Fabien Dessenne <fabien.dessenne@foss.st.com>
Signed-off-by: Fabien Dessenne <fabien.dessenne@foss.st.com>
Signed-off-by: Antonio Borneo <antonio.borneo@foss.st.com>
Reviewed-by: Conor Dooley <conor.dooley@microchip.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Add the properties 'skew-delay-input-ps' and 'skew-delay-output-ps'
to specify independent skew delay value for the two pin's directions.
Make the new properties unavailable when the existing property
'skew-delay' is selected.
Signed-off-by: Antonio Borneo <antonio.borneo@foss.st.com>
Acked-by: Conor Dooley <conor.dooley@microchip.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The pin-controller is used to control the Soc pins.
There are two pin-controllers on Cix Sky1 platform.
One is used under S0 state, the other is used under
S0 and S5 state.
Signed-off-by: Gary Yang <gary.yang@cixtech.com>
Reviewed-by: Conor Dooley <conor.dooley@microchip.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
On Polarfire SoC, iomux0 is responsible for routing functions to either
Multiprocessor Subsystem (MSS) IOs or to the FPGA fabric, where they
can either interface with custom RTL or be routed to the FPGA fabric's
IOs. Document it.
Reviewed-by: Rob Herring (Arm) <robh@kernel.org>
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The pic64gx has a second pinmux "downstream" of the iomux0 pinmux. The
documentation for the SoC provides no name for this device, but it is
used to swap pins between either GPIO controller #2 or select other
functions, hence the "gpio2" name. Currently there is no documentation
about what each bit actually does that is publicly available, nor (I
believe) what pins are affected. That info is as follows:
pin role (1/0)
--- ----------
E14 MAC_0_MDC/GPIO_2_0
E15 MAC_0_MDIO/GPIO_2_1
F16 MAC_1_MDC/GPIO_2_2
F17 MAC_1_MDIO/GPIO_2_3
D19 SPI_0_CLK/GPIO_2_4
B18 SPI_0_SS0/GPIO_2_5
B10 CAN_0_RXBUS/GPIO_2_6
C14 PCIE_PERST_2#/GPIO_2_7
E18 PCIE_WAKE#/GPIO_2_8
D18 PCIE_PERST_1#/GPIO_2_9
E19 SPI_0_DO/GPIO_2_10
C7 SPI_0_DI/GPIO_2_11
D6 QSPI_SS0/GPIO_2_12
D7 QSPI_CLK (B)/GPIO_2_13
C9 QSPI_DATA0/GPIO_2_14
C10 QSPI_DATA1/GPIO_2_15
A5 QSPI_DATA2/GPIO_2_16
A6 QSPI_DATA3/GPIO_2_17
D8 MMUART_3_RXD/GPIO_2_18
D9 MMUART_3_TXD/GPIO_2_19
B8 MMUART_4_RXD/GPIO_2_20
A8 MMUART_4_TXD/GPIO_2_21
C12 CAN_1_TXBUS/GPIO_2_22
B12 CAN_1_RXBUS/GPIO_2_23
A11 CAN_0_TX_EBL_N/GPIO_2_24
A10 CAN_1_TX_EBL_N/GPIO_2_25
D11 MMUART_2_RXD/GPIO_2_26
C11 MMUART_2_TXD/GPIO_2_27
B9 CAN_0_TXBUS/GPIO_2_28
Reviewed-by: Rob Herring (Arm) <robh@kernel.org>
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
mpfs pinctrl binding base
The pinctrl binding patch for iomux0 mpfs adds a ref to itself to the
syscon/mfd mss-top-sysreg binding, and therefore needs that file to
exist.
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
"mss-top-sysreg" contains clocks, pinctrl, resets, an interrupt controller
and more. At this point, only the reset controller child is described as
that's all that is described by the existing bindings.
The clock controller already has a dedicated node, and will retain it as
there are other clock regions, so like the mailbox, a compatible-based
lookup of the syscon is sufficient to keep the clock driver working as
before, so no child is needed. There's also an interrupt multiplexing
service provided by this syscon, for which there is work in progress at
[1].
Link: https://lore.kernel.org/linux-gpio/20240723-uncouple-enforcer-7c48e4a4fefe@wendy/ [1]
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
The Top Level Mode Multiplexer (TLMM) in the Kaanapali SoC provide GPIO and
pinctrl functionality for UFS, SDC and 217 GPIO pins.
Add a DeviceTree binding to describe the Kaanapali TLMM block.
Signed-off-by: Jingyi Wang <jingyi.wang@oss.qualcomm.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Bjorn Andersson <andersson@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Convert the marvell,armada3710-(sb|nb)-pinctrl binding to DT schema
format. The binding includes the "marvell,armada-3700-xtal-clock"
subnode which is simple enough to include here.
Mark interrupt-controller/#interrupt-cells as required as the users have
them and the h/w is either capable of interrupts or not.
As this syscon has 2 register ranges, syscon-common.yaml needs to be
updated to drop the restriction of 1 register entry.
Signed-off-by: Rob Herring (Arm) <robh@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Convert the Marvell/Synaptics Berlin pinctrl binding to DT schema
format. The "reg" property was not documented for the newer SoCs.
Otherwise, it's a straight-forward conversion.
Signed-off-by: Rob Herring (Arm) <robh@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Add the "ti,am62l-padconf" compatible to allow for some changes in the
driver in the future when needed.
Signed-off-by: Bryan Brattlof <bb@ti.com>
Acked-by: Rob Herring (Arm) <robh@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Pull more x86 updates from Borislav Petkov:
- Remove a bunch of asm implementing condition flags testing in KVM's
emulator in favor of int3_emulate_jcc() which is written in C
- Replace KVM fastops with C-based stubs which avoids problems with the
fastop infra related to latter not adhering to the C ABI due to their
special calling convention and, more importantly, bypassing compiler
control-flow integrity checking because they're written in asm
- Remove wrongly used static branches and other ugliness accumulated
over time in hyperv's hypercall implementation with a proper static
function call to the correct hypervisor call variant
- Add some fixes and modifications to allow running FRED-enabled
kernels in KVM even on non-FRED hardware
- Add kCFI improvements like validating indirect calls and prepare for
enabling kCFI with GCC. Add cmdline params documentation and other
code cleanups
- Use the single-byte 0xd6 insn as the official #UD single-byte
undefined opcode instruction as agreed upon by both x86 vendors
- Other smaller cleanups and touchups all over the place
* tag 'x86_core_for_v6.18_rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (24 commits)
x86,retpoline: Optimize patch_retpoline()
x86,ibt: Use UDB instead of 0xEA
x86/cfi: Remove __noinitretpoline and __noretpoline
x86/cfi: Add "debug" option to "cfi=" bootparam
x86/cfi: Standardize on common "CFI:" prefix for CFI reports
x86/cfi: Document the "cfi=" bootparam options
x86/traps: Clarify KCFI instruction layout
compiler_types.h: Move __nocfi out of compiler-specific header
objtool: Validate kCFI calls
x86/fred: KVM: VMX: Always use FRED for IRQs when CONFIG_X86_FRED=y
x86/fred: Play nice with invoking asm_fred_entry_from_kvm() on non-FRED hardware
x86/fred: Install system vector handlers even if FRED isn't fully enabled
x86/hyperv: Use direct call to hypercall-page
x86/hyperv: Clean up hv_do_hypercall()
KVM: x86: Remove fastops
KVM: x86: Convert em_salc() to C
KVM: x86: Introduce EM_ASM_3WCL
KVM: x86: Introduce EM_ASM_1SRC2
KVM: x86: Introduce EM_ASM_2CL
KVM: x86: Introduce EM_ASM_2W
...
Pull devicetree fixes from Rob Herring:
- Allow child nodes on renesas-bsc bus binding
- Drop node name pattern on allwinner,sun50i-a64-de2 bus binding
- Switch DT patchwork to kernel.org from ozlabs.org
- Fix some typos in docs and bindings
- Fix reference count in PCI node unittest
* tag 'devicetree-fixes-for-6.18-1' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux:
dt-bindings: bus: renesas-bsc: allow additional properties
dt-bindings: bus: allwinner,sun50i-a64-de2: don't check node names
MAINTAINERS: Move DT patchwork to kernel.org
of: unittest: Fix device reference count leak in of_unittest_pci_node_verify
of: doc: Fix typo in doc comments.
dt-bindings: mmc: Correct typo "upto" to "up to"
Allow additional properties to enable devices attached to the bus.
Fixes warnings like these:
arch/arm/boot/dts/renesas/sh73a0-kzm9g.dtb: bus@fec10000 (renesas,bsc-sh73a0): Unevaluated properties are not allowed ('ethernet@10000000' was unexpected)
arch/arm/boot/dts/renesas/r8a73a4-ape6evm.dtb: bus@fec10000 (renesas,bsc-r8a73a4): Unevaluated properties are not allowed ('ethernet@8000000', 'flash@0' were unexpected)
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Rob Herring (Arm) <robh@kernel.org>
Node names are already and properly checked by the core schema. No need
to do it again.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
[robh: Also drop [A-F] in unit address]
Signed-off-by: Rob Herring (Arm) <robh@kernel.org>
Pull sound fixes from Takashi Iwai:
"A few more small fixes for 6.18-rc1.
Most of changes are about ASoC Intel and SOF drivers, while a few
other device-specific fixes are found for HD-audio, USB-audio, ASoC
RT722VB and Meson"
* tag 'sound-fix-6.18-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound:
ASoC: rt722: add settings for rt722VB
ASoC: meson: aiu-encoder-i2s: fix bit clock polarity
ALSA: usb: fpc: replace kmalloc_array followed by copy_from_user with memdup_array_user
ALSA: hda/tas2781: Enable init_profile_id for device initialization
ALSA: emu10k1: Fix typo in docs
ALSA: hda/realtek: Add quirk for ASUS ROG Zephyrus Duo
ASoC: SOF: Intel: Read the LLP via the associated Link DMA channel
ASoC: SOF: ipc4-pcm: do not report invalid delay values
ASoC: SOF: sof-audio: add dev_dbg_ratelimited wrapper
ASoC: SOF: Intel: hda-pcm: Place the constraint on period time instead of buffer time
ASoC: SOF: ipc4-topology: Account for different ChainDMA host buffer size
ASoC: SOF: ipc4-topology: Correct the minimum host DMA buffer size
ASoC: SOF: ipc4-pcm: fix start offset calculation for chain DMA
ASoC: SOF: ipc4-pcm: fix delay calculation when DSP resamples
ASoC: SOF: ipc3-topology: Fix multi-core and static pipelines tear down
ALSA: hda/hdmi: Add pin fix for HP ProDesk model
Pull fbdev updates from Helge Deller:
"Beside the usual bunch of smaller bug fixes, the majority of changes
were by Zsolt Kajtar to improve the s3fb driver.
Bug fixes:
- Bounds checking to fix vmalloc-out-of-bounds (Albin Babu Varghese)
- Fix logic error in "offb" name match (Finn Thain)
- simplefb: Fix use after free in (Janne Grunau)
- s3fb: Various fixes and powersave improvements (Zsolt Kajtar)
Enhancements & code cleanups:
- Various fixes in the documentation (Bagas Sanjaya)
- Use string choices helpers (Chelsy Ratnawat)
- xenfb: Use vmalloc_array to simplify code (Qianfeng Rong)
- mb862xxfb: use signed type for error codes (Qianfeng Rong)
- Make drivers depend on LCD_CLASS_DEVICE (Thomas Zimmermann)
- radeonfb: Remove stale product link in Kconfig (Sukrut Heroorkar)"
* tag 'fbdev-for-6.18-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/deller/linux-fbdev:
fbdev: Fix logic error in "offb" name match
fbdev: Add bounds checking in bit_putcs to fix vmalloc-out-of-bounds
fbdev: Make drivers depend on LCD_CLASS_DEVICE
fbdev: radeonfb: Remove stale product link in Kconfig
Documentation: fb: Retitle driver docs
Documentation: fb: ep93xx: Demote section headings
Documentation: fb: Split toctree
fbdev: simplefb: Fix use after free in simplefb_detach_genpds()
fbdev: s3fb: Revert mclk stop in suspend
fbdev: mb862xxfb: Use int type to store negative error codes
fbdev: Use string choices helpers
fbdev: core: Fix ubsan warning in pixel_to_pat
fbdev: s3fb: Implement 1 and 2 BPP modes, improve 4 BPP
fbdev: s3fb: Implement powersave for S3 FB
fbdev: xenfb: Use vmalloc_array to simplify code
Pull more i2c updates from Wolfram Sang:
- Second part of rtl9300 updates since dependencies are in now:
- general cleanups
- implement block read/write support
- add RTL9310 support
- DT schema conversion of hix5hd2 binding
- namespace cleanup for i2c-algo-pca
- minor simplification for mt65xx
* tag 'i2c-for-6.18-rc1-part2' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux:
dt-bindings: i2c: hisilicon,hix5hd2: convert to DT schema
i2c: mt65xx: convert set_speed function to void
i2c: rename wait_for_completion callback to wait_for_completion_cb
i2c: rtl9300: add support for RTL9310 I2C controller
dt-bindings: i2c: realtek,rtl9301-i2c: extend for RTL9310 support
i2c: rtl9300: use scoped guard instead of explicit lock/unlock
i2c: rtl9300: separate xfer configuration and execution
i2c: rtl9300: do not set read mode on every transfer
i2c: rtl9300: move setting SCL frequency to config_io
i2c: rtl9300: rename internal sda_pin to sda_num
dt-bindings: i2c: realtek,rtl9301-i2c: fix wording and typos
i2c: rtl9300: use regmap fields and API for registers
i2c: rtl9300: Implement I2C block read and write
Pull more VFIO updates from Alex Williamson:
- Optimizations for DMA map and unmap opertions through the type1 vfio
IOMMU backend.
This uses various means of batching and hints from the mm structures
to improve efficiency and therefore performance, resulting in a
significant speedup for huge page use cases (Li Zhe)
- Expose supported device migration features through debugfs (Cédric Le
Goater)
* tag 'vfio-v6.18-rc1-pt2' of https://github.com/awilliam/linux-vfio:
vfio: Dump migration features under debugfs
vfio/type1: optimize vfio_unpin_pages_remote()
vfio/type1: introduce a new member has_rsvd for struct vfio_dma
vfio/type1: batch vfio_find_vpfn() in function vfio_unpin_pages_remote()
vfio/type1: optimize vfio_pin_pages_remote()
mm: introduce num_pages_contiguous()
Pull input updates from Dmitry Torokhov:
- Conversions to yaml/json schema and fixes for input-related device
tree bindings
- New drivers:
- Awinic AW86927 haptic chip
- Hynitron CST816x series controller
- Himax HX852x(ES) touchscreen controller
- Fix uinput to not leak kernel memory via a gap in
uinput_ff_upload_compat structure
- Prevent overflow in pressure calculation in tsc2007 driver causing
phantom touches
- Make the Atmel maxTouch driver support generic touchscreen
configuration (flip, rotate, etc)
- Drop support for platform data in tca8418_keypad, pxa27x-keypad,
spear-keyboard and twl4030_keypad drivers, they all now rely on
generic device properties for configuration
- Other assorted changes and fixes
* tag 'input-for-v6.18-rc0' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input: (50 commits)
Input: atmel_mxt_ts - allow reset GPIO to sleep
Input: aw86927 - fix error code in probe()
Input: psxpad-spi - add a check for the return value of spi_setup()
Input: uinput - zero-initialize uinput_ff_upload_compat to avoid info leak
Input: aw86927 - add driver for Awinic AW86927
dt-bindings: input: Add Awinic AW86927
dt-bindings: touchscreen: remove touchscreen.txt
dt-bindings: arm: bcm: raspberrypi,bcm2835-firmware: Add touchscreen child node
dt-bindings: touchscreen: convert eeti bindings to json schema
Input: pm8941-pwrkey - disable wakeup for resin by default
dt-bindings: input: pm8941-pwrkey: Document wakeup-source property
Input: add driver for Hynitron CST816x series
dt-bindings: input: touchscreen: add hynitron cst816x series
Input: imx6ul_tsc - set glitch threshold by DTS property
dt-bindings: touchscreen: fsl,imx6ul-tsc: support glitch thresold
dt-bindings: touchscreen: add debounce-delay-us property
Input: ps2-gpio - fix typo
Input: atmel_mxt_ts - add support for generic touchscreen configurations
dt-bindings: input: maxtouch: add common touchscreen properties
dt-bindings: touchscreen: convert zet6223 bindings to json schema
...
Pull more power management updates from Rafael Wysocki:
"These are cpufreq fixes and cleanups on top of the material merged
previously, a power management core code fix and updates of the
runtime PM framework including unit tests, documentation updates and
introduction of auto-cleanup macros for runtime PM "resume and get"
and "get without resuming" operations.
Specifics:
- Make cpufreq drivers setting the default CPU transition latency to
CPUFREQ_ETERNAL specify a proper default transition latency value
instead which addresses a regression introduced during the 6.6
cycle that broke CPUFREQ_ETERNAL handling (Rafael Wysocki)
- Make the cpufreq CPPC driver use a proper transition delay value
when CPUFREQ_ETERNAL is returned by cppc_get_transition_latency()
to indicate an error condition (Rafael Wysocki)
- Make cppc_get_transition_latency() return a negative error code to
indicate error conditions instead of using CPUFREQ_ETERNAL for this
purpose and drop CPUFREQ_ETERNAL that has no other users (Rafael
Wysocki, Gopi Krishna Menon)
- Fix device leak in the mediatek cpufreq driver (Johan Hovold)
- Set target frequency on all CPUs sharing a policy during frequency
updates in the tegra186 cpufreq driver and make it initialize all
cores to max frequencies (Aaron Kling)
- Rust cpufreq helper cleanup (Thorsten Blum)
- Make pm_runtime_put*() family of functions return 1 when the given
device is already suspended which is consistent with the
documentation (Brian Norris)
- Add basic kunit tests for runtime PM API contracts and update
return values in kerneldoc comments for the runtime PM API (Brian
Norris, Dan Carpenter)
- Add auto-cleanup macros for runtime PM "resume and get" and "get
without resume" operations, use one of them in the PCI core and
drop the existing "free" macro introduced for similar purpose, but
somewhat cumbersome to use (Rafael Wysocki)
- Make the core power management code avoid waiting on device links
marked as SYNC_STATE_ONLY which is consistent with the handling of
those device links elsewhere (Pin-yen Lin)"
* tag 'pm-6.18-rc1-2' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
docs/zh_CN: Fix malformed table
docs/zh_TW: Fix malformed table
PM: runtime: Fix error checking for kunit_device_register()
PM: runtime: Introduce one more usage counter guard
cpufreq: Drop unused symbol CPUFREQ_ETERNAL
ACPI: CPPC: Do not use CPUFREQ_ETERNAL as an error value
cpufreq: CPPC: Avoid using CPUFREQ_ETERNAL as transition delay
cpufreq: Make drivers using CPUFREQ_ETERNAL specify transition latency
PM: runtime: Drop DEFINE_FREE() for pm_runtime_put()
PCI/sysfs: Use runtime PM guard macro for auto-cleanup
PM: runtime: Add auto-cleanup macros for "resume and get" operations
cpufreq: tegra186: Initialize all cores to max frequencies
cpufreq: tegra186: Set target frequency for all cpus in policy
rust: cpufreq: streamline find_supply_names
cpufreq: mediatek: fix device leak on probe failure
PM: sleep: Do not wait on SYNC_STATE_ONLY device links
PM: runtime: Update kerneldoc return codes
PM: runtime: Make put{,_sync}() return 1 when already suspended
PM: runtime: Add basic kunit tests for API contracts
Pull clk updates from Stephen Boyd:
"There's a bunch of patches here across drivers/clk/ to migrate drivers
to use struct clk_ops::determine_rate() instead of the round_rate()
one so that we can remove the round_rate clk_op entirely. Brian has
taken up that task which nobody else has wanted to do for close to a
decade. Thanks Brian!
This is all prerequisite work to get to the real task of improving the
clk rate setting process. Once we have determine_rate() used
everywhere, we'll be able to do things like chain the rate request
structs in linked lists to order the rate setting operations or add
more parameters without having to change every clk driver in
existence. It's also nice to not have multiple ways to do something
which just causes confusion for clk driver authors. Overall I'm glad
this is getting done.
Beyond this change we also have a tweak to the clk_lookup() function
in the core framework to use hashing on the clk name instead of a clk
tree walk with string comparisons. We _still_ rely on the clk name to
be unique, because historically we've used globally unique strings to
describe the clk tree topology. This tree walk becomes increasingly
slow as more clks are added to the system. Searching from the roots
for a duplicate is simple but pretty dumb and it wastes boot time so
we're using a hash table as an improvement. Ideally we wouldn't rely
on the strings to be unique at all, relegating them to simply debug
information, but that is future work that will likely require some
sort of Kconfig knob indicating strings aren't used for topology
description.
Outside of the core framework changes we have the usual new SoC
support and fixes to clk drivers for things that were discovered once
the clks were used by consumer drivers. Nothing in particular is
jumping out at me in the "misc" pile, except maybe the Amlogic driver
that has gone through a refactoring. That series got a fix from
testing in -next though so it seems likely that things have been
getting good test coverage for a couple weeks already"
* tag 'clk-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux: (299 commits)
clk: microchip: core: remove duplicate roclk_determine_rate()
reset: aspeed: register AST2700 reset auxiliary bus device
dt-bindings: clock: ast2700: modify soc0/1 clock define
clk: tegra: do not overallocate memory for bpmp clocks
clk: ep93xx: Use int type to store negative error codes
clk: nxp: Fix pll0 rate check condition in LPC18xx CGU driver
clk: loongson2: Add clock definitions for Loongson-2K0300 SoC
clk: loongson2: Avoid hardcoding firmware name of the reference clock
clk: loongson2: Allow zero divisors for dividers
clk: loongson2: Support scale clocks with an alternative mode
clk: loongson2: Allow specifying clock flags for gate clock
dt-bindings: clock: loongson2: Add Loongson-2K0300 compatible
clk: clocking-wizard: Fix output clock register offset for Versal platforms
clk: xilinx: Optimize divisor search in clk_wzrd_get_divisors_ver()
clk: mmp: pxa1908: Instantiate power driver through auxiliary bus
clk: s2mps11: add support for S2MPG10 PMIC clock
dt-bindings: clock: samsung,s2mps11: add s2mpg10
dt-bindings: stm32: cosmetic fixes for STM32MP25 clock and reset bindings
clk: stm32: introduce clocks for STM32MP21 platform
dt-bindings: stm32: add STM32MP21 clocks and reset bindings
...
Pull arm64 fixes from Will Deacon:
- Preserve old 'tt_core' UAPI for Hisilicon L3C PMU driver
- Ensure linear alias of kprobes instruction page is not writable
- Fix kernel stack unwinding from BPF
- Fix build warnings from the Fujitsu uncore PMU documentation
- Fix hang with deferred 'struct page' initialisation and MTE
- Consolidate KPTI page-table re-writing code
* tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux:
arm64: mte: Do not flag the zero page as PG_mte_tagged
docs: perf: Fujitsu: Fix htmldocs build warnings and errors
arm64: mm: Move KPTI helpers to mmu.c
tracing: Fix the bug where bpf_get_stackid returns -EFAULT on the ARM64
arm64: kprobes: call set_memory_rox() for kprobe page
drivers/perf: hisi: Add tt_core_deprecated for compatibility
Merge cpufreq fixes and cleanups, mostly on top of those fixes, for
6.18-rc1:
- Make cpufreq drivers setting the default CPU transition latency to
CPUFREQ_ETERNAL specify a proper default transition latency value
instead which addresses a regression introduced during the 6.6 cycle
that broke CPUFREQ_ETERNAL handling (Rafael Wysocki)
- Make the cpufreq CPPC driver use a proper transition delay value
when CPUFREQ_ETERNAL is returned by cppc_get_transition_latency() to
indicate an error condition (Rafael Wysocki)
- Make cppc_get_transition_latency() return a negative error code to
indicate error conditions instead of using CPUFREQ_ETERNAL for this
purpose and drop CPUFREQ_ETERNAL that has no other users (Rafael
Wysocki, Gopi Krishna Menon)
- Fix device leak in the mediatek cpufreq driver (Johan Hovold)
- Set target frequency on all CPUs sharing a policy during frequency
updates in the tegra186 cpufreq driver and make it initialize all
cores to max frequencies (Aaron Kling)
- Rust cpufreq helper cleanup (Thorsten Blum)
* pm-cpufreq:
docs/zh_CN: Fix malformed table
docs/zh_TW: Fix malformed table
cpufreq: Drop unused symbol CPUFREQ_ETERNAL
ACPI: CPPC: Do not use CPUFREQ_ETERNAL as an error value
cpufreq: CPPC: Avoid using CPUFREQ_ETERNAL as transition delay
cpufreq: Make drivers using CPUFREQ_ETERNAL specify transition latency
cpufreq: tegra186: Initialize all cores to max frequencies
cpufreq: tegra186: Set target frequency for all cpus in policy
rust: cpufreq: streamline find_supply_names
cpufreq: mediatek: fix device leak on probe failure
The MediaTek MT8196 SoC includes an embedded MCU referred to as "GPUEB",
acting as glue logic to control power and frequency of the Mali GPU.
This MCU runs special-purpose firmware for this use, and the main
application processor communicates with it through a mailbox.
Add a binding that describes this mailbox.
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Acked-by: Conor Dooley <conor.dooley@microchip.com>
Reviewed-by: Rob Herring (Arm) <robh@kernel.org>
Signed-off-by: Nicolas Frattaroli <nicolas.frattaroli@collabora.com>
Signed-off-by: Jassi Brar <jassisinghbrar@gmail.com>
The GCE Mailbox needs only one clock and the clock-names can be
used only by the driver (which, for instance, does not use it),
and this is true for all of the currently supported MediaTek SoCs.
Stop requiring to specify clock-names on all non-MT8195 GCEs.
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Reviewed-by: Chen-Yu Tsai <wenst@chromium.org>
Acked-by: Rob Herring (Arm) <robh@kernel.org>
Reviewed-by: Matthias Brugger <matthias.bgg@gmail.com>
Signed-off-by: Jassi Brar <jassisinghbrar@gmail.com>
Document CPU Control Processor (CPUCP) mailbox controller for Qualcomm
Glymur SoCs. It is software compatible with X1E80100 CPUCP mailbox
controller hence fallback to it.
Signed-off-by: Sibi Sankar <sibi.sankar@oss.qualcomm.com>
Acked-by: Rob Herring (Arm) <robh@kernel.org>
Signed-off-by: Jassi Brar <jassisinghbrar@gmail.com>
