Fix the following DT schema check warning:
./Documentation/devicetree/bindings/pinctrl/cix,sky1-pinctrl.yaml:68:1: [warning] too many blank lines (2 > 1) (empty-lines)
One newline is enough. No functional change.
Signed-off-by: Marek Vasut <marex@nabladev.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Clang warns (or errors with CONFIG_WERROR=y / W=e):
pinctrl/mediatek/pinctrl-airoha.c:2064:41: error: variable 'an7583_pinctrl_drive_e2_conf' is not needed and will not be emitted [-Werror,-Wunneeded-internal-declaration]
2064 | static const struct airoha_pinctrl_conf an7583_pinctrl_drive_e2_conf[] = {
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~
Due to a typo, an7583_pinctrl_drive_e2_conf is only used within
ARRAY_SIZE() (hence no instance of -Wunused-variable), which is
evaluated at compile time, so it will not be needed in the final object
file.
Fix the .confs assignment for AIROHA_PINCTRL_CONFS_DRIVE_E2 in
an7583_pinctrl_match_data to clear up the warning.
Closes: https://github.com/ClangBuiltLinux/linux/issues/2142
Fixes: 3ffeb17a9a ("pinctrl: airoha: add support for Airoha AN7583 PINs")
Signed-off-by: Nathan Chancellor <nathan@kernel.org>
Acked-by: Christian Marangi <ansuelsmth@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The blamed commit made the following changes:
-#define PINCTRL_FUNC_DESC(id)...
- .desc = PINCTRL_PINFUNCTION(#id, ...
+#define PINCTRL_FUNC_DESC(id, table)...
+ .desc = PINCTRL_PINFUNCTION(#id, ...
- PINCTRL_FUNC_DESC(pon)...
+ PINCTRL_FUNC_DESC("pon", pon)...
It's clear that the id of funcs doesn't match the definition.
Remove redundant #string from the definition to fix this issue:
pinctrl-airoha ...: invalid function mdio in map table
Fixes: 4043b0c45f ("pinctrl: airoha: generalize pins/group/function/confs handling")
Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
Acked-by: Christian Marangi <ansuelsmth@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Replace comma between expressions with semicolons.
Using a ',' in place of a ';' can have unintended side effects.
Although that is not the case here, it is seems best to use ';'
unless ',' is intended.
Found by inspection.
No functional change intended.
Compile tested only.
Signed-off-by: Chen Ni <nichen@iscas.ac.cn>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Add all the required entry to add suppot for Airoha AN7583 PINs.
Where possible the same function group are used from Airoha EN7581 to
reduce code duplication.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Document Airoha AN7583 Pin Controller based on Airoha EN7581 with some
minor difference on some function group (PCM and LED gpio).
To not bloat the EN7581 schema with massive if condition, use a
dedicated YAML schema for Airoha AN7583.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Reviewed-by: Conor Dooley <conor.dooley@microchip.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The PWM GPIO struct definition follow the same pattern for every GPIO
pin hence it can be converted to a macro.
Create 2 macro one for normal mux and one for ext mux and convert all
the entry to these new macro to reduce code size.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
PHY LED GPIO pinctrl struct definition is very similar across the
different 4 PHY and 2 LED and it can be generelized to a macro.
To reduce code size, convert them to a common macro.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
In preparation for support of Airoha AN7583, generalize
pins/group/function/confs handling and move them in match_data.
Inner function will base the values on the pinctrl priv struct instead of
relying on hardcoded struct.
This permits to use different PIN data while keeping the same logic.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
When a GPIO RIF configuration is in semaphore mode, and the semaphore
hasn't been taken before configuring the GPIO, the write operations
silently fail.
To avoid a silent fail when applying a pinctrl, if the pins that are
being configured are in semaphore mode, take the semaphore. Note that
there is no proper release of the RIF semaphore yet for pinctrl.
Signed-off-by: Gatien Chevallier <gatien.chevallier@foss.st.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Samsung pinctrl drivers changes for v6.19
Add pin controller support for Samsung Exynos8890 and Axis ARTPEC-9
SoCs. The latter is a newer design of Artpec SoCs made/designed by
Samsung, thus it shares most of the core blocks with Samsung Exynos,
including the pinctrl.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Convert the sprd,sc9860-pinctrl binding to DT schema format. What's
valid for the the sleep mode child nodes wasn't well defined. The schema
is based on the example (as there's no .dts with pin states) and the
driver's register definitions.
Signed-off-by: Rob Herring (Arm) <robh@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
pinctrl: renesas: Updates for v6.19
- Fix interrupt configuration and port mode after resume on RZ/G2L
family SoCs,
- Miscellaneous fixes and improvements.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This exports and calls the pinctrl_provide_dummies() function from
the CIX SKY1 driver.
The reasons are explained in a comment in the commit, in essence the
two pin controllers need to go through explicit state transitions
default->sleep->default despite they only handle one single state
each.
Reviewed-by: Hans Zhang <hans.zhang@cixtech.com>
Reviewed-by: Fugang Duan <fugang.duan@cixtech.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
With LLVM prior to 17.0.0:
drivers/pinctrl/pinctrl-mpfs-iomux0.c:89:2: error: initializer element is not a compile-time constant
MPFS_IOMUX0_GROUP(spi0),
^~~~~~~~~~~~~~~~~~~~~~~
drivers/pinctrl/pinctrl-mpfs-iomux0.c:79:10: note: expanded from macro 'MPFS_IOMUX0_GROUP'
.mask = BIT(mpfs_iomux0_##_name##_pins[0]), \
^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
include/vdso/bits.h:7:19: note: expanded from macro 'BIT'
\#define BIT(nr) (UL(1) << (nr))
^~~~~~~~~~~~~~~
This is a constant, but LLVM prior to a change from Nick to match the
gcc behaviour did not allow this. The macro isn't really all that much
of an idiot-proofing, just change it to the same sort that's in the
gpio2 driver, where a second argument provides the mask/setting.
Reported-by: Nathan Chancellor <nathan@kernel.org>
Link: https://github.com/ClangBuiltLinux/linux/issues/2140
Fixes: 46397274da ("pinctrl: add polarfire soc iomux0 pinmux driver")
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
Reviewed-by: Nathan Chancellor <nathan@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
In stm32_pctl_probe(), hwspin_lock_request_specific() is called to
request a hwspinlock, but the acquired lock is not freed on multiple
error paths after this call. This causes resource leakage when the
function fails to initialize properly.
Use devm_hwspin_lock_request_specific() instead of
hwspin_lock_request_specific() to automatically manage the hwspinlock
resource lifecycle.
Fixes: 97cfb6cd34 ("pinctrl: stm32: protect configuration registers with a hwspinlock")
Signed-off-by: Haotian Zhang <vulab@iscas.ac.cn>
Reviewed-by: Antonio Borneo <antonio.borneo@foss.st.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The probe function does not guarantee that chip registers are in their
default state. Thus using reg_defaults for regmap is incorrect.
For example, the chip may have already been configured by the bootloader
before the Linux driver loads, or the mcp might not have a reset at all
and not reset a state between reboots.
In such cases, using reg_defaults leads to the cache values diverging
from the actual registers values in the chip.
Previous attempts to fix consequences of this issue were made in
'commit 3ede3f8b4b ("pinctrl: mcp23s08: Reset all pins to input at
probe")', but this is insufficient. The OLAT register reset is also
required. And there's still potential for new issues arising due to cache
desynchronization of other registers.
Therefore, remove reg_defaults and provide num_reg_defaults_raw. In that
case the cache defaults being initialized from hardware.
Also switch cache type to REGCACHE_MAPLE, which is aware of (in)valid
cache entries.
And remove the force reset all pins to input at probe as it is no longer
required.
Link: https://lore.kernel.org/all/20251009132651.649099-2-bigunclemax@gmail.com/
Suggested-by: Mike Looijmans <mike.looijmans@topic.nl>
Suggested-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Suggested-by: Sander Vanheule <sander@svanheule.net>
Signed-off-by: Maksim Kiselev <bigunclemax@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Document the support of the I/O synchronization parameters:
- skew-delay-input-ps;
- skew-delay-output-ps;
- st,io-sync.
Forbid 'skew-delay-input-ps' and 'skew-delay-output-ps' to be both
present on the same pin.
Allow the new properties only with compatibles that support them.
Add an example that uses the new properties.
Co-developed-by: Fabien Dessenne <fabien.dessenne@foss.st.com>
Signed-off-by: Fabien Dessenne <fabien.dessenne@foss.st.com>
Signed-off-by: Antonio Borneo <antonio.borneo@foss.st.com>
Reviewed-by: Conor Dooley <conor.dooley@microchip.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Devices in the stm32mp2xx family include an I/O synchronization
block on each pin that is used to fine tune and improve the I/O
timing margins of high speed synchronous interfaces.
It can be configured to provide independently for each pin:
- skew rate on input direction or latch delay on output direction;
- inversion of clock signals or re-sampling of data signals.
Add support for the generic properties:
- skew-delay-input-ps;
- skew-delay-output-ps.
Add support for the property 'st,io-sync' to configure clock
inversion or data re-sampling mode.
Show the new parameters on debugfs pinconf-pins.
Enable it for the stm32mp257 pinctrl driver.
Co-developed-by: Valentin Caron <valentin.caron@foss.st.com>
Signed-off-by: Valentin Caron <valentin.caron@foss.st.com>
Co-developed-by: Fabien Dessenne <fabien.dessenne@foss.st.com>
Signed-off-by: Fabien Dessenne <fabien.dessenne@foss.st.com>
Signed-off-by: Antonio Borneo <antonio.borneo@foss.st.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Change type of variable to avoid keeping the bool return value in
a variable of u32 type.
Signed-off-by: Antonio Borneo <antonio.borneo@foss.st.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
There is no need to acquire a spinlock to only read a register for
debugfs reporting.
Drop such useless spinlock save and restore.
Signed-off-by: Antonio Borneo <antonio.borneo@foss.st.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Use C bit-field to keep the backup of the pin status, instead of
explicitly handling the bit-field through shift and mask of a u32
container.
Signed-off-by: Antonio Borneo <antonio.borneo@foss.st.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Reduce the number of parameters of the function by moving inside
the function the decoding of the field 'config'.
While there:
- change the type of 'param' to 'unsigned int' to handle the extra
values not in 'enum pin_config_param';
- change the type of 'arg' to 'u32' to avoid additional conversions
and align to 'u32' the corresponding param of __stm32_gpio_set().
Signed-off-by: Antonio Borneo <antonio.borneo@foss.st.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Add the properties 'skew-delay-input-ps' and 'skew-delay-output-ps'
to specify independent skew delay value for the two pin's directions.
Make the new properties unavailable when the existing property
'skew-delay' is selected.
Signed-off-by: Antonio Borneo <antonio.borneo@foss.st.com>
Acked-by: Conor Dooley <conor.dooley@microchip.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Add the properties 'skew-delay-input-ps' and 'skew-delay-output-ps'
to the generic parameters used for parsing DT files. This allows to
specify the independent skew delay value for the two directions.
This enables drivers that use the generic pin configuration to get
the value passed through these new properties.
Signed-off-by: Antonio Borneo <antonio.borneo@foss.st.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Allow a generic pinconf property to specify its argument as one of
the strings in a match list.
Convert the matching string to an integer value using the index in
the list, then keep using this value in the generic pinconf code.
Signed-off-by: Antonio Borneo <antonio.borneo@foss.st.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
There are two pin-controllers on Cix Sky1 platform.
one is used under S0 state, the other is used under S0 and S5 state.
Signed-off-by: Gary Yang <gary.yang@cixtech.com>
[Dropped pinctrl_provide_dummies()]
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The pin-controller is used to control the Soc pins.
There are two pin-controllers on Cix Sky1 platform.
One is used under S0 state, the other is used under
S0 and S5 state.
Signed-off-by: Gary Yang <gary.yang@cixtech.com>
Reviewed-by: Conor Dooley <conor.dooley@microchip.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Add the new gpio2 and iomux0 drivers and bindings to the existing entry
for Microchip RISC-V devices.
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
On Polarfire SoC, iomux0 is responsible for routing functions to either
Multiprocessor Subsystem (MSS) IOs or to the FPGA fabric, where they
can either interface with custom RTL or be routed to the FPGA fabric's
IOs. Add a driver for it.
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
On Polarfire SoC, iomux0 is responsible for routing functions to either
Multiprocessor Subsystem (MSS) IOs or to the FPGA fabric, where they
can either interface with custom RTL or be routed to the FPGA fabric's
IOs. Document it.
Reviewed-by: Rob Herring (Arm) <robh@kernel.org>
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The pic64gx has a second pinmux "downstream" of the iomux0 pinmux. The
documentation for the SoC provides no name for this device, but it is
used to swap pins between either GPIO controller #2 or select other
functions, hence the "gpio2" name. Add a driver for it.
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The pic64gx has a second pinmux "downstream" of the iomux0 pinmux. The
documentation for the SoC provides no name for this device, but it is
used to swap pins between either GPIO controller #2 or select other
functions, hence the "gpio2" name. Currently there is no documentation
about what each bit actually does that is publicly available, nor (I
believe) what pins are affected. That info is as follows:
pin role (1/0)
--- ----------
E14 MAC_0_MDC/GPIO_2_0
E15 MAC_0_MDIO/GPIO_2_1
F16 MAC_1_MDC/GPIO_2_2
F17 MAC_1_MDIO/GPIO_2_3
D19 SPI_0_CLK/GPIO_2_4
B18 SPI_0_SS0/GPIO_2_5
B10 CAN_0_RXBUS/GPIO_2_6
C14 PCIE_PERST_2#/GPIO_2_7
E18 PCIE_WAKE#/GPIO_2_8
D18 PCIE_PERST_1#/GPIO_2_9
E19 SPI_0_DO/GPIO_2_10
C7 SPI_0_DI/GPIO_2_11
D6 QSPI_SS0/GPIO_2_12
D7 QSPI_CLK (B)/GPIO_2_13
C9 QSPI_DATA0/GPIO_2_14
C10 QSPI_DATA1/GPIO_2_15
A5 QSPI_DATA2/GPIO_2_16
A6 QSPI_DATA3/GPIO_2_17
D8 MMUART_3_RXD/GPIO_2_18
D9 MMUART_3_TXD/GPIO_2_19
B8 MMUART_4_RXD/GPIO_2_20
A8 MMUART_4_TXD/GPIO_2_21
C12 CAN_1_TXBUS/GPIO_2_22
B12 CAN_1_RXBUS/GPIO_2_23
A11 CAN_0_TX_EBL_N/GPIO_2_24
A10 CAN_1_TX_EBL_N/GPIO_2_25
D11 MMUART_2_RXD/GPIO_2_26
C11 MMUART_2_TXD/GPIO_2_27
B9 CAN_0_TXBUS/GPIO_2_28
Reviewed-by: Rob Herring (Arm) <robh@kernel.org>
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
mpfs pinctrl binding base
The pinctrl binding patch for iomux0 mpfs adds a ref to itself to the
syscon/mfd mss-top-sysreg binding, and therefore needs that file to
exist.
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
