The 'ocr' parameter passed to mmc_set_signal_voltage()
defines the power-on voltage used when power cycling
after a failure to set the voltage. However, in the
case of mmc_sdio_init_card(), the value passed has the
R4_18V_PRESENT flag set which is not valid for power-on
and results in an invalid vdd. Fix by passing the card's
ocr value which does not have the flag.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Cc: stable@vger.kernel.org # v3.13+
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
In some cases, the stronger 33 Ohm driver strength must not be used
so it is not a suitable default. Change it to the standard default
50 Ohm value.
The patch applies to v4.2+ except the file name changed. It is
drivers/mmc/host/sdhci-pci.c prior to v.4.4.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Cc: stable@vger.kernel.org # v4.2+
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Commit cc4f414c88 ("mmc: mmc: Add driver strength selection")
added driver strength selection for eMMC HS200 and HS400 modes.
That patch also set the driver stength when transitioning through
High Speed mode to HS200/HS400, but driver strength is not defined
for High Speed mode. While the JEDEC specification is not clear
on this point it has been observed to cause problems for some eMMC,
and removing the driver strength setting in this case makes it
consistent with the normal use of High Speed mode.
Signed-off-by: Wenkai Du <wenkai.du@intel.com>
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Cc: stable@vger.kernel.org # v4.2+
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This patch introduce a new MMC_CAP2_NO_SDIO cap used to tell the mmc
core to not send SDIO specific commands.
Signed-off-by: Carlo Caione <carlo@endlessm.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
A previous patch had removed esdhc_of_platform_init() by mistake.
static void esdhc_of_platform_init(struct sdhci_host *host)
{
u32 vvn;
vvn = in_be32(host->ioaddr + SDHCI_SLOT_INT_STATUS);
vvn = (vvn & SDHCI_VENDOR_VER_MASK) >> SDHCI_VENDOR_VER_SHIFT;
if (vvn == VENDOR_V_22)
host->quirks2 |= SDHCI_QUIRK2_HOST_NO_CMD23;
if (vvn > VENDOR_V_22)
host->quirks &= ~SDHCI_QUIRK_NO_BUSY_IRQ;
}
This patch is used to fix it by add/remove some quirks according to
verdor version in probe.
Signed-off-by: Yangbo Lu <yangbo.lu@freescale.com>
Fixes: f4932cfd22 ("mmc: sdhci-of-esdhc: support both BE and LE host controller")
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The atmci_convert_chksize() function is no more valid for controller
version 0x600 due to the introduction of '2 data' chunk size.
Signed-off-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
atmel-mci-regs.h is only included in atmel-mci.c so move its content in
the driver and do some cleanup in these definitions to remove checkpatch
errors.
Signed-off-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The mmc pm notifiers were recently reworked, but the new
code produces a lot of warnings when CONFIG_PM_SLEEP is disabled:
In file included from ../drivers/mmc/core/sdio_bus.c:27:0:
drivers/mmc/core/core.h:97:13: warning: 'mmc_register_pm_notifier' defined but not used [-Wunused-function]
The obvious solution is to add the 'inline' keyword at the
function definition, as it should be for any function defined
in a header file.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Fixes: 0e40be7c20e0 ("mmc: core: Refactor code to register the MMC PM notifier")
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Here we use '|=' to set the tuning-step, but before that, we should
clear the tuning-step, otherwise we could got the wrong setting.
Signed-off-by: Haibo Chen <haibo.chen@freescale.com>
Acked-by: Dong Aisheng <aisheng.dong@freescale.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
When compiling the sh_mmcif driver for ARM64, we currently
get a harmless build warning:
../drivers/mmc/host/sh_mmcif.c: In function 'sh_mmcif_request_dma_one':
../drivers/mmc/host/sh_mmcif.c:417:4: warning: cast to pointer from integer of different size [-Wint-to-pointer-cast]
(void *)pdata->slave_id_tx :
^
../drivers/mmc/host/sh_mmcif.c:418:4: warning: cast to pointer from integer of different size [-Wint-to-pointer-cast]
(void *)pdata->slave_id_rx;
This could be worked around by adding another cast to uintptr_t, but
I decided to simplify the code a little more to avoid that. This
splits out the platform data using code into a separate function
and builds that only for CONFIG_SUPERH. This part still has a typecast
but does not need a second one. The SH platform code could be further
modified to pass a pointer directly as we do on other architectures
when we have a filter function.
The normal case is simplified further and now just calls
dma_request_slave_channel() directly without going through the
compat handling.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This is a trivial patch which fixes printed strings split across two
or more lines in the source. I tried to grep for some error output*,
but I couldn't find it easily because it was broken across multiple
lines. This patch makes my life easier.
* in particular "Timeout waiting for hardware interrupt."
Signed-off-by: Marek Vasut <marex@denx.de>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The mmc_pwrseq_ops structures are never modified, so declare them as const.
Done with the help of Coccinelle.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The data in the SoC description structures is static and can therefore
reside in read-only memory.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Fault-injection capability for MMC IO uses debugfs entries to configure
the attributes.
FAULT_INJECTION_DEBUG_FS must be enabled to use FAIL_MMC_REQUEST.
Replace FAULT_INJECTION with FAULT_INJECTION_DEBUG_FS.
Also remove 'select DEBUG_FS' since FAULT_INJECTION_DEBUG_FS depends on
it.
Signed-off-by: Adrien Schildknecht <adrien+dev@schischi.me>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Turn the informative message about no vmmc/vqmmc regulator found in
debug one. There is no need to indicate that something optional is
missing. Moreover, it can bring confusion, people who doesn't know
it is optional may consider these messages as warnings or errors.
Signed-off-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
_mmc_detect_card_removed() validates that the card is removable, but when
being called via the bus_ops ->detect() callbacks, the validation is
redundant as it's already done in mmc_rescan().
Move the validation of a removable card to the mmc_detect_card_removed()
API, which is where it's applicable, to allow the blk error recovery path
to get the response a bit earlier.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Instead of checking for "#ifdef" directly in the code, let's invent a pair
of mmc core functions to deal with register/unregister the MMC PM notifier
block. Implement stubs for these functions when CONFIG_PM_SLEEP is unset,
as in that case the PM notifiers isn't used.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
MMC_CAP_RUNTIME_RESUME was invented to decrease system PM resume time for
systems that particularly needs this. As the feature has matured let's
make it the default behavior for MMC/SD.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
As mmc_claim_host() invokes pm_runtime_get_sync() for the mmc host device,
it's important that the host is kept claimed for *all* accesses to it via
the host_ops callbacks.
In mmc_rescan(), the ->card_event() and the ->get_cd() callback are being
invoked without claiming the host, let's fix this.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The ->card_event() callback may be called when re-scan is disabled and for
non-removable cards, which both cases are unnecessary.
Instead let's move the call later in mmc_rescan() where these constraints
have been validated.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The driver will not probe without valid DMA channels so no need to check
if they are valid when the module is removed.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
CC: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Though the mmc core driver should/will continue to support the legacy
"enable-sdio-wakeup" property to enable SDIO as the wakeup source, we
need to add support for the new standard property "wakeup-source".
This patch adds support for "wakeup-source" property in addition to the
existing "enable-sdio-wakeup" property.
Cc: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Pull RTC fixes from Alexandre Belloni:
"Late fixes for the RTC subsystem for 4.4:
A fix for a nasty hardware bug in rk808 and an initialization
reordering in da9063 to fix a possible crash"
* tag 'rtc-4.4-3' of git://git.kernel.org/pub/scm/linux/kernel/git/abelloni/linux:
rtc: da9063: fix access ordering error during RTC interrupt at system power on
rtc: rk808: Compensate for Rockchip calendar deviation on November 31st
This fix alters the ordering of the IRQ and device registrations in the RTC
driver probe function. This change will apply to the RTC driver that supports
both DA9063 and DA9062 PMICs.
A problem could occur with the existing RTC driver if:
A system is started from a cold boot using the PMIC RTC IRQ to initiate a
power on operation. For instance, if an RTC alarm is used to start a
platform from power off.
The existing driver IRQ is requested before the device has been properly
registered.
i.e.
ret = devm_request_threaded_irq()
comes before
rtc->rtc_dev = devm_rtc_device_register();
In this case, the interrupt can be called before the device has been
registered and the handler can be called immediately. The IRQ handler
da9063_alarm_event() contains the function call
rtc_update_irq(rtc->rtc_dev, 1, RTC_IRQF | RTC_AF);
which in turn tries to access the unavailable rtc->rtc_dev.
The fix is to reorder the functions inside the RTC probe. The IRQ is
requested after the RTC device resource has been registered so that
get_irq_byname is the last thing to happen.
Signed-off-by: Steve Twiss <stwiss.opensource@diasemi.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
In A.D. 1582 Pope Gregory XIII found that the existing Julian calendar
insufficiently represented reality, and changed the rules about
calculating leap years to account for this. Similarly, in A.D. 2013
Rockchip hardware engineers found that the new Gregorian calendar still
contained flaws, and that the month of November should be counted up to
31 days instead. Unfortunately it takes a long time for calendar changes
to gain widespread adoption, and just like more than 300 years went by
before the last Protestant nation implemented Greg's proposal, we will
have to wait a while until all religions and operating system kernels
acknowledge the inherent advantages of the Rockchip system. Until then
we need to translate dates read from (and written to) Rockchip hardware
back to the Gregorian format.
This patch works by defining Jan 1st, 2016 as the arbitrary anchor date
on which Rockchip and Gregorian calendars are in sync. From that we can
translate arbitrary later dates back and forth by counting the number
of November/December transitons since the anchor date to determine the
offset between the calendars. We choose this method (rather than trying
to regularly "correct" the date stored in hardware) since it's the only
way to ensure perfect time-keeping even if the system may be shut down
for an unknown number of years. The drawback is that other software
reading the same hardware (e.g. mainboard firmware) must use the same
translation convention (including the same anchor date) to be able to
read and write correct timestamps from/to the RTC.
Signed-off-by: Julius Werner <jwerner@chromium.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Pull tty/serial fixes from Greg KH:
"Here are some tty/serial driver fixes for 4.4-rc6 that resolve some
reported problems. All of these have been in linux-next. The details
are in the shortlog"
* tag 'tty-4.4-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty:
tty: Fix GPF in flush_to_ldisc()
serial: earlycon: Add missing spinlock initialization
serial: sh-sci: Fix length of scatterlist
n_tty: Fix poll() after buffer-limited eof push read
serial: 8250_uniphier: fix dl_read and dl_write functions
Pull USB fixes from Greg KH:
"Here are some USB and PHY fixes for 4.4-rc6. All of them resolve some
reported problems. Full details in the shortlog"
* tag 'usb-4.4-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb:
USB: fix invalid memory access in hub_activate()
USB: ipaq.c: fix a timeout loop
phy: core: Get a refcount to phy in devm_of_phy_get_by_index()
phy: cygnus: pcie: add missing of_node_put
phy: miphy365x: add missing of_node_put
phy: miphy28lp: add missing of_node_put
phy: rockchip-usb: add missing of_node_put
phy: berlin-sata: add missing of_node_put
phy: mt65xx-usb3: add missing of_node_put
phy: brcmstb-sata: add missing of_node_put
phy: sun9i-usb: add USB dependency
Pull md fixes from Neil Brown:
"Four fixes for md:
- two recently introduced regressions fixed.
- one older bug in RAID10 - tagged for -stable since 4.2
- one minor sysfs api improvement"
* tag 'md/4.4-rc5-fixes' of git://neil.brown.name/md:
Fix remove_and_add_spares removes drive added as spare in slot_store
md: fix bug due to nested suspend
MD: change journal disk role to disk 0
md/raid10: fix data corruption and crash during resync
Pull powerpc fixes from Michael Ellerman:
- Partial revert of "powerpc: Individual System V IPC system calls"
- pr_warn_once on unsupported OPAL_MSG type from Stewart
- Fix deadlock in opal-irqchip introduced by "Fix double endian
conversion" from Alistair
* tag 'powerpc-4.4-5' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux:
powerpc/opal-irqchip: Fix deadlock introduced by "Fix double endian conversion"
powerpc/powernv: pr_warn_once on unsupported OPAL_MSG type
Partial revert of "powerpc: Individual System V IPC system calls"
Pull spi fixes from Mark Brown:
"A couple of reference counting bugs here, one in spidev and one with
holding an extra reference in the core that we never freed if we
removed a device, plus a driver specific fix. Both of the refcounting
bugs are very old but they've only been found by observation so
hopefully their impact has been low"
* tag 'spi-fix-v4.4-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi:
spi: fix parent-device reference leak
spi: spidev: Hold spi_lock over all defererences of spi in release()
spi-fsl-dspi: Fix CTAR Register access
Pull GPIO fixes from Linus Walleij:
"Some GPIO fixes for the v4.4 series. Most prominent: I revert the
error propagation from the .get() function until we can fix up all the
drivers properly for v4.5.
- Revert the error number propagation from the .get() vtable entry
temporarily, until we make the proper fixes to all drivers.
- Fix the clamping behaviour in the generic GPIO driver.
- Driver fix for the ath79 driver"
* tag 'gpio-v4.4-3' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio:
gpio: revert get() to non-errorprogating behaviour
gpio: generic: clamp values from bgpio_get_set()
gpio: ath79: Fix the logic to clear offset bit of AR71XX_GPIO_REG_OE register
Pull pin control fixes from Linus Walleij:
- Driver fixes for Freescale i.MX7D, Intel, Broadcom 2835
- One MAINTAINERS entry
* tag 'pinctrl-v4.4-3' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl:
MAINTAINERS: pinctrl: Add maintainers for pinctrl-single
pinctrl: bcm2835: Fix initial value for direction_output
pinctrl: intel: fix offset calculation issue of register PAD_OWN
pinctrl: intel: fix bug of register offset calculation
pinctrl: freescale: add ZERO_OFFSET_VALID flag for vf610 pinctrl
Pull i2c fixes from Wolfram Sang:
"A set of 'usual' driver bugfixes for the I2C subsystem"
* 'i2c/for-current' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux:
i2c: rcar: disable runtime PM correctly in slave mode
i2c: designware: Keep pm_runtime_enable/_disable calls in sync
i2c: designware: fix IO timeout issue for AMD controller
i2c: imx: init bus recovery info before adding i2c adapter
i2c: do not use 0x in front of %pa
i2c: davinci: Increase module clock frequency
i2c: mv64xxx: The n clockdiv factor is 0 based on sunxi SoCs
i2c: rk3x: populate correct variable for sda_falling_time
When we also are I2C slave, we need to disable runtime PM because the
address detection mechanism needs to be active all the time. However, we
can reenable runtime PM once the slave instance was unregistered. So,
use pm_runtime_get_sync/put to achieve this, since it has proper
refcounting. pm_runtime_allow/forbid is like a global knob controllable
from userspace which is unsuitable here.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Cc: stable@kernel.org
Pull power management fixes from Rafael Wysocki:
"These fix a potential regression introduced during the 4.3 cycle
(generic power domains framework), a nasty bug that has been present
forever (power capping RAPL driver), a build issue (Tegra cpufreq
driver) and a minor ugliness introduced recently (intel_pstate).
Specifics:
- Fix a potential regression in the generic power domains framework
introduced during the 4.3 development cycle that may lead to
spurious failures of system suspend in certain situations (Ulf
Hansson).
- Fix a problem in the power capping RAPL (Running Average Power
Limits) driver that causes it to initialize successfully on some
systems where it is not supposed to do that which is due to an
incorrect check in an initialization routine (Prarit Bhargava).
- Fix a build problem in the cpufreq Tegra driver that depends on the
regulator framework, but that dependency is not reflected in
Kconfig (Arnd Bergmann).
- Fix a recent mistake in the intel_pstate driver where a numeric
constant is used directly instead of a symbol defined specifically
for the case in question (Prarit Bhargava)"
* tag 'pm+acpi-4.4-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
powercap / RAPL: fix BIOS lock check
cpufreq: intel_pstate: Minor cleanup for FRAC_BITS
cpufreq: tegra: add regulator dependency for T124
PM / Domains: Allow runtime PM callbacks to be re-used during system PM
Pull SCSI fixes from James Bottomley:
"Three fixes this time, two in SES picked up by KASAN for various types
of buffer overrun. The first is a USB array which returns page 8
whatever is asked for and causes us to overrun with incorrect data
format assumptions and the second is an invalid iteration of page 10
(the additional information page).
The final fix is a reversion of a NULL deref fix which caused
suspend/resume not to be called in pairs leading to incorrect device
operation (Jens has queued a more proper fix for the problem in
block)"
* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
ses: fix additional element traversal bug
Revert "SCSI: Fix NULL pointer dereference in runtime PM"
ses: Fix problems with simple enclosures
When sending "SLEEP" command to the controller it ceases scanning
completely and is unable to wake the system up from sleep, so if it is
configured as a wakeup source we should simply configure interrupt for
wakeup and rely on idle logic within the controller to reduce power
consumption while it is not used.
Signed-off-by: James Chen <james.chen@emc.com.tw>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Pull media fixes from Mauro Carvalho Chehab.
* tag 'media/v4.4-3' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media:
[media] airspy: increase USB control message buffer size
[media] hackrf: move RF gain ctrl enable behind module parameter
[media] hackrf: fix possible null ptr on debug printing
[media] Revert "[media] ivtv: avoid going past input/audio array"
Pull btrfs fixes from Chris Mason:
"A couple of small fixes"
* 'for-linus-4.4' of git://git.kernel.org/pub/scm/linux/kernel/git/mason/linux-btrfs:
Btrfs: check prepare_uptodate_page() error code earlier
Btrfs: check for empty bitmap list in setup_cluster_bitmaps
btrfs: fix misleading warning when space cache failed to load
Btrfs: fix transaction handle leak in balance
Btrfs: fix unprotected list move from unused_bgs to deleted_bgs list
