For now this helper only waits for the maximum duration of a single
conversion.
In practice, a "temperature measurement" will take twice this
time because it will also carry another analog conversion but as here we
will only care about the temperature conversion which happens first, we
can still only wait for a single sample and get the right data.
This helper will soon be improved to properly handle the end of
conversion interrupt as well as a higher number of samples.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/r/20210921115408.66711-13-miquel.raynal@bootlin.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
When hardware buffers are enabled (the cnvst pin being the trigger), one
should not mess with the device state by requesting a single channel
read.
There is already a iio_buffer_enabled() check in *_read_single_value()
to merely prevent this situation but the check is inconsistent since
buffers can be enabled after the if clause anyway. Instead, use the core
mutex by calling iio_device_claim/release_direct_mode().
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/r/20210921115408.66711-11-miquel.raynal@bootlin.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
We don't expect the (hardware) cnvst trigger to be enabled at boot time,
this is a user choice made in sysfs and there is a dedicated callback to
enable/disable this trigger. Hence, we can just ensure it is disabled in
the probe at initialization time and then assume that whenever a
->read_raw() call happens, the trigger has been disabled and conversions
will start on register write.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/r/20210921115408.66711-9-miquel.raynal@bootlin.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Provide a list of ->available_scan_masks which match the device's
capabilities. Basically, these devices are able to scan from 0 to N, N
being the highest voltage channel requested by the user. The temperature
can be included or not, but cannot be retrieved alone.
The consequence is, instead of reading and pushing to the IIO buffers
all channels each time, the "minimum" number of channels will be scanned
and pushed based on the ->active_scan_mask.
For example, if the user wants channels 1, 4 and 5, all channels from
0 to 5 will be scanned and pushed to the IIO buffers. The core will then
filter out the unneeded samples based on the ->active_scan_mask that has
been selected and only channels 1, 4 and 5 will be available to the user
in the shared buffer.
Provide a comment in the code explaining this logic.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/r/20210921115408.66711-5-miquel.raynal@bootlin.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
This adds ways for the SoC to wake from accelerometer wake events.
In the suspend function we skip disabling the sensor if wakeup-source
and events are activated.
If buffered reads are enabled they will be deactivated before suspend.
As the onboard buffer is only holding up to 32 12-bit X/Y/Z data
triplets.
Signed-off-by: Sean Nyekjaer <sean@geanix.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Link: https://lore.kernel.org/r/20210920114221.1595543-2-sean@geanix.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The ADC controller has a trimming register for fine-tune the reference
voltage. The trimming value comes from the OTP register which will be
written during chip production. This patch will read this OTP value and
configure it to the ADC register when the ADC controller probes and using
dts property "aspeed,trim-data-valid" to determine whether to execute this
flow.
Signed-off-by: Billy Tsai <billy_tsai@aspeedtech.com>
Link: https://lore.kernel.org/r/20210922081520.30580-12-billy_tsai@aspeedtech.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
In ast2600, ADC integrate dividing circuit at last input channel for
battery sensing. This patch use the dts property "battery-sensing" to
enable this feature makes the last channel of each adc can tolerance
higher voltage than reference voltage. The offset interface of ch7 will
be separated when enabling the battery sensing mode.
Signed-off-by: Billy Tsai <billy_tsai@aspeedtech.com>
Link: https://lore.kernel.org/r/20210922081520.30580-11-billy_tsai@aspeedtech.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The ADC clock formula is
ast2400/2500:
ADC clock period = PCLK * 2 * (ADC0C[31:17] + 1) * (ADC0C[9:0] + 1)
ast2600:
ADC clock period = PCLK * 2 * (ADC0C[15:0] + 1)
They all have one fixed divided 2 and the legacy driver didn't handle it.
This patch register the fixed factory clock device as the parent of ADC
clock scaler to fix this issue.
Signed-off-by: Billy Tsai <billy_tsai@aspeedtech.com>
Link: https://lore.kernel.org/r/20210922081520.30580-8-billy_tsai@aspeedtech.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
This patch refactors the model data structure to distinguish the
function form different versions of aspeed ADC.
- Rename the vref_voltage to vref_fixed_mv and add vref_mv driver data
When driver probe will check vref_fixed_mv value and store it to vref_mv
which isn't const value.
- Add num_channels
Make num_channles of iio device can be changed by different model_data
- Add need_prescaler flag and scaler_bit_width
The need_prescaler flag is used to tell the driver the clock divider needs
another Prescaler and the scaler_bit_width to set the clock divider
bitfield width.
Signed-off-by: Billy Tsai <billy_tsai@aspeedtech.com>
Link: https://lore.kernel.org/r/20210922081520.30580-3-billy_tsai@aspeedtech.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
This change converts the probe of the AD5064 driver to use only
device-managed functions.
The regulator_bulk_disable() is passed on a devm_add_action_or_reset() hook
and the devm_iio_device_register() can be used to register the IIO device.
The driver has both I2C and SPI hooks inside, so all these can be removed.
Signed-off-by: Alexandru Ardelean <aardelean@deviqon.com>
Link: https://lore.kernel.org/r/20210913115237.301310-1-aardelean@deviqon.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
This change does a conversion of the driver to use device-managed init
functions. The 2 regulators and the clock inits are converted to use
devm_add_action_or_reset() callbacks for de-initializing them when the
driver unloads.
And finally the devm_iio_device_register() function can be use to register
the device.
The remove hook can finally be removed and the spi_set_drvdata() call can
also be removed as the private data is no longer used.
Signed-off-by: Alexandru Ardelean <aardelean@deviqon.com>
Link: https://lore.kernel.org/r/20210913115209.300665-1-aardelean@deviqon.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
