By design the MES will return an array result that is twice the number
of hung doorbells it can report.
i.e. if up k reported doorbells are supported, then the
second half of the array, also of length k, holds the HQD information
(type/queue/pipe) where queue 1 corresponds to index 0 and k,
queue 2 corresponds to index 1 and k + 1 etc ...
The driver will use the HDQ info to target queue/pipe reset for
hardware scheduled user compute queues.
Signed-off-by: Jonathan Kim <jonathan.kim@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Initialized doorbells should be set to invalid rather than 0 to prevent
driver from over counting hung doorbells since it checks against the
invalid value to begin with.
Signed-off-by: Jonathan Kim <jonathan.kim@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Clean up the amdgpu hmm range functions for clearer
definition of each.
a. Split amdgpu_ttm_tt_get_user_pages_done into two:
1. amdgpu_hmm_range_valid: To check if the user pages
are valid and update seq num
2. amdgpu_hmm_range_free: Clean up the hmm range
and pfn memory.
b. amdgpu_ttm_tt_get_user_pages_done and
amdgpu_ttm_tt_discard_user_pages are similar function so remove
discard and directly use amdgpu_hmm_range_free to clean up the
hmm range and pfn memory.
Suggested-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Sunil Khatri <sunil.khatri@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
update the amdgpu_ttm_tt_get_user_pages and all dependent function
along with it callers to use a user allocated hmm_range buffer instead
hmm layer allocates the buffer.
This is a need to get hmm_range pointers easily accessible
without accessing the bo and that is a requirement for the
userqueue to lock the userptrs effectively.
Signed-off-by: Sunil Khatri <sunil.khatri@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
GFX12 MES uses low 32 bits of status return for success (1 or 0)
and high bits for debug information if low bits are 0.
GFX11 MES doesn't do this so checking full 64-bit status return
for 1 or 0 is still valid.
Signed-off-by: Jonathan Kim <jonathan.kim@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
Previously, APU platforms (and other scenarios with uninitialized VRAM managers)
triggered a NULL pointer dereference in `ttm_resource_manager_usage()`. The root
cause is not that the `struct ttm_resource_manager *man` pointer itself is NULL,
but that `man->bdev` (the backing device pointer within the manager) remains
uninitialized (NULL) on APUs—since APUs lack dedicated VRAM and do not fully
set up VRAM manager structures. When `ttm_resource_manager_usage()` attempts to
acquire `man->bdev->lru_lock`, it dereferences the NULL `man->bdev`, leading to
a kernel OOPS.
1. **amdgpu_cs.c**: Extend the existing bandwidth control check in
`amdgpu_cs_get_threshold_for_moves()` to include a check for
`ttm_resource_manager_used()`. If the manager is not used (uninitialized
`bdev`), return 0 for migration thresholds immediately—skipping VRAM-specific
logic that would trigger the NULL dereference.
2. **amdgpu_kms.c**: Update the `AMDGPU_INFO_VRAM_USAGE` ioctl and memory info
reporting to use a conditional: if the manager is used, return the real VRAM
usage; otherwise, return 0. This avoids accessing `man->bdev` when it is
NULL.
3. **amdgpu_virt.c**: Modify the vf2pf (virtual function to physical function)
data write path. Use `ttm_resource_manager_used()` to check validity: if the
manager is usable, calculate `fb_usage` from VRAM usage; otherwise, set
`fb_usage` to 0 (APUs have no discrete framebuffer to report).
This approach is more robust than APU-specific checks because it:
- Works for all scenarios where the VRAM manager is uninitialized (not just APUs),
- Aligns with TTM's design by using its native helper function,
- Preserves correct behavior for discrete GPUs (which have fully initialized
`man->bdev` and pass the `ttm_resource_manager_used()` check).
v4: use ttm_resource_manager_used(&adev->mman.vram_mgr.manager) instead of checking the adev->gmc.is_app_apu flag (Christian)
Reviewed-by: Christian König <christian.koenig@amd.com>
Suggested-by: Lijo Lazar <lijo.lazar@amd.com>
Signed-off-by: Jesse Zhang <Jesse.Zhang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Remove extra multiplication.
CIK GPUs such as Hawaii appear to use PP_TABLE_V0 in which case
the shutdown temperature is hardcoded in smu7_init_dpm_defaults
and is already multiplied by 1000. The value was mistakenly
multiplied another time by smu7_get_thermal_temperature_range.
Fixes: 4ba082572a ("drm/amd/powerplay: export the thermal ranges of VI asics (V2)")
Closes: https://gitlab.freedesktop.org/drm/amd/-/issues/1676
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Timur Kristóf <timur.kristof@gmail.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
The atomic variable vm_fault_info_updated is used to synchronize access to
adev->gmc.vm_fault_info between the interrupt handler and
get_vm_fault_info().
The default atomic functions like atomic_set() and atomic_read() do not
provide memory barriers. This allows for CPU instruction reordering,
meaning the memory accesses to vm_fault_info and the vm_fault_info_updated
flag are not guaranteed to occur in the intended order. This creates a
race condition that can lead to inconsistent or stale data being used.
The previous implementation, which used an explicit mb(), was incomplete
and inefficient. It failed to account for all potential CPU reorderings,
such as the access of vm_fault_info being reordered before the atomic_read
of the flag. This approach is also more verbose and less performant than
using the proper atomic functions with acquire/release semantics.
Fix this by switching to atomic_set_release() and atomic_read_acquire().
These functions provide the necessary acquire and release semantics,
which act as memory barriers to ensure the correct order of operations.
It is also more efficient and idiomatic than using explicit full memory
barriers.
Fixes: b97dfa27ef ("drm/amdgpu: save vm fault information for amdkfd")
Cc: stable@vger.kernel.org
Signed-off-by: Gui-Dong Han <hanguidong02@gmail.com>
Signed-off-by: Felix Kuehling <felix.kuehling@amd.com>
Reviewed-by: Felix Kuehling <felix.kuehling@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
When we backup ring contents to reemit after a queue reset,
we don't backup ring contents from the bad context. When
we signal the fences, we should set an error on those
fences as well.
v2: misc cleanups
v3: add locking for fence error, fix comment (Christian)
v4: fix wrap around, locking (Christian)
Fixes: 77cc0da39c ("drm/amdgpu: track ring state associated with a fence")
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Chips which use the IP discovery firmware loaded by the driver
reported incorrect harvesting information in the ip discovery
table in sysfs because the driver only uses the ip discovery
firmware for populating sysfs and not for direct parsing for the
driver itself as such, the fields that are used to print the
harvesting info in sysfs report incorrect data for some IPs. Populate
the relevant fields for this case as well.
Fixes: 514678da56 ("drm/amdgpu/discovery: fix fw based ip discovery")
Acked-by: Tom St Denis <tom.stdenis@amd.com>
Reviewed-by: Lijo Lazar <lijo.lazar@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
The Constant Engine found on gfx6-gfx10 HW has been a notorious source of
problems.
RADV never used it in the first place, radeonsi only used it for a few
releases around 2017 for gfx6-gfx9 before dropping support for it as
well.
While investigating another problem I just recently found that submitting
to the CE seems to be completely broken on gfx9 for quite a while.
Since nobody complained about that problem it most likely means that
nobody is using any of the affected radeonsi versions on current Linux
kernels any more.
So to potentially phase out the support for the CE and eliminate another
source of problems block submitting CE IBs unless it is enabled again
using a debug flag.
Signed-off-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Acked-by: Timur Kristóf <timur.kristof@gmail.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Enabling ASPM causes randoms hangs on Tahiti and Oland on Zen4.
It's unclear if this is a platform-specific or GPU-specific issue.
Disable ASPM on SI for the time being.
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Timur Kristóf <timur.kristof@gmail.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
On various SI GPUs, a flickering can be observed near the bottom
edge of the screen when using a single 4K 60Hz monitor over DP.
Disabling MCLK switching works around this problem.
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Timur Kristóf <timur.kristof@gmail.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
intel_frontbuffer_get() is what locks out subsequent set_tiling
changes to the bo. Thus the fence vs. modifier check must be done
after intel_frontbuffer_get(), or else a concurrent set_tiling ioctl
might sneak in and change the fence after the check has been done.
Close the race again. See commit dd689287b9 ("drm/i915: Prevent
concurrent tiling/framebuffer modifications") for the previous
instance.
v2: Reorder intel_user_framebuffer_destroy() to match the unwind (Jani)
Cc: Jouni Högander <jouni.hogander@intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Fixes: 10690b8a49 ("drm/i915/display: Add intel_fb_bo_framebuffer_fini")
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20251003145734.7634-3-ville.syrjala@linux.intel.com
(cherry picked from commit 1d1e4ded21)
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Currently xe's intel_frontbuffer implementation forgets to
hold a reference on the bo. This makes the entire thing
extremely fragile as the cleanup order now depends on bo
references held by other things
(namely intel_fb_bo_framebuffer_fini()).
Move the bo refcounting to intel_frontbuffer_{get,release}()
so that both i915 and xe do this the same way.
I first tried to fix this by having xe do the refcounting
from its intel_bo_set_frontbuffer() implementation
(which is what i915 does currently), but turns out xe's
drm_gem_object_free() can sleep and thus drm_gem_object_put()
isn't safe to call while we hold fb_tracking.lock.
Fixes: 10690b8a49 ("drm/i915/display: Add intel_fb_bo_framebuffer_fini")
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20251003145734.7634-2-ville.syrjala@linux.intel.com
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
(cherry picked from commit eb4d490729)
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
In normal operation, a registered exec queue is disabled and
deregistered through the GuC, and freed only after the GuC confirms
completion. However, if the driver is forced to unbind while the exec
queue is still running, the user may call exec_destroy() after the GuC
has already been stopped and CT communication disabled.
In this case, the driver cannot receive a response from the GuC,
preventing proper cleanup of exec queue resources. Fix this by directly
releasing the resources when GuC is not running.
Here is the failure dmesg log:
"
[ 468.089581] ---[ end trace 0000000000000000 ]---
[ 468.089608] pci 0000:03:00.0: [drm] *ERROR* GT0: GUC ID manager unclean (1/65535)
[ 468.090558] pci 0000:03:00.0: [drm] GT0: total 65535
[ 468.090562] pci 0000:03:00.0: [drm] GT0: used 1
[ 468.090564] pci 0000:03:00.0: [drm] GT0: range 1..1 (1)
[ 468.092716] ------------[ cut here ]------------
[ 468.092719] WARNING: CPU: 14 PID: 4775 at drivers/gpu/drm/xe/xe_ttm_vram_mgr.c:298 ttm_vram_mgr_fini+0xf8/0x130 [xe]
"
v2: use xe_uc_fw_is_running() instead of xe_guc_ct_enabled().
As CT may go down and come back during VF migration.
Fixes: dd08ebf6c3 ("drm/xe: Introduce a new DRM driver for Intel GPUs")
Cc: stable@vger.kernel.org
Cc: Matthew Brost <matthew.brost@intel.com>
Signed-off-by: Shuicheng Lin <shuicheng.lin@intel.com>
Reviewed-by: Matthew Brost <matthew.brost@intel.com>
Signed-off-by: Matthew Brost <matthew.brost@intel.com>
Link: https://lore.kernel.org/r/20251010172529.2967639-2-shuicheng.lin@intel.com
The state pointer found in the struct drm_atomic_state internals for
most object is a bit ambiguous, and confusing when those internals also
have old state and new state.
After the recent cleanups, the state pointer only use is to point to the
state we need to free when destroying the atomic state.
We can thus rename it something less ambiguous, and hopefully more
meaningful.
Acked-by: Thomas Zimmermann <tzimmermann@suse.de>
Link: https://lore.kernel.org/r/20251008-drm-rename-state-v2-1-49b490b2676a@kernel.org
Signed-off-by: Maxime Ripard <mripard@kernel.org>
There is now a new LT9211 rev. U5, which reports chip ID 0x18 0x01 0xe4 .
The previous LT9211 reported chip ID 0x18 0x01 0xe3 , which is what the
driver checks for right now. Since there is a possibility there will be
yet another revision of the LT9211 in the future, drop the last version
nibble check to allow all future revisions of the chip to work with this
driver.
This fix makes LT9211 rev. U5 work with this driver.
Fixes: 8ce4129e3d ("drm/bridge: lt9211: Add Lontium LT9211 bridge driver")
Signed-off-by: Marek Vasut <marek.vasut@mailbox.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Link: https://lore.kernel.org/r/20251011110017.12521-1-marek.vasut@mailbox.org
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
