Add btwilink device for IGEPv2 Rev. F and IGEP COM MODULE Rev. G.
Signed-off-by: Enric Balletbo i Serra <eballetbo@iseebcn.com>
Acked-by: Javier Martinez Canillas <javier@dowhile0.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
We can't suppose that the i2c2 pins are configured as I2C bus, these pins are
connected to expansion connectors.
Signed-off-by: Enric Balletbo i Serra <eballetbo@iseebcn.com>
Acked-by: Javier Martinez Canillas <javier@dowhile0.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add support for the new hardware revision of the IGEPv2. Basically, the new
revision F replaces the old Wifi module for a Wilink8 based module.
Signed-off-by: Enric Balletbo i Serra <eballetbo@iseebcn.com>
Acked-by: Javier Martinez Canillas <javier@dowhile0.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Use the omap3-igep0020-common.dtsi file and remove repeated parts leaving
the nodes that are not common between IGEPv2 hardware revisions.
Signed-off-by: Enric Balletbo i Serra <eballetbo@iseebcn.com>
Acked-by: Javier Martinez Canillas <javier@dowhile0.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add support for the new hardware revision of the IGEP COM MODULE. Basically,
the new revision G replaces the old Wifi module for a Wilink8 based module.
Signed-off-by: Enric Balletbo i Serra <eballetbo@iseebcn.com>
Acked-by: Javier Martinez Canillas <javier@dowhile0.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Use the omap3-igep0030-common.dtsi file and remove repeated parts leaving
the nodes that are not common between IGEP COM MODULE hardware revisions.
Signed-off-by: Enric Balletbo i Serra <eballetbo@iseebcn.com>
Acked-by: Javier Martinez Canillas <javier@dowhile0.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
New IGEP boards revisions will use another Wifi module, so this patch moves
the DT nodes outside the common omap3-igep.dtsi file to specific DT for every
board.
Signed-off-by: Enric Balletbo i Serra <eballetbo@iseebcn.com>
Acked-by: Javier Martinez Canillas <javier@dowhile0.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
We'll introduce new hardware revisions soon. This patch is only to
indicate which board revision supports this device tree file in order
to avoid confusions.
Signed-off-by: Enric Balletbo i Serra <eballetbo@iseebcn.com>
Acked-by: Javier Martinez Canillas <javier@dowhile0.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
We'll introduce new hardware revisions soon. This patch is only to
indicate which board revision supports this device tree file in order
to avoid confusions.
Signed-off-by: Enric Balletbo i Serra <eballetbo@iseebcn.com>
Acked-by: Javier Martinez Canillas <javier@dowhile0.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
At this moment all supported boards use same NAND chip, so has more sense
move the GPMC and NAND configuration to the omap3-igep.dtsi common place.
Signed-off-by: Enric Balletbo i Serra <eballetbo@iseebcn.com>
Acked-by: Javier Martinez Canillas <javier@dowhile0.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
UART2 is used to connect the processor with the bluetooth chip, these pins
are not common between IGEPv2 boards and IGEP COM MODULE boards. This patch
muxes the correct pins for every board and removes UART2 configuration from
common omap3-igep.dtsi file.
Signed-off-by: Enric Balletbo i Serra <eballetbo@iseebcn.com>
Acked-by: Javier Martinez Canillas <javier@dowhile0.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
by adding labels to DWC3 nodes, it's far easier
for boards to reference them.
Signed-off-by: Felipe Balbi <balbi@ti.com>
[tony@atomide.com: updated for otg 4 move to dra74x.dtsi]
Signed-off-by: Tony Lindgren <tony@atomide.com>
Adding CPSW phy-id, CPSW and MDIO pinmux configuration for active and
sleep states and enable them in board evm dts file.
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
DRA7 Data Manual (SPRS857L - August 2014) section 4.1.1 states: "All
unused power supply balls must be supplied with the voltages specified
in the Section 5.2, Recommended Operating Conditions".
This implies that all unused voltage rails for Vayu can never be
switched off even if the hardware blocks inside that voltage domain is
unused. Switching off these unused rails may result in stability issues
on other domains and increased leakage and power-on-hour impacts.
J6eco-evm dts file already considers this, however j6evm-dts file needs
to be fixed to consider this constraint of the SoC.
Signed-off-by: Nishanth Menon <nm@ti.com>
Acked-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add MMC1 and 2 nodes. MMC1 is SDcard and MMC2 is eMMC.
NOTE on MMC1 card detect: Ideally, we should be using in-built SDCD
support, but we dont have it yet. So, use the fact that control module
of DRA7 is setup such that no matter what mode one configures it, GPIO
option is always hardwired in - use GPIO mode for SDcard detection.
[peter.ujfalusi@ti.com]
The power line feeding the SD card is also used by other devices on the EVM.
Use generic name instead of mmc2_3v3 so when other devices want to use the
same regulator it will look a bit better.
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
With Commit adff5962fd ("Input: introduce palmas-pwrbutton"), we can
now support tps power button as a event source - This is SW7 (PB/WAKE)
on the J6-evm.
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Even thought sys_nirq1 is hardwired on the SoC for the pin, it is
better to configure the pin to the required mux configuration.
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The ldo4_reg regulator provides power to the USB1 and USB2
High Speed PHYs.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The 4th USB controller instance present only on the DRA74x family of
devices so move it there.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Acked-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
DRA72-evm has a 256MB 16-bit wide NAND chip. Add
pinmux and NAND node.
The NAND chips 'Chip select' and 'Write protect' can be
controlled using DIP Switch SW5. To use NAND,
the switch must be configured like so:
SW5.1 (NAND_SELn) = ON (LOW)
SW5.9 (GPMC_WPN) = OFF (HIGH)
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Tested-by: Nishanth Menon <nm@ti.com>
Acked-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Adding CPSW phy-id, CPSW and MDIO pinmux configuration for active and
sleep states and enable them in board evm dts file.
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add CPSW and MDIO related device tree data for DRA7XX and made as status
disabled. Phy-id, pinmux for active and sleep state needs to be added in
board dts files and enable the CPSW device.
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Use omap specific pinctrl defines (OMAP3_CORE1_IOPAD) to configure
the padconf register offset.
Signed-off-by: Marek Belisko <marek@goldelico.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add DSS related pinmux and display data nodes required to support
DVI video out on SBC-T3530, SBC-T3730 and SBC-T3517.
Signed-off-by: Dmitry Lifshitz <lifshitz@compulab.co.il>
Acked-by: Igor Grinberg <grinberg@compulab.co.il>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add the interrupts property to all the 13 mailbox nodes in
DRA7xx. The interrupts property information added is inline
with the expected values with the DRA7xx crossbar driver,
and is common to both DRA74x and DRA72x SoCs.
Do note that the mailbox 1 is only capable of generating out
3 interrupts, while all the remaining mailboxes have 4
interrupts each.
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Looks like we have some GPMC NAND timings missing device
width. This fixes "gpmc_cs_program_settings: invalid width 0!"
errors during boot.
Signed-off-by: Tony Lindgren <tony@atomide.com>
With the GPMC warnings now enabled, I noticed the LAN9220 timings
can overflow the GPMC registers with 200MHz L3 speed. Earlier we
were just skipping the bad timings and would continue with the
bootloader timings. Now we no longer allow to continue with bad
timings as we have the timings in the .dts files.
We could start using the GPMC clock divider, but let's instead
use the u-boot timings that are known to be working and a bit
faster. These are basically the u-boot NET_GPMC_CONFIG[1-6]
defines deciphered. Except that we don't set gpmc,burst-length
as that's only partially configured and does not seem to work
if fully enabled.
[tony@atomide.com: updated to remove gpmc,burst-length]
Signed-off-by: Tony Lindgren <tony@atomide.com>
The four port serial port on the zoom debug board uses a TL16CP754C
with a single interrupt and GPMC chip select. The serial ports each
use a 8 bytes for IO registers, and are 256 bytes apart on the GPMC
line.
Let's add timings for all four ports so we can remove the GPMC
workarounds for using bootloader timings.
Not caused by this patch, but looks like u-boot only properly
initializes the fifo on the first serial port. Currently the other
ports produce garbage at least with my version of u-boot. I suspect
that TL16CP754C needs non-standard initialization added to 8250
driver to properly fix this issue.
Cc: Roger Quadros <rogerq@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Let's use the bootloader values except for the partially configured
wait-pin that does not seem to work.
Cc: Roger Quadros <rogerq@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The GPMC binding is obviously very confusing as the values
are all over the place. People seem to confuse the GPMC partition
size for the chip select, and the device IO size within the GPMC
partition easily.
The ranges entry contains the GPMC partition size. And the
reg entry contains the size of the IO registers of the
device connected to the GPMC.
Let's fix the issue according to the following table:
Device GPMC partition size Device IO size
connected in the ranges entry in the reg entry
NAND 0x01000000 (16MB) 4
16550 0x01000000 (16MB) 8
smc91x 0x01000000 (16MB) 0xf
smc911x 0x01000000 (16MB) 0xff
OneNAND 0x01000000 (16MB) 0x20000 (128KB)
16MB NOR 0x01000000 (16MB) 0x01000000 (16MB)
32MB NOR 0x02000000 (32MB) 0x02000000 (32MB)
64MB NOR 0x04000000 (64MB) 0x04000000 (64MB)
128MB NOR 0x08000000 (128MB) 0x08000000 (128MB)
256MB NOR 0x10000000 (256MB) 0x10000000 (256MB)
Let's also add comments to the fixed entries while at it.
Acked-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Apparently some versions of nolo don't mux the all the necessary GPMC
pins for the smc91x probe to work properly. Let's fix this issue
by adding mux support for GPMC to the kernel.
Note that GPMC clk needs input enabled for OnenNAND to work.
Cc: Kevin Hilman <khilman@kernel.org>
Cc: Roger Quadros <rogerq@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Pull ARM SoC fixes from Olof Johansson:
"Another week, another small batch of fixes.
Most of these make zynq, socfpga and sunxi platforms work a bit
better:
- due to new requirements for regulators, DWMMC on socfpga broke past
v3.17
- SMP spinup fix for socfpga
- a few DT fixes for zynq
- another option (FIXED_REGULATOR) for sunxi is needed that used to
be selected by other options but no longer is.
- a couple of small DT fixes for at91
- ...and a couple for i.MX"
* tag 'armsoc-for-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
ARM: dts: imx28-evk: Let i2c0 run at 100kHz
ARM: i.MX6: Fix "emi" clock name typo
ARM: multi_v7_defconfig: enable CONFIG_MMC_DW_ROCKCHIP
ARM: sunxi_defconfig: enable CONFIG_REGULATOR_FIXED_VOLTAGE
ARM: dts: socfpga: Add a 3.3V fixed regulator node
ARM: dts: socfpga: Fix SD card detect
ARM: dts: socfpga: rename gpio nodes
ARM: at91/dt: sam9263: fix PLLB frequencies
power: reset: at91-reset: fix power down register
MAINTAINERS: add atmel ssc driver maintainer entry
arm: socfpga: fix fetching cpu1start_addr for SMP
ARM: zynq: DT: trivial: Fix mc node
ARM: zynq: DT: Add cadence watchdog node
ARM: zynq: DT: Add missing reference for memory-controller
ARM: zynq: DT: Add missing reference for ADC
ARM: zynq: DT: Add missing address for L2 pl310
ARM: zynq: DT: Remove 222 MHz OPP
ARM: zynq: DT: Fix GEM register area size
Merge "ARM: imx: fixes for 3.18" from Shawn Guo:
The i.MX fixes for 3.18:
- Revert one patch which increases I2C bus frequency on imx28-evk
- Fix a typo on imx6q EIM clock name
* tag 'imx-fixes-3.18' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux:
ARM: dts: imx28-evk: Let i2c0 run at 100kHz
ARM: i.MX6: Fix "emi" clock name typo
Signed-off-by: Olof Johansson <olof@lixom.net>
Commit 78b81f4666 ("ARM: dts: imx28-evk: Run I2C0 at 400kHz") caused issues
when doing the following sequence in loop:
- Boot the kernel
- Perform audio playback
- Reboot the system via 'reboot' command
In many times the audio card cannot be probed, which causes playback to fail.
After restoring to the original i2c0 frequency of 100kHz there is no such
problem anymore.
This reverts commit 78b81f4666.
Cc: <stable@vger.kernel.org> # 3.16+
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Fix a typo error, the "emi" names refer to the eim clocks.
The change fixes typo in EIM and EIM_SLOW pre-output dividers and
selectors clock names. Notably EIM_SLOW clock itself is named correctly.
Signed-off-by: Steve Longerbeam <steve_longerbeam@mentor.com>
[vladimir_zapolskiy@mentor.com: ported to v3.17]
Signed-off-by: Vladimir Zapolskiy <vladimir_zapolskiy@mentor.com>
Cc: Sascha Hauer <kernel@pengutronix.de>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
no sense having it a pointer - all instances have it pointing to
local variable in the same stack frame
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Pull MIPS fixes from Ralf Baechle:
"This is the first round of fixes and tying up loose ends for MIPS.
- plenty of fixes for build errors in specific obscure configurations
- remove redundant code on the Lantiq platform
- removal of a useless SEAD I2C driver that was causing a build issue
- fix an earlier TLB exeption handler fix to also work on Octeon.
- fix ISA level dependencies in FPU emulator's instruction decoding.
- don't hardcode kernel command line in Octeon software emulator.
- fix an earlier fix for the Loondson 2 clock setting"
* 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus:
MIPS: SEAD3: Fix I2C device registration.
MIPS: SEAD3: Nuke PIC32 I2C driver.
MIPS: ftrace: Fix a microMIPS build problem
MIPS: MSP71xx: Fix build error
MIPS: Malta: Do not build the malta-amon.c file if CMP is not enabled
MIPS: Prevent compiler warning from cop2_{save,restore}
MIPS: Kconfig: Add missing MIPS_CPS dependencies to PM and cpuidle
MIPS: idle: Remove leftover __pastwait symbol and its references
MIPS: Sibyte: Include the swarm subdir to the sb1250 LittleSur builds
MIPS: ptrace.h: Add a missing include
MIPS: ath79: Fix compilation error when CONFIG_PCI is disabled
MIPS: MSP71xx: Remove compilation error when CONFIG_MIPS_MT is present
MIPS: Octeon: Remove special case for simulator command line.
MIPS: tlbex: Properly fix HUGE TLB Refill exception handler
MIPS: loongson2_cpufreq: Fix CPU clock rate setting mismerge
pci: pci-lantiq: remove duplicate check on resource
MIPS: Lasat: Add missing CONFIG_PROC_FS dependency to PICVUE_PROC
MIPS: cp1emu: Fix ISA restrictions for cop1x_op instructions
Pull arm64 fixes from Catalin Marinas:
- enable 48-bit VA space now that KVM has been fixed, together with a
couple of fixes for pgd allocation alignment and initial memblock
current_limit. There is still a dependency on !ARM_SMMU which needs
to be updated as it uses the page table manipulation macros of the
host kernel
- eBPF fixes following changes/conflicts during the merging window
- Compat types affecting compat_elf_prpsinfo
- Compilation error on UP builds
- ASLR fix when /proc/sys/kernel/randomize_va_space == 0
- DT definitions for CLCD support on ARMv8 model platform
* tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux:
arm64: Fix memblock current_limit with 64K pages and 48-bit VA
arm64: ASLR: Don't randomise text when randomise_va_space == 0
arm64: vexpress: Add CLCD support to the ARMv8 model platform
arm64: Fix compilation error on UP builds
Documentation/arm64/memory.txt: fix typo
net: bpf: arm64: minor fix of type in jited
arm64: bpf: add 'load 64-bit immediate' instruction
arm64: bpf: add 'shift by register' instructions
net: bpf: arm64: address randomize and write protect JIT code
arm64: mm: Correct fixmap pagetable types
arm64: compat: fix compat types affecting struct compat_elf_prpsinfo
arm64: Align less than PAGE_SIZE pgds naturally
arm64: Allow 48-bits VA space without ARM_SMMU
Pull two sparc fixes from David Miller:
1) Fix boots with gcc-4.9 compiled sparc64 kernels.
2) Add missing __get_user_pages_fast() on sparc64 to fix hangs on
futexes used in transparent hugepage areas.
It's really idiotic to have a weak symbolled fallback that just
returns zero, and causes this kind of bug. There should be no
backup implementation and the link should fail if the architecture
fails to provide __get_user_pages_fast() and supports transparent
hugepages.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/sparc:
sparc64: Implement __get_user_pages_fast().
sparc64: Fix register corruption in top-most kernel stack frame during boot.
Pull kvm fixes from Paolo Bonzini:
"This is a pretty large update. I think it is roughly as big as what I
usually had for the _whole_ rc period.
There are a few bad bugs where the guest can OOPS or crash the host.
We have also started looking at attack models for nested
virtualization; bugs that usually result in the guest ring 0 crashing
itself become more worrisome if you have nested virtualization,
because the nested guest might bring down the non-nested guest as
well. For current uses of nested virtualization these do not really
have a security impact, but you never know and bugs are bugs
nevertheless.
A lot of these bugs are in 3.17 too, resulting in a large number of
stable@ Ccs. I checked that all the patches apply there with no
conflicts"
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm:
kvm: vfio: fix unregister kvm_device_ops of vfio
KVM: x86: Wrong assertion on paging_tmpl.h
kvm: fix excessive pages un-pinning in kvm_iommu_map error path.
KVM: x86: PREFETCH and HINT_NOP should have SrcMem flag
KVM: x86: Emulator does not decode clflush well
KVM: emulate: avoid accessing NULL ctxt->memopp
KVM: x86: Decoding guest instructions which cross page boundary may fail
kvm: x86: don't kill guest on unknown exit reason
kvm: vmx: handle invvpid vm exit gracefully
KVM: x86: Handle errors when RIP is set during far jumps
KVM: x86: Emulator fixes for eip canonical checks on near branches
KVM: x86: Fix wrong masking on relative jump/call
KVM: x86: Improve thread safety in pit
KVM: x86: Prevent host from panicking on shared MSR writes.
KVM: x86: Check non-canonical addresses upon WRMSR
Pull xen bug fixes from David Vrabel:
- Fix regression in xen_clocksource_read() which caused all Xen guests
to crash early in boot.
- Several fixes for super rare race conditions in the p2m.
- Assorted other minor fixes.
* tag 'stable/for-linus-3.18-b-rc1-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip:
xen/pci: Allocate memory for physdev_pci_device_add's optarr
x86/xen: panic on bad Xen-provided memory map
x86/xen: Fix incorrect per_cpu accessor in xen_clocksource_read()
x86/xen: avoid race in p2m handling
x86/xen: delay construction of mfn_list_list
x86/xen: avoid writing to freed memory after race in p2m handling
xen/balloon: Don't continue ballooning when BP_ECANCELED is encountered
