Pull futex fix from Ingo Molnar:
- Fix race in futex_pivot_pending() during private hash resize
that can cause stuck tasks (Yao Kai)
* tag 'locking-urgent-2026-08-08' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
futex: Fix race in futex_pivot_pending() during private hash resize
Pull USB / Thunderbolt fixes from Greg KH:
"Here are some small USB and Thunderbolt driver fixes for 7.2-rc7 that
resolve some reported issues. Included in here are:
- new quirk for some broken USB devices
- thunderbolt device fixes for reported issues
- usb gadget driver fix
- usb atm driver fix
- xhci driver fixes.
- other minor USB driver fixes
All of these have been in linux-next this week with no reported
issues"
* tag 'usb-7.2-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb:
usb: xhci: use BIT_ULL for CRCR bits to fix incorrect 64bit mask
usb: quirks: Add ShanWan gamepad to quirk list
usb: hub: Split announce_device() to log device identity before enumeration
usb: core: Add quirk for 255-bytes initial config read
usb: atm: cxacru: properly kill rcv_urb on error in cxacru_cm()
usb: misc: usbio: check ibuf_len against rxbuf_len in bulk msg
usb: gadget: f_ncm: Use unsigned int for ndp_index
usb: cdnsp: fix incorrect endian conversions for APB timeout register
thunderbolt: Initialize ->domain_released completion before it is being used
thunderbolt: icm: Preserve USB4 proxy data-valid bit
thunderbolt: Bound the DROM dual link port number before indexing sw->ports
thunderbolt: Fix bandwidth group reservation indexing
thunderbolt: stream: Unmap buffers with mapped size
Pull tty / serial / vt driver fixes from Greg KH:
"Here are some small serial and vt tty driver fixes for 7.2-rc7 that
resolve some reported problems. Included in here are:
- two vt core fixes
- amba-pl011 serial driver fixes
- 8250_of and 8250_dma driver fixes
- qcom-geni serial driver fix
- sc16is7xx serial driver fix
All of these have been in linux-next this week with no reported
issues"
* tag 'tty-7.2-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty:
serial: amba-pl011: synchronize DMA teardown
serial: amba-pl011: cancel RS485 hrtimers after freeing IRQ
serial: amba-pl011: fix indefinite RS485 post-send delay
vt: add permission check for KDSKBMETA ioctl
vt: stabilize tty reference in kbd_keycode with tty_port_tty_get
serial: 8250_of: clear stuck empty-FIFO RX-timeout on LPC32xx
serial: qcom-geni: fix TX DMA buffer flush
serial: 8250_dma: Clear stale RX state on shutdown
serial: sc16is7xx: enable THRI before filling TX FIFO
Pull staging driver fixes from Greg KH:
"Here are some more small staging driver fixes, just for the rtl8723bs
driver, for some reported problems found with it now that people are
starting to actually test the thing with "bad" networks.
Nothing major, but good to have in the -final release. All of these
have been in linux-next for over a week with no reported problems"
* tag 'staging-7.2-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging:
staging: rtl8723bs: validate monitor transmit frame lengths
staging: rtl8723bs: fix missing shared-key auth challenge length check
staging: rtl8723bs: fix OOB read in WMM_param_handler()
staging: rtl8723bs: fix OOB read in rtw_get_wpa_ie()
Pull char / misc and documentation fixes from Greg KH:
"Here are some small char/misc and nvmem and documentation fixes for
7.2-rc7 to resolve some reported issues. Included in here are:
- updates to the documentation for the kernel threat model and
security bugs to get the LLMs to actually follow what we have been
asking them to do (i.e. not claim security issues for things we do
not consider security issues.)
- nvmem driver fixes which required a tiny "layout" driver to be
added.
- fastrpc driver fixes
- mei driver fix
- counter driver fix
- binder driver fix
All of these have been in linux-next this week with no reported
problems"
* tag 'char-misc-7.2-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc:
docs: security-bugs: clarify some mandatory steps for AI reports
docs: coding-assistant: explain important steps when looking for bugs
docs: security-bugs: clarify what counts as a valid version
docs: threat-model: move fake devices out of "non production use"
docs: threat-model: clarify "security bug" vs "vulnerability"
counter: microchip-tcb-capture: Fix DT channel validation
mei: pull kvfree out of spinlock
rust_binder: do not query current thread for all ioctls
nvmem: layouts: Add fixed-layout driver
nvmem: apple-spmi-nvmem: wrap regmap calls to satisfy CFI
misc: fastrpc: fix memory leak in fastrpc_channel_ctx_free
misc: fastrpc: fix channel ctx ref leak when session alloc fails
misc: fastrpc: take fl->lock when moving mmaps on interrupted invoke
misc: fastrpc: Remove buffer from list prior to unmap operation
misc: fastrpc: Fix initial memory allocation for Audio PD memory pool
Pull fbdev fixes from Helge Deller:
"A few patches for the core fbdev layer which stabilize or fix
potential issues with text font rendering after screen rotation or
after user initiated font changes and locking fixes for sysfb during
modifications of the graphics mode database"
* tag 'fbdev-for-7.2-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/deller/linux-fbdev:
fbdev: bitblit: bound-check glyph index in bit_cursor()
fbdev: Fix out-of-bounds access when rotating console after font resize
fbdev: core: Fix pointer desynchronization in fb_io_read()
fbdev: serialize mode sysfs access with lock_fb_info()
fbdev: clear fb_info->mode before deleting a videomode
fbdev: bound mode sysfs output to the sysfs buffer
Pull driver core fixes from Danilo Krummrich:
- Fix Rust build failure on s390 by gating ioremap() / iounmap()
helpers and the io::mem module on CONFIG_HAS_IOMEM; gate affected
doctests as well.
- Add missing kernel-doc for show_const / store_const union members in
struct device_attribute.
* tag 'driver-core-7.2-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/driver-core/driver-core:
rust: io: gate ioremap doctests on CONFIG_HAS_IOMEM
rust: io: gate ioremap/iounmap on CONFIG_HAS_IOMEM
driver core: add missing kernel-doc for union members
Pull input updates from Dmitry Torokhov:
- Fixes for information leaks and OOB accesses across several drivers,
including evdev, focaltech, edt-ft5x06, iforce, and cs40l50-vibra
- Improvements to the synaptics-rmi4 driver to properly handle F54
worker errors and prevent buffer overflows
- Input validation fixes in the hynitron_cstxxx touchscreen driver to
prevent issues with invalid finger IDs and touch counts
- Fixes for use-after-free and initialization bugs in the byd mouse and
psxpad-spi drivers
- New quirks for the atkbd driver to make keyboard work on HONOR and
Xiaomi laptops
- Support for the ZENAIM LEVERLESS controller in the xpad driver.
* tag 'input-for-v7.2-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: evdev - sanitize event type index when fetching event masks
Input: synaptics-rmi4 - propagate F54 worker errors to V4L2 queue
Input: synaptics-rmi4 - block s_input when F54 queue is busy
Input: synaptics-rmi4 - bound the F54 report size to the allocated buffer
Input: synaptics-rmi4 - zero report size on F54 work error
Input: synaptics-rmi4 - fix F55 transmitter electrode count typo
Input: hynitron_cstxxx - validate touch count and finger IDs
Input: evdev - fix information leak in evdev_pass_values()
fixp-arith: convert comments to kernel-doc format
Input: focaltech - fix array out-of-bounds in focaltech_process_rel_packet
Input: atkbd - skip deactivate for HONOR ZQC-P
Input: atkbd - skip deactivate for Xiaomi Book Pro 14's internal keyboard
Input: iforce - validate input packet lengths
Input: psxpad-spi - set driver data before use
Input: cs40l50-vibra - validate custom data from user space
Input: xpad - add support for ZENAIM LEVERLESS
Input: edt-ft5x06 - ignore contacts with an out-of-range slot id
Input: byd - synchronize timer deletion before freeing private data
Pull powerpc fixes from Madhavan Srinivasan:
- A couple of fixes for a memory leak and a underflow case
Thanks to George Wilson and R Nageswara Sastry
* tag 'powerpc-7.2-4' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux:
powerpc/pseries: lparcfg - fix kbuf[] underflow
powerpc/pseries: pci - logic bug
powerpc/pseries: papr-phy-attest - validate cmd.length, plug mem leak
bit_cursor() fetches the glyph under the cursor with
c = scr_readw(vc_pos);
src = vc_font.data + ((c & charmask) * w * height);
where charmask is 0x1ff when vc_hi_font_mask is set. The screen buffer
value comes directly from scr_readw() and may be larger than the current
font's glyph count.
Syzkaller triggers this via vcs_write(). The Call Trace shows
vcs_write() in vc_screen.c writing an arbitrary 16-bit value with
writev() to /dev/vcsa, which vcs_write_buf() in vc_screen.c stores via
vcs_scr_writew() without checking charcount. The stored value is later
read in bit_cursor() in bitblit.c.
When the font is changed from a font with 512 glyphs to a font with
256 glyphs, the screen buffer can retain characters with the high
bit set from the previous mode, which could also produce the same
out-of-bounds access.
BUG: KASAN: global-out-of-bounds in soft_cursor+0x378/0x6bc drivers/video/fbdev/core/softcursor.c:70
Read of size 16 at addr ffff800086c57970
Call Trace:
soft_cursor+0x378/0x6bc drivers/video/fbdev/core/softcursor.c:70
bit_cursor+0xa90/0x1108 drivers/video/fbdev/core/bitblit.c:365
fbcon_cursor+0x344/0x498 drivers/video/fbdev/core/fbcon.c:1427
hide_cursor+0xdc/0x2d0 drivers/tty/vt/vt.c:883
update_region+0x100/0x18c drivers/tty/vt/vt.c:669
vcs_write+0x8ec/0xaf0 drivers/tty/vt/vc_screen.c:685
bit_putcs_aligned() and bit_putcs_unaligned() already clamp the glyph
index to vc_font.charcount. Apply the same clamp in bit_cursor() after
extracting the attribute and masking, before indexing fontdata.
The fix completes the bounds checking started in commit 18c4ef4e76
("fbdev: bitblit: bound-check glyph index in bit_putcs*"), which missed
the cursor path.
This change should be safe because the clamp reuses the existing
contract from fbcon: charcount is maintained under console_lock in
con_font_set() and fbcon_font_set(), and hi_font_mask is cleared when
switching from 512 to 256 glyphs. When stale screen data with high bits
remains after a font switch, or when vcs_write() stores an arbitrary
value, clamping the index to 0 prevents the out-of-bounds read without
changing cursor semantics — the same fallback bit_putcs uses.
Reported-by: syzbot+61b1db46218109869c14@syzkaller.appspotmail.com
Closes: https://syzkaller.appspot.com/bug?extid=61b1db46218109869c14
Link: https://lore.kernel.org/all/6a75205c.01d0871a.3a0d52.0032.GAE@google.com/
Fixes: 18c4ef4e76 ("fbdev: bitblit: bound-check glyph index in bit_putcs*")
Cc: stable@vger.kernel.org
Assisted-by: Hermes:muse-spark-1.2 syzkaller
Signed-off-by: Rik van Riel <riel@surriel.com>
Signed-off-by: Helge Deller <deller@gmx.de>
[BUG]
Recently, we encountered a KASAN warning as follows:
BUG: KASAN: slab-out-of-bounds in ccw_putcs+0x8bd/0xa80
Read of size 1 at addr ff11000110067100 by task bash/1209
CPU: 10 UID: 0 PID: 1209 Comm: bash Not tainted 7.2.0-rc3 #69 PREEMPT(full)
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.17.0-4.fc41 04/01/2014
Call Trace:
<TASK>
...
kasan_report+0xf0/0x120
? ccw_putcs+0x8bd/0xa80
ccw_putcs+0x8bd/0xa80
? __pfx_ccw_putcs+0x10/0x10
fbcon_putcs+0x338/0x410
? __pfx_ccw_putcs+0x10/0x10
do_update_region+0x21d/0x450
invert_screen+0x29d/0x5e0
? __kmalloc_noprof+0x493/0x640
? vc_do_resize+0x17c/0xe50
clear_selection+0x4c/0x60
vc_do_resize+0xaee/0xe50
fbcon_modechanged+0x2bd/0x640
rotate_all_store+0x298/0x380
...
reproduce:
1) issue two ioctls: first a KDFONTOP ioctl with op.op = KD_FONT_OP_SET,
op.width = 1 and op.height = 1, then a TIOCL_SETSEL ioctl
2) echo 2 > /sys/devices/virtual/graphics/fbcon/rotate_all
3) issue two ioctls: first a KDFONTOP ioctl with op.op = KD_FONT_OP_SET,
op.width = 8 and op.height = 1, then a TIOCL_SETSEL ioctl
4) echo 3 > /sys/devices/virtual/graphics/fbcon/rotate_all
[CAUSE]
The root cause is that fbcon_modechanged() first sets the current rotate's
corresponding ops. Subsequently, during vc_resize(), it may trigger
clear_selection(), and in fbcon_putcs->ccw_putcs[rotate=3], this can result
in an out-of-bounds access to "src". This happens because par->rotated.buf
is reallocated in fbcon_rotate_font():
1) When rotate=2, its size is (width + 7) / 8 * height
2) When rotate=3, its size is (height + 7) / 8 * width
And the call to fbcon_rotate_font() occurs after clear_selection(). In
other words, the fontbuffer is allocated using the size calculated from the
previous rotation 2, but before reallocating it with the new size,
con_putcs is already using the new rotation 3:
rotate_all_store
fbcon_rotate_all
fbcon_set_all_vcs
fbcon_modechanged
set_blitting_type
...
par->bitops = &ccw_fbcon_bitops
vc_resize
...
clear_selection
highlight
...
do_update_region
fbcon_putcs
...
image.dy = vyres - ((xx + count) * vc->vc_font.width) [1] // overflow!
ccw_putcs_aligned
// old buf size is still being used during the read!
src = par->rotated.buf + (scr_readw(s--) & charmask) * cellsize
fb_pad_aligned_buffer----[src KASAN!!!] [2]
info->fbops->fb_imageblit(info, image)
sys_imageblit
fb_imageblit
fb_address_forward
// offset: image->dy * bits_per_line + image->dx * bpp
unsigned int bits = (unsigned int)adr->bits + offset
adr->address += (bits & ~(BITS_PER_LONG - 1u)) / BITS_PER_BYTE [3]
fb_bitmap_imageblit
...
fb_read_offset // page fault! [4]
update_screen
redraw_screen
...
ccw_cursor
soft_cursor
memcpy(src, image->data, dsize)----[src KASAN again!!!] [5]
fbcon_switch
fbcon_rotate_font
font_data_rotate
dst = kmalloc_array(charcount, d_cellsize, GFP_KERNEL)
// the new size is allocated only here!
par->rotated.buf = buf [6]
[FIX]
A fairly obvious approach is to follow fbcon_switch(): in
fbcon_modechanged(), call rotate_font() before vc_resize() so that a
correctly sized buffer is allocated in time, as done in [6]. This fix is
necessary, but it is not sufficient on its own.
In [1] it causes an image.dy overflow (ccw_putcs: vyres = 768,
image.dy = 4294967040), because vc_cols has not been updated in time at
this point (it is likewise only updated after clear_selection()). This
allows (xx + count) * width to exceed vyres, causing image.dy to overflow.
Subsequently, address in [3] is incremented by an even larger amount, which
triggers a page fault at [4].
Therefore, a second fix is required in combination with the first: move
clear_selection() earlier, before set_blitting_type() in
fbcon_set_all_vcs(), to prevent the out-of-bounds access. fbcon_rotate()
has a similar problem, so add the same clear there. Since vc_is_sel() is
not exported, the fbdev side is currently forced to call clear_selection()
unconditionally, causing the global selection to be cleared prematurely.
And this will not cause any other significant impact.
Signed-off-by: Zizhi Wo <wozizhi@huawei.com>
Signed-off-by: Helge Deller <deller@gmx.de>
In fb_io_read(), if copy_to_user() performs a partial copy (e.g., due to
a faulty user buffer), the loop adjusts the chunk size 'c' and updates
the remaining 'count'. However, the hardware 'src' pointer has already
been eagerly advanced by the original chunk size.
If the loop is allowed to continue, the read will resume from an
incorrect, over-advanced offset. Since the remaining 'count' was only
decremented by the successful bytes, this desynchronization causes the
next iterations to execute more hardware reads than originally bounded,
eventually leading to out-of-bounds I/O reads.
Fix this by breaking out of the loop immediately upon a partial
copy_to_user(). A partial copy indicates a faulty user buffer, making
subsequent read attempts futile. Breaking out ensures we return the
number of successfully read bytes without risking out-of-bounds hardware
accesses in subsequent mismatched iterations.
Fixes: 6121cd9ef9 ("fbdev: Move I/O read and write code into helper functions")
Cc: stable@vger.kernel.org
Signed-off-by: Mingyu Wang <25181214217@stu.xidian.edu.cn>
Signed-off-by: Helge Deller <deller@gmx.de>
show_mode(), show_modes(), and store_mode() access fb_info->modelist
and fb_info->mode without holding lock_fb_info(). store_modes() takes
lock_fb_info() while replacing the modelist and freeing the old one.
A concurrent reader or writer can load a pointer to an old modelist
entry before store_modes() frees it, then dereference freed memory or
store a stale freed pointer in fb_info->mode.
Take lock_fb_info() in show_mode(), show_modes(), and store_mode() to
serialize with store_modes(). In show_mode(), copy the mode to the
stack and format after dropping the lock. In store_mode(), split
activate() into a _locked variant to avoid double-locking, and hold
the locks for the modelist walk, mode conversion, activation, and
fb_info->mode assignment together.
Cc: stable@vger.kernel.org # v7.1+
Signed-off-by: Melbin K Mathew <mlbnkm1@gmail.com>
Signed-off-by: Helge Deller <deller@gmx.de>
fb_set_var() can delete a mode from info->modelist when userspace
passes FB_ACTIVATE_INV_MODE through FBIOPUT_VSCREENINFO. The code
checks that the mode being deleted is not the current info->var and
that fbcon is not using it, but it does not check fb_info->mode.
fb_info->mode may still point into the modelist entry being deleted.
If the entry is freed, later mode sysfs reads through show_mode() can
dereference a stale pointer.
Clear fb_info->mode before calling fb_delete_videomode() when it
matches the mode being removed.
Cc: stable@vger.kernel.org # v7.1+
Signed-off-by: Melbin K Mathew <mlbnkm1@gmail.com>
Signed-off-by: Helge Deller <deller@gmx.de>
mode_string() uses snprintf() which can return a value larger than the
remaining buffer space. show_modes() accumulates the return value into i
without checking whether i has reached PAGE_SIZE, causing the offset to
advance past the sysfs buffer if the modelist is long enough.
Add a size parameter to mode_string() and use scnprintf() to return
only the bytes actually written. Add an early return when offset
already exceeds the buffer. In show_modes(), stop accumulating once
the buffer is full.
Cc: stable@vger.kernel.org # v7.1+
Signed-off-by: Melbin K Mathew <mlbnkm1@gmail.com>
Signed-off-by: Helge Deller <deller@gmx.de>
In lparcfg_write(), a count of 0 results in kbuf[] being indexed at -1.
Check for count == 0 in the existing check for count > sizeof(kbuf) and
return -EINVAL if true.
Fixes: 74422e2b19 ("powerpc/pseries: Remove VLA from lparcfg_write()")
Acked-by: Nayna Jain <nayna@linux.ibm.com>
Tested-by: R Nageswara Sastry <rnsastry@linux.ibm.com>
Cc: stable@vger.kernel.org # 4.20
Signed-off-by: George Wilson <gcwilson@linux.ibm.com>
Signed-off-by: Madhavan Srinivasan <maddy@linux.ibm.com>
In papr_phy_attest_create_handle(), the params->cmd.length is not
validated before use, which can result in a buffer overlow. Check it and
return -EINVAL if it is either 0 or exceeds sizeof(params->cmd).
Also, params is freed on the success path but not error. Free it on
errors after memory allocation. And free it on negative fd.
Fixes: 86900ab620 ("powerpc/pseries: Add a char driver for physical-attestation RTAS")
Acked-by: Haren Myneni <haren@linux.ibm.com>
Acked-by: Nayna Jain <nayna@linux.ibm.com>
Tested-by: R Nageswara Sastry <rnsastry@linux.ibm.com>
Cc: stable@vger.kernel.org # 6.16
Signed-off-by: George Wilson <gcwilson@linux.ibm.com>
Signed-off-by: Madhavan Srinivasan <maddy@linux.ibm.com>
Pull watchdog fixes from Guenter Roeck:
- at91sam9_wdt: prevent timer rearm during teardown
- bd96801_wdt: Fix timeout for enabled WDG
- atcwdt200: Fix return value when watchdog is enabled
* tag 'watchdog-for-v7.2-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging:
watchdog: at91sam9_wdt: prevent timer rearm during teardown
watchdog: bd96801_wdt: Fix timeout for enabled WDG
watchdog: atcwdt200: fix return value when watchdog is enabled
Pull ata fixes from Damien Le Moal:
- Disable link power management on yet another misbehaving WD drive
(Niklas)
- Fix a use after free issue in the pata_sl82c105 driver (Hongyan)
* tag 'ata-7.2-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/libata/linux:
ata: pata_sl82c105: fix bridge revision use-after-free
ata: libata-core: Disable LPM on WDC WD141KFGX-68FH9N0
Pull pin control fixes from Linus Walleij:
"Qualcomm fixes: some incorrectly defined groups in IPQ9650, two pins
needing to be marked as GPIO in IPQ806X"
* tag 'pinctrl-v7.2-3' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl:
pinctrl: qcom: ipq806x: mark pci reset as a GPIO pin function
pinctrl: qcom: ipq806x: mark gpio as a GPIO pin function
pinctrl: qcom: ipq9650: fix audio_sec_mclk_in1/out1 group pins
A task performing a custom private hash resize can remain blocked in
uninterruptible sleep indefinitely. The hung-task detector reports:
INFO: task futex-resizer:314 blocked for more than 10 seconds.
task:futex-resizer state:D stack:14824 pid:314 tgid:312 ppid:311
Call Trace:
__schedule+0x521/0xf30
schedule+0x22/0xa0
futex_hash_allocate+0x3db/0x490
__do_sys_prctl+0x6f5/0xbd0
do_syscall_64+0xf9/0x530
entry_SYSCALL_64_after_hwframe+0x77/0x7f
Kernel panic - not syncing: hung_task: blocked tasks
futex_pivot_pending() allows the resize request to continue when
either no replacement hash is pending (hash_new == NULL) or the current
hash reference count has reached zero.
After the final-reference wake, another futex task can complete the
pivot between the two observations:
T1 T2
futex_hash_allocate()
wait_var_event(mm, ...)
futex_pivot_pending(mm)
hash_new != NULL
futex_hash()
futex_ref_get(old) -> false
futex_pivot_hash(mm)
hash_new = NULL
__futex_pivot_hash(mm, new)
rcu_assign_pointer(hash, new)
fph = rcu_dereference(hash) /* new */
futex_ref_is_dead(fph) -> false
schedule()
The pivot changes the state from hash_new != NULL with a dead current
hash to hash_new == NULL with a live current hash. Because
futex_pivot_pending() reads hash_new and hash without serialization,
the resize task can observe hash_new in the pre-pivot state and hash in
the post-pivot state, causing futex_pivot_pending() to return false even
though the pivot has completed. The task then goes to sleep after the
wakeup has already been consumed.
Serialize state reads in futex_pivot_pending() using futex_mm_phash::lock.
This guarantees that futex_pivot_pending() observes hash_new and hash
atomically, eliminating the race condition.
Fixes: bd54df5ea7 ("futex: Allow to resize the private local hash")
Suggested-by: Peter Zijlstra <peterz@infradead.org>
Signed-off-by: Yao Kai <yaokai34@huawei.com>
Signed-off-by: Thomas Gleixner <tglx@kernel.org>
Cc: stable@vger.kernel.org
Link: https://patch.msgid.link/20260804125530.3933754-1-yaokai34@huawei.com
Pull BPF fixes from Daniel Borkmann:
- Fix BPF verifier to preserve full pointer state for commuted
scalar += pointer arithmetic (Yiyang Chen, Eduard Zingerman)
- Fix a use-after-free of request sockets in the BPF TCP iterator
batching (Jose Fernandez)
- Fix a use-after-free of sk_redir in the BPF sockmap send verdict
path (Chengfeng Ye)
- Fix a netns reference imbalance in the BPF conntrack kfuncs
(Chengfeng Ye)
- Fix bpf_get_fsverity_digest() dynptr assumptions and silent
digest truncation (Eric Biggers)
- Fix bpf_tcp_{gen,check}_syncookie to check sk_state before
sk_protocol to make sure it is a full socket (Luxiao Xu)
- Fix rqspinlock to reset the tail when preserving the queue
on deadlock (Kumar Kartikeya Dwivedi)
* tag 'bpf-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/bpf/bpf:
rqspinlock: Reset tail when preserving queue on deadlock
bpf: Check sk_state before sk_protocol in bpf_tcp_*_syncookie
fsverity: Fix silent truncation in bpf_get_fsverity_digest()
fsverity: Fix bpf_get_fsverity_digest() dynptr assumptions
bpf: tcp: Fix use-after-free in bpf_iter_tcp_established_batch()
bpf: Fix netns reference imbalance in conntrack kfuncs
bpf, sockmap: Fix sk_redir use-after-free in send verdict
selftests/bpf: Cover commuted pointer state propagation
bpf: Propagate untrusted pointer state in commuted arithmetic
bpf: Preserve pointer state for commuted arithmetic
bpf: Simplify sanitize_err() signature
Pull vkm fixes from Paolo Bonzini:
"s390:
- fix a lot of small bugs and races
x86:
- fix missing locking related to KVM_CAP_MOVE_ENC_CONTEXT_FROM
- warn on creating a new page table that is the child of an invalid
one, and limit damage before it's too late
- disable use of INVLPGA when NPT is enabled, because it doesn't seem
to flush TLBs correctly"
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm: (26 commits)
KVM: x86/mmu: WARN and clear role.invalid when creating a child shadow page
KVM: SVM: Serialize accesses to the owner and mirror list with separate lock
KVM: SVM: make svm_flush_tlb_gva do a full asid flush if NPT enabled
KVM: s390: Fix cleanup in kvm_s390_pv_create_cpu()
KVM: s390: Fix ordering when adding to SCA
KVM: s390: Return -EINTR if a signal is pending while faulting-in
KVM: s390: Free the mmu cache when kvm_arch_vcpu_create() fails
KVM: s390: ucontrol: Add missing locking around gmap_remove_child()
KVM: s390: cmma: Fix dirty tracking when removing memslot
KVM: s390: Fix race in __do_essa()
KVM: s390: Fix leaking of PGM_ADDRESSING to userspace
KVM: s390: ucontrol: Fix sca_clear_ext_call()
KVM: s390: Fix overclearing ESCA in case of error
KVM: s390: Fix kvm_s390_vcpu_unsetup_cmma()
KVM: s390: Do not free SCA if it was not allocated
KVM: s390: Fix unlikely NULL gmap dereference
s390/vfio_ccw: Implement a crw lock
s390/vfio_ccw: Selectively expand io_mutex
s390/vfio_ccw: Move cp cleanup out of not operational
s390/vfio_ccw: Cancel existing workqueues
...
Pull thermal control fixes from Rafael Wysocki:
"Revert three thermal core updates, two recent ones and one older.
The recent ones attempted to fix a design issue in the thermal core
and simplify code on top of that, but they made changes visible to
user space and made it unhappy.
The older one is a misguided code cleanup that introduced a
(potentially nasty) bug"
* tag 'thermal-7.2-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
Revert "thermal/drivers/hwmon: Cleanup coding style a bit"
Revert "thermal: hwmon: Register a hwmon device for each thermal zone"
Revert "thermal: hwmon: Use extra_groups for adding temperature attributes"
Pull sound fixes from Takashi Iwai:
"A collection of small fixes since the last pull request. More than
few, but an enough-manageable amount at this time.
USB-audio:
- UAF, OOB and such hardening fixes for USB-audio, usx2y and
us144mkii
- Mixer regression fixes for Logitech PRO X 2 LIGHTSPEED headset and
M-Audio Fast Track Ultra
HD-audio:
- Fix for an ACPI reference leak in TAS2781 HDA side-codec
ASoC:
- Fixes the default tables for Cirrus Logic codecs
- Fixes for invalid enum accesses for Qualcomm LPASS
- Error handling and robustness fixes for Intel SOF & Soundwire
- DMI quirks for a few AMD devices"
* tag 'sound-7.2-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound: (22 commits)
ALSA: usb-audio: Fix sticky mixer regressions on M-Audio Fast Track Ultra
ASoC: cs4265: sort the register default table
ASoC: cs35l45: sort the register default table
ASoC: cs35l41: sort the register default table
ASoC: amd: yc: Add DMI quirk for MSI Raider A18 HX A7VHG
ASoC: amd: yc: Add DMI quirk for Xiaomi RedmiBook 16 2025
ALSA: usx2y: bound the hwdep mmap fault offset
ALSA: usb-audio: fix OOB write on Type II inbound URBs
ALSA: us144mkii: re-anchor capture URBs on resubmission
ALSA: FCP: fix OOB write in fcp_meter_ctl_get()
MAINTAINERS: add SpacemiT K1/K3 I2S entry
ASoC: rt5645: Make the Kconfig symbol user selectable
ALSA: usb-audio: Add QUIRK_FLAG_MIXER_GET_CUR_BROKEN for Logitech PRO X 2 LIGHTSPEED
ALSA: hda/tas2781: fix ACPI reference handling
ASoC: codecs: lpass-wsa-macro: Fix enum kcontrol accesses
ASoC: codecs: lpass-tx-macro: Fix enum kcontrol accesses
ASoC: SOF: ipc4-pcm: Continue the pipeline trigger in case of IPC timeout
ASoC: amd: yc: Add DMI quirk for HP Victus Laptop 16-e1xxx
ASoC/soundwire: Intel: reset the PCMSyCM registers in hda_sdw_bpt_close
ASoC: SOF: sof-audio: Fix error path in sof_widget_setup_unlocked()
...
The recent fix for sticky mixer volumes caused regressions of M-audio
Fast Track Ultra device, where the mixer state is kept to the default
value.
Add the quirk entries to tolerate the broken mixer behavior. As the
device is known to work in the implicit feedback mode, explicitly
enable the implicit feedback mode, too.
Since there are two FTU models that are almost identical, both entries
are added in this patch (0763:2080 and 0763:2081).
Fixes: 86aa1ea1f1 ("ALSA: usb-audio: Do not expose sticky mixers")
Link: https://bugzilla.suse.com/show_bug.cgi?id=1273166
Link: https://patch.msgid.link/20260807083418.1712585-1-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Explicitly clear role.invalid when deriving a child shadow page's role from
its parent to harden against bugs elsewhere in KVM, as violating KVM's
invariant that invalid pages are NOT on the list of active MMU pages leads
to use-after-free due to __kvm_mmu_prepare_zap_page() using list_add()
instead of list_move() when processing an invalid shadow page, i.e. makes a
bad situation far worse.
Yell loudly if the parent is invalid, as it means KVM has missed a validity
check, i.e. KVM is attempting to map memory using an invalid/obsolete root,
but continue on as the child is otherwise still a valid shadow page.
==================================================================
BUG: KASAN: slab-use-after-free in __kvm_mmu_get_shadow_page+0x1817/0x1860 [kvm]
Write of size 8 at addr ff11000153dd1368 by task repro/853
CPU: 1 UID: 1000 PID: 853 Comm: repro Not tainted 7.2.0-rc2-3aec122bdcaf-next-vm #5 PREEMPT
Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS 0.0.0 02/06/2015
Call Trace:
<TASK>
dump_stack_lvl+0x4b/0x70
print_report+0x153/0x49c
kasan_report+0xbc/0xf0
__kvm_mmu_get_shadow_page+0x1817/0x1860 [kvm]
mmu_alloc_root+0x141/0x320 [kvm]
kvm_mmu_load+0x612/0x20f0 [kvm]
kvm_arch_vcpu_ioctl_run+0x3dd5/0x6150 [kvm]
kvm_vcpu_ioctl+0x5e4/0x10d0 [kvm]
__x64_sys_ioctl+0x131/0x1b0
do_syscall_64+0x67/0x5f0
entry_SYSCALL_64_after_hwframe+0x4b/0x53
</TASK>
Allocated by task 853:
kasan_save_stack+0x20/0x40
kasan_save_track+0x14/0x30
__kasan_slab_alloc+0x5f/0x70
kmem_cache_alloc_noprof+0xfe/0x2e0
__kvm_mmu_topup_memory_cache+0x135/0x530 [kvm]
paging64_page_fault+0x318/0x1e30 [kvm]
kvm_mmu_do_page_fault+0x21d/0x630 [kvm]
kvm_mmu_page_fault+0x18c/0x17b0 [kvm]
kvm_arch_vcpu_ioctl_run+0x1f35/0x6150 [kvm]
kvm_vcpu_ioctl+0x5e4/0x10d0 [kvm]
__x64_sys_ioctl+0x131/0x1b0
do_syscall_64+0x67/0x5f0
entry_SYSCALL_64_after_hwframe+0x4b/0x53
Freed by task 853:
kasan_save_stack+0x20/0x40
kasan_save_track+0x14/0x30
kasan_save_free_info+0x3b/0x60
__kasan_slab_free+0x43/0x70
kmem_cache_free+0xe2/0x400
kvm_mmu_commit_zap_page.part.0+0x1e2/0x310 [kvm]
kvm_mmu_free_roots+0x283/0x560 [kvm]
kvm_arch_vcpu_ioctl_run+0x33c8/0x6150 [kvm]
kvm_vcpu_ioctl+0x5e4/0x10d0 [kvm]
__x64_sys_ioctl+0x131/0x1b0
do_syscall_64+0x67/0x5f0
entry_SYSCALL_64_after_hwframe+0x4b/0x53
Reported-by: Hyunwoo Kim <imv4bel@gmail.com>
Fixes: a770f6f28b ("KVM: MMU: Inherit a shadow page's guest level count from vcpu setup")
Cc: stable@vger.kernel.org
Signed-off-by: Sean Christopherson <seanjc@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
In corsairpsu_linear11_to_int(), the mantissa is extracted using bitwise
operations and cast to s16 before being shifted left:
static int corsairpsu_linear11_to_int(const u16 val, const int scale)
{
...
const int mant = (((s16)(val & 0x7ff)) << 5) >> 5;
...
}
Due to C integer promotion rules, the masked value (which is always
positive) is promoted to a 32-bit integer before the left shift. As a
result, the sign bit is never extended to bit 31 of the promoted integer.
When the device hardware reports a negative temperature in Linear11 format
(such as an ambient temperature probe reporting sub-zero), the negative
mantissa is parsed incorrectly as a massive positive value. For example,
-1 becomes 2047, which scales to 2047 degrees Celsius.
Fix the problem by type casting the result of the left shift operation
to s16.
Another problem is left-shifting of negative values. In C, the result of
left-shifting negative values is undefined. Use a multiplication instead
to avoid the problem.
Also use a local s64 variable to store temporary results, change
the return value type from int to long, and clamp the final value
to LONG_MIN and LONG_MAX to avoid under- and overflow issues while
retaining as much information as possible.
Reported-by: Sashiko <sashiko-bot@kernel.org>
Cc: Wilken Gottwalt <wilken.gottwalt@posteo.net>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Tested-by: Wilken Gottwalt <wilken.gottwalt@posteo.net>
Link: https://lore.kernel.org/r/20260804034811.2385506-1-linux@roeck-us.net
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
corsairpsu_request() sends a rail select command and then the actual
read as two separate transfers, both going through the single shared
cmd_buffer and wait_completion in corsairpsu_usb_cmd(). The hwmon core
serializes its own callers, but the debugfs files call
corsairpsu_get_value() directly and never take that lock, so a debugfs
read can land between another reader's rail select and its value read.
The result is a value from the wrong rail reported as the right one,
because corsairpsu_usb_cmd() only checks the command echo and both
transfers echo the command it expects. It can also make a caller consume
the reply meant for the other one, since raw_event() writes into the
shared buffer and completes whoever happens to be waiting.
Locking was dropped in commit 4207069edb ("hwmon: (corsair-psu) Rely
on subsystem locking") on the grounds that the subsystem serializes for
us, which holds for sysfs but not for these files. Take
the same lock in the debugfs paths that issue commands, using the guard
added in commit d1e720c732 ("hwmon: Support guard() and scoped_guard
for subsystem locks").
The lock cannot go into corsairpsu_request() itself: the hwmon core
already holds it across ->read, so every sysfs read would deadlock.
vendor_show() and product_show() only print strings cached during probe
and issue no command, and corsairpsu_get_criticals() and
corsairpsu_check_cmd_support() run before either interface is
registered, so none of them need it.
Fixes: 4207069edb ("hwmon: (corsair-psu) Rely on subsystem locking")
Signed-off-by: Ali Ahmet Memis <ali@iusegentoo.com>
Tested-by: Wilken Gottwalt <wilken.gottwalt@posteo.net>
Link: https://lore.kernel.org/r/20260806142139.168611-1-ali@iusegentoo.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
ltc4282_parse_dt() evaluates the wrong variable when parsing the current
limit.
When the adi,current-limit-sense-microvolt property is parsed into
st->vsense_max, the subsequent switch statement evaluates the unrelated
val variable instead of st->vsense_max:
drivers/hwmon/ltc4282.c:ltc4282_parse_dt() {
...
ret = device_property_read_u32(dev, "adi,current-limit-sense-microvolt",
&st->vsense_max);
if (!ret) {
int reg_val;
switch (val) {
case 12500:
reg_val = 0;
break;
...
}
Because val holds a small integer representing vin_mode (from 0 to 3), it
never matches any of the valid current limit cases.
This causes it to always fall through to the default error case, return
-EINVAL, and aborts probe initialization for any device tree using this
property.
Validate st->vsense_max instead to fix the problem.
Reported-by: Sashiko <sashiko-bot@kernel.org>
Fixes: cbc29538db ("hwmon: Add driver for LTC4282")
Cc: Nuno Sa <nuno.sa@analog.com>
Reviewed-by: Nuno Sá <nuno.sa@analog.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
When a negative value is passed to ltc4282_write_curr(), the signed long
val is cast directly to u64:
drivers/hwmon/ltc4282.c:ltc4282_write_curr() {
/* need to pass it in millivolt */
u32 in = DIV_ROUND_CLOSEST_ULL((u64)val * st->rsense, DECA * MICRO);
...
}
This cast converts negative inputs into large positive values. The
subsequent division result overflows the u32 in variable, truncating
to a pseudo-random positive value. When this is passed to
ltc4282_write_voltage_byte(), it is clamped to the maximum limit instead
of zero.
Clamp val to 0 and to the maximum supported upper limit before the cast
and assign the result to a 64-bit temporary variable before the division
to avoid the underflow and an also possible overflow.
Reported-by: Sashiko <sashiko-bot@kernel.org>
Fixes: cbc29538db ("hwmon: Add driver for LTC4282")
Cc: Nuno Sa <nuno.sa@analog.com>
Reviewed-by: Nuno Sá <nuno.sa@analog.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
During device initialization in ltc4282_set_max_limits(), the calculation
of the maximum power limit can suffer from a 32-bit integer overflow.
static int ltc4282_set_max_limits(struct ltc4282_state *st)
{
...
st->power_max = DIV_ROUND_CLOSEST(st->vsense_max * DECA * MILLI,
st->rsense) * st->vfs_out;
...
}
The result of DIV_ROUND_CLOSEST() evaluates to a 32-bit unsigned integer
on 32-bit architectures. This result is then multiplied by st->vfs_out,
which is a 16-bit unsigned integer. According to C promotion rules, since
both operands are 32-bit or smaller, the multiplication is performed in
32-bit precision.
If the device is configured with a low sense resistor value via the device
tree (for example, 100 nano-ohms, resulting in st->rsense = 1) and the
voltage is high, the division result can reach 343,750,000 and st->vfs_out
can be 33,280. The product of these values is approximately 11.44 trillion,
which exceeds the maximum capacity of a 32-bit integer and overflows
before being stored in st->power_max.
This overflow causes a truncated value to be assigned to st->power_max and
written to the hardware limit register. An incorrect maximum power limit
can trigger spurious power-bad faults or alarms, which may lead to the
shutdown of the monitored power rail.
Avoid the problem by calculating and storing the maximum power using 64-bit
variables.
Reported-by: Sashiko <sashiko-bot@kernel.org>
Fixes: cbc29538db ("hwmon: Add driver for LTC4282")
Cc: Nuno Sa <nuno.sa@analog.com>
Reviewed-by: Nuno Sá <nuno.sa@analog.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The driver currently has two issues with the external VREF regulator
handling in ads7828_probe():
1. All errors from devm_regulator_get_optional() are ignored, causing the
driver to incorrectly fall back to internal VREF even for transient
errors like -EPROBE_DEFER or genuine failures like -ENOMEM.
2. The external regulator is never enabled. The driver calls
regulator_get_voltage() without first calling regulator_enable(),
so the VREF pin may remain unpowered if the regulator is not
configured as always-on.
Fix both issues by switching to devm_regulator_get_enable_read_voltage(),
which handles regulator get, enable, and voltage read in one call.
Only -ENODEV (no regulator specified in device tree) should trigger the
fallback to internal VREF. All other errors are propagated to the caller.
Fixes: a8ddfea095 ("hwmon: (ads7828) Accept optional parameters from device tree")
Signed-off-by: Qingshuang Fu <fuqingshuang@kylinos.cn>
Link: https://lore.kernel.org/r/20260805061645.1331652-1-fffsqian@163.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
In theory it could be possible that the REPLY_SIZE sized buffers for
holding the vendor and product strings could be end up missing the null
termination (for example by malicious hardware built on purpose)
required by the seq_printf() call. That limits the debugfs printf calls
to a maximum string length of REPLY_SIZE.
Fixes: d115b51e0e ("hwmon: add Corsair PSU HID controller driver")
Signed-off-by: Wilken Gottwalt <wilken.gottwalt@posteo.net>
Link: https://lore.kernel.org/r/anLj9gPWRoRDbQBV@monster.localdomain
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Pull MM fixes from Andrew Morton:
"17 hotfixes. 15 are cc:stable. 16 are for MM.
There's a patch series from Lorenzo "mm: fix UAF caused by race
between ptdump and vmap pgtable freeing" which addresses a quite old
bug in the ptdump code.
And another series also from Lorenzo which fixes a four year old bug
in the huge_zero_folio handling.
A series from SJ fixes a few possible divide-by-zero issues which
Sashiko sniffed out. And a series which fixes handling of the
commit_inputs parameters.
The remainder are singletons, please see their changelogs for details"
* tag 'mm-hotfixes-stable-2026-08-06-18-44' of git://git.kernel.org/pub/scm/linux/kernel/git/akpm/mm:
mm/damon: adjust isolated pages stat for DAMOS_MIGRATE_{HOT,COLD}
mm/damon/ops-common: putback folios on invalid migrate nid
mm/huge_memory: initialise workingset state before folio split
mm/page_table_check: skip special zero mappings
mm/damon/lru_sort: skip damon_call() if ctx has not started
mm/damon/reclaim: skip damon_call() if ctx has not started
mm/damon/lru_sort: error out for >10000 active_mem_bp
samples/damon/mtier: error out for zero quota goal target values
mailmap: map old addresses to Danila Tikhonov
mm/huge_memory: separate out CONFIG_PERSISTENT_HUGE_ZERO_FOLIO logic
mm/huge_memory: fix huge_zero_pfn race
MAINTAINERS: update address for Brendan Jackman
mm/filemap: __filemap_add_folio() restore index before retrying
microblaze: restore the page alignment of swapper_pg_dir
arm64: remove redundant concurrent ptdump UAF mitigation
mm/ptdump: always stabilise against page table freeing using init_mm
mm/vmalloc: acquire init_mm lock on huge vmap to avoid ptdump UAF
Pull smb server fixes from Steve French:
- Reject Pattern_V1 payloads when Pattern_V1 support was not
negotiated
- Validate compression transform flags and chained mode before
allocating the decompression buffer
- Enforce the pre-authentication PDU size limit before allocating
the decompression buffer, preventing compressed requests from
bypassing the limit
* tag 'v7.2-rc6-smb3-server-fixes' of git://git.samba.org/ksmbd:
ksmbd: apply the pre-authentication PDU limit when decompressing
ksmbd: validate compression Flags before kvmalloc
smb: compress: reject Pattern_V1 when not negotiated
Currently, the destruction of the waiter queue is suppressed for
rqspinlock in cases where a deadlock is detected. Deadlock checks happen
relatively frequently (on entry for AA, within 1ms for ABBA), and waiter
threads may not be involved in locking scenarios involving deadlocks.
Thus, it is useful to not flush the queue and let other waiters take a
stab at acquiring the lock after we detect a deadlock and exit.
However, we need to follow the same logic as what we did previously for
the waitq_timeout label: reset the tail, and if we cannot, signal the
next waiter appropriately. In case of deadlocks, this signal would just
mark the MCS node as unlocked, and in case of timeouts, it would signal
RES_TIMEOUT_VAL. The difference thus is in the value propagated, which
decides whether the queue remains active or gets flushed.
Not doing the tail reset, and waiting for the next waiter can lead to
cases where we are the final waiter, and thus no next waiter arrives,
leading to intermittent stalls in this path. Once the next waiter does
join, we will be unblocked. In the theoretical case when the next waiter
never joins, we risk stalling indefinitely.
This can only happen for ABBA deadlocks, since entry into the wait queue
is guarded with AA checks. A precise sequence of executions leading up
to this scenario can be:
CPU 0 holds lock A.
CPU 1 holds lock B.
CPU 2 attempts lock B, becomes the pending waiter for B.
CPU 0 attempts lock B. B has locked+pending bits set, thus CPU 0 queues.
CPU 1 attempts lock A.
CPU 0 detects an ABBA deadlock.
Once deadlock detection happens for CPU 0, it will sit waiting for the
next waiter in the queue to populate node->next, which will experience
delays until such a waiter arrives.
Fix this by adjusting the logic for the check for deadlocks preceding
the waitq_timeout label. It would make sense to consolidate code for
both cases and use 'ret' to distinguish the value being propagated, but
that is left as an exercise for a future refactoring task to avoid diff
noise in this patch.
Fixes: 7bd6e5ce5b ("rqspinlock: Disable queue destruction for deadlocks")
Signed-off-by: Kumar Kartikeya Dwivedi <memxor@gmail.com>
Link: https://patch.msgid.link/20260802021759.1139457-1-memxor@gmail.com
Signed-off-by: Eduard Zingerman <eddyz87@gmail.com>
Pull smb client fixes from Steve French:
- Fix potential use after free in cifs_try_adding_channels
- Fix SMB1 large directory enumeration
- Minor debug improvement (show compress mount option)
* tag 'v7.2-rc6-smb3-client-fixes' of git://git.samba.org/sfrench/cifs-2.6:
smb: client: fix SMB1 TRANS2 multi-response truncation in SendReceive()
smb: client: Fix use-after-free in cifs_try_adding_channels()
smb/client: show compress mount option
at91_ping() rearms the watchdog timer from its callback. timer_delete()
neither waits for a running callback nor prevents it from rearming the
timer, so probe failure or driver removal can leave the timer accessing the
devm-allocated at91wdt after it has been freed.
Use timer_shutdown_sync() on both teardown paths. It waits for a running
callback and rejects any attempt by the callback to rearm the timer.
Fixes: 5161b31dc3 ("watchdog: at91sam9_wdt: better watchdog support")
Signed-off-by: Hongyan Xu <getshell@seu.edu.cn>
Link: https://lore.kernel.org/r/20260806060613.1830-1-getshell@seu.edu.cn
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Pull Btrfs Fixes 2: Electric Boogaloo from David Sterba:
"This brings back the fixup worker infrastructure.
It's a mechanism to detect pages/folios that are marked dirty without
filesystem knowledge and require COW fixup. The consequence of not
doing so is silent data loss.
The first patch covers the scenarios in detail, also reflecting folio
API port and subpage block size support added in recent years. The
original fixup worker was only for pages.
The patch is relatively big, half of the code is debugging and support
code, the rest is the core design around the detection and fix.
The second patch handles an unlikely case when there's work left
during unmount"
* tag 'for-7.2-rc6-fixup-worker-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/kdave/linux:
btrfs: flush the fixup workers during close_ctree
btrfs: trigger cow fixup via dirty_folio()
Pull btrfs fixes from David Sterba:
- fix leak in encoded ioctl write
- disable large folios on systems with highmem
- disable block size > page size when there's no transparent hugepage
support (under experimental config)
- reject compressed inline extents without valid LZO headers
- properly initialize cached inode mapping (if block size > page size)
* tag 'for-7.2-rc6-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/kdave/linux:
btrfs: initialize inode mapping flags for cached inodes
btrfs: disable bs > ps support if no transparent hugepage support
btrfs: fix memory leak in btrfs_do_encoded_write()
btrfs: lzo: reject inline extents without valid headers
btrfs: disable large folios for systems with highmem
Pull networking fixes from Jakub Kicinski:
"Including fixes from netfilter.
Looks like our attempt to keep the PRs smaller have only prevented
this one from getting even bigger. In the last 9 days there were
405 postings explicitly tagged with [PATCH net], vs 687 with [PATCH
net-next]. 37% of posted patches being fixes is pretty crazy, and
that's likely undercounting because LLM "researchers" more often post
fixes without knowing to tag the patches for specific trees. I don't
have historic data.
In any case, we keep adjusting the criteria. The next PR will be
smaller.
Current release - regressions:
- net: defer netdev KOBJ_ADD uevent until the device is published,
previously rtnl_lock would serialize the accesses vs publishing
- net: explicitly cancel work to avoid races with ref tracker exit
- qrtr: ns: raise lookup limit to 128
- eth: hns3: fix speed configuration residue after driver reload
Previous releases - regressions:
- tcp: do not change rcv_ssthresh in tcp_measure_rcv_mss(), regressed
flows with MSS and scaling_ratio variability
- Revert "net: thunderbolt: Enable end-to-end flow control also in
transmit", broke some platforms (no packets coming thru)
- eth: stmmac: resume PHY before hardware setup when opening the
interface
Previous releases - always broken:
- another pile of fixes for less common protocols (SCTP, TLS, SMC
etc.)
- close a couple of AF_PACKET bugs and ways it can build skbs
problematic for the rest of the stack
- bridge: mrp: fix uninitialised bytes on the wire
- net: devmem: prevent net-iov / page mixing, avoid crashes
- eth: atlantic: free RX pages of consumed but not refilled buffers"
* tag 'net-7.2-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (116 commits)
igc: fix netdev not re-attached after resume if interface is down
tls: don't abort the connection on signal-interrupted sends
net: avoid theoretical races with ref drain
net: Defer netdev KOBJ_ADD uevent until the device is published
MAINTAINERS: dpll: zl3073x: replace Prathosh Satish with Min Li
sctp: clear control chunk transport if it is being removed
net/atm: fix slab-out-of-bounds read in vcc_setsockopt()
s390/ism: Fix UAF of sba and ieq during ism_dev_exit()
packet: use consistent hard_header_len in TX_RING send path
packet: use consistent hard_header_len in non-ring send paths
net: remove CAP_SYS_RAWIO zero-padding in dev_validate_header
bnge: Fix resource leak in bnge_init_nic() error path
ptp: ocp: Fix board ID over-read
tls: rx: restore msg_iter before TLS 1.3 optimistic retry
selftests: tls: add a test for splicing onto a full plaintext record
tls: don't leave a full plaintext sk_msg ring unpushed
xdp: reject clones that overrun skb_shared_info tailroom
mptcp: reclaim forward-allocated memory on RX path errors
mptcp: fastopen: only mark MPTFO subflows with SYN data
mptcp: pm: fix memory leak from alloc-during-teardown race
...
amdgpu_dm_crtc_set_static_screen_optimze() maps sso_enable to the
Replay and PSR1 vsync events. allow_sr_entry is an entry gate, but the
helper currently applies it to both directions.
A non-fast update clears allow_sr_entry. During a modeset, a separate
hardware-programming event keeps self-refresh blocked while the stream
is reprogrammed. If vblank is enabled before the entry delay expires,
the ISM calls the helper with sso_enable false. The early return drops
the disable request, so the vsync events are not set.
After enough fast commits, allow_sr_entry becomes true and the
hardware-programming event can be cleared. Since the vblank reference
remains held, there is no further zero-to-one vblank transition to
restore the missing vsync events. Replay or PSR1 can then become active
while vblank is still enabled.
Gate only requests that enable static-screen optimization. Always
process disable requests so a vblank requestor keeps Replay and PSR1
blocked.
On a Phoenix system, repeated SDDM-to-VT handoffs produced stuck flips
followed by flip_done and commit-wait timeouts. The timeout was not
observed with this change applied.
Fixes: 3c108046e1 ("drm/amd/display: Add power module on Linux")
Assisted-by: Codex:gpt-5.6-sol
Assisted-by: Claude:opus-5
Signed-off-by: David Weber <weber.aulendorf@gmail.com>
Reviewed-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
(cherry picked from commit bd0c009821)
Cc: stable@vger.kernel.org
amdgpu_pci_remove() calls drm_dev_unplug() before invoking the fini
routines. After drm_dev_unplug() the drm_dev_enter() guard in
amdgpu_ttm_fini() always returns false, so iounmap() for
aper_base_kaddr is silently skipped. On connected_to_cpu hardware
ioremap_cache() maps the aperture as WB; when iounmap() is skipped the
stale WB PAT entry persists. On reload IP discovery's
memremap(MEMREMAP_WC) on the same aperture range hits a WB/WC conflict,
producing an ioremap error and failing re-probe.
Remove the drm_dev_enter() guard and call iounmap() unconditionally.
The aperture mapping is plain MMIO and does not require device-presence
protection. Surprise-removal cleanup of aper_base_kaddr is already
handled unconditionally by amdgpu_device_unmap_mmio().
Fixes: 62d5f9f711 ("drm/amdgpu: Unmap MMIO mappings when device is not unplugged")
Signed-off-by: Asad Kamal <asad.kamal@amd.com>
Reviewed-by: Lijo Lazar <lijo.lazar@amd.com>
Reviewed-by: Hawking Zhang <Hawking.Zhang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
(cherry picked from commit fb3f68af9f)
Cc: stable@vger.kernel.org
