The main driver for this change is the AD7607 part, which has a scale of
"1.220703" for the ±10V range. The AD7607 has a resolution of 14-bits.
So, just adding the scale-available list for that part would require some
quirks to handle just that scale value.
But to do it more neatly, the best approach is to rework the scale
available lists to have the same format as it is returned to userspace.
That way, we can also get rid of the allocation for the 'scale_avail_show'
array.
Signed-off-by: Alexandru Ardelean <aardelean@baylibre.com>
Reviewed-by: David Lechner <dlechner@baylibre.com>
Link: https://patch.msgid.link/20241025095939.271811-4-aardelean@baylibre.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
When the mutexes were reworked to guards, the caching of the
oversampling_ratio values was removed by accident.
The main effect of this change is that, after setting the
oversampling_ratio value, reading it back would result in the initial value
(of 1).
The value would get sent to the device correctly though.
Fixes 2956979dbd: ("iio: adc: ad7606: switch mutexes to guard")
Signed-off-by: Alexandru Ardelean <aardelean@baylibre.com>
Reviewed-by: David Lechner <dlechner@baylibre.com>
Link: https://patch.msgid.link/20241025095939.271811-2-aardelean@baylibre.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Add support for AD7770, AD7771, AD7779 ADCs. The device is capable of
sending out data both on DOUT lines interface,as on the SDO line.
The driver currently implements only the SDO data streaming mode. SPI
communication is used alternatively for accessing registers and streaming
data. Register accesses are protected by crc8.
Signed-off-by: Ramona Alexandra Nechita <ramona.nechita@analog.com>
Link: https://patch.msgid.link/20241014143204.30195-4-ramona.nechita@analog.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Until now, the conversion were triggered by setting high the GPIO
connected to the convst pin. This commit gives the possibility to
connect the convst pin to a PWM.
Connecting a PWM allows to have a better control on the samplerate,
but it must be handled with care, as it is completely decorrelated of
the driver's busy pin handling.
Hence it is not recommended to be used "as is" but must be exploited
in conjunction with IIO backend, and for now only a mock functionality
is enabled, i.e PWM never swings, but is used as a GPIO, i.e duty_cycle
== period equals high state, duty_cycle == 0 equals low state.
This mock functionality will be disabled after the IIO backend usecase
is introduced.
Signed-off-by: Guillaume Stols <gstols@baylibre.com>
Link: https://patch.msgid.link/20241015-ad7606_add_iio_backend_support-v5-4-654faf1ae08c@baylibre.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Add the required properties for iio-backend support, as well as an
example and the conditions to mutually exclude interruption and
conversion trigger with iio-backend.
The iio-backend's function is to controls the communication, and thus the
interruption pin won't be available anymore.
As a consequence, the conversion pin must be controlled externally since
we will miss information about when every single conversion cycle (i.e
conversion + data transfer) ends, hence a PWM is introduced to trigger
the conversions.
Reviewed-by: Rob Herring (Arm) <robh@kernel.org>
Signed-off-by: Guillaume Stols <gstols@baylibre.com>
Link: https://patch.msgid.link/20241015-ad7606_add_iio_backend_support-v5-2-654faf1ae08c@baylibre.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
We just need the reset gpio during probe so there's no need to keep it
in our state struct. Hence, move devm_gpiod_get_optional() into
ad74413r_reset() and use a local struct gpio_desc.
While at it, request the gpio in the asserted state (GPIOD_OUT_HIGH) so
that we already perform the reset while requesting the gpio saving us a
call to gpiod_set_value_cansleep().
Also, explicitly include <gpio/consumer.h> for
devm_gpiod_get_optional().
Signed-off-by: Nuno Sa <nuno.sa@analog.com>
Link: https://patch.msgid.link/20241016-dev-ad74413r-minor-improv-v1-1-13c9c769237d@analog.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The BMP3xx and BMP5xx sensors have an interrupt pin which can be used as
a trigger for when there are data ready in the sensor for pick up.
This use case is used along with NORMAL_MODE in the sensor, which allows
the sensor to do consecutive measurements depending on the ODR rate value.
The trigger pin can be configured to be open-drain or push-pull and either
rising or falling edge.
No support is added yet for interrupts for FIFO, WATERMARK and out of range
values.
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Vasileios Amoiridis <vassilisamir@gmail.com>
Link: https://patch.msgid.link/20241017233022.238250-4-vassilisamir@gmail.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Add forced mode support in sensors BMP28x, BME28x, BMP3xx and BMP58x.
Sensors BMP18x and BMP085 are old and do not support this feature so
their operation is not affected at all.
Essentially, up to now, the rest of the sensors were used in normal mode
all the time. This means that they are continuously doing measurements
even though these measurements are not used. Even though the sensor does
provide PM support, to cover all the possible use cases, the sensor needs
to go into sleep mode and wake up whenever necessary.
The idea is that the sensor is by default in sleep mode, wakes up in
forced mode when a oneshot capture is requested, or in normal mode
when the buffer is enabled. The difference lays in the fact that in
forced mode, the sensor does only one conversion and goes back to sleep
while in normal mode, the sensor does continuous measurements with the
frequency that was set in the ODR registers.
The bmpX_chip_config() functions which are responsible for applying
the requested configuration to the sensor, are modified accordingly
in order to set the sensor by default in sleep mode.
DEEP STANDBY, Low Power NORMAL and CONTINUOUS modes, supported only by
the BMP58x version, are not added.
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Vasileios Amoiridis <vassilisamir@gmail.com>
Link: https://patch.msgid.link/20241017233022.238250-2-vassilisamir@gmail.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
add the iio driver for bosch imu smi240. The smi240 is a combined
three axis angular rate and three axis acceleration sensor module
with a measurement range of +/-300°/s and up to 16g. A synchronous
acc and gyro sampling can be triggered by setting the capture bit
in spi read command.
Implemented features:
* raw data access for each axis through sysfs
* tiggered buffer for continuous sampling
* synchronous acc and gyro data from tiggered buffer
Signed-off-by: Shen Jianping <Jianping.Shen@de.bosch.com>
Link: https://patch.msgid.link/20241018135234.5446-3-Jianping.Shen@de.bosch.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Pull bluetooth fixes from Luiz Augusto Von Dentz:
- ISO: Fix multiple init when debugfs is disabled
- Call iso_exit() on module unload
- Remove debugfs directory on module init failure
- btusb: Fix not being able to reconnect after suspend
- btusb: Fix regression with fake CSR controllers 0a12:0001
- bnep: fix wild-memory-access in proto_unregister
Note: normally the bluetooth fixes go through the networking tree, but
this missed the weekly merge, and two of the commits fix regressions
that have caused a fair amount of noise and have now hit stable too:
https://lore.kernel.org/all/4e1977ca-6166-4891-965e-34a6f319035f@leemhuis.info/
So I'm pulling it directly just to expedite things and not miss yet
another -rc release. This is not meant to become a new pattern.
* tag 'for-net-2024-10-16' of git://git.kernel.org/pub/scm/linux/kernel/git/bluetooth/bluetooth:
Bluetooth: btusb: Fix regression with fake CSR controllers 0a12:0001
Bluetooth: bnep: fix wild-memory-access in proto_unregister
Bluetooth: btusb: Fix not being able to reconnect after suspend
Bluetooth: Remove debugfs directory on module init failure
Bluetooth: Call iso_exit() on module unload
Bluetooth: ISO: Fix multiple init when debugfs is disabled
Pull pin control fixes from Linus Walleij:
"Mostly error path fixes, but one pretty serious interrupt problem in
the Ocelot driver as well:
- Fix two error paths and a missing semicolon in the Intel driver
- Add a missing ACPI ID for the Intel Panther Lake
- Check return value of devm_kasprintf() in the Apple and STM32
drivers
- Add a missing mutex_destroy() in the aw9523 driver
- Fix a double free in cv1800_pctrl_dt_node_to_map() in the Sophgo
driver
- Fix a double free in ma35_pinctrl_dt_node_to_map_func() in the
Nuvoton driver
- Fix a bug in the Ocelot interrupt handler making the system hang"
* tag 'pinctrl-v6.12-2' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl:
pinctrl: ocelot: fix system hang on level based interrupts
pinctrl: nuvoton: fix a double free in ma35_pinctrl_dt_node_to_map_func()
pinctrl: sophgo: fix double free in cv1800_pctrl_dt_node_to_map()
pinctrl: intel: platform: Add Panther Lake to the list of supported
pinctrl: aw9523: add missing mutex_destroy
pinctrl: stm32: check devm_kasprintf() returned value
pinctrl: apple: check devm_kasprintf() returned value
pinctrl: intel: platform: use semicolon instead of comma in ncommunities assignment
pinctrl: intel: platform: fix error path in device_for_each_child_node()
Pull misc driver fixes from Greg KH:
"Here are a number of small char/misc/iio driver fixes for 6.12-rc4:
- loads of small iio driver fixes for reported problems
- parport driver out-of-bounds fix
- Kconfig description and MAINTAINERS file updates
All of these, except for the Kconfig and MAINTAINERS file updates have
been in linux-next all week. Those other two are just documentation
changes and will have no runtime issues and were merged on Friday"
* tag 'char-misc-6.12-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc: (39 commits)
misc: rtsx: list supported models in Kconfig help
MAINTAINERS: Remove some entries due to various compliance requirements.
misc: microchip: pci1xxxx: add support for NVMEM_DEVID_AUTO for OTP device
misc: microchip: pci1xxxx: add support for NVMEM_DEVID_AUTO for EEPROM device
parport: Proper fix for array out-of-bounds access
iio: frequency: admv4420: fix missing select REMAP_SPI in Kconfig
iio: frequency: {admv4420,adrf6780}: format Kconfig entries
iio: adc: ad4695: Add missing Kconfig select
iio: adc: ti-ads8688: add missing select IIO_(TRIGGERED_)BUFFER in Kconfig
iio: hid-sensors: Fix an error handling path in _hid_sensor_set_report_latency()
iioc: dac: ltc2664: Fix span variable usage in ltc2664_channel_config()
iio: dac: stm32-dac-core: add missing select REGMAP_MMIO in Kconfig
iio: dac: ltc1660: add missing select REGMAP_SPI in Kconfig
iio: dac: ad5770r: add missing select REGMAP_SPI in Kconfig
iio: amplifiers: ada4250: add missing select REGMAP_SPI in Kconfig
iio: frequency: adf4377: add missing select REMAP_SPI in Kconfig
iio: resolver: ad2s1210: add missing select (TRIGGERED_)BUFFER in Kconfig
iio: resolver: ad2s1210 add missing select REGMAP in Kconfig
iio: proximity: mb1232: add missing select IIO_(TRIGGERED_)BUFFER in Kconfig
iio: pressure: bm1390: add missing select IIO_(TRIGGERED_)BUFFER in Kconfig
...
