Jonathan writes:
IIO: 1st set of new device support, features and cleanup for 6.7
Particularly great to see a resolver driver move out of staging via a
massive set of changes. Only took 13 years :)
One small patch added then reverted due to a report of test breakage
(ashai-kasei,ak8975: Drop deprecated enums.)
An immutable branch was used for some hid-senors changes in case
there was a need to take them into the HID tree as well.
New device support
-----------------
adi,hmc425a
- Add support for HMC540SLP3E broadband 4-bit digital attenuator.
kionix,kx022a
- Add support for the kx132-1211 accelerometer. Require significant
driver rework to enable this including add a chip type specific
structure to deal with the chip differences.
- Add support for the kx132acr-lbz accelerometer (subset of the kx022a
feature set).
lltc,ltc2309
- New driver for this 8 channel ADC.
microchip,mcp3911
- Add support for rest of mcp391x family of ADCs (there are various
differences beyond simple channel count variation.
Series includes some general driver cleanup.
microchip,mcp3564
- New driver for MCP3461, MCP3462, MCP3464, MCP3541, MCP3562, MCP3564
and their R variants of 16/24bit ADCs. A few minor fixed followed.
rohm,bu1390
- New driver for this pressure sensor.
Staging graduation
------------------
adi,ad1210 (after 13 or so years :)
- More or less a complete (step-wise) rewrite of this resolver driver
to bring it up to date with modern IIO standards. The fault signal
handling mapping to event channels was particularly complex and
significant part of the changes.
Features
--------
iio-core
- Add chromacity and color temperature channel types.
adi,ad7192
- Oversampling ratio control (called fast settling in datasheet).
adi,adis16475
- Add core support and then driver support for delta angle and delta
velocity channels. These are intended for summation to establish
angle and velocity changes over larger timescales. Fix was
needed for alignment after the temperature channel. Further fix
reduced set of devices for which the buffer support was applicable
as seems burst reads don't cover these on all devices.
hid-sensors-als
- Chromacity and color temperatures support including in amd sfh.
stx104
- Add support for counter subsystem to this multipurpose device.
ti,twl6030
- Add missing device tree binding description.
Clean up and minor fixes.
------------------------
treewide
- Drop some unused declarations across IIO.
- Make more use of device_get_match_data() instead of OF specific
approaches.
Similar cleanup to sets of drivers.
- Stop platform remove callbacks returning anything by using the
temporary remove_new() callback.
- Use i2c_get_match_data() to cope nicely with all types of ID table
entry.
- Use device_get_match_data() for various platform device to cope
with more types of firmware.
- Convert from enum to pointer in ID tables allowing use of
i2c_get_match_data().
- Fix sorting on some ID tables.
- Include specific string helper headers rather than simply string_helpers.h
docs
- Better description of the ordering requirements etc for
available_scan_masks.
tools
- Handle alignment of mixed sizes where the last element isn't the biggest
correctly. Seems that doesn't happen often!
adi,ad2s1210
- Lots of work from David Lechner on this driver including a few fixes
that are going with the rework to avoid slowing that down.
adi,ad4310
- Replace deprecated devm_clk_register()
adi,ad74413r
- Bring the channel function setting inline with the datasheet.
adi,ad7192
- Change to FIELD_PREP(), FIELD_GET().
- Calculate f_order from the sinc filter and chop filter states.
- Move more per chip config into data in struct ad7192_chip_info
- Cleanup unused parameter in channel macros.
adi,adf4350
- Make use of devm_* to simplify error handling for many of the setup
calls in probe() / tear down in remove() and error paths. Some more
work to be done on this one.
- Use dev_err_probe() for errors in probe() callback.
adi,adf4413
- Typo in function name prefix.
adi,adxl345
- Add channel scale to the chip type specific structure and drop
using a type field previously used for indirection.
asahi,ak8985
- Fix a mismatch introduced when switching from enum->pointers
in the match tables.
amlogic,meson
- Expand error logging during probe.
invensense,mpu6050
- Support level-shifter control. Whilst no one is sure exactly what this
is doing it is needed for some old boards.
- Document mount-matrix dt-binding.
mediatek,mt6577
- Use devm_clk_get_enabled() to replace open coded version and move
everything over to being device managed. Drop now empty remove()
callback. Fix follows to put the drvdata back.
- Use dev_err_probe() for error reporting in probe() callback.
memsic,mxc4005
- Add of_match_table.
microchip,mcp4725
- Move various chip specific data from being looked up by chip ID to
data in the chip type specific structure.
silicon-labs,si7005
- Add of_match_table and entry in trivial-devices.yaml
st,lsm6dsx
- Add missing mount-matrix dt binding documentation.
st,spear
- Use devm_clk_get_enabled() and some other devm calls to move everything
over to being device managed. Drop now empty remove() callback.
- Use dev_err_probe() to better handled deferred probing and tidy up
error reporting in probe() callback.
st,stm32-adc
- Add a bit of additional checking in probe() to protect against a NULL
pointer (no known path to trigger it today).
- Replace deprecated strncpy()
ti,ads1015
- Allow for edge triggers.
- Document interrupt in dt-bindings.
* tag 'iio-for-6.7a' of https://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio: (201 commits)
iio: Use device_get_match_data()
iio: adc: MCP3564: fix warn: unsigned '__x' is never less than zero.
dt-bindings: trivial-devices: add silabs,si7005
iio: si7005: Add device tree support
drivers: imu: adis16475.c: Remove scan index from delta channels
dt-bindings: iio: imu: st,lsm6dsx: add mount-matrix property
iio: resolver: ad2s1210: remove of_match_ptr()
iio: resolver: ad2s1210: remove DRV_NAME macro
iio: resolver: ad2s1210: move out of staging
staging: iio: resolver: ad2s1210: simplify code with guard(mutex)
staging: iio: resolver: ad2s1210: clear faults after soft reset
staging: iio: resolver: ad2s1210: refactor sample toggle
staging: iio: resolver: ad2s1210: remove fault attribute
staging: iio: resolver: ad2s1210: add label attribute support
staging: iio: resolver: ad2s1210: add register/fault support summary
staging: iio: resolver: ad2s1210: implement fault events
iio: event: add optional event label support
staging: iio: resolver: ad2s1210: rename DOS reset min/max attrs
staging: iio: resolver: ad2s1210: convert DOS mismatch threshold to event attr
staging: iio: resolver: ad2s1210: convert DOS overrange threshold to event attr
...
Some devices do not support delta angle and delta velocity
burst readings, which means there should be no buffer support
for these types of channels.
A new list of channels is created which contains the delta
channels structures with the scan index equal to -1 to allow
for raw register readings, without buffer support.
This list of channels is assigned to the devices which
do not support delta angle and delta velocity burst
readings.
Fixes: 8f6bc87d67 ("iio: imu: adis16475.c: Add delta angle and delta velocity channels")
Signed-off-by: Ramona Gradinariu <ramona.gradinariu@analog.com>
Reviewed-by: Nuno Sa <nuno.sa@analog.com>
Link: https://lore.kernel.org/r/20231012122456.765709-2-ramona.gradinariu@analog.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Commit 0f3a8c3f34 ("iio: Add support for creating IIO devices via configfs")
declared but never implemented iio_sw_device_type_configfs_{un}register().
Commit b662f809d4 ("iio: core: Introduce IIO software triggers") declared but
never implemented iio_sw_trigger_type_configfs_{un}register().
Commit a3e0b51884 ("iio: accel: add support for FXLS8962AF/FXLS8964AF accelerometers")
declared but never implemented fxls8962af_core_remove().
Commit 8dedcc3eee ("iio: core: centralize ioctl() calls to the main chardev")
declared but never implemented iio_device_ioctl().
Commit d430f3c36c ("iio: imu: inv_mpu6050: Use regmap instead of i2c specific functions")
removed inv_mpu6050_write_reg() but not its declaration.
Signed-off-by: Yue Haibing <yuehaibing@huawei.com>
Link: https://lore.kernel.org/r/20230811095701.35372-1-yuehaibing@huawei.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
When processing data read the full fifo data in 1 time. If there
are several samples in the FIFO, it means we are experiencing
system delay. In this case, it is better to read all data with 1
bus access than to add additional latency by doing several ones.
This requires to use a bigger buffer depending on chip FIFO size
and do an additional local data copy before sending. But the cost
is minimal and behavior is still better like this under system
heavy load.
Signed-off-by: Jean-Baptiste Maneyrol <jean-baptiste.maneyrol@tdk.com>
Link: https://lore.kernel.org/r/20230623082924.283967-1-inv.git-commit@tdk.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Jonathan writes:
1st set of IIO new device support, features and cleanup for the 6.5 cycle.
New device support
- honeywell,mprls0025pa
* New driver and dt-bindings for this series of pressure sensors.
- invensense,mpu6050
* Add support for ICM 20600 IMU (ID, bindings and device data).
- melexis,mlx90614
* Add support for mlx90615 Infra Red Thermometer after driver cleanup
and refactoring to support the differences in this device.
- renesas,x9250
* New driver and bindings for this quad potentiometer.
- rockchip,saradc
* Add support for RK3588. Also included is a bunch of refactoring and
cleanup for that driver.
- rohm,bu27008
* New driver bindings etc for this 5 photodiode color sensor.
- st,lsm9ds0/st,st-sensors
* ID added for LSM303D accelerometer and magnetometer including ACPI binding.
- ti,opt4001
* New driver and bindings for this ambient light sensor.
Features
- core
* Introduce iio_validate_own_trigger() for cases where a driver can only
consumer a trigger it registered (detected via same parent device).
Use it in the kionix,kx022a driver and new rohm,by27008 driver.
- dynaimage,al3320a
* ACPI binding CALS0001 seen on Lenovo Yoga Table 2 devices.
- kionix,kx002a
* Enable asynchronous probe.
- rohm,bu27034
* Enable asynchronous probe.
- ti,tmp006
* Explicit support for DT including binding documentation.
Cleanups, minor fixes and misc improvements.
- treewide
* Switch I2C drivers from probe_new() back to probe() - part of the
long process of getting rid of a parameter from probe()
* Various whitespace and typo fixes not otherwise called out.
- core
* industrialio-buffer,Style cleanup.
* Add documentation to extend_name field of struct iio_chan_spec to
direct people using it towards the label infrastructure instead.
extend_name was a design mistake a long time back so directly people
away from it may be useful.
- adi,ad7606
* Add HAS_IOPORT dependency to prepare for some Kconfig changes.
- bosch,bma400
* Drop pointless print of ret in a dev_err_probe() message.
- invensense,icm42600
* Rework timestamp handling to reduce jitter.
- mediatek,mt7986-auxdac
* Add DT binding for this part.
- qcom,spmi-vadc
* Allow for 1/16th prescaling used on a few devices.
* Various changes to channel labeling and naming, including dropping
use of fwnode_name which generates odd channel names. Small ABI
change as a result, but not thought to be a problem for users of this
platform.
- st,lsm6dsx
* dt-binding: Use common schema for mount-matrix via a reference.
- st,stm32
* Add a debug print for when legacy channel config is used.
- ti,palmas-adc
* Drop unused i2c.h include.
* tag 'iio-for-6.5a' of https://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio: (59 commits)
dt-bindings: iio: rockchip: Fix 'oneOf' condition failed warning
dt-bindings: iio: afe: voltage-divider: Spelling s/curcuit/circuit/
dt-bindings: iio: adc: Add rockchip,rk3588-saradc string
iio: adc: rockchip_saradc: Use dev_err_probe
iio: adc: rockchip_saradc: Match alignment with open parenthesis
iio: adc: rockchip_saradc: Use of_device_get_match_data
iio: adc: rockchip_saradc: Make use of devm_clk_get_enabled
iio: adc: rockchip_saradc: Add support for RK3588
iio: adc: rockchip_saradc: Add callback functions
iio: temperature: tmp006: Add OF device matching support
dt-bindings: iio: temperature: Add support for tmp006
staging: iio: Switch i2c drivers back to use .probe()
iio: amplifiers: ad8366 Fix whitespace issue
iio: imu: inv_icm42600: avoid frequent timestamp jitter
MAINTAINERS: Add ROHM BU27008
iio: light: ROHM BU27008 color sensor
iio: kx022a: Use new iio_validate_own_trigger()
iio: trigger: Add simple trigger_validation helper
dt-bindings: iio: light: ROHM BU27008
iio: mlx90614: Add MLX90615 support
...
We are currently synchronizing every time the data timestamp with
the IT timestamp, leading to system jitter jamming timestamps.
To fix that and keep it simple, let's just synchronize when the
delta is bigger than the acceptable jitter, and keep
synchronization at the jitter value.
The result is much stable timestamps reflecting better the real
physical value. Example @50Hz delta timestamp,
* before: 20.123ms, 19.721ms, 20.023ms, 20.353ms, 19.821ms, ...
* after: 20.173ms, 20.173ms, 20.173ms, 20.40ms, 20.173ms, ...
Refactorize code and delete the unnecessary handling of multiple
FIFO data.
Signed-off-by: Jean-Baptiste Maneyrol <jean-baptiste.maneyrol@tdk.com>
Link: https://lore.kernel.org/r/20230522093210.817212-1-inv.git-commit@tdk.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Pull char/misc drivers updates from Greg KH:
"Here is the "big" set of char/misc and other driver subsystems for
6.4-rc1.
It's pretty big, but due to the removal of pcmcia drivers, almost
breaks even for number of lines added vs. removed, a nice change.
Included in here are:
- removal of unused PCMCIA drivers (finally!)
- Interconnect driver updates and additions
- Lots of IIO driver updates and additions
- MHI driver updates
- Coresight driver updates
- NVMEM driver updates, which required some OF updates
- W1 driver updates and a new maintainer to manage the subsystem
- FPGA driver updates
- New driver subsystem, CDX, for AMD systems
- lots of other small driver updates and additions
All of these have been in linux-next for a while with no reported
issues"
* tag 'char-misc-6.4-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc: (196 commits)
mcb-lpc: Reallocate memory region to avoid memory overlapping
mcb-pci: Reallocate memory region to avoid memory overlapping
mcb: Return actual parsed size when reading chameleon table
kernel/configs: Drop Android config fragments
virt: acrn: Replace obsolete memalign() with posix_memalign()
spmi: Add a check for remove callback when removing a SPMI driver
spmi: fix W=1 kernel-doc warnings
spmi: mtk-pmif: Drop of_match_ptr for ID table
spmi: pmic-arb: Convert to platform remove callback returning void
spmi: mtk-pmif: Convert to platform remove callback returning void
spmi: hisi-spmi-controller: Convert to platform remove callback returning void
w1: gpio: remove unnecessary ENOMEM messages
w1: omap-hdq: remove unnecessary ENOMEM messages
w1: omap-hdq: add SPDX tag
w1: omap-hdq: allow compile testing
w1: matrox: remove unnecessary ENOMEM messages
w1: matrox: use inline over __inline__
w1: matrox: switch from asm to linux header
w1: ds2482: do not use assignment in if condition
w1: ds2482: drop unnecessary header
...
Pull spi updates from Mark Brown:
"A fairly standard release for SPI with the exception of a change to
the API for specifying chip selects done in preparation for supporting
devices with more than one chip select, this required some mechanical
changes throughout the tree which have been cooking in -next happily
for a while.
There's also a new API to allow us to support TPM chips on half duplex
controllers.
Summary:
- Refactoring in preparation for supporting multiple chip selects for
a single device, needed by some flash devices, which required a
change in the SPI device API visible throughout the tree
- Support for hardware assisted interaction with SPI TPMs on half
duplex controllers, implemented on nVidia Tedra210 QuadSPI
- Optimisation for large transfers on fsl-cpm devices
- Cleanups around device property use which fix some sisues with
fwnode
- Use of both void remove() and devm_platform_.*ioremap_resource()
- Support for AMD Pensando Elba, Amlogic A1, Cadence device mode,
Intel MetorLake-S and StarFive J7110 QuadSPI"
* tag 'spi-v6.4' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi: (185 commits)
spi: bcm63xx: use macro DEFINE_SIMPLE_DEV_PM_OPS
spi: tegra210-quad: Enable TPM wait polling
spi: Add TPM HW flow flag
spi: bcm63xx: remove PM_SLEEP based conditional compilation
spi: cadence-quadspi: use macro DEFINE_SIMPLE_DEV_PM_OPS
spi: spi-cadence: Add support for Slave mode
spi: spi-cadence: Switch to spi_controller structure
spi: cadence-quadspi: fix suspend-resume implementations
spi: dw: Add support for AMD Pensando Elba SoC
spi: dw: Add AMD Pensando Elba SoC SPI Controller
spi: cadence-quadspi: Disable the SPI before reconfiguring
spi: cadence-quadspi: Update the read timeout based on the length
spi: spi-loopback-test: Add module param for iteration length
spi: add support for Amlogic A1 SPI Flash Controller
dt-bindings: spi: add Amlogic A1 SPI controller
spi: fsl-spi: No need to check transfer length versus word size
spi: fsl-spi: Change mspi_apply_cpu_mode_quirks() to void
spi: fsl-cpm: Use 16 bit mode for large transfers with even size
spi: fsl-spi: Re-organise transfer bits_per_word adaptation
spi: fsl-spi: Fix CPM/QE mode Litte Endian
...
ID seen in the wild and it is a valid ST micro ID.
An offset of 1 for the device ID enum is needed when adding support for
retrieving the ID from device_get_match_data() to allow detection of
NULL pointer and fallback to i2c_device_id table.
DSDT chunk cropped for relevant parts.
Scope (_SB.PCI0.I2C5)
{
Device (DEV)
{
Name (_HID, EisaId ("SMO8B30")) // _HID: Hardware ID
Name (_CID, EisaId ("SMO8B30")) // _CID: Compatible ID
Name (_UID, Zero) // _UID: Unique ID
Method (_CRS, 0, NotSerialized) // _CRS: Current Resource Settings
{
Name (RBUF, ResourceTemplate ()
{
I2cSerialBusV2 (0x006A, ControllerInitiated, 0x00061A80,
AddressingMode7Bit, "\\_SB.PCI0.I2C5",
0x00, ResourceConsumer, , Exclusive,
)
})
Return (RBUF) /* \_SB_.PCI0.I2C5.DEV_._CRS.RBUF */
}
Method (ROTM, 0, NotSerialized)
{
Name (RBUF, Package (0x03)
{
"0 -1 0",
"1 0 0",
"0 0 1"
})
Return (RBUF) /* \_SB_.PCI0.I2C5.DEV_.ROTM.RBUF */
}
...
Link: https://lore.kernel.org/all/20230129182441.082f29d0@jic23-huawei/
Reported-by: Darrell Kavanagh <darrell.kavanagh@gmail.com>
Tested-by: Darrell Kavanagh <darrell.kavanagh@gmail.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Link: https://lore.kernel.org/r/20230130201018.981024-2-jic23@kernel.org
Jonathan writes:
1st set of IIO new device support, features and cleanups for the 6.4 cycle.
New device support
* bosch,bmp280
- Add support for BMP580 - includes significant refactoring and general
driver cleanup + support for non-volatile memory for trimming and config
parameters.
* rohm BU27034
- New driver for this 3 channel ambient light sensor.
- New support library for devices where both integration time and
amplifier gain are configurable. In these cases a scale change
may require changing bother underlying values. This library module
provides code to help with this.
* st,accel
- Add support for IIS328DQ (ID only as compatible wtih LIS331DL)
* st,lsm6dsx
- Add support for ASM330LHB automotive MEMS sensor.
* ti,ads1100, ads1000
- New driver for these 16 bit ADCs.
* ti,tmp117
- Add support for older tmp116 device. Includes some general driver cleanup.
Staging driver drops
* adi,ade7854
- Driver was a very long way from compliant with IIO infrastructure and ABI.
If anyone wants a non staging version of this driver they are better off
starting from scratch. Hence drop it and the associated meter.h header.
Features
* adi,ad7441r
- Add DT binding to set sink current for digital input.
* semtech,sx9324,9360
- Support older register mapping from firmware designed for windows.
Core improvements.
* Move iio_trigger_poll() docs to next to the implementation and add a note
on expected caller context.
* Rename iio_trigger_poll_chained() to iio_trigger_poll_nested() so
as to use more standard / common terminology.
* Improve main ABI docs references to offset and scale for raw values by
making them consistent and clear.
Cleanups and minor fixes:
* adi,ad5592r
- Add GPIO names - useful for debug.
* adi,ad7441r
- Fix current input, loop powered mode configuration setup.
* adi,adis16475
- Fix wrong commented value for minimum advised lower rate.
* adi,admv1013
- Use devm_clk_get_enabled() to reduce boilerplate.
* adi,ads1210
- Fix wrong bits for writing config register (late fix and has
been broken a long time so not rushed upstream)
* amlogic,meson-saradc
- Improve cleanup in error handling if BL30 handshake fails.
* apex-embedded,stx104
- Migrate to regmap and use regmap_read_poll_timeout() to neatly handle
retries.
- Add local mutex to close various races.
- Use define U16_MAX rather than value for limit.
- Improve code readability with minor reorganization.
* atmel,ad91-sama5d2
- Drop trivial dead code.
* kionix,kx022a
- Drop unused structure element.
* linear,ltc2983
- Reorganize bindings doc to enable unevaluatedProperties to be set
in one place for all child nodes.
- Make binding for adi,custom-thermocouple accept signed values.
* maxim,max44000
- Add OF Device matching (of_match_table was not correctly set).
* maxim,max5522
- Missing static
* measurement-computing,cio-dac
- Fix wrong part name in comments.
- Migrate to regmap.
- Improve includes by replacing bitops.h with more direct bits.h
* qcom,pm8xxx-xoadc
- Remove a check that can never fail.
* renesas,rcar-gyroadc
- DT binding documentation improvements.
- Tidy up an unused warning with __maybe_unused.
* semtech,sx_common
- Drop docs for a structure element that doesn't exist.
* semtech,sx9500
- Drop ACPI_PTR() and of_match_ptr() protections that just complicate
the code / block some firmware registration types that would otherwise
work.
* sensiron,sps30
- Comment formatting tidy up.
* st,sensors
- Drop duplicate text in DT binding.
* st,stm32-adc
- Add some missing static markings.
* ti,ads1100
- Use correct return code in dev_err_probe() call.
* x-powers,axp20x_adc - precursor series to simplify addition of AXP192.
- General code cleanup / minor refactoring for better readabilty of code.
- Switch from boolean value to mask for adc_en2 field to avoid hard coding
a mask that will be different in AXP192
* tag 'iio-for-6.4a' of https://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio: (63 commits)
MAINTAINERS: Add ROHM BU27034
iio: light: ROHM BU27034 Ambient Light Sensor
dt-bindings: iio: light: Support ROHM BU27034
MAINTAINERS: Add IIO gain-time-scale helpers
iio: light: Add gain-time-scale helpers
doc: Make sysfs-bus-iio doc more exact
iio: dac: set variable max5522_channels storage-class-specifier to static
dt-bindings: iio: temperature: ltc2983: Make 'adi,custom-thermocouple' signed
dt-bindings: iio: temperature: ltc2983: Fix child node unevaluated properties
iio: addac: stx104: Use regmap_read_poll_timeout() for conversion poll
iio: addac: stx104: Migrate to the regmap API
iio: addac: stx104: Improve indentation in stx104_write_raw()
iio: addac: stx104: Use define rather than hardcoded limit for write val
iio: addac: stx104: Fix race condition when converting analog-to-digital
iio: addac: stx104: Fix race condition for stx104_write_raw()
dt-bindings: iio: st-sensors: Fix repeated text
staging: iio: resolver: ads1210: fix config mode
iio: adc: ti-ads1100: fix error code in probe()
iio: accel: add support for IIS328DQ variant
dt-bindings: iio: st-sensors: Add IIS328DQ accelerometer
...
Jonathan writes:
1st set of IIO fixes for 6.3
Usual mixed bag:
- core - output buffers
Fix return of bytes written when only some succeed.
Fix O_NONBLOCK handling to not block.
- adi,ad7791
Fix IRQ type. Not confirmed to have any impact but good to correct it anyway
- adi,adis16400
Missing CONFIG_CRC32
- capella,cm32181
Unregister 2nd I2C client if one is used.
- cio-dac
Fix bitdepth for range check on write.
- linear,ltc2497
Fix a wrong shift of the LSB introduced when switching to be24 handling.
- maxim,max11410
Fix handling of return code in read_poll_timeout()
- qcom,spmi-adc
Fix an accidental change of channel name to include the reg value from OF.
- ti,palmas
Fix a null dereference on remove due to wrong function used to get the
drvdata.
- ti,ads7950
Mark GPIO as can sleep.
* tag 'iio-fixes-for-6.3a' of https://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio:
iio: adc: ti-ads7950: Set `can_sleep` flag for GPIO chip
iio: adc: palmas_gpadc: fix NULL dereference on rmmod
iio: adc: max11410: fix read_poll_timeout() usage
iio: dac: cio-dac: Fix max DAC write value check for 12-bit
iio: light: cm32181: Unregister second I2C client if present
iio: accel: kionix-kx022a: Get the timestamp from the driver's private data in the trigger_handler
iio: adc: ad7791: fix IRQ flags
iio: buffer: make sure O_NONBLOCK is respected
iio: buffer: correctly return bytes written in output buffers
iio: light: vcnl4000: Fix WARN_ON on uninitialized lock
iio: adis16480: select CONFIG_CRC32
drivers: iio: adc: ltc2497: fix LSB shift
iio: adc: qcom-spmi-adc5: Fix the channel name
Supporting multi-cs in spi drivers would require the chip_select & cs_gpiod
members of struct spi_device to be an array. But changing the type of these
members to array would break the spi driver functionality. To make the
transition smoother introduced four new APIs to get/set the
spi->chip_select & spi->cs_gpiod and replaced all spi->chip_select and
spi->cs_gpiod references with get or set API calls.
While adding multi-cs support in further patches the chip_select & cs_gpiod
members of the spi_device structure would be converted to arrays & the
"idx" parameter of the APIs would be used as array index i.e.,
spi->chip_select[idx] & spi->cs_gpiod[idx] respectively.
Signed-off-by: Amit Kumar Mahapatra <amit.kumar-mahapatra@amd.com>
Acked-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Reviewed-by: Michal Simek <michal.simek@amd.com>
Link: https://lore.kernel.org/r/20230310173217.3429788-4-amit.kumar-mahapatra@amd.com
Signed-off-by: Mark Brown <broonie@kernel.org>
During digital filters settling time the driver is expected to drop
samples since they can be corrupted. Introduce the capability to drop
a given number of samples according to the configured ODR.
Add sample_to_discard for LSM6DSM-like sensors since new generation
devices (e.g. LSM6DSO) support DRDY mask where corrupted samples are
masked in hw with values greather than 0x7ffd so the driver can easily
discard them.
I have not added sample_to_discard support for LSM6DS3 or LSM6DS3H since
I do not have any sample for testing at the moment.
Reported-by: Philippe De Muyter <phdm@macqel.be>
Tested-by: Philippe De Muyter <phdm@macqel.be>
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Link: https://lore.kernel.org/r/21dcd94935c147ef9b1da4984b3da6264ee9609e.1677496295.git.lorenzo@kernel.org
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
+/-1200uT is a MAGN sensor full measurement range. Magnetometer scale
is the magnetic sensitivity parameter. It is referenced as 0.1uT
according to datasheet and magnetometer channel unit is Gauss in
sysfs-bus-iio documentation. Gauss and uTesla unit conversion
relationship as follows: 0.1uT = 0.001Gs.
Set magnetometer scale and available magnetometer scale as fixed 0.001Gs.
Fixes: 84e5ddd5c4 ("iio: imu: Add support for the FXOS8700 IMU")
Signed-off-by: Carlos Song <carlos.song@nxp.com>
Link: https://lore.kernel.org/r/20230118074227.1665098-5-carlos.song@nxp.com
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The following kernel linkage error:
st_lsm6dsx_core.o: in function `st_lsm6dsx_sw_buffers_setup':
st_lsm6dsx_core.c:2578: undefined reference to `devm_iio_triggered_buffer_setup_ext'
is caused by the fact that the object owning devm_iio_triggered_buffer_setup_ext()
(drivers/iio/buffer/industrialio-triggered-buffer.o) is allowed to be
built as module when its user (drivers/iio/imu/st_lsm6dsx/st_lsm6dsx_core.c)
is built-in.
The st_lsm6dsx driver already has a "select IIO_BUFFER", so add another
select for IIO_TRIGGERED_BUFFER, to make that option follow what is set
for the st_lsm6dsx driver. This is similar to what other iio drivers do.
Fixes: 2cfb2180c3 ("iio: imu: st_lsm6dsx: introduce sw trigger support")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Link: https://lore.kernel.org/r/20230103130348.1733467-1-vladimir.oltean@nxp.com
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
When device is in active mode, it fails to set an ACCEL full-scale
range(2g/4g/8g) in FXOS8700_XYZ_DATA_CFG. This is not align with the
datasheet, but it is a fxos8700 chip behavior.
Keep the device in standby mode before setting ACCEL full-scale range
into FXOS8700_XYZ_DATA_CFG in chip initialization phase and setting
scale phase.
Fixes: 84e5ddd5c4 ("iio: imu: Add support for the FXOS8700 IMU")
Signed-off-by: Carlos Song <carlos.song@nxp.com>
Link: https://lore.kernel.org/r/20221208071911.2405922-6-carlos.song@nxp.com
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
ACCEL output data registers contain the X-axis, Y-axis, and Z-axis
14-bit left-justified sample data and MAGN output data registers
contain the X-axis, Y-axis, and Z-axis 16-bit sample data. The ACCEL
raw register output data should be divided by 4 before sent to
userspace.
Apply a 2 bits signed right shift to the raw data from ACCEL output
data register but keep that from MAGN sensor as the origin.
Fixes: 84e5ddd5c4 ("iio: imu: Add support for the FXOS8700 IMU")
Signed-off-by: Carlos Song <carlos.song@nxp.com>
Link: https://lore.kernel.org/r/20221208071911.2405922-5-carlos.song@nxp.com
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The length of ACCEL and MAGN 3-axis channels output data is 6 byte
individually. However block only read 3 bytes data into buffer from
ACCEL or MAGN output data registers every time. It causes an incomplete
ACCEL and MAGN channels readback.
Set correct value count for regmap_bulk_read to get 6 bytes ACCEL and
MAGN channels readback.
Fixes: 84e5ddd5c4 ("iio: imu: Add support for the FXOS8700 IMU")
Signed-off-by: Carlos Song <carlos.song@nxp.com>
Link: https://lore.kernel.org/r/20221208071911.2405922-4-carlos.song@nxp.com
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Jonathan writes:
2nd set of IIO new device support, cleanups etc for 6.2
Includes a few late breaking fixes for old issues.
Contains a large set of conversions from i2c probe() to probe_new()
as part of an attempt to finally get rid of the old style probe().
New devices support
* adi,ad74115
- New driver for this complex input/output device with 16 bit ADCs,
14 bit DACs amongst other features.
- A few tidy ups / removal of unused data patches followed.
* adi,adf4377
- New driver for this dual output integer-N phased locked loop and VCO
chip.
* maxim,max30208
- New driver for this high accuracy digital temperature sensor.
* st,lsm6dsx
- Support for LSM6DS016IS (chip specific data)
- Support for ISM330IS (id entry only)
Minor cleanups etc
* adi,adis
- Fix a deadlock on device instance specific mutex.
- Tidy up by calling unlocked form of __adis_initial_startup() in all
cases and dropping the locked version.
* adi,ad4130
- Reference spi-peripehral-props.yaml in the dt-binding.
* adi,ad74413r
- Fix a bug brought on by integer promotion of signed value to unsigned type.
- Add an spi_device_id table to allow module autoloading to work.
- Add support for reset pin.
* adi,ad7606_par
- devm_platform_get_and_ioremap_resource() instead of opencoding.
* adi,ad7923
- Add dt-bindings docs for ad7927 via a fallback to ad7928 and do similar
for ad7924.
* adi,ltc2983
- Drop a now unneeded $ref for -nanoamp property as dt-schema no covers this
unit.
* maxim,max11410
- Fix mask due to repeated use of VREFN instead of one of them being VREFP.
* qcom,spmi-iadc
- Add fallback compatibles to dt-binding.
* renesas,rzg2l
- Document use for RZ/Five SoC.
* st,stm32-adc
- Improved calibration support with error logging and a debugfs
interface to read back the result.
* ti,adc128s052
- Fix an issue with missing data members in the adc128_of_match table that
meant all device were being handled as adc128s052 ADCs.
* tag 'iio-for-6.2b' of https://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio: (178 commits)
iio: addac: ad74413r: fix blank line after declaration warning
iio: addac: ad74115: remove unused ad74115_dac_slew_rate_hz_tbl
dt-bindings: iio: imu: st_lsm6dsx: add ism330is
iio: imu: st_lsm6dsx: add support to ISM330IS
iio: frequency: adf4377: add support for ADF4377
dt-bindings: iio: frequency: add adf4377 doc
dt-bindings: iio: adc: ad4130: use spi-peripheral-props.yaml
dt-bindings: iio: temperature: ltc2983: drop $ref for -nanoamp properties
dt-bindings: iio: adc: renesas,rzg2l-adc: Document RZ/Five SoC
iio: adc128s052: add proper .data members in adc128_of_match table
iio: adc: stm32-adc: add debugfs to read raw calibration result
iio: adc: stm32-adc: improve calibration error log
iio: adc: stm32-adc: smart calibration support
iio: addac: ad74413r: add support for reset-gpio
dt-bindings: iio: ad74413r: add optional reset-gpios
iio: addac: ad74413r: add spi_device_id table
dt-bindings: iio/adc: qcom,spmi-iadc: use double compatibles
dt-bindings: iio: imu: st_lsm6dsx: add lsm6dso16is
iio: imu: st_lsm6dsx: add support to LSM6DSO16IS
iio: addac: add AD74115 driver
...
